Search

Railguns are current-driven guns that allow reaching large muzzle velocities and energies. In the military context, the long-range artillery scenario makes use of these two capabilities to enable the launch of hypervelocity projectiles to target distances above 100 km. As of today, the most advanced railgun project is conducted by the Office of Naval Research, Arlington, VA, USA, and features railguns with a muzzle energy of 32 MJ. Such large artillery railgun systems with efficiencies above 30% are fed by a pulsed power system with a nominal energy content of about 100 MJ. In contrast to this, experiments with French-German Research Institute’s (ISL) most powerful railgun, PEGASUS, have reached muzzle energies of 2 MJ, only. The nearer future ISL has to answer two questions: 1) is the railgun technology adequate for a long-range artillery scenario? 2) can the railgun launch a hypervelocity projectile which is being developed by other groups in ISL? To do so and to support the development of the hypervelocity projectile, a larger railgun installation with a significant increase of the energy and free flight capability is required. In this paper, three different railgun systems were investigated using an electric circuit simulation code. The systems are referred to by the energy being stored in the capacitors as 25, 50, and 100 MJ. The aim of this paper is to investigate what masses can be accelerated to the relevant velocity range for the long-range artillery scenario by these different primary energies. The results of this paper can be used to aid the decision about the required size, with respect to the military scenario, of a potential future railgun system. [ABSTRACT FROM AUTHOR]

A new modular pulsed-power source with fast rise time and step-wise arbitrary output waveform generation is currently under development to drive the Gepulste Elektronenstrahlanlage device investigated at the Institute for Pulsed Power and Microwave Technology (IHM). Acknowledging the complex design procedures necessary to set up a modular pulsed-power source for voltages of up to 120 kV, this paper focuses on the circuit design for a single stage and its validation prior to the generator assembly. Using a semiconductor-based Marx generator topology, the stages are designed to have an output voltage of 1 kV with a pulse current of up to 600 A. When connected to an ohmic load, the measured current rise times are in the order of 46 ns resulting in the current rise rates of up to 10 kA/ $\mu \text{s}$ using the commercial devices. The step-wise arbitrary output waveform is created by generating the switching commands on the stage using a microprocessor and a fast optical synchronization unit. Effective stage shielding is verified by operating the stage in a 100-kV, 2.5-kA electromagnetic interference test bed. This paper presents the design considerations and the corresponding measurements. [ABSTRACT FROM AUTHOR]

The linear induction launcher consists of two parts: the barrel section and the projectile section. The barrel contains of a long coaxial sectionalized group of coils that are energized by a capacitor bank or generator sets. This paper deals with the design, implementation, and experimental test of a coreless axial-flux permanent magnet (AFPM) pulsed alternator with a flywheel system as an energy source for linear induction coil launchers. The proposed coreless AFPM generator has a low internal inductance and resistance of stator windings without compensation windings when compared with the conventional iron core machines. This paper describes the coreless AFPM generator configuration and shows the simulation findings. [ABSTRACT FROM AUTHOR]

Because it possesses higher current turn-off capability, the inverse current commutation with semiconductor devices (ICCOS) is a better option for the opening switch of an inductive pulsed power supply than the integrated gate commutated thyristor. This paper investigates the counter-current capacitor, which is the key component that determines the turn-off result and the volume of the counter-current branch. The major contributions of this paper include the following: 1) deriving an analytical expression for the minimum precharged capacitor voltage that can reliably turn off the main switch; 2) verifying this expression through a series of experiments within a current range of 0 to 4000 A and an energy range of 0 to 50 kJ; 3) giving an approximate expression for the optimal capacitance that minimizes the precharged energy; and 4) investigating the variation trends of the optimal capacitance and the corresponding optimal precharged energy with varying inductor current. [ABSTRACT FROM PUBLISHER]

