Search

This paper presents the design and construction of a sample of Marx pulsed generator based on boost converter (BC) pulse-forming networks (BCPFNs). BCPFN is used instead of the conventional Marx floors for constructing this pulsed generator. BCPFN is carried out by connecting inductors and capacitors in series and parallel modes, respectively, by using solid-state switches, and during this procedure the pulsed generator converts to BC temporarily and increases the voltage of capacitors uniformly to a considerable value. This technique causes an increase in the discharging voltage level to the load that is many times more than its dc voltage source by charging the capacitors to a greater level. In order to take advantage of the benefits of Marx generator and PFN, this paper suggests a new circuit with the minimum number of switches. It means, to compose BCPFN and Marx, we have tried to design the circuit with fewer switches and instead of it we have achieved our desired performance with changing the operating mode in the states of BC, PFN, BCPFN, and BCPFN Marx. The results are simulated with MATLAB software. At the end, the experimental results of the construction of the above-mentioned system at low-power levels are presented, and the topology’s accuracy is proved by comparing them to the results of simulation. [ABSTRACT FROM AUTHOR]

This paper presents the effect of stray capacitances in bipolar (negative and/or positive) pulses generated by the two different topologies of the solid-state Marx modulators. According to the analysis, the stray capacitances influence the energy transfer from the Marx modulator capacitors to the load affecting the bipolar (negative and/or positive) pulse rise time. This paper deals with the structure design to reduce the influence of the stray capacitance and to improve the pulse rise time of these bipolar solid-state Marx modulators. A four-stage laboratory prototype of the two topologies has been assembled using 1200-V insulated gate bipolar transistors and diodes, operating with 1000-V dc input voltage and 1-kHz frequency, producing 4-kV bipolar pulses, with 5- \mu \texts pulse duration and 120-ns rise time, into a resistive load. [ABSTRACT FROM PUBLISHER]

This paper addresses the design of a solid-state bipolar pulsed-power modulator based on a series of stacked power cells that realize a simple and robust structure. Each cell is charged in parallel by an LCC resonant converter independently of the discharging loop. A passive cell-balancing design is implemented. The power cell using insulated gate bipolar transistors (IGBTs) can operate in bypass mode without an additional component, and the circuit operation was analyzed. A simple gate driving method, which provides synchronized gate signals without an extra power source of each gate driver using two control loops and isolation transformers, is implemented for the proposed bipolar pulsed-power modulator based on stacked cells. Moreover, an unexpected gate turn-on problem was solved by an additional off signal. To validate the proposed structure and the gate driving scheme, a three-cell, 1.2-kV, 110-A, 1.5- to 4- $\mu \text{s}$ , 3-kHz laboratory experimental prototype test was conducted. The results proved the reliability of the proposed solid-state bipolar pulsed-power modulator. [ABSTRACT FROM AUTHOR]

Marx generator using all-solid-state devices has been studied for many years. Higher parameters are always the demand for new applications. Traditional all-solid-state Marx generator can output high voltage due to its series topology, but the current is always limited by the switch. In this paper, a stage-stage paralleled topology of Marx generator for high current has been proposed. Topology structure and driving mode comparison for current balance have been analyzed. The paralleled driving mode for the current balance and the shaping waveform has been proposed. For experiment, a four-stage-four-paralleled Marx generator with metal–oxide–semiconductor field-effect transistors (MOSFETs) has been constructed with output pulses 2.2 kV, 730 A (depending on the load), rise time of 31 ns, fall time of 56 ns, and adjustable pulsewidth from 400 to 800 ns. [ABSTRACT FROM AUTHOR]

In this paper, a modular topology is presented for generating high-voltage pulsed power. The proposed structure consists of Marx-type modules, which are based on the switched-capacitor (SC) concept. This module receives an input voltage and, depending on the requirement of the user, produces an output voltage either equal to the input or twice as much as the input voltage, which shows the flexibility of our model. The capability of the module to produce a doubled output makes it appropriate for applications with low input voltage sources. Also, the topology has the capability of generating combined wide and narrow pulses. The topology was simulated in MATLAB Simulink and a laboratory setup was built to test its operation. The results validate the theoretical basis of the structure. [ABSTRACT FROM AUTHOR]

