Search

Currently, meter-long guideways rarely achieve an accuracy of dozens of nanometers due to processing difficulties such as the material and the edge effect. In this paper, we focus on this problem and propose a set of optimization processing methods to cope with it. In the grinding stage, a grinding tool is designed to improve the reciprocating processing and address the problem of warping; in the polishing stage, three different processes are compared, and the combination of magnetorheological finishing technology and the polyurethane disc technology process is purposed to reduce the polishing cycle and improve the surface figure accuracy. Moreover, through the combined process of magnetorheological finishing and smoothing, the edge effect and medium- and high-frequency error are essentially suppressed. The meter-long guideway is achieved with an accuracy of dozens of nanometers. Although the sizes of surface A/C and B/D are 1000 mm × 240 mm and 1000 mm × 160 mm, the surface figures are 20.33 nm, 22.78 nm, 39.23 nm and 26.58 nm RMS (Root Mean Square), respectively. The nanometer accuracy guideway is critical to an ultra-precision machine tool. Finally, the X-axis straightness of the profile measurement system formed by the guideway reaches 200 nm/600 mm. [ABSTRACT FROM AUTHOR]

An aerostatic spindle is a core component in ultra-precision machine tools. The rotor of the spindle has extremely high manufacturing accuracy, which cannot be directly achieved via traditional machining, but always via manual grinding. The deterministic figuring theory is introduced into the machining of shaft parts, which overcomes many shortcomings of manual grinding. The manufacturing error of the shaft's surface contains different frequency components, which have different effects on its working performance and the figuring process. Because the deterministic figuring method can only correct the error within a limited frequency range, in order to ensure high efficiency and high precision of the figuring process, we need to use reasonable filtering parameters to filter out the error with unnecessary frequencies. In this paper, the influence of contour error with different frequencies and amplitudes on the air film are analyzed using computational fluid dynamics (CFD) software, and the amplitude–frequency analysis as a function of the power spectral density (PSD) characteristic curve is used to study the filtering parameters of the measured data. After the figuring experiment using the filtering parameters obtained from the analysis, the average roundness of the shaft converged from 0.419 μm to 0.101 μm, and the cylindricity converged from 0.76 μm to 0.35 μm. The precision reached the level of manual grinding, which proves the rationality of the analysis using filtering parameters in a shaft's deterministic figuring. [ABSTRACT FROM AUTHOR]

The application of ultra-precision shaft parts is widely used, such as the spindle core of the air bearing spindle in ultra-precision machine tools. The precision of the spindle core is extremely high, and it is very difficult to obtain directly by traditional Computer Numerical Control (CNC) machine tools but is mostly obtained by manual grinding, whose machining efficiency is greatly limited. Based on the deterministic figuring theory, this paper focuses on the ultra-precision roundness, optimizing the filtering parameters of the measurement error data and studying the generation mechanism of the removal function morphology; the shape of the removal function is adjusted by combining the analysis of the figuring ability and positioning error. Finally, the optimized removal function is used on an experimental steel shaft, the average roundness convergence ratio is 72% higher than that of the original removal function, and the roundness reaches a 0.1 μm level. The result shows that a reasonable filtering of measured data and the removal function adjusted for the surface feature can improve the efficiency and precision of deterministic figuring on shaft parts. [ABSTRACT FROM AUTHOR]

Nanoscale laser damage precursors generated from fabrication have emerged as a new bottleneck that limits the laser damage resistance improvement of fused silica optics. In this paper, ion beam etching (IBE) technology is performed to investigate the evolutions of some nanoscale damage precursors (such as contamination and chemical structural defects) in different ion beam etched depths. Surface material structure analyses and laser damage resistance measurements are conducted. The results reveal that IBE has an evident cleaning effect on surfaces. Impurity contamination beneath the polishing redeposition layer can be mitigated through IBE. Chemical structural defects can be significantly reduced, and surface densification is weakened after IBE without damaging the precision of the fused silica surface. The photothermal absorption on the fused silica surface can be decreased by 41.2%, and the laser-induced damage threshold can be raised by 15.2% after IBE at 250 nm. This work serves as an important reference for characterizing nanoscale damage precursors and using IBE technology to increase the laser damage resistance of fused silica optics. [ABSTRACT FROM AUTHOR]

A deterministic figuring method for cylindrical surface based on abrasive belt polishing is proposed in this study in order to improve the geometric accuracy of metal shaft parts. The principal motion of material removal is performed through the axial oscillation of the abrasive belt, and the different material removal at different positions can be obtained through servo control of the machine tool spindle by removing high error spots on the cylindrical surface and finally deterministically corrects the roundness error. An abrasive belt-based deterministic figuring device was built, and the figuring experiments were performed on the surface of steel workpieces 100 mm in diameter and 130 mm in effective length. The roundness errors of the entire workpiece after twice figuring iterations decreased nearly from the initial 3 μm to 1 μm, which preliminary verified the feasibility of this method. This deterministic figuring method is expected to break the machining accuracy limit and improve the rotation precision of the precision shaft parts such as the aerostatic spindle. [ABSTRACT FROM AUTHOR]

Metallic elements can contaminate single crystal silicon mirror during ion beam etching (IBE) and other postprocessing methods, which can affect the performance of components in an infrared laser system. In this work, scanning electron microscope (SEM) and atomic force microscope (AFM) were used to characterize the distribution of contaminant represented by aluminum (Al). After characterizing contaminated area, elastic jet polishing (EJP), EJP, and static alkaline etching (SAE) combined technique were used to process the mirror. The morphology and laser-induced absorption were measured. Results show that metallic elements can mix with silicon and generate bulges due to the sputtering effect. In addition, SAE and EJP combined technique can remove metallic contaminant and stabilize the surface quality. Research results can be a reference on conducting postprocessing technologies to improve laser damage resistance property of single crystal silicon mirror in infrared laser system. [ABSTRACT FROM AUTHOR]