Based on the urgent needs for modularization and miniaturization of the inductive pulsed power supply system, this paper proposes the conceptual design and comparison of 100-kJ inductive storage power modules including four circuit topologies, three of which are proposed in our previous researches. The four circuit topologies are the STRETCH meat grinder, the XRAM with STRETCH meat grinder unit, the XRAM with strongly coupled inductors, and the XRAM with magnetic flux compression effect. The maximum load current of each constructed module is set to be 50 kA and its pulsewidth is at least 5 ms, which are the same as the main electrical properties of an existing 100-kJ capacitive module. A comparative study on energy density among the constructed inductive modules and the existing capacitive module is carried out in depth. Results show that the inductive modules, considering the volume of semiconductor switches and their control circuits, have higher energy density than that of the capacitive module. Among four constructed inductive modules, the XRAM with strongly coupled inductors module has the highest inductive energy density, and the XRAM with magnetic flux compression effect module has relatively better comprehensive performance. This paper offers the theoretical analysis foundation for investigating the inductive pulse power supply with higher energy. [ABSTRACT FROM PUBLISHER]

Superconducting pulsed-power supply (SPPS) provides an efficient method for both high-density inductive energy storage and high current pulse generation. An SPPS consisting of eight high-temperature superconducting pulsed-power transformer (HTSPPT) modules with XRAM methodology was designed and simulated in preliminary studies. It recycled the leakage flux energy and reduced the voltage across the opening switch with a capacitor in primary. However, the SPPS with XRAM methodology has two problems. The first one is that it can provide high pulse amplitude, but cannot provide enough width. The other one is that the ratio of the maximum capacitive energy over the total inductive energy is relatively large, which cuts down the overall system energy density. This paper proposes a modified topology of SPPS with capacitor reuse methodology. Multiple HTSPPT modules are divided into several groups. Each group shares the same capacitor. The procedure of the modified SPPS is presented in detail. A 270-kJ SPPS with capacitor reuse methodology is designed and simulated to illustrate the modified topology. With the load parameters of a small railgun, the peak value of the load current is 207.15 kA and the pulse half-height width is 5.56 ms, the ratio of the maximum capacitive energy over the total inductive energy is 11%. The characteristics of the modified topology are also described in detail in this paper. [ABSTRACT FROM PUBLISHER]

This paper is aimed at finding the effect of varying inductive energy storage systems’ (IESSs) inductance on resistance of an electrically exploded conductor-based opening switch and profile of current transferred into load, which has not yet been fully understood. Based on experimental results obtained, it is observed that when the inductance of IESS is varied, the magnitude of load current changes so as to conform to the magnetic flux conservation law but its rise time remains unchanged. Resistance of the opening switch and energy deposited in it has been estimated using recorded voltage and current waveforms. It has been found that with increasing inductance of IESS, the resistance of switch increases, whereas energy deposited in it decreases. Using these estimated values of energy, a possible explanation of observed behavior in resistance is presented. Effect of a mismatch between the inductance of IESS and load is seen to only affect the energy transfer efficiency or magnitude of load current but not its rise time emphasizing the novel finding that for a given load, the rise time of load current is independent of the inductance of IESS. [ABSTRACT FROM AUTHOR]

The challenging demands of pulsed electron beam devices (such as the GESA device) with respect to their pulsed power supply have led to the development of a new semiconductor-based Marx generator. At a maximum output voltage of 120 kV and 600-A pulse current for a duration of up to 100 $\mu \text{S}$ , stepwise arbitrary output waveforms are desired. A fast rise time of the generator is achieved by using fast switching circuitry, low inductance capacitors, and a low inductance stage arrangement. For low jitter triggering of all stages and efficient signal transmission, the generator uses an optical bus system for communication. Due to the inherent dynamic load characteristics of the GESA device, the generator features a fast overcurrent protection scheme. This paper presents selected design aspects of the generator and their validation in a small-scale assembly able of delivering up to 8 kV at 600-A load current. [ABSTRACT FROM AUTHOR]

Large railguns require powerful power supply units. At the French-German Research Institute of Saint-Louis (ISL), most experimental railguns are driven by power supply units based on capacitors. Recent investigations at ISL explore the possibility to use coil-based systems to increase the energy density and reduce the footprint of the power supply. In this paper, an electrical circuit simulation is used to investigate the difference for railgun operation in between a capacitor and a coil-based power supply with respect to the current amplitude behavior, projectile velocity, and launch efficiency. For this, a scenario of a 25-MJ muzzle energy railgun is simulated with two different power supply options; one is based on capacitors, and the other is on coils. The circuit resistance determines a large part of the losses of the system and therefore defines the efficiency of the launch and the size of the power supply. Therefore, a range of different resistances were simulated as well. The interpretation of the results of the performed simulations leads to the conclusion that the capacitor-based system “naturally” produces a favorable current pulse trace with respect to launching a mechanical delicate payload. Further simulations show that the disadvantage of the inductor-based supply can be mitigated by increasing the power supply unit subdivision into smaller units. [ABSTRACT FROM AUTHOR]

