Search

Nanoimprint lithography (NIL) is a promising technique for fine-patterning with a lower cost than other lithography techniques such as EUV or immersion with multi-patterning. NIL has the potential of "single" patterning for both line patterns and hole patterns with a half-pitch of less than 20nm. NIL tools for semiconductor manufacturing employ die-by-die alignment system with moire fringe detection which gives alignment measurement accuracy of below 1nm. In this paper we describe the evaluation results of NIL the overlay performance using an up-to-date NIL tool for 300mm wafer. We show the progress of both "NIL-to-NIL" and "NIL-to-optical tool" distortion matching techniques. From these analyses based on actual NIL overlay data, we discuss the possibility of NIL overlay evolution to realize an on-product overlay accuracy to 3nm and beyond.

Since multi patterning with spacer was introduced in NAND flash memory1, multi patterning with spacer has been a promising solution to overcome the resolution limit. However, the increase in process cost of multi patterning with spacer must be a serious burden to device manufacturers as half pitch of patterns gets smaller.2, 3 Even though Nano Imprint Lithography (NIL) has been considered as one of strong candidates to avoid cost issue of multi patterning with spacer, there are still negative viewpoints; template damage induced from particles between template and wafer, overlay degradation induced from shear force between template and wafer, and throughput loss induced from dispensing and spreading resist droplet. Jet and Flash Imprint Lithography (J-FIL4, 5, 6) has contributed to throughput improvement, but still has these above problems. J-FIL consists of 5 steps; dispense of resist droplets on wafer, imprinting template on wafer, filling the gap between template and wafer with resist, UV curing, and separation of template from wafer. If dispensing resist droplets by inkjet is replaced with coating resist at spin coater, additional progress in NIL can be achieved. Template damage from particle can be suppressed by thick resist which is spin-coated at spin coater and covers most of particles on wafer, shear force between template and wafer can be minimized with thick resist, and finally additional throughput enhancement can be achieved by skipping dispense of resist droplets on wafer. On the other hand, spin-coat-based NIL has side effect such as pattern collapse which comes from high separation energy of resist. It is expected that pattern collapse can be improved by the development of resist with low separation energy.

A low cost alternative lithographic technology is desired to meet the decreasing feature size of semiconductor devices. Nano-imprint lithography (NIL) is one of the candidates for alternative lithographic technologies.[1][2][3] NIL has such advantages as good resolution, critical dimension (CD) uniformity and low line edge roughness (LER). On the other hand, the critical issues of NIL are defectivity, overlay, and throughput. In order to introduce NIL into the HVM, it is necessary to overcome these three challenges simultaneously.[4]-[12] In our previous study, we have reported a dramatic improvement in NIL process defectivity on a pilot line tool, FPA-1100 NZ2. We have described that the NIL process for 2x nm half pitch is getting closer to the target of HVM.[12] In this study, we report the recent evaluation of the NIL process performance to judge the applicability of NIL to memory device fabrications. In detail, the CD uniformity and LER are found to be less than 2nm. The overlay accuracy of the test device is less than 7nm. A defectivity level of below 1pcs./cm2 has been achieved at a throughput of 15 wafers per hour.

A low cost alternative lithographic technology is desired to meet with the decreasing feature size of semiconductor devices. Nanoimprint lithography (NIL) is one of the candidates for alternative lithographic technologies. NIL has advantages such as good resolution, critical dimension (CD) uniformity and smaller line edge roughness (LER). 4 On the other hand, NIL involves some risks. Defectivity is the most critical issue in NIL. The progress in the defect reduction on templates shows great improvement recently. In other words, the defect reduction of the NIIL process is a key to apply NIL to mass production. In this paper, we describe the evaluation results of the defect performance of NIL using an up-to-date tool, Canon FPA-1100 NZ2, and discuss the future potential of NIL in terms of defectivity. The impact of various kinds defects, such as the non-filling defect, plug defect, line collapse, and defects on replica templates are discussed. We found that non-fill defects under the resist pattern cause line collapse. It is important to prevent line collapse. From these analyses based on actual NIL defect data on long-run stability, we will show the way to reduce defects and the possibility of NIL in device high volume mass production. For the past one year, we have been are collaborating with SK Hynix to bring this promising technology into mainstream manufacturing. This work is the result of this collaboration.

