Search

Photovoltaic (PV) strings consisting of multiple panels suffer from partial shading or characteristic mismatch issues, such as a significant reduction in power yield. Various kinds of differential power processing (DPP) converters have been developed to prevent the negative impacts of substring-level partial shading. For panel-level applications, however, conventional DPP converters face a variety of challenges, such as impaired extendibility and increased voltage stress of circuit elements. This paper proposes a switched capacitor converter (SCC)-based modular DPP architecture. Modules, each containing series-connected panels with a panel-level DPP converter, are connected through a switchless module-level DPP converter, and PV panel characteristics are unified at module- and panel-levels. The number of panels in each module is fixed, while the number of modules can be arbitrarily extended without redesigning DPP converters, hence offering good modularity. In addition, since voltage stresses of capacitors in the proposed architecture can be reduced lower than half the module voltages, the proposed DPP system realizes all-ceramic-capacitor SCC circuit by properly determining the module voltages. A prototype for eight panels, which were grouped into two modules, was built, and laboratory and field tests were performed. The experimental results demonstrated the enhanced power yield from the partially shaded PV string. [ABSTRACT FROM AUTHOR]

Finite control set model predictive control (FCS-MPC) calculates torque and flux tracking errors via a cost function that is used for selecting the optimal vector. Compared with field oriented control, FCS-MPC has the merit of a faster dynamic performance because it eliminates both pulsewidth modulation and inner proportion-integration controllers. However, the weighting factor for modifying torque and flux terms must be tuned in accordance with varying operating conditions; this is an area in which further research is needed. In this paper, a parallel predictive torque control (PPTC) with predefined constraints is proposed as a solution for this problem. The PPTC method optimizes torque and flux terms simultaneously, and switching-state candidates are then selected in an adaptive mechanism. The key feature is that torque and flux tracking errors are constrained within the initial boundaries. The proposed PPTC is compared with the state-of-the-art predictive torque control (PTC) method. Both simulation and experimental results confirm that the proposed method, which has no weighting factor, achieves an even better dynamic performance and robustness than the conventional PTC. [ABSTRACT FROM AUTHOR]

Nine-switch converter (NSC) has been presented as a dual-output converter with common frequency (CF) or different frequency (DF) operation modes. This paper proposes a novel space-vector modulation (SVM) method for the NSC that supports both the CF and DF modes. This method is based on the simplification of the space-vector diagram of NSC into that of six-switch converter, and the SVM method for NSC can be done like conventional SSC. The proposed voltage vector selection method without using common logical xor operation and the calculation method for dwelling times of voltage vectors are described in detail. In addition, the modulation indices for two ac terminals of NSC have been analyzed deeply, and the derived fitting equations can guide engineering application. The performance of the proposed SVM is verified by the simulation and experimental results, and the low total harmonic distortions and harmonic components for phase currents prove the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

This paper employs a single-phase-shift modulated dual-active-bridge converter (DABC), and establishes a small-signal model, which involves its voltage transformation ratio. Then, through a voltage transformation ratio feedback loop, which is feedforward compensated by the port voltages and currents, closed-loop control of the transformation ratio of the DABC is realized. The proposed controller can make the DABC operate in constant transformation ratio mode, and act as an ideal dc transformer in an active dc distribution network. Based on the bidirectional voltage support capability of the proposed dc transformer, the different buses of an active dc distribution network can mutually provide voltage support for each other. Besides, the proposed dc transformer can realize the normalized decentralized power coordination between the energy storage systems at different buses of the active dc distribution network. The feasibility of the proposed dc transformer is verified by several hardware-in-loop tests. [ABSTRACT FROM AUTHOR]

This paper proposes the design of gray wolf optimizer (GWO) algorithm-based fractional order proportional integral (FOPI) controller for power factor correction (PFC) using interleaved dc–dc single ended primary inductance converter converter with improved performance characteristics such as speed, accuracy, and stability. The detailed analysis and modeling of the proposed converter are presented. The optimal parameters of FOPI controller are obtained using GWO algorithm to improve the speed of response of the system. FOPI controller provides better performance in terms of robustness and stability since it has one more adjustable parameter than the conventional proportional integral (PI) controller. The cascade control strategy is implemented for the proposed converter with GWO-based FOPI controller as inner current and outer voltage controllers for PFC and load voltage regulation. The performance characteristics of the proposed system are analyzed and compared with conventional and other optimization techniques using MATLAB/Simulink software. A prototype of the proposed converter controlled by TMS320C2000 microcontroller for an output power of 200 W is tested and validated with the simulation results. The proposed system is used for powering devices like robots in critical applications such as military, space craft, etc., where stability, speed, and accuracy are major concerns. [ABSTRACT FROM AUTHOR]

This paper proposes a model predictive flux control (MPFC) strategy with cost function-based field weakening (FW) strategy for permanent magnet synchronous motor (PMSM). The stator flux vector is used as the control variable and the cost function of the proposed MPFC is configured in the form of flux increment, which can reflect the saturation degree of the inverter output. A novel space flux vector plane is introduced to explain the principle of optimal switching state selection in the proposed MPFC. The voltage and current limitations of the inverter in the high-speed region are analyzed in the flux plane to reveal the objective of FW compensation. The value of the cost function is controlled with a proportional integral controller in the proposed cost function-based FW strategy. Moreover, the reference flux vector is compensated with the output of the FW controller to enlarge the operation region of the stator flux vector. With the proposed FW strategy, the operation range of the PMSM is extended and the torque output in high-speed range is increased. Experimental studies are carried out to verify the validity and effectiveness of the proposed strategy. [ABSTRACT FROM AUTHOR]

As a combination of the switched-mode converter and linear amplifier, the switch-linear hybrid (SLH) envelope tracking (ET) power supply can achieve high efficiency and high tracking bandwidth simultaneously, and it can be classified into three types, namely, series-form, parallel-form, and series–parallel-form. In the SLH ET power supply, interaction may occur between the converters, and as a result, the controlled variable will deviate from its target. In this paper, the interaction in the series-form SLH ET power supply with different structures is analyzed first from the aspects of control and parasitic capacitances, and the feedforward control scheme and/or filter is adopted to eliminate the interaction. Then, for the parallel-form SLH ET power supply, four current control methods are introduced and compared from the current tracking and disturbance-rejection performances, and the method for suppressing the disturbance is presented. Since series–parallel-form SLH ET power supply contains at least three converters, the interaction is more complex. On the basis of the analysis of the series-form and parallel-form SLH ET power supplies, the interaction between the converters in series–parallel-form SLH ET power supply is analyzed and followed by the corresponding elimination method. Finally, one series-form, and one parallel-form SLH ET power supplies are implemented in the lab, and the experimental results verify the theoretical analysis. [ABSTRACT FROM AUTHOR]