This paper puts forward a repetitive high-voltage pulse modulator, consisting of a step-up pulse transformer to decrease the number of needed semiconductor switches, and a bipolar Marx generator to reduce the turns ratio of PT, leakage inductance, and distributed capacitance, and also to improve the pulse shape. An equivalent circuit of the proposed modulator considering parasitic elements is established. Based on the equivalent circuit, circuit operation is analyzed in detail. In order to verify the theory analysis and circuit operation, simulations are conducted. In addition, a laboratory prototype is implemented. The simulations and experimental results of resistive load and dielectric-barrier discharges load turn out matched quite well with the theory analysis, demonstrating that the prototype can operate with a voltage amplitude in the range of 0–25 kV, a repetition rate of 0.1–5-kHz stably. [ABSTRACT FROM AUTHOR]

Electromagnetic induction coilgun systems have been receiving great attention, recently, due to the advantage of noncontact between the stator and armature coils. Several studies present the simulation and analysis of the coilgun system by using the finite-element method. However, there are still deficiencies in current modeling studies of the coilgun system. This paper presents a design of a multistage pulsed power induction coilgun system using the Taguchi method to maximize its efficiency and reduce the time and cost of the design process. A coilgun system is analyzed and designed using a state-space equation system. The Taguchi method is applied in order to evaluate and determine the geometric variables, the layer, turn layer numbers for both the stator and armature coils, and the trigger positions of each stage. Then, a 2-D finite-element model of the coilgun system using the MagNet program was developed to compare the design and analysis results. The energy efficiency of the three-stage coilgun system is 31.3%, and this is expected to increase with the increase in the number of stages. [ABSTRACT FROM AUTHOR]

Optimal design and selection of arm inductances have been as a challenging subject in the field of modular multilevel converter (MMC). The average steady-state model is generally used as the analytical circuit model that neglects the switching frequency and harmonic values. Also, most of the researchers neglect the saturation effect of inductor core to simplify the analytical model. Contrary to the transformers, choosing the maximum flux density of inductance core is a sensitive issue, in order to design and minimize the inductors. Increasing the flux density reduces the inductor size, but getting close to the saturation region might alter the performance of the converter. This paper presents a systematic optimization approach to minimize high-power MMCs with saturable arm inductance considering technical, thermal, and manufacturing constraints. An accurate steady-state analytical model of MMC converter has been proposed and verified. A combination of converter circuit model and inductance electromagnetic model is employed to find the optimal arm inductances and capacitor values. The effect of nonideal inductance core on converter outputs has been investigated. A dimensioning model of inductor consisting of electromagnetic and thermal models is presented. To compute the optimal inductor size, a novel hybrid optimization loop is proposed including the analytical model of the converter and the inductor in which circuit, electromagnetic, and thermal properties are taken into consideration. In order to increase the accuracy of the dimensioning model, an internal verification loop is employed to verify and correct the analytical model using finite-element analysis. The proposed optimization loop aims to find the minimum inductor size considering technical and manufacturing constraints. Finally, the converter mass sensitivity of MMC converter versus some important constraints, such as temperature rise and capacitor ripple, has been investigated. [ABSTRACT FROM AUTHOR]