In this paper, a high-voltage unipolar pulse power generator is introduced for electroporation applications. Operating principle of the proposed structure is based on the buck–boost (BB) converter. The generator is comprised of parallel modules connected to the converter through an SCR and is supplied by a low-voltage dc source. Each module consists of an insulated gate bipolar transistor (IGBT), two diodes, and a capacitor. In fact, the proposed topology is a combination of the Marx generator and BB (MG-BB) converter. In comparison with other modular MG-BB structures, the proposed topology achieves interesting advantages including simpler structure, reduction of IGBTs voltage rating, and reducing number of components (inductors and switches). In order to clarify the features of the proposed structure, it has been compared with other unipolar MGs considering different aspects including the number of circuit components, number of required input supplies, amplitude of the output pulse, and the maximum voltage across switches and diodes. To validate the effectiveness of the structure, simulation and experimental results are presented. The results confirm that the proposed topology is capable of generating unipolar pulses with desirable amplitude and repetition frequency using a low-voltage dc supply. [ABSTRACT FROM AUTHOR]

Recently, inductive energy storage systems have attracted interests due to high energy densities. The high-temperature superconducting pulsed-power supply (HTSPPS) is one inductive PS topology for electromagnetic launching system. The topology can achieve a high amplitude load current and cut down the electrical losses due to the zero resistance characteristic of superconducting inductors. However, in this topology, the integrated gated commuted thyristor is used as a switch and cannot withstand high current, which limits the expansion of the system. Besides, it has significant current amplification ability as a single unit, but one module cannot provide sufficient amplitude and appropriate pulsewidth for the load current of the electromagnetic launching. In this paper, by applying the principle of inverse current commutation with semiconductor devices (ICCOS) in the HTSPPS, a novel circuit topology called HTSPPS with ICCOS is presented. This topology is analyzed and the multiple modules system is established. Simulation results show that the HTSPPS with ICCOS exceeds the current limitations of the original one and ensures the reliable cutting off of the main switch. It has potential applications in the future of high-energy systems while reducing the cost greatly. By asynchronous cooperative triggered discharge of the multiple HTSPPS with ICCOS modules in parallel, the appropriate amplitude and flat shape current of the load can be achieved through the careful design of the trigger time. [ABSTRACT FROM AUTHOR]

One of the critical components of high energy density pulsed power systems used to generate short high-voltage and high-power impulses is gas-filled plasma closing switch (PCS). In recent years, significant research efforts have been aimed at finding environmentally friendly gases which can be used in the PCSs, and several gases including dry air, nitrogen, carbon dioxide, argon, and their mixtures have been considered as potentially suitable working fluids in such switches. However, the lack of knowledge of the breakdown characteristics of complex switching topologies filled with these gases limits their practical applications. Therefore, further investigation of the breakdown performance of PCSs is required, in order to establish their applicability for practical use in high-voltage pulsed power systems. This paper reports on the investigation of the breakdown characteristics of a triggered PCS topology with corona discharge electrodes. The self-breakdown voltage of the switch, variation in the self-breakdown voltage, time to breakdown, and jitter have been obtained for the switch filled with “zero grade” air, N2, CO2, and an Ar/O2 mixture up to a pressure of 10 bar (abs). It was shown that the switch can provide a stable breakdown performance with jitter as low as ~1 ns. [ABSTRACT FROM AUTHOR]

Paralleled pulse-forming units (PFUs) with different triggering delays might be a paramagnetic way for generating flat-topped current wave for electromagnetic launch. Many researchers have reported that multiple capacitive storage PFUs were implemented such current waves in laboratories. However, due to its low energy density, the applications of the capacitive pulsed-power supplies are limited. Since the inductor has advantages in energy density, the inductor pulsed-power supply becomes one of the hottest topics recently. The slow transfer of energy through capacitive hybrid meat grinder with inverse current commutation with semiconductor devices proposed by Tsinghua University has demonstrated its advantage and applicability recently. Using this kind of topology, this paper proposes the design of an inductive storage PFU with a stored energy of 100-kJ. The maximum load current reaches to 50 kA and its pulsewidth is at least 5 ms. The optimized inductive storage PFU shows superiority in contrast to the capacitive storage PFU with the same energy. This paper offers the theoretical analysis and the testing foundation for investigating the inductor pulsed-power supply with higher energy. [ABSTRACT FROM PUBLISHER]