In this paper, a method is proposed to eliminate the voltage ringing problem in a phase-modulated dc–ac converter, also known as a micro-inverter. The basic idea is to apply a time-critical two-stepped voltage waveform to the input of the converter bridge connected to the filter inductor. This method is implemented by a new topology that has one more switching leg added to the full bridge voltage fed converter. It produces a second voltage level and adds it to the first by using a transformer. The advantages of the proposed method are as follows. It almost eliminates the requirement of a voltage clamp, there is no circulating current in the freewheeling state, and the secondary side devices have less voltage and current stress compared to a conventional phase-modulated converter. The overall benefit is an improvement in converter efficiency even for a high-voltage conversion ratio application. The proposed topology operates with a secondary side modulation scheme that achieves zero-voltage switching of four devices on the primary side and either zero-voltage switching or zero-current switching of all the devices on the secondary side, over the entire line cycle of the ac output. Finally, the experimental results verify the proposed method. [ABSTRACT FROM AUTHOR]

Pulsed power loads (PPLs) are becoming prevalent in medium-voltage naval dc micro-grids. To alleviate their effects on the system, energy storages are commonly installed. For optimal performance, their interface converters need to have fast dynamics and excellent disturbance rejection capability. Moreover, these converters often need to have voltage transformation and galvanic isolation capability since common energy storage technologies such as batteries and supercaps are typically assembled with low-voltage strings. In order to address these issues, a moving discretized control set model predictive control (MDCS-MPC) is proposed in this paper and applied on a dual-active-bridge converter. Fixed switching frequency is maintained, enabling easy passive components design. The proposed MDCS-MPC has a reduced prediction horizon, which allows low computational burden. The operating principle of the MDCS-MPC is introduced in the development of a cost function, which provides stiff voltage regulation. Resonance damping and sampling noise resistance can also be achieved with the proposed cost function. An adaptive step is introduced to enable a fast transition. Assessments on the performance of the proposed MDCS-MPC are conducted. Comparisons with other control methods are also provided. Experimental validations on a 300 V/300 V 20-kHz 1-kW dual-active-bridge converter are carried out to verify the theoretical claims. [ABSTRACT FROM AUTHOR]

In a conventional linear-control design of a higher order power-electronic system (PES), the gains of the control laws are typically determined by small-signal analysis of the averaged model of the PES. The closed-loop control of such a PES (driving a pulsating load that periodically shifts the equilibrium) using its small-signal model is often found to be unsatisfactory with regard to the overall stability and performance. To address the challenges in control design for a PES driving such a nonlinear time-varying pulsating load, this paper delineates an optimal switching-sequence-based control (SBC) scheme, which applies stability-bound switching sequence(s) to the PES. A novel method has been formulated to ensure the reachability of the PES dynamics based on its switching sequence in terms of the time horizon of the switching sequence and the allocation of this time among the switching states of the same switching sequence. This is ascertained by modeling the PES and the pulsating load as a nonlinear map and then using this map and multiple Lyapunov functions determined by solving a set of linear-matrix inequalities corresponding to each of the switching states of a given switching sequence. It has been further shown that the knowledge of the stability bounds of a reachable switching sequence helps in reducing the online computation time for optimal SBC associated with solving the optimization problem by reducing the overall search space. Finally, to validate the optimal SBC, an experimental GaN-FET-based 100-kHz  Ćuk-PES has been fabricated and tested on a pulsating load. The overall SBC is implemented on a low-cost TMS320F28335 DSP, which also implements an observer to preclude the need for plurality of sensors for the higher order Ćuk-PES. The overall performance of the SBC is found to be satisfactory under varied dynamical conditions. [ABSTRACT FROM AUTHOR]

This paper presents the circuit design and magnetic integration of push–pull class-E inverters for wireless power transfer (WPT) up to megahertz. The design criterion for achieving zero-voltage switching (ZVS) of a class-E inverter with coupled windings is derived mathematically. The approaches of magnetic integration for push–pull class-E inverters are analyzed and compared. Then, a new magnetic structure with hybrid magnetic materials is proposed to build the integrated inductors with either coupled windings or uncoupled windings. A 3-MHz WPT system is built to verify the analysis. The detailed comparison of the class-E inverters with magnetic integration is presented in terms of switch voltage, efficiency, harmonic currents, and thermal distribution. In the optimized design example, the switches keep ZVS over the entire load range without using any closed-loop control. The system efficiency reaches 87.1% at 350-W output power. [ABSTRACT FROM AUTHOR]

DC circuit breakers (DCCBs) are vital for the safe and continuous operation of large high-voltage dc grids. Insulated-gate bipolar transistor-based hybrid DCCBs (IHCBs) can interrupt currents quickly and have good operational characteristics. Thyristor-based hybrid DCCBs (THCBs) are superior to IHCBs in terms of interruption capacity because of the large surge current capacity of thyristors. Nevertheless, existing THCBs have limitations regarding one or more of the following characteristics: pre-activation, fast reclosing, quick interruption of small current and no requirement for an additional pre-charge source. This paper proposes a thyristor full-bridge-based dc circuit breaker (TFCB) with all favorable characteristics mentioned above. The TFCB contains a main conductor, a main breaker (MB), an auxiliary branch, and an energy absorber. After an interruption, the capacitor in the TFCB can restore its initial voltage quickly to guarantee that the TFCB is available for the next interruption. Quick interruption of small currents is achieved using the additional charge current provided by the auxiliary branch. Pre-activation is achieved using the conduction path in the MB. The parameter designs are analyzed to ensure that the TFCB reliably interrupts currents without damaging itself. The proposed TFCB is validated using prototype experiments and PSCAD/EMTDC simulations. [ABSTRACT FROM AUTHOR]