This paper describes the design and implementation of novel trigger circuit (23 kV, $1.7~\mu \text{s}$ , and 0.66 J/pulse) for xenon flash lamp driver. The design is based on a modified flyback circuit in the discontinuous conduction mode to take advantage of both generating the high voltage from the resonance with output capacitor and connecting the series with main pulse circuit using the flyback transformer which can carry the full current of several kiloampere at high-voltage side. This design eliminates the requirement for additional high-voltage protection devices in a xenon flash lamp driver. In addition, the unique high-voltage flyback transformer is designed with high turn ratio and low leakage inductance. The detailed design procedure for the resonant circuit at the output side of the flyback circuit with the permissible range of the parasitic component of the transformer is described on the basis of simplified analysis of resonant circuit. To verify the proposed design, computer simulation based on PSpice software and experiments for the proposed triggering circuit with a main pulse circuit was performed. For the experiment, the trigger circuit is developed with the specification of maximum 23-kV, 0.66-J/pulse output and tested with a xenon flash lamp (Heraeus P4101) driver consisting of a 1.5-kV, 36-kJ/s main pulse circuit and a 2.5-kW (500 V, 5 A) simmer circuit. The experiment is performed in both triggering without the simmer mode and combining the simmer mode. From the simulation and experimental results, it is verified that the triggering circuit can be used effectively, as it exhibits reliable ignition. [ABSTRACT FROM AUTHOR]

Repetitive high-voltage square pulses are of great importance for producing long-pulse electron beams and high-power microwaves. One of possible technologies for the generation of such pulses is a Marx generator using pulse forming network (PFN) stages, often combined with a pulse sharpening technique to reduce the rise time to a few nanoseconds (peaking stage). This paper presents an innovative design, named the “zigzag design,” for the optimization of the compactness and of the rise time of 400-kV–85-ns PFN-Marx. Thanks to this design, the 16 stages of this generator, which delivers an open circuit output voltage of 720 kV, fit in a 650-mm length. For a slightly overmatched load ($Z_{\mathrm {load}} = 100 ~\Omega$), the output voltage reaches 400 kV with a rise time as less as 5 ns. The inductance reduction associated with the innovative zigzag design, which allows this sharp rise time with no need for a peaking stage, is described. The 85-ns plateau duration of the pulse is given by the PFN construction of each stage, which is based on six ceramic capacitors (2.1 nF–45 kV) connected within a strip line. The 16 PFN stages are housed in a 360-mm diameter gas pressurized vessel. Burst mode operation for a duration of 10 s at a pulse repetition frequency of 100 Hz is reported, for a resistive load and for the electron beam diode of a X-band relativistic backward-wave oscillator (BWO). To reach further compactness, the BWO system is integrated on side of the generator vessel and a U-shaped gas pressurized line connects both systems through a compact conical vacuum insulator. [ABSTRACT FROM AUTHOR]

This paper presents a new capacitor bank topology for a pulsed power system to improve the efficiency of multistage synchronous induction coilgun. In the proposed method, a switch, such a gate turn-off thyristor, is inserted in parallel to a crowbar diode and load to generate an attractive force between the next stator and the armature. A mathematical model was developed, and finite-element method simulations were conducted to verify the proposed topology. The results show that the proposed method improves the energy efficiency and launch velocity. The improvement in energy efficiency is confirmed from the simulation results of a three-stage synchronous induction coilgun. [ABSTRACT FROM AUTHOR]

Inductive pulsed power supply (IPPS), especially superconducting pulsed power supply (PS), has been the focus of research in recent years due to its high energy density and low power requirement for the input PS. Quite a lot of fantastic work regarding two or multiple IPPS modules has been presented. But they disregard the mutual inductance between modules. This paper establishes a double-module IPPS based on two high-temperature superconducting pulsed power transformers and takes the mutual inductance between modules into consideration. The influence of the mutual inductance between two modules on three discharge modes of the system is researched. Simulations and experiments on synchronous discharge, time-delay discharge, and asynchronous discharge are carried out, respectively. The results demonstrate that taking the mutual inductance into consideration, the amplitude and the pulsewidth of the output currents are both improved a lot, especially the obtainable energy of load is improved by nearly half. For time-delay discharge, the mutual inductance makes the delay time slightly increase. However, for asynchronous discharge, the mutual inductance increases the positive maximum value of the primary current of the second module. It may exceed the critical current and lead to quench. Consequently, the mutual inductance between modules has positive impacts on synchronous discharge and time-delay discharge of the IPPS system while it brings both advantages and disadvantages to asynchronous discharge. [ABSTRACT FROM AUTHOR]