Slow transfer of energy through capacitive hybrid (STRETCH) meat grinder circuit, which was proposed by the Institute for Advanced Technology, added a capacitor into the traditional meat grinder circuit. Even though its energy density is slightly less than the corresponding pure inductance system, it can reduce the voltage across the opening switch and maintain the high multiplication factor of the opening current. The performance of the STRETCH meat grinder circuit depends on multiple parameters. The inductance ratio ( n=L1 / L2) and the capacitance (C) are the two vital factors, which have a crucial influence on the system performance, such as the voltage over the opening switch ( V_{\rm Sopm}) , the current multiplication factor ( m$ ), and the ratio of the maximum capacitive energy over the total inductive energy ( $\eta )$ . Thorough studies have been carried out in this paper on the relationship between the above two factors and the three performance criteria. This paper also discusses and analyzes the chosen of the key parameters ( $n$ and $C$ ) for a single-stage STRETCH meat grinder with 2-mH total inductance, which is made up of two serial coils with 0.95 coupling factor. The opening current of the main switch is 1 kA, which constitutes a 1-kJ inductive pulsed-power supply. It fully takes the advantage of the STRETCH meat grinder topology, intensifies the study of the inductive pulsed-power supply with higher energies, and is easy to be utilized for practical application. [ABSTRACT FROM PUBLISHER]

The STRETCH meat grinder is one typical inductive pulsed-power supply topology for electromagnetic launch system. It has remarkable current amplification ability as a single unit, but one module cannot provide enough amplitude and width for the load current of the railgun launching. This paper discusses the effects of different triggering delays on the load current with two STRETCH meat grinder modules. To reduce the magnetic field coupling between the two modules, the two main switches are opened simultaneously. To make the load current waveform with no notch, the thyristor of the first module is triggered when its pulse-forming capacitor is fully reversely charged. For the thyristor of the second module, we consider several time points of triggering delay. Because of the practical constraint for the maximum rail current that ensures no rail erosion, the rectangular waveform is the most appropriate load current waveform. Therefore, the comparing criterion can be defined as the ratio of the load current waveform area and its maximum rectangle area at different current levels. Higher ratio means that the current is more like a rectangular wave and is better accordingly. Based on the above criterion and extensive simulation research, we found that the best delay time is the moment when the capacitor is reversely charging the inductor completely. This paper and the result are of great theoretical significance for the further study on the collaborative triggering of multiple STRETCH meat grinder modules. [ABSTRACT FROM PUBLISHER]

High-voltage (HV) pulses are used in pulsed electric field (PEF) applications to provide an effective electroporation process, a process in which harmful microorganisms are disinfected when subjected to a PEF. Depending on the PEF application, different HV pulse specifications are required such as the pulse-waveform shape, the voltage magnitude, the pulse duration, and the pulse repetition rate. In this paper, a generic pulse-waveform generator (GPG) is proposed, and the GPG topology is based on half-bridge modular multilevel converter (HB-MMC) cells. The GPG topology is formed of four identical arms of series-connected HB-MMC cells forming an H-bridge. Unlike the conventional HB-MMC-based converters in HVdc transmission, the GPG load power flow is not continuous which leads to smaller size cell capacitors utilization; hence, smaller footprint of the GPG is achieved. The GPG topology flexibility allows the controller software to generate a basic multilevel waveform which can be manipulated to generate the commonly used PEF pulse waveforms. Therefore, the proposed topology offers modularity, redundancy, and scalability. The viability of the proposed GPG converter is validated by MATLAB/Simulink simulation and experimentation. [ABSTRACT FROM PUBLISHER]