Generally, battery-fed capacitive loads are charged to high voltages in series of switching cycles with smaller fragments of energy delivered to the load in every cycle to ensure an efficient charging process. In high voltage low power (HVLP) flyback charging circuit, significant portion of input energy drawn from the source in a cycle is utilized by the effective parasitic capacitance of the HV transformer and semiconductor devices and circulated back to the source at the end of the cycle. This reduces the energy delivered to the load per cycle and hence the net energy delivered in the charging process. In this paper, an energy-based analysis and simplified energy-based model for HVLP charging circuits is derived. An energy-based approach is appropriate to describe and define the HVLP converter behavior in terms of load energy component and circulating energy component. The derived energy-based model is extended to obtain analytical closed-form expressions governing the essential parameters of the charging circuit. The proposed energy-based model and analytical formulation of essential parameters are experimentally validated on a 0–2.5 kV programmable high voltage charging circuit prototype fed from 12 V input battery source. [ABSTRACT FROM AUTHOR]

This paper presents a self-adapting synchronized-switch harvesting (SA-SSH) interface circuit to extract energy from vibration-based piezoelectric energy harvesters (PEHs). The implemented circuit utilizes a novel switching technique to recycle optimum amount of harvested charge on piezoelectric capacitance to strengthen the damping force, and simultaneously achieve load-independent energy extraction with a single inductor. Charge recycling is realized by adjusting extraction time, and optimized through a maximum power point tracker based on charge-flipping dissipation. The circuit has been implemented using 180 nm HV CMOS technology with 0.9 × 0.6 mm2 active area. Self-adapting SSH circuit has been validated with both macro-scaled and MEMS PEHs with different inductor values. The interface circuit provides maximum energy extraction for the full storage voltage range of 1.8–3.7 V. The implementation harnesses have 500% more power compared to an ideal full-bridge rectifier, and output 3.4 μW for 2.24 V peak-to-peak open-circuit piezoelectric voltage from MEMS PEH excited at its resonant frequency. [ABSTRACT FROM AUTHOR]

In the no-load condition, LLC converter usually fails to regulate its output voltage although it operates at a high switching frequency. Till now, it is hard to obtain the exact relationship between design parameters and the maximum switching frequency for no-load regulation capability. In this paper, a specific criterion for no-load regulation of LLC converter is provided, without using active components or other modulation schemes. By analyzing the macroscopic switching period and microscopic switching transition in the no-load condition, it is shown that not only the peaking resonant current during the switching transition, but also the resonant tank design affect the no-load regulation of the LLC converter, which affects the no-load regulation capability. Furthermore, the relationship among design parameters is analyzed and the design guideline is also provided to achieve no-load regulation at the specified maximum switching frequency. To verify the effectiveness of the proposed design, 400 V input and 50 V/200 W output prototype is built and tested. [ABSTRACT FROM AUTHOR]

Multi-phase magnetically coupled resonant (MCR) wireless power transfer (WPT) technology can fulfill the requirements of time-varying spatial positions of loads in mid-range applications, as it can generate a rotating magnetic field around sending coils, and effectively reduce the limits of spatial positions on transfer characteristics including output power and transfer efficiency. Nevertheless, the design of coils parameters and control strategies put a great influence on the realistic transfer characteristics, which should be considered elaborately in practice. In this paper, a three-phase MCR WPT system with cylinder-shaped coils is investigated, the equivalent circuit model is built to carry out the theoretical analysis. Based on that, the influence on zero-voltage-switching (ZVS) conditions of power switches and the output power of the system, resulting from different phase-shifted angles between each phase, coil turns and angular misalignments of the receiving coil, is analyzed comprehensively. Detailed discussions on relationships among coil turns, the angular misalignment, ZVS conditions, and the output power are completed under different phase-shifted angles. Furthermore, the parametric optimization of coil turns, as well as phase-shifted angles, are proposed to ensure the power switches realize ZVS and ensure the system realize stable output power within the full range of angular misalignment. Finally, experiments are carried out to evaluate the accuracy of theoretical analysis and confirm the validity of the proposed optimal design. [ABSTRACT FROM AUTHOR]

Three-phase current reconstruction techniques with a single current sensor have been studied for permanent magnet synchronous machines (PMSMs) drive system due to its reducing cost and volume. In order to minimize the current reconstruction dead zone in the conventional method with a single dc-link current sensor, a strategy to couple multiple available positions through the single current sensor is proposed in this paper. With the proposed method, two independent equations of the stator currents can be obtained by sampling the single current sensor twice in both zero voltage vectors and active voltage vectors. By solving these two equations, the phase current reconstruction can be achieved accurately, which moves the current reconstruction dead zone toward six corner area of the space vector hexagon. Meanwhile, in order to guarantee the proposed method suitable in the whole linear modulation region, the suitable selection of the pulsewidth modulation switching period is analyzed in detail. Furthermore, the optimal selections of multiple sampling positions are discussed to lower the actual implementation difficulty of the proposed method. Finally, the experimental results on the PMSM demonstrate that the reconstructed phase currents with the proposed method can be always in consistent with the actual measured currents under different working conditions. [ABSTRACT FROM AUTHOR]

This paper presents a reduced component count five-level inverter topology based on the stacked cell approach to multilevel inverters. The proposed topology utilizes the fundamental properties of three-phase voltages to reduce the number of switches and flying capacitors to cut size, weight and costs while facilitating higher reliability, simpler wiring and lesser electromagnetic interference. The operational aspects of the topology such as circuit structure, modulation and capacitor balancing are explained, followed by an account of device stresses and reliability. A discussion of certain additional features such as fault tolerant operation, loss steering and common-mode elimination addresses the usefulness of the topology in practical situations. A comparison of the proposed topology with existing methods in terms of several parameters is then used to highlight its merits and features. Finally, experimental results obtained using an induction motor drive incorporating the topology are given, so as to validate the feasibility of the proposed approach. [ABSTRACT FROM AUTHOR]

The low-frequency fluctuation over the capacitor voltages seriously limits the development of medium-voltage variable-speed drives with a modular multilevel converter (MMC). Therefore, this paper presents an effective strategy of the low-speed and start-up operation for an MMC-based motor drive. The proposed strategy properly coordinates the improved injection and the reduced average capacitor voltage with high applicability. The specific interactions between the control parameters and the system metrics are analyzed to give the detailed steps of the parameters designing. Hence, based on the derivations, the proposed method enables the low-frequency operation under the nominal load torque with decreased injected components and reduced peak capacitor voltages. What is more, two start-up strategies that, respectively, aim at different objectives for the coordinated strategy are proposed, indicating satisfying control performances for the practical applications. The injected common-mode voltage and circulating current in the proposed method are designed to have a great reduction. Thus, the unfavorable risks for the motor are evidently decreased for better stability. The reduced peak current also lessens the high stress on switching devices with desirable reliability. The simulation and experiment results of an MMC-based motor drive prototype prove the effectiveness and superiority of the proposed method. [ABSTRACT FROM AUTHOR]