In principal, the critical dimension (CD) of Nanoimprint lithography (NIL) pattern is determined by the CD of the template pattern. Unless one template is changed to another, NIL does not have a knob for direct control of the CD, such as the exposure dose and focus in optical lithography. Alternatively, the CD would be controlled by adjusting the thickness of the residual layer underneath the NIL pattern and controlling the etching process to transfer the pattern to a substrate. Controlling the residual layer thickness (RLT) can change the etching bias, resulting in the control of the CD of etched pattern. RLT is controllable by the resist dispense condition of the inkjet. For CD control, the metrology of RLT and feedback of the results to the dispense condition are extremely important. Scatterometry is the most promising metrology for the task because it is nondestructive 3D metrology with high throughput. In this paper, we discuss how to control CD in the NIL process and propose a process control flow based on scatterometry.

It is getting harder to minimize feature size to satisfy bit growth requirement. 3D NAND flash memory has been developed to meet bit growth requirement without shrinking feature size. To increase the number of memory cells per unit area without shrinking feature size, we should increase the number of stacked film layers which finally become memory cells. Wafer warpage is induced by the stress between film and wafer. Both of film stress and wafer warpage increase in proportion to stacked film layers, and the increase of wafer warpage makes CD uniformity worse. Overlay degradation has no relation with wafer warpage, but has indirect relation with film stress. Wafer deformation in film deposition chamber is the source of overlay degradation. In this paper, we study the reasons why CD uniformity and overlay accuracy are affected by film stress, and suggest the methods which keep CD uniformity and overlay accuracy safe without additional processes.

Recently, we found a peculiar acid induced defect on chemically amplified photo resist applied to sub- 30nm NAND Flash Memory. This defect is like a hole-pattern with about 1um diameter, and induced by diffusion of acid which makes photoresist soluble in developer, even though photoresist is not exposed with KrF. With some experiment results, we found out that HCl gas, by-product of high temperature oxide which is contained inside voids between two gate lines diffuses into photoresist through high temperature oxide from voids, makes photoresist soluble in developer, and eventually creates the hole-type defect on photoresist. To prevent this defect, we can suggest some methods which are substitution of KrF photoresist into I-line photoresist, modification of oxide deposition recipe to suppress by-product, and applying of non-CAR (Chemically Amplification Resist) type KrF photoresist not sensitive to acid.

While spacer is essential to separate the second lines from the first lines at negative tone spacer patterning technique, Spacer brings side effects such as increase in process step as well as CD budget induced by spacer. To eliminate these side effects, we have chosen the combination of photo resist as the first lines and developer soluble bottom ARC as the second lines at negative tone spacer patterning technique. This process scheme consists of only two mask steps; one is critical mask for the first lines in cell and peripheral cell, and another is non-critical mask for recess of the second lines in cell area and removal of the second lines in peripheral area. By the diffusion of acid from photo resist into developer soluble bottom ARC, developer soluble bottom ARC adjacent to photo resist of the first line is transformed into the substance, which can be easily removed by developer dispensed after the second mask exposure. With the adoption of developer soluble bottom ARC, we can expect to make progress in cost reduction at negative tone spacer patterning technique.

Double patterning technique using spacer which can avoid CD (Critical Dimension) uniformity problem mainly caused by overlay issue is one of the methods that could be applied to apply to manufacturing of memory devices. Though double exposure and etch technology (DEET) has comparative advantage in the number of process steps, it is required to dramatically improve overlay performance of current exposure tools for the realization of manufacturing. In this study, negative type-double pattering technique using spacer has been developed as the best way for the application of NAND flash memory device from the view point of CD uniformity and the number of mask layers used to complete double patterning. Negative type-double patterning technique using spacer consists of subsequent steps such as formation of poly line, spacer on sidewall of poly line, SOG gap fill into space between poly lines, SOG etch back, removal of spacer, and finally hard mask etch. We have used amorphous carbon as a spacer material to easily remove spacer from poly lines and adopted SOG material to easily fill in space between poly lines. When negative type-double patterning technique using spacer is applied to NAND flash memory device, we can expect that k1 factor of about 0.14~0.20 could be accomplished successfully.

Double Exposure Technology (DET) is one of the main candidates for expanding the resolution limit of current lithography tool. But this technology has some bottleneck such as controlling the CD uniformity and overlay of both mask involved in the lithography process. One way to solve this problem and still maintain the resolution advantage of DET is using spacers. Patterning with a spacer not only expands the resolution limit but also solves the problems involved with DET. This method realizes the interconnection between the cell and peripheral region by "space spacer" instead of "line spacer" as usually used. Spacer process involves top hard mask etch, nitride spacer, oxide deposition, CMP, and nitride strip steps sequentially. Peripheral mask was additionally added to realize the interconnection region. With the use of spacers, it was possible to realize the NAND flash memory gate pattern with less than 50nm feature only using 0.85NA (ArF).