Paralleled pulse-forming units (PFUs) with different triggering delays might be a paramagnetic way for generating flat-topped current wave for electromagnetic launch. Many researchers have reported that multiple capacitive storage PFUs were implemented such current waves in laboratories. However, due to its low energy density, the applications of the capacitive pulsed-power supplies are limited. Since the inductor has advantages in energy density, the inductor pulsed-power supply becomes one of the hottest topics recently. The slow transfer of energy through capacitive hybrid meat grinder with inverse current commutation with semiconductor devices proposed by Tsinghua University has demonstrated its advantage and applicability recently. Using this kind of topology, this paper proposes the design of an inductive storage PFU with a stored energy of 100-kJ. The maximum load current reaches to 50 kA and its pulsewidth is at least 5 ms. The optimized inductive storage PFU shows superiority in contrast to the capacitive storage PFU with the same energy. This paper offers the theoretical analysis and the testing foundation for investigating the inductor pulsed-power supply with higher energy. [ABSTRACT FROM PUBLISHER]

This paper presents a novel brushless doubly fed alternator (BDFA) based on the differential mode and conducts research on its applications in a pulse capacitor charge power supply (CCPS). Since there are no brushes, the brushless doubly-fed alternator is expected to have high reliability and long service life. The excitation winding of the BDFA that is placed in the stator slots can be supplied with either dc or ac. In previous studies, regardless of the rotor configuration, the natural speed of BDFA is 60f/(p1+ p2) , i.e., based on the additive mode. To increase the alternator’s natural speed, expand the alternator’s operation as well as control range and to promote the alternator’s power density, this paper presents the differential mode, i.e., natural speed is equal to 60f/\vert p1-p2\vert . The author will introduce the detailed design method of the BDFA based on the differential mode. Utilizing the finite-element model of the alternator, we will analyze the magnetic field distribution and calculate inductance parameters of the BDFA. Subsequently, the inductance mathematic model of the BDFA will be established. We also establish the simulation model of the pulse CCPS. Finally, we will verify the feasibility of the design scheme for the BDFA through the simulation results in a pulse CCPS system. [ABSTRACT FROM PUBLISHER]

Slow transfer of energy through capacitive hybrid (STRETCH) meat grinder circuit, which was proposed by the Institute for Advanced Technology, added a capacitor into the traditional meat grinder circuit. Even though its energy density is slightly less than the corresponding pure inductance system, it can reduce the voltage across the opening switch and maintain the high multiplication factor of the opening current. The performance of the STRETCH meat grinder circuit depends on multiple parameters. The inductance ratio ( n=L1 / L2) and the capacitance (C) are the two vital factors, which have a crucial influence on the system performance, such as the voltage over the opening switch ( V_{\rm Sopm}) , the current multiplication factor ( m$ ), and the ratio of the maximum capacitive energy over the total inductive energy ( $\eta )$ . Thorough studies have been carried out in this paper on the relationship between the above two factors and the three performance criteria. This paper also discusses and analyzes the chosen of the key parameters ( $n$ and $C$ ) for a single-stage STRETCH meat grinder with 2-mH total inductance, which is made up of two serial coils with 0.95 coupling factor. The opening current of the main switch is 1 kA, which constitutes a 1-kJ inductive pulsed-power supply. It fully takes the advantage of the STRETCH meat grinder topology, intensifies the study of the inductive pulsed-power supply with higher energies, and is easy to be utilized for practical application. [ABSTRACT FROM PUBLISHER]

In this paper, a new structure of coilgun with stepped coil winding was designed. The performance of this structure was investigated and compared to the conventional coilgun with uniform diameter stator coil (UDSC) winding. It can be seen from the results that the trigger position of this new structure moves forward with respect to the conventional coilgun. In order to compare the results, the inductance of the two coils is set to the same. If the initial voltage of the capacitor is lower, as the armature at the optimum trigger position, the muzzle velocity of armature in the conventional UDSC coilgun is relatively larger. Conversely, if the initial voltage of the capacitor is higher, the muzzle velocity of armature in the new structure coilgun is relatively larger. According to the simulation results with the increase of voltage, the difference is more and more obvious. Through the single-stage preliminary experiment in our laboratory, the results were in good agreement with the simulation results. And the trigger position is more forward, so the interaction time between the armature and the coil will be longer. Besides, the coil with stepped structure will increase the efficiency of the coilgun when the voltage level is higher. [ABSTRACT FROM AUTHOR]