This paper presents a delta-sigma modulation (DSM) control scheme for noninverting buck–boost (NIBB) converter that features a duobinary encoding for four power switch controls. The proposed scheme converts the single-bit output of the modulator into a 1.5-b signal to enable a three-phase operation comprising the charging, bypassing, and discharging phases. This control method reduces both switching and conduction losses by changing only two switches in each period, thus, achieving high conversion efficiency. A smooth mode transition is provided by the DSM controller, which automatically and continuously determines the operating mode of the converter. Thus, the dead zone can be effectively released with improved transient responses. Furthermore, the spurious tones in the output are effectively eliminated by the robust noise shaping capability of the modulator. The proposed DSM-based NIBB converter was implemented on a 180-nm CMOS. It regulated the output in the range of 2.0–4.6 V with input voltage of 2.5–5.0 V, and the maximal load current was 500 mA. The converter showed a peak efficiency of 94.8% at 90-mA load and the output voltage ripples were maintained under 18 mV. A low noise floor with the first spurious peak located –92 dBc below the signal was achieved across all mode operations. In addition, the converter occupied a small chip area of 1.51 mm2. [ABSTRACT FROM AUTHOR]

In this paper, a new low-voltage ringing zero voltage transition (ZVT) cell is proposed for a family of non-isolated dc–dc converters. In the proposed converter, all semiconductor devices operate under soft-switching condition at both turning on and off. The proposed ZVT cell resolves the issues appeared in the previous works: no online calculation required to achieve ZVS turn-on of the main switch; no extra voltage stress imposed on the main or snubber components; no floating gate driver required for the main and snubber switches; low component count of the ZVT cell; operation principles and design guideline of the boost converter with the proposed ZVT cell are presented. Also, three different positions of a snubber diode considering its junction capacitor are analyzed to clarify the advantage of the proposed ZVT cell. A 2-kW laboratory prototype of the boost converter with the proposed ZVT cell operating at 100 kHz is built and tested to verify the theoretical analysis. Finally, a comparative analysis is given to demonstrate the superiority of the proposed converter. [ABSTRACT FROM AUTHOR]

This paper presents a model predictive current control (MPCC) for three-phase four-switch converters (TPFSC) connected to surface permanent magnet synchronous generators (SPMSGs) in oscillating water column (OWC) wave energy plants, that brings some benefits over the existing control methods used in this type of plants. The proposed MPCC for TPFSC follows the current references with great accuracy, whereas the switching frequency of the insulated-gate bipolar transistor (IGBTs) is fixed and low. This method minimizes the current reference tracking error, and its fast response makes it suitable for the power take-off systems present in wave energy converters. Furthermore, the system features a fast capacitor voltage offset suppression control. The dynamic performance and the voltage offset control of the proposed strategy for TPFSC feeding a SPMSG is evaluated in the Simulink environment. Later, experimental studies are carried out on an 8.7 kW laboratory SPMSG prototype. Finally, the capability of the proposed method to harvest the maximum energy from irregular waves is assessed using an OWC power plant emulator. [ABSTRACT FROM AUTHOR]

As research in matrix converters (MCs) has progressed over time, space vector modulation has emerged as the most popular technique for their modulation. Lately, model predictive control (MPC) has also been explored for the modulation and control of MCs, primarily gaining popularity due to the ease in realization of multiple objectives, as desired in MCs. However, multi-objective MPC employs assignment of weights to each control objective, wherein weight tuning is either empirical in nature or computationally cumbersome. This paper proposes a new modulation technique for MCs, inspired from delta sigma modulation for voltage source converters, that can be used for load voltage and source current control of MCs. Since source currents are samples of the load current envelope, it is required that this envelope be known for the control of source current. To eliminate load current sensors, predictive model of the load is used in envelope estimation. Further, independent switching schemes are generated for each objective, and an error minimization approach is used in integrating the two schemes into a final state selection, hence eliminating weighing factors. Unlike MPC, error predictions for all states of MCs, are not needed, hence facilitating easier implementation without significant processor burden, besides ensuring the quality of response. [ABSTRACT FROM AUTHOR]

The three-level full-bridge (TLFB) dc−dc converter has been widely used in high-voltage, high-power applications. In the experimental test, the neutral-point voltage deviation appears; moreover, it has also been found out that if the flying capacitors are introduced, the input capacitor voltages could realize self-balance even if no active balancing solutions are adopted. In the previous publications, the role of flying capacitors is generally considered to extend the range of soft switching; however, the self-balance ability has not been mentioned or investigated in any publications thus far. In order to fill this gap, this paper provides the detailed mode operation analysis of the TLFB converter and reveals the cause of the imbalance. In addition, the mechanism of the self-balance ability provided by the flying capacitors is explained in detail, which gives a deep insight into the converter. At last, the influence factor of the voltage error in steady state has been analyzed, and the specific expression of the voltage error is also derived. The feasibility of the theoretical analysis is verified by the simulation and experimental results. [ABSTRACT FROM AUTHOR]

This paper proposes the predictive control with the discrete space-vector modulation (DSVM) for Vienna rectifier connecting to the permanent magnet synchronous generator (PMSG) of the wind turbine system (WTS). Since Vienna rectifier has the special operation principle, Vienna rectifier generates only the feasible eight voltage vectors, which can be a candidate vector for the predictive control, depending on the sign of the input currents. In the proposed predictive control, the feasible voltage vectors are extended from 8 to 19 consisting the 8 original voltage vectors and 11 virtual voltage vectors by using the DSVM for improving the current quality related to the torque ripple, vibration, and noise, and the neutral-point voltage balance with low voltage ripple is guaranteed by using the offset value calculated based on the model of two dc-link capacitors in Vienna rectifier. The scheme for reducing calculation burden is applied in selecting the candidate vector. In addition, the limited operation range for the maximum torque per ampere control of PMSG connected to Vienna rectifier is analyzed. The performance of the proposed predictive control with DSVM for Vienna rectifier with PMSGs is verified in simulation and experiment. [ABSTRACT FROM AUTHOR]