This paper describes the design, implementation, and comparison of high-voltage capacitor chargers for a solid-state pulsed power modulator (SSPPM). The three different converter topologies are a series resonant converter operating at a discontinuous conduction mode with switching frequency control (SRC_DCM_SFC), a series resonant converter operating at a continuous conduction mode with phase shifted pulse width modulation control (SRC_CCM_PSPWMC), and a series–parallel resonant converter operating at the CCM with SFC (SPRC_CCM_SFC). On the basis of these converter topologies, 10\-kW\rm{average} high-voltage capacitor chargers are designed for the three types of SSPPMs, which have the following maximum output specifications: 1) SRC_DCM_SFC: 60 kV, 300 A, 3 kpps, and 50 \mus; 2) SRC_CCM_PSPWMC: 10 kV, 50 A, 50 kpps, and 10 \mus; and 3) SPRC_CCM_SFC: 40 kV, 150 A, 7 kpps, and 10 \mus. Although the pulse output specifications are different, it is worth comparing the resonant inverter topologies and the control methods from the viewpoint of the losses, control characteristics, and merits and demerits of the high-voltage capacitor chargers. From the analysis and investigation of the three resonant inverters, the design procedure, including the determination of the resonant tank parameters, is provided, which considers the design of the high-voltage capacitor charger. PSPICE simulation is used to elucidate the effects of the resonant tank structure and its parameters, and the resonant current waveform and losses of the Insulated Gate Bipolar Transistor are compared. Finally, experiments for each charger are performed under various load conditions, and the comparison results of the three capacitor chargers, including the conduction and switching losses, control characteristics, and overall efficiency, are discussed in this paper. [ABSTRACT FROM AUTHOR]

With inherent strengths in energy density and power density, the inductive pulsed power supplies (IPPS) have become an attractive option for the power supplies in electromagnetic launch systems. The meat grinder circuits, including the slow transfer of energy through capacitive hybrid (STRETCH) meat grinder circuit, the STRETCH meat grinder with inverse current commutation with semiconductor devices circuit, and the meat grinder with self-charged capacitor and thyristors circuit, constitute one major branch among the IPPS circuits. This paper summarizes the fundamental research work and contributions of the meat grinder circuits from the perspectives of circuit improvements, performance analysis, inductor design, module collaboration, and efficiency promotion. The future directions of single IPPS module are higher energy level, larger energy density, and higher efficiency. [ABSTRACT FROM PUBLISHER]

This paper presents a novel technique for the voltage droop compensation of long pulses in solid-state bipolar high-voltage Marx generators. Considering the modularity of Marx generators the compensation consists in adding one extra stage to perform as a pulsewidth modulation circuit. This stage voltage is added to the output positive or negative pulses, and an output LfCf filter is included to smooth the voltage pulse waveform. A five-stage laboratory prototype of this circuit has been assembled using 1200-V Insulated Gate Bipolar Transistors and diodes with 1000-V dc input voltage. The circuit was operated at 50-Hz bipolar pulse rate, giving 4-kV bipolar pulses, into a resistive load, with 100- \mu \texts pulsewidth and 9.5-ms relaxation time. The circuit was able to compensate 10% of bipolar pulse voltage droop. [ABSTRACT FROM PUBLISHER]

This paper presents a power electronics converter to generate bipolar high-voltage pulses using low-voltage dc source. Converter is designed based on charging of different capacitors by a predetermined switching pattern and their discharging on the load for pulsed power applications. Low number of power electronics devices and bulky transformer elimination are main advantages of the proposed converter. According to new findings, bipolar high-voltage pulses may lead to higher efficiency in many applications, such as food sterilization industry. The proposed pulse generator generates bipolar controllable pulses with a modular circuit structure based on a capacitor-switched network. Experimental results are presented to verify the analysis. [ABSTRACT FROM AUTHOR]

A bipolar pulse has been proved to be more advanced in the treatment of tumor because of the elimination of muscle contractions and the effect for ablating nonuniform tissue. In this paper, a new type of modular bipolar pulsed-power generator based on Marx generator with double power charging is proposed. The concept of this generator is charging the two series of capacitors in parallel by two power sources, respectively, and then connecting the capacitors in series through solid-state switches with different control strategies. Utilizing a number of fast solid-state switches, the capacitors can be connected in series with different polarities, so that a positive or negative polarity pulse will be delivered to the load. The simulated models of this generator have been investigated in a PSPICE platform, and a laboratory prototype has been implemented in a laboratory. The simulation and test results verify the operation of the proposed topology in different switching modes. The development of this pulse generator can provide the hardware foundation for the research on biological effect without muscle contraction when the tumors are applied with bipolar pulse electric field. [ABSTRACT FROM AUTHOR]