The Alfvén eigenmodes (AEs) excitation system has been designed and installed on the J-TEXT tokamak. The system consists of a series resonant power supply and an excitation antenna. Under the typical operating conditions of the J-TEXT, the excitation frequency is thought to be in the range of 200–700 kHz. In order to match the AEs frequency, the external excitation system needs to scan its frequency automatically in experiments. In the implementation process, the whole frequency band is divided into several segments. For each one of them, the resonant circuit matches different capacitors. Specifically, the resonant capacitor is arranged in the form of a fixed capacitor in parallel with a variable capacitor. In the last campaign, a 2.3-nF fixed capacitor and a 1-nF variable capacitor are picked up, so that the resonant capacitance could change from 2.3 to 3.3 nF. In addition, the matching units were applied to optimize the antenna currents. Finally, the formal plasma discharge experiments have been carried out on the J-TEXT. The results show that the excitation frequency can be changed from 445 to 510 kHz in 350 ms, and the output current is able to reach 50 A. This paper is focused on the design of the excitation system, particularly the strategy of frequency scanning. [ABSTRACT FROM AUTHOR]

Multipole field electromagnetic launcher (MFEL) is a new type of coilgun that can produce larger radial magnetic field compared to the axial magnetic field, the axial acceleration force of coilgun mainly come from radial magnetic field. Because of the similarity of the magnetic fields between inner and outer regions of MFEL, this paper proposed a double-armature MFEL. One armature coaxial with the drive coil placed inside of MFEL; the other armature coaxial with the drive coil placed outside of MFEL. A single-stage double-armature MFEL was studied by simulation and experimental methods. The simulation results indicated that the muzzle velocity of the double-armature launch is similar to that of the single-armature launch, and the efficiency of double-armature MFEL is obviously larger than that of single armature. To verify the conceptual feasibility, a small-size single-stage double-armature capacitor-driven MFEL was built and tested. The inner small armature weighs 63.13 g, the outer big armature weighs 88.38 g. The experimental results on single-armature launch show good consistency with the simulation results, but there is a little gap between the experimental results on double-armature launch and the simulation results. The causes of the existing differences are considered to be mainly from the consistency difference between the six driving coils and the mutual influence between the inner and outer armatures. [ABSTRACT FROM PUBLISHER]

The major strengths of inductors in energy density and power density make an inductive pulsed power supply (IPPS) a promising option for pulsed power supplies in an electromagnetic launch system. Among the circuits for an IPPS, the capacitor-aided meat grinder circuits constitute an important branch. An analytical method for the working processes of these circuits is proposed in this paper. The core of this method is the decoupling of a high-order circuit into the superposition of a resistor–inductor first-order equivalent subcircuit and a resistor–inductor–capacitor second-order equivalent subcircuit. The validity and accuracy of this method have been verified through comparison with a numerical simulation. The results show that this method possesses both satisfactory accuracy and excellent computational speed. With the same circuit parameters and time step, the time cost of this method is three orders of magnitudes lower than the time cost of a numerical simulation. Moreover, this method contributes to more intuitive understanding and more essential insight into the working principles of the capacitor-aided meat grinder circuits. [ABSTRACT FROM PUBLISHER]

The amount of stored energy is an important issue in the low-droop and high-precision pulse generation. Pulse forming network (PFN) simulating an open-ended transmission line seems to be useful due to its minimum stored energy. The drawbacks of the PFN include low-output pulse quality and constant pulsewidth, which limit their applications. Another limitation of generating rectangular pulses using PFN is that half of the charged voltage appears in the output when delivering the entire stored energy to the matched load. This paper proposes a structure of PFN-based pulse generator that overcomes the above-mentioned limitations. For continuous pulsewidth adjustment, a lossless scheme is presented. By increasing the ratio of the load magnitude to the characteristic impedance, the amplitude of the output pulse voltage would be approximately equal to that of the charged voltage. Therefore, the semiconductor switches can be utilized in the PFN pulse generator easily. In addition, the pulse quality is enhanced and faster rising time is obtained in comparison with the conventional PFNs. In this proposal, the stored energy quantity is limited to three times the energy needed for the output pulse in the case of RL=10Z0 . To verify the proposed structure, a prototype is simulated using PSPICE software, and the experimental results are presented. [ABSTRACT FROM AUTHOR]