The emergence of applications which require high-voltage switches has created a tendency to use semiconductor device series stacks. These series stacks permit operation at blocking voltages above semiconductor elements’ nominal voltage. Insulated-gate bipolar transistors (IGBT) are currently utilized for controllability and switching speed, when these topologies are employed. The main challenge therewith is guaranteeing voltage balance between IGBTs, both when blocked and when switching transistors. Most of the methods which have been proposed to mitigate static and dynamic voltage unbalances increase transistor losses. The series stack loss-less high voltage switch (LHVS) which mitigates voltage unbalances, thus reducing switching losses, is presented in this paper. LHVS consists of a circuit, which ensures soft IGBT switching, an energy recovery circuit, and a gate delay compensation circuit. Additionally, the insulation voltage level is guaranteed to be equal between control circuit and high-voltage side of each IGBT. The operating principle of the LHVS is detailed in this paper, as is experimental validation which has been performed for three series stack modules. Static unbalances are reduced to 1%, while the differences between collector–emitter voltage curves in switching “on” do not surpass 8 ns, and switching losses are reduced by 41%, as compared to the hard-switching topology. [ABSTRACT FROM AUTHOR]

Without active control, the voltage fluctuations of the dc-link and flying capacitors in a 4-level hybrid-clamped converter (4L-HCC) become excessively large in low-frequency operation. This paper studies the switching state redundancy inherent in a 4L-HCC and proposes a new capacitor voltage balancing and stabilizing method to minimize the dc-link and flying capacitor voltage fluctuations. A straightforward algorithm is developed based on a logic table to select the suitable switching states. Verified by simulation and experimental testing results, the new method and algorithm virtually eliminate all the big voltage fluctuations of capacitors at low and zero frequencies, greatly enhancing the robustness and reliability of a 4L-HCC. The capacitor size can be reduced by more than 80% compared with the conventional method. [ABSTRACT FROM AUTHOR]

Digital peak current mode (DPCM) control is widely used for dc–dc converters operating in continuous current mode. However, current tracking delay (CTD) in the system is normally neglected in the modeling stage, which leads to poor compensator design and degraded performance. This paper investigates CTD effect in boost converter with different DPCM controls. Based on dynamic relationship between the reference current and actual inductor current, the CTD transfer functions are derived, which improves the accuracy of small signal model. Since CTD degrades the phase margin of the system, equivalent migration of right half plane zero is proposed to model CTD effect. This method is very simple and straightforward, which facilitates the compensator design. Furthermore, two novel DPCM control strategies with minimized CTD are proposed, and they are based on duty cycle restriction and duty cycle extension, respectively. Both controls greatly reduce the CTD effect and improve the response speed. Besides, the duty cycle extension benefits from an extended pulsewidth modulation (ExPWM). This optimizes the calculation algorithm and speed, while improving the time margin for digital calculations. Combined with the proposed models and controls, the CTD effect is greatly reduced. The effectiveness is verified through detailed simulations and experiments. [ABSTRACT FROM AUTHOR]

Despite several studies and approaches, the design of current controllers for grid-connected converters via LCL filters is still a challenging task. This is mainly due to the parametric uncertainties and the grid background voltage distortions to which the system is submitted. In order to overcome these inherent system challenges, this paper proposes a multiloop control framework that simplifies the system dynamics of the overall circuit by splitting it in two equivalent sub-circuits. An inner loop is implemented as a fast sliding mode controller that controls the filter capacitor voltage in a fast and robust way. As a result, the plant, viewed by the outer loop, yields a voltage-controlled voltage source connected to the grid through an L filter. Thus, multiple resonant controllers are included in the state-space representation of this simplified system, allowing the design of a state-feedback controller in the outer loop for asymptotic tracking of the grid current with disturbance rejection of the grid background voltage. Here, a discrete linear quadratic regulator algorithm is used for designing the state-feedback gains. A simple design procedure is presented, as well as simulations and experimental results, to show the good performance of the proposed control scheme even under significant uncertainties and disturbances of the system. [ABSTRACT FROM AUTHOR]

Numerous studies show that power semiconductors are significant contributors to the overall failure rate of pulsewidth modulation (PWM) voltage source rectifier (VSR) systems. Aimed at this problem, this paper presents an improved diagnosis system for open-circuit faults of a three-phase PWM VSR based on ac current distortion characteristics, which consists of a diagnosis module, a register module, and a decision module. The diagnostic module employs a hysteresis comparator to judge the change trend of the currents, and thereby diagnoses the single open-circuit (OC) faults. The register module is employed to achieve multi-switch OC fault diagnosis, and the decision module is used to output the final result. The proposed method extends the previous work to multi-switch OC fault conditions as well as improves the diagnosis accuracy. The experimental results show that the proposed method can correctly achieve fault diagnosis, including 6 kinds of single-switch faults and 15 kinds of different double-switch faults. Additionally, the proposed method also shows superior anti-interference performance and high robustness under abrupt load transient conditions, different power factor conditions, unbalanced and/or distorted grid voltage conditions, and different ac filter structure conditions. Furthermore, the average diagnostic time of this method is only 3.68 ms. [ABSTRACT FROM AUTHOR]

The inductance is an important parameter impacting current ripple calculation, usually with the assumption that the designed inductance performs ideally in most of voltage source inverters (VSIs) applications. However, the initial permeability of magnetic material usually descends when the winding current reaches or goes beyond the saturation limit. In such region of saturation, the implemented inductor does not perform as expected in design stages and its value varies with the bias current. In this paper, analysis and calculation of the current ripple are presented for a three-phase VSI with powder cores-based inductors, which reveals the calculation error of current ripple caused by the soft saturation nature of powder cores. Based on the equivalent single-phase model, the influence of inductance saturation on current ripple can be quantitatively evaluated. Then, a comparison of the current ripple calculation between considering and ignoring inductance saturation of implemented inductors is drawn in detail. Furthermore, under the condition of inductance saturation, the output current ripple peak-to-peak value of three phases is used as the constraint for variable switching frequency pulsewidth modulation (VSFPWM) design. A comprehensive method is developed to compensate the effect of inductance saturation in VSFPWM. At last, the effectiveness of the proposed strategy is verified by the detailed simulation and experiment. [ABSTRACT FROM AUTHOR]