This paper describes a modular solid-state switching cell derived from the Marx generator concept to be used in topologies for generating multilevel unipolar and bipolar high-voltage (HV) pulses into resistive loads. The switching modular cell comprises two ON/OFF semiconductors, a diode, and a capacitor. This cell can be stacked, being the capacitors charged in series and their voltages balanced in parallel. To balance each capacitor voltage without needing any parameter measurement, a vector decision diode algorithm is used in each cell to drive the two switches. Simulation and experimental results, for generating multilevel unipolar and bipolar HV pulses into resistive loads are presented. [ABSTRACT FROM PUBLISHER]

Utilization of power electronics converters in pulsed power applications introduced a new series of reliable, long life, and cost-effective pulse generators. However, these converters suffer from the limited power ratings of semiconductor switches, which necessitate introduction of a new family of modular topologies. This paper proposes a modular power electronics converter based on voltage multiplier as a high voltage pulsed power generator. This modular circuit is able to generate flexible high output voltage from low input voltage sources. Circuit topology and operational principles of proposed topology are verified via experimental and simulation results as well as theoretical analysis. [ABSTRACT FROM PUBLISHER]

Inductive pulse power supplies are of interest because their energy densities are one order of magnitude higher than those of capacitive power supplies, based on the same power-output capacity. The Institute of Advanced Technology puts forward an inductive pulse power topology called the slow transfer of energy through capacitive hybrid (STRETCH) meat grinder. In this topology, an active switch is used to cut off the charging current. Limited by the current turning off ability of integrated gated commuted thyristor, it may encounter difficulties in extending to higher-energy systems. Other than that, the cost of the system is very high. In this paper, the principle of the STRETCH meat grinder is presented. Then, the STRETCH meat grinder with inverse current commutation with semiconductor devices (ICCOS), which is proposed by the Institute of Saint Louis, is presented. The process of ICCOS in the STRETCH meat grinder is illustrated in detail. Finally, simulations are made based on Simplorer 8 to explain how ICCOS works clearly. A preliminary discussion of how to design ICCOS is also presented. We conclude that the STRETCH meat grinder with ICCOS removes the limitations of the original one and has potential applications for high-energy systems in future and can cut down the cost greatly. [ABSTRACT FROM PUBLISHER]

Modern pulsed power technology has its roots in the late 1950s and early 1960s, and it was driven overwhelmingly by applications in national defense carried out by several countries, especially the U.S., U.K., Russia, and China. The following decades, particularly the early 1990s, witnessed an increased interest in compact systems with pulse repetition rate that could be used in nondefense applications such as treatment of material surfaces by plasma and beam interactions, treatment of pollutants, food sterilization, medical applications, etc. This spawned a new generation of pulsed power components (solid-state switches) that led to completely solid-state modulators. This paper describes how the pulsed power technology used originally in beam sources and cathodic arcs has converged to produce power sources for plasma-based ion implantation (PBII) and related technologies. The present state of the art is reviewed, and prospects for future advances are described, especially for PBII. [ABSTRACT FROM AUTHOR]

A new pulsed-power generator based on a Marx generator (MG) is proposed in this paper with a reduced number of semiconductor components and with a more efficient load-supplying process. The main idea is to charge two groups of capacitors in parallel through an inductor and take advantage of the resonant phenomenon in charging each capacitor up to twice as the input-voltage level. In each resonant half-cycle, one of those capacitor groups is charged; eventually, the charged capacitors will be connected in series, and the summation of the capacitor voltages are appeared at the output of a pulsed-power converter. This topology can be considered as a modified MG, which works based on the resonant concept. The simulated models of this converter have been investigated in a MATLAB/Simulink platform, and a laboratory prototype has been implemented in a laboratory. The simulation and test results verify the operation of the proposed topology in different switching modes. [ABSTRACT FROM AUTHOR]

This paper presents a high-voltage pulsed-power system based on low-voltage switch–capacitor units that are connected to a current source for several applications such as plasma systems. A modified positive buck–boost converter topology is used to utilize the current source concept, and a series of low-voltage switch–capacitor units is connected to the current source in order to provide a high voltage with a high voltage stress (dv/dt) as demanded by the loads. This pulsed-power converter is flexible in terms of energy control because the stored energy in the current source can be adjusted by changing the current magnitude to significantly improve the efficiency of various systems with different requirements. The output-voltage magnitude and stress (dv/dt) can be controlled by a proper selection of components and control algorithm to turn on and off the switching devices. [ABSTRACT FROM PUBLISHER]