The slow transfer of energy through capacitive hybrid (STRETCH) meat grinder circuit is a widely used topology in inductive pulse power supply. Therefore, it is important to understand the relationship between the STRETCH meat grinder performances and the inductor parameters when improving the system performance and designing the inductor. From the perspective of inductor designing, this paper uses four indicators to present the STRETCH meat grinder performances, i.e., the charging current, the current amplification, the inductor energy density, and the discharge efficiency, and uses two indicators to present the inductor parameters, i.e., the total inductance and the ratio of the inductance L1 to L2 . First, the meanings of the indicators are explained or defined. Second, simulations and experiments are carried out, respectively, to analyze the trends of the four performance indicators along with the changes of two parameters indicators. Finally, both simulation and experiment results show that the increase of the total inductance leads to the decrease of the charging current and the discharge efficiency; moreover, the increase of the ratio of the inductor L1 to L2 leads to the increase of the current amplification and the discharge efficiency, but causes the decrease of the inductor energy density. [ABSTRACT FROM AUTHOR]

The field-reversed configuration heating experiment (FRCHX) was designed to form closed-field-line magnetized target plasmas for magnetoinertial fusion and other high energy density plasma research. These plasmas are in a field-reversed configuration and are formed via a reversed-field theta pinch on an already magnetized background plasma. To extend the duration and temporal uniformity of the pinch, the capacitor bank driving the reversed-field discharge is crowbarred near the current peak. Four parallel rail-gap switches are used on the FRCHX for this application to ensure a low-inductance crowbar discharge path and to accommodate the large magnitude of the discharge current (often greater than 1 MA). Historically, parallel operation of spark gap switches in a crowbarring arrangement has often proved to be difficult due to the very low voltage present on the bank and across the switches at the time of peak current. In a low-inductance design, triggering can be further complicated by the rapid collapse of what little voltage there is across the switches as soon as the first spark gap begins conduction. This paper reports on the efforts that were made to develop a low-inductance crowbar switch for the FRCHX and to ultimately enable successful triggering and operation of the four parallel rail-gap switches used in the crowbar. The design of the low-inductance parallel switch assembly is presented first, followed by a description of the triggering scheme employed to ensure conduction of all four switches. [ABSTRACT FROM AUTHOR]

This paper details the experimental evaluation and simulation of a 4-kV n-type gate turn-OFF thyristor (GTO) designed for pulsed power applications. The primary criteria of evaluation are rate of current rise ( dI/dt ), turn-ON delay time ( T_{D}) , and resistance of the device during turn-ON transients [ R_{\mathrm{\scriptscriptstyle ON}}(t)$ ]. The device under test (DuT) is an n-type asymmetric-blocking GTO manufactured by Silicon Power (Part No. 14N40A10) with a rated dc blocking voltage of 4 kV. A test circuit was specifically designed to minimize stray inductance in order to capitalize on the dI/dt$ capabilities of the DuT. Experimental data collected from resistance measurements are used to develop a single-switch approximate model for use in simulation. The results of dI/dt$ experiments provide a profile of DuT dI/dt$ operation beyond rated values; specifically dI/dt were readily achieved. The turn-ON delay time of the DuT is also characterized and determined to be $\sim 225$ ns on average. [ABSTRACT FROM AUTHOR]

The superconducting inductive pulsed-power supply (SPPS) circuit consists of a high-temperature superconducting pulsed-power transformer (HTSPPT) and an auxiliary capacitor. The electrical losses and the power of the primary source can be cut down with the superconducting inductive energy storage. Although its energy density is slightly less than a purely superconducting inductive system, it can reduce the maximum voltage of the opening switch by the capacitor and achieve a high degree of current amplification factor. However, during the discharge process, the magnetic leakage flux energy stored in the primary of the HTSPPT requires the capacitor to have a certain capacity. The higher the ratio of the capacitive stored energy over the total inductive stored energy, the more the dominant position of inductive energy storage reduces. The current amplification factor ( \gamma ), the maximum voltage of the opening switch ( V_{S\max } ), and the ratio of capacitive stored energy ( \eta ) are the three main properties of the SPPS circuit, which depends on several intertwined critical parameters, such as the inductance ratio n = L2 /( L2+LL ) and the capacitance ( $C_{{\mathbf {1}}}$ ). This paper studies the influence of the critical parameters on the main circuit performance with a 1-kJ SPPS system. The detailed selection method of the critical parameters for the specific system is also discussed with a coupling coefficient of 0.95. Such a system is easy to be utilized for the basic experimental study of a small railgun. [ABSTRACT FROM PUBLISHER]