In this paper, a comprehensive sliding mode control (SMC) loop design for a CLLC resonant converter is proposed. The major objectives of the proposed SMC are to improve the converter dynamics and to achieve a tight output voltage regulation with respect to any parameter variations and external disturbances. The sliding surface coefficients are selected to ensure both large- and small-signal stability for the robustness of the converter under different operating conditions. Furthermore, system dynamic performances considering the error dynamics and overshoots are investigated. To validate the proposed algorithm, a hardware prototype of a bi-directional CLLC resonant converter for plug-in electric vehicle applications is developed and tested up to 1 kW, and the effectiveness of the proposed control solution is verified by the load transients and start-up tests. At a 100% step-change in load power, the SMC achieves 1 ms settling time, which is approximately 0.9 ms faster than the conventional proportional integral control strategy. [ABSTRACT FROM AUTHOR]

This paper proposes a three-phase, five-level, non-regenerative pulsewidth modulated rectifier using only two active switches (minimum required) per phase, which drastically reduces gate driver requirement and hardware complexity. It draws sinusoidal input current at close to unity power factor. All the semiconductor devices are rated at only one fourth of the dc-link voltage, and none of them requires any transient voltage balancing snubber. A total of 8 out of the 14 diodes per phase undergo soft switching transition under all operating conditions, which increases its efficiency. No extra hardware circuitry for balancing the flying capacitors (FCs) or the dc-link mid-point voltage are required, which further reduces hardware complexity and increases the conversion efficiency. The proposed topology does not need any sophisticated startup procedure for charging the FCs either, which solves the problem of semiconductor overvoltage during starting. A 3-kW laboratory prototype is built to experimentally verify the proposed topology. The maximum efficiency obtained from the prototype is 98.7%, and it is always more than 96% for the load range from 15% to its rated. [ABSTRACT FROM AUTHOR]

The pulse-width modulated (PWM) switching rectification that can achieve a high power factor (PF) for increasing the energy transfer efficiency between an LC resonator and a rectifier and voltage step-up and -down conversion is proposed for a wireless power transfer (WPT) receiver. The proposed method can emulate the switching rectifier as a resistive load by using an inductor and integrated phase synchronizers. Additionally, similar to a switched-inductor converter that controls the duty cycle ratio (D), the proposed PWM rectifier can control the output voltage VOUT when the input is a rectified, wirelessly coupled voltage instead of a constant voltage. Thus, unlike a conventional PWM switching rectifier for ac mains, an additional voltage conditioning circuit would not be needed after the proposed rectifier for WPT. The proposed PWM switching rectification is implemented in the AMS 0.18 μm 1.8 V/5 V CMOS process. PF = 1 is measured, indicating the most efficient energy transfer, compared to only 0.55–0.65 in a peak detection rectifier. Additionally, 88.2% of peak power conversion efficiency of the switching rectifier is achieved, and the maximum output power is 80.3 mW at 500 kHz of the WPT frequency. Moreover, the measured voltage conversion ratios ranging between 0.73× and 2× are demonstrated in this paper. [ABSTRACT FROM AUTHOR]

This paper presents a novel seven-level inverter topology for medium-voltage high-power applications. It consists of eight active switches and two inner flying capacitor (FC) units forming a similar structure as in a conventional active neutral-point-clamped (ANPC) inverter. This unique arrangement reduces the number of active and passive components. A simple modulation technique reduces cost and complexity in the control system design without compromising reactive power capability. In addition, compared to major conventional seven-level inverter topologies, such as the neutral point clamped, FC, cascaded H-bridge, and ANPC topologies, the new topology reduces the dc-link voltage requirement by 50%. This recued dc-link voltage makes the new topology appealing for various industrial applications. Experimental results from a 2.2-kVA prototype are presented to support the theoretical analysis presented in this paper. The prototype demonstrates a conversion efficiency of around 97.2% ± 1% for a wide load range. [ABSTRACT FROM AUTHOR]

Fault tolerance in wind turbines is considered crucial to increase their reliability and availability levels. This paper presents a fault-tolerant direct-drive permanent magnet synchronous generator (PMSG) using new direct control techniques, with the ability to handle power semiconductor open-circuit faults in the full-scale back-to-back converter. The fault-tolerant topology consists of a five-leg converter, with a shared leg connected to a generator phase and to its corresponding grid phase, through a triode for alternating current (TRIAC). The main contribution of this paper consists of the development of an alternative direct torque control and direct power control schemes for both machine-side converter and grid-side converter, respectively. Moreover, a reliable fault diagnostics algorithm without requiring additional sensors is also integrated, providing the information required to instantaneously trigger fault-tolerant remedial strategies. Simulation and experimental results are presented to validate the effectiveness of the proposed fault-tolerant PMSG drive. [ABSTRACT FROM AUTHOR]

Phase-shift full-bridge (PSFB) converter is a widely used topology for high-efficiency and high-power applications, thanks to low voltage/current stress of all components and zero-voltage-switching operation of primary mosfets. The critical drawback of the PSFB converter is hard-switching characteristics of primary mosfets at a very light load, which causes severe thermal explosion and extremely high input power consumption, especially with the latest super-junction mosfet. To minimize the switching loss of the PSFB converter at a very light load, a new optimal dead-time control scheme with burst-mode operation is proposed in this paper and its validity is verified experimentally with the implemented 2.2-kW server power supply unit. [ABSTRACT FROM AUTHOR]

Traditionally, the communication between power converters connected in a microgrid is established using a wired method or a wireless droop method. The shortcomings of these methods have opened up the possibility of power-line-based communication between converters. However, the conventional power line communication systems have the disadvantages of using high-frequency data carrying signals that are prone to attenuation. These systems also make use of explicit couplers, transmitters, and amplifiers that adds to the overall cost and infrastructure. In this paper, a novel fractional harmonic $d\text{--}q$ domain based power line communication technique is proposed. A switched fractional harmonic current space vector is used to carry data. The primary control loop and the modulation algorithm of the converters are used for encoding and decoding of data. The proposed technique thus overcomes the disadvantages of the conventional power line communication systems and at the same time carries forward the advantages of it. The proposed technique is validated with sufficient experimental test results. [ABSTRACT FROM AUTHOR]