This paper describes a compact high storage density inductive–capacitive storage module. The module is based on high-power opening switches using inverse current commutation with semiconductor devices commutation principle and a high storage density Brooks inductor. These opening switches, being able to switch-OFF pulse currents up to 14.5 kA by the counter-current subcircuit, make use of the general property of a standard high-power thyristors impedance transition from closing state to blocking state. The experimental results show that with the primary capacitor and counter-current commutation subcircuit charged voltage 3 and 2.5 kV, respectively, the charged current of the Brooks-type inductor is about 14.5 kA, with a charged time of about 4.5 ms. The output peak current of the inductive storage module is about 21 kA. The total stored energy is about 54.9 kJ while the energy density of the inductor is approximately 6.69 MJ/ \textm^3 , which is not including the primary storage and commutation unit. [ABSTRACT FROM PUBLISHER]

In this paper, a new approach for modeling electromagnetic railguns is proposed. The model’s simplicity makes it suitable for sensitive analysis and optimization procedures. For validation, the railgun is simulated by a 3-D finite-element method (FEM) using Maxwell software and the results are compared with existing experimental data. Circuit model simulation results verified the accuracy of the model as they are very close to the experimental ones. As multistage railgun is one of the greatest improvements in railgun expansions, a successful attempt is made for the new circuit model to include this, as evidenced by comparing the results of multistage railgun model with those of the FEM. [ABSTRACT FROM PUBLISHER]

By applying the principle of inverse current commutation with semiconductor (ICCOS) devices in a slow transfer of energy through capacitive hybrid (STRETCH) meat grinder system, a novel circuit topology called STRETCH meat grinder with ICCOS was proposed by the Tsinghua University in 2013. It can not only raise the amplitude of the opening current, but also reduce the cost of the STRETCH meat grinder circuit obviously by replacing the integrated gate-commutated thyristor (IGCT) with thyristor. This paper discusses the overall design, system implementation, and testing results of a STRETCH meat grinder with ICCOS system with roughly 1-kJ inductive energy. The load is a spiral coil with 1.4- \textm\Omega resistance and 1.4- \mu \textH inductance. With closed-loop control strategy, the system detects the charging current of the inductors. When it reaches the designated value, the triggering signal for ICCOS is delivered and after the predefined delay time, the triggering signal for discharging the voltage on the pulse-forming capacitor is delivered. The current of the inductors and the load are measured by Rogowski coils. The opening current is 1 kA and the maximum load current is close to 4 kA. All the voltages on the switches are lower than 1 kV. The experimental results are consistent with the simulated ones, which verified the correctness of the theoretical analysis and proved the applicability of the STRETCH meat grinder with ICCOS for larger energy level. [ABSTRACT FROM PUBLISHER]

The Precision High Energy-Density Liner Implosion Experiment (PHELIX) is a pulsed power driver capable of delivering multimegampere currents to cylindrical loads. The PHELIX hardware includes novel design features to provide a high-energy conversion efficiency of approximately 10-MA output current per megajoule of stored energy. This is achieved by a rail-gap switched low-inductance Marx design (resistively damped) driving a multifilar air-core pulse transformer. The Marx output cables form the toroidal transformer that is an integral part of the disc line and removable load cassette assembly. The transformer and disc line uses conformal insulation methods and does not require replacement; after each shot, the transformer is completely reusable. Load cassettes can be easily exchanged to facilitate experimental variation. PHELIX is self-contained within its own transport container and Faraday cage that can be moved from the maintenance building to the Los Alamos Neutron Science Center 800-MeV proton accelerator facility to perform multipulse proton radiography. This paper details the electrical and mechanical design of the Marx and multifilar transformer assemblies as well as presenting the operational performance achieved to date. [ABSTRACT FROM PUBLISHER]