Clamp mode snubbers are very well suited for the series structure of the insulated-gate bipolar transistors (IGBTs) in pulsed power applications. They properly meet the necessities expected from them such as the fast operating of the series IGBTs since they have no effect on the gate side. In addition, they can provide safe voltage condition for the IGBTs in short circuit faults, which are very probable in pulsed applications. The clamp mode snubber can perform its voltage balancing task whenever the power capacity of the snubber can support the injected powers due to the voltage unbalancing factors. This paper initially introduces the main factors injecting power to the snubbers. Then, it will be illustrated that the exact injected power to each predetermined snubber cannot be determined due to the uncertainties about the effect of the voltage unbalancing factors. Although it is impossible to determine the exact value of the power injected to each snubber, the total injected powers to the snubbers can be calculated. Therefore, as an effective remedy, this paper proposes a concentrated snubber. Using the proposal, all the injected powers are conducted to a centralized circuit and can be easily managed. In addition, analytical expressions are provided for proper dimensioning of the proposed concentrated snubber elements. Furthermore, the performance of the proposed concentrated snubber is evaluated using simulations and experimental prototyping. [ABSTRACT FROM AUTHOR]

This paper presents a method that overcomes the problem of the confusion during fast irradiance change in the classical maximum power point tracking (MPPT) as well as in model predictive control (MPC)-based MPPTs available in the literature. The previously introduced MPC-based MPPTs take into account the model of the converter only, which make them prone to the drift during fast environmental conditions. Therefore, the model of the photovoltaic (PV) array is also considered in the proposed algorithm, which allows it to be prompt during rapid environmental condition changes. It takes into account multiple previous samples of power, and based on that is able to take the correct tracking decision when the predicted and measured power differ (in case of drift issue). After the tracking decision is taken, it will be sent to a second part of the algorithm as a reference. The second part is used for following the reference provided by the first part, where the pulses are sent directly to the converter, without a modulator or a linear controller. The proposed technique is validated experimentally by using a buck converter, fed by a PV simulator. The tracking efficiency is evaluated according to EN50530 standard in static and dynamic conditions. The experimental results show that the proposed MPC-MPPT is a quick and accurate tracker under very fast changing irradiance, while maintaining high tracking efficiency even under very low irradiance. [ABSTRACT FROM AUTHOR]

In ac motor drives, the fixed-frequency harmonic components of output voltage and current from the inverter with fixed-frequency pulsewidth modulation usually lead to electromagnetic interference (EMI). The spread spectrum clock generation (SSCG) is a widely used solution for this problem. Adjusting the switching frequency to reduce EMI is one kind of practicable scheme among SSCG methods. How to design an optimal or suitable modulation profile is a research emphasis of scholars and has been discussed in depth in many literatures. However, apart from the modulation profile, the mode and quality of carrier are also important and can be improved. In most frequency modulation methods, due to the limitation of the conventional carrier generation mode, the implementation of the new frequency instruction has to wait for the termination of the last switching period. In order to eliminate the waiting state and design a simpler algorithm, this paper has proposed a wait-free phase-continuous carrier frequency modulation (WPCFM) strategy by combining the direct digital frequency synthesizer theory and proper temporal planning of control interruptions. Besides, a theoretical analysis of WPCFM, including quantization error, frequency jitter, phase delay, and voltage distortion, has been finished. Moreover, compared with conventional methods, a more convenient, feasible, and simpler field-programmable gate array based algorithm implementation method and the control structure of WPCFM are also introduced. The analysis shows that, although WPCFM causes a slight increase of the current ripple, it can solve the partial frequency nonuniform distribution problem of the conventional method, and it has a potential value of applications in the wide band gap motor drive systems. The effectiveness of the WPCFM is verified by several sets of EMI reduction experiments where classical periodic carrier frequency modulations are applied. [ABSTRACT FROM AUTHOR]

This paper introduces a novel modeling approach that allows to obtain fast simulations of pulsewidth-modulated dc–dc switched-mode power supplies (SMPS). The proposed methodology combines the use of precise switched models during transient evolutions and averaged models during steady-state or slowly varying conditions. In that way, the resulting mixed modeling approach enables to obtain the detailed switching behavior of SMPS in the context of long-term simulations. The commutation between models is automatically performed in runtime by an algorithm that detects the transient or slowly varying condition according to the evolution of some model variables. When the precise switched model is used, the mentioned algorithm also adjusts the averaged model parameters so that its results are accurate irrespective of the operating point. This paper also describes the implementation of the methodology in the Modelica language and reports simulation experiments showing that the results are as accurate as those obtained using precise switched models, but several times faster. [ABSTRACT FROM AUTHOR]

In this paper, a robust adaptive sliding-mode observer (SMO) is designed based on the surface permanent-magnet synchronous machine (SPMSM) model in rotor reference frame ($\gamma \delta $ -axis), and an online inverter nonlinearity identification and compensation method is proposed. In order to reduce the chattering of the SMO, an adaptive law is presented to help estimate the back electromotive forces of an SPMSM; thus, smaller gains can be set for switching functions of the SMO. The small-signal model of the proposed sensorless scheme is derived for analyzing the steady-state and dynamic behavior of the sensorless scheme. Voltage distortion, caused by nonlinear characteristics of switching devices, not only causes (6k ± 1)th harmonics in phase currents but also leads to a rotor position estimation error. The equivalent amplitude of the voltage distortion can be identified based on the derived small-signal model of the proposed sensorless scheme. To improve the accuracy of the estimated voltage distortion, a recursive restricted total least squares is applied to obtain the estimated amplitude of the voltage distortion. Experimental results validate the proposed sensorless control scheme and its effectiveness. [ABSTRACT FROM AUTHOR]

This paper presents a multi-period frame transient switching control (MP-TSC) scheme for buck converter with a controlled coupled inductor, aiming at improving the load transient response. The proposed buck converter utilizes a controlled coupled inductor as the output inductor. During a load transient, the coupled inductor is controlled as a small equivalent inductance so as to achieve fast transient regulation. While in the steady state, the coupled inductor behaves as a large inductance to reduce the output current ripple. Furthermore, on the basis of the proposed variable inductance circuit, an MP-TSC control scheme is proposed and implemented in a digital form. With the proposed control scheme, the load transient event is divided into n + 1 sub-periods, and in each sub-period, the capacitor-charge balance principle is used to determine the switching time sequence. Moreover, the control principle design and transient response index analysis are provided. Furthermore, its feasibility is validated in simulation and experiment with a 12–3.3V low-voltage high-current synchronous buck converter. Experimental results demonstrate that the voltage deviation of the proposed MP-TSC scheme (coupled coefficient of the controlled coupled inductor is 0.52) has improved by more than 79% compared to that with the auxiliary circuit disabled. [ABSTRACT FROM AUTHOR]

Multilevel inverters (MLIs) are being used in wide range of power electronic applications. These converters have attracted a lot of attention during recent years and exist in different topologies with similar basic concepts. This paper presents five main submodules (SMs) to be used as the basic structures of MLIs. The paper reviews the common MLI topologies from the structural point of view. The topologies are divided into the different SMs to show conventional MLI configurations and future topologies that can be created from the main SMs. A comparative study between different topologies is performed in detail. The MLIs are categorized and investigated with from different perspectives such as the number of components, the ability to create inherent negative voltage, working in regeneration mode and using single dc source. [ABSTRACT FROM AUTHOR]

As cascaded proportional-integral controllers involve complicated tuning work, many efforts have been focused on direct controllers. Direct torque control and predictive torque control are both feasible solutions. However, bigger ripples or weighting factor designs are not easily solved. In this paper, a direct current controller that uses an extended high-gain state observer is proposed. The integral controller is removed from the system by using a disturbance estimation technique, which improves the system's performance with a variety of loads. A direct current controller without weighting factors is proposed as the inner controller. Unlike existing direct control methods, all phase currents are considered equally in the controller, which ensures a high current control quality. The simulation and experimental results verify that the proposed method performs well both in steady and transient states. [ABSTRACT FROM AUTHOR]

This paper discussed an active-bridge-active-clamp (ABAC) topology that is suitable for highpower more-electric-aircraft applications. Though conventional modulation techniques can be applied to ABAC converters, they present drawbacks, such as increased low-voltage (LV) current ripple and limited power transfer capability. To address these problems, a phase-shift-modulation (PSM) scheme is proposed to provide clean dc terminal current at the LV side while maintaining high power transfer capability and efficiency in a wide operating range. The proposed PSM has a complete switching harmonics cancellation on the LV terminals independent of the operating conditions. This results in high quality power without any ac components, thus minimizing passive filtering. In addition, when terminal voltages vary from their nominal values, the proposed PSM can improve the maximum power transfer capability of the ABAC converter compared to the conventional approach. The theoretical claims are validated by both simulation and experimental results on a 10-kW 270-V/28-V ABAC converter. [ABSTRACT FROM AUTHOR]

In this paper, a systematic and analytical study of non-isolated topologies belonging to the family of reduced redundant power processing (R2P2) converters is presented. Based on this study, all the non-isolated R2P2 topologies that can be implemented in reality are derived. Detailed examples clarify all possible cases of this analysis. In addition to this, the voltage ratio and the efficiency for each one of the R2P2 configurations are calculated, being further illustrated with examples. A comparison among configurations is also discussed with criteria the high step-up voltage gain and efficiency, aiming for high-power applications. One of these R2P2 converters is selected for further examination, as the most suitable for such applications. The theoretical analysis, as well as the calculations of the step-up voltage ratio and efficiency of the selected converter, is compared to experimental results conducted on a 2-kW laboratory prototype designed to operate in various step-up voltage ratios and in a high-power range, proving the effectiveness of the proposed investigation. [ABSTRACT FROM AUTHOR]

The pulse-density-modulation (PDM) zero-voltage-switching (ZVS) full-bridge converter is a promising power converter for wireless power transfer (WPT) systems. The converter has the advantages of both direct conversion ratio control and load-independent soft switching. These advantages reduce the overall system complexity and power loss. However, the converter suffers from the limitations of large low-frequency subharmonics, a narrowed modulation range, and a large modulation delay. These limitations are caused by the existing PDM strategy, which was designed to generate a symmetric ZVS current to ensure the ideal ZVS for minimizing the switching loss. This paper finds that even with an asymmetric ZVS current, the ideal ZVS can still be ensured by the negative feedback effect of the dead-time voltage. Based on this finding, a PDM strategy that allows asymmetric ZVS currents is proposed to overcome the aforementioned limitations. In experiments, a ZVS full-bridge converter was modulated by the existing and the proposed PDM strategies, respectively. The converter performances and responses were compared and the results showed that the proposed PDM strategy can overcome the limitations while achieving ZVS. The proposed PDM strategy was also tested in a WPT system for verification. [ABSTRACT FROM AUTHOR]

This paper proposes a new class of topologies of single-stage high-frequency ac-link power converters, which is capable of providing both voltage step up/down within a wide frequency and voltage ranges. The proposed family, which supports bidirectional power flow, can interface various single/multi-port dc and/or single/multi-phase ac systems to provide dc–dc, dc–ac, ac–dc, or ac–ac power conversion. In this family of converter, which offers a very modular structure, a small inductor that forms the link exchanges power entirely or partially between the source and load. The proposed family can function in buck, boost, and/or buck–boost modes of operation, and a combination of these modes of operation is also feasible. In comparison to the parallel inductive four-quadrant link converters, the proposed family features a significantly reduced link peak current, reduced switch ratings, and reduced total number of power switches. These features enhance the efficiency, reduce the total cost, and increase the power density of the system. In order to further improve the overall efficiency of the system, minimize the current/voltage stress over all utilized semiconductor devices, and lower electromagnetic interference (EMI), a small capacitor is placed in parallel with the link inductor to realize soft-switching operation for the proposed configurations. Moreover, the proposed converters have the potential to incorporate a lightweight single-phase high-frequency transformer for electrical isolation. The proposed circuit topologies prevent reverse recovery issues and eliminate losses corresponding to body diodes of power switching devices via utilizing power switches in conjunction with external fast recovery diodes. The proposed family offers a very high level of reliability owing to its immunity from short circuit of input and output terminals and open circuit of the link inductor, which may occur in other power converters due to commutation problem resulting from a short deadtime or an overlap time between switches, unwanted control command, delay in electronic circuits, or EMI noise's misgating on or off, in addition to the absence of electrolytic capacitors in the power circuit. A control approach is also developed to regulate input and output currents in one stage of power conversion. A detailed theoretical analysis, operation, design methodology, and control strategy of the proposed family are provided in this paper, and the effectiveness and performance of the proposed converter family are verified via simulation results and experimentally. [ABSTRACT FROM AUTHOR]