Search

In renewable energy micro-source applications, a wide range of voltage conversion of the step-up converter is an essential part to equalize the typical low voltage of micro-source with DC-bus voltage of Inverter or motor drives. In order to meet this purpose, an ultra-voltage gain step-up DC-DC converter is proposed in this paper. The proposed converter has made an arrangement of the regenerative-boost fed switched inductor and capacitor configurations. Thereby, due to such an organization of structure, the proposed converter can develop an extremely high voltage-gain even at lower duty ratios. In addition, it has the advantage of lower switching stress across all power semi-conductive diodes. Furthermore, this paper describes the steady-state analysis and comparative features of the converter with existing recent literature. Finally, to validate theoretical analysis and test the feasibility and suitability of the proposed ultra-gain converter, the experimental results were observed by a 500 W fabricated prototype. [ABSTRACT FROM AUTHOR]

Light-emitting diodes (LEDs) are widely used in street lighting, landscape lighting, liquid crystal display (LCD) backlighting, healthcare, etc. As an important part of LED lighting products, LED driver plays a vital role in maintenance costs reduction, energy saving and lifetime prolongation. In this paper, a single-stage LED driver is proposed, which is integrated by a totem-pole bridgeless power factor correction (PFC) unit and several modular LCL-T resonant rectifiers. The totem-pole bridgeless PFC unit and the LCL-T resonant rectifiers are integrated by sharing switches, which can simplify the circuit and reduce the system cost. The output current can be regulated by applying the variable inductor control. Constant duty cycle and fixed switching frequency operation can be achieved as well. The operating principle and the performance of the proposed converter are analyzed in this paper. In addition, a precise parameter design method is proposed by considering the high-order harmonics. At last, an experimental prototype is established to validate the proposed parameter design and variable inductor control method. [ABSTRACT FROM AUTHOR]

In recent years, very high frequency (VHF) converter has attracted much attention. However, with rich parasitic parameters and complex resonance links, there are some great difficulties to the modeling of such systems. Taking the on-off controlled VHF resonant boost converter as an example, this paper presents an accurate modeling and analysis method that considers multiple parasitic parameters. First, the closed-loop VHF converter system is divided into a main network and a parasitic oscillation network. Then, based on the operation analysis, an equivalent circuit model characterized by a time-varying input voltage source and two variable duty-cycle controlled switches is proposed. It worth noting that both the time-varying input and the controlled switches take into account the influences of the parameters. Furthermore, the periodic approximate analytical solution of the output voltage in the on stage is obtained by using the equivalent small parameter method to the proposed circuit model. And then combining the solution of the parasitic oscillation network and on-off state switching conditions, the steady-state waveform of output voltage can be obtained quickly. Finally, a prototype with operating frequency of 21.44 MHz is built to verify the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

The dc-dc converters with high step-up DC-voltage gain play a vital role in integrating low voltage DC sources. Though several converter topologies are reported in the recent past, attempts have been made to reduce the components, especially the switching devices, passive elements, converter losses, etc., of the converter. A novel DC-DC converter topology, viz., single switched impedance network (SSIN)-based converter with n-stage is proposed in this paper. The operation of the SSIN based converter in continuous and discontinuous conduction modes are discussed. The effect of parasitic elements on DC-voltage gain and efficiency of the SSIN is carried out. The small-signal model of the SSIN converter is derived. The performance of the SSIN converter is compared with the similar converter topologies. The 500 W prototypes of the SSIN with n = 1 and n = 2 are fabricated, and the experimental results are presented in this paper. To improve the converter performance, SiC-based semiconductor devices are used. The SSIN converter with two-stage has low switch loss at 500 W load, improved efficiency during high power and high output voltage operation, the switch stress of Vo/2, etc. [ABSTRACT FROM AUTHOR]

This paper presents a new soft switching high voltage gain interleaved dc-dc converter with a three-windings coupled inductor for a fuel cell vehicle. Two interleaved and intercoupled boost cells are connected by the input parallel and output series (IPOS) configuration, realizing low input current ripple and high voltage gain simultaneously. All power switches can operate under soft switching conditions by only adding a simple auxiliary circuit composed of one auxiliary inductor and one power switch. Besides, the auxiliary inductor is coupled with the main inductors, which results in a rapid zero convergence of the auxiliary current and a small conduction loss of the auxiliary circuit. The operating principle, steady state characteristic, comparison with other converters, and parameter design are analyzed in this paper. Finally, the main characteristics of the proposed converter are verified by a 1-kW laboratory prototype. [ABSTRACT FROM AUTHOR]

A variable-switching constant-sampling frequency critical soft switching model predictive control (VSCS-MPC) method is proposed in this paper to improve the dynamic behavior, efficiency and power density of the DC/DC power converters. Firstly, this paper analyzes the boundary constraints of critical soft switching that are derived with the key parameters of the interlock time and threshold current for typical SiC and GaN devices. Then, the VSCS-MPC method is proposed for synchronous DC/DC converter. Both the current source load and resistive load converters are validated with the proposed MPC method. VSCS-MPC includes two controlling parts. First is the frequency controller to maintain the critical soft switching operation by adjusting the switching frequency based on the pre-defined boundary conditions with a constant sampling frequency. A discretized frequency controller is developed to improve the stability of the system by maintaining a fixed sampling frequency. Second part is the model predictive controller to track the output voltage/current and maintain critical soft switching during dynamic periods. The explicit optimization and oversampling methods are applied in the MPC controller to meet the high frequency demand. A large current ripple ($\triangle i_L$ $\ge$ 200 %) is introduced to achieve the critical soft switching and reduce the inductance. The switching losses are decreased by the frequency controller and the critical soft switching is maintained especially in dynamic periods due to the fast response of MPC. [ABSTRACT FROM AUTHOR]

The modular multilevel converter (MMC), owing to the presence of a large number of submodules (SMs) and energy storing elements, requires a large footprint and initial investment. To address these issues, this paper proposes the switched modular multilevel converter (SMMC). It consists of two major elements; the chain-links (CLs), consisting of cascade connection of SMs as in MMC, and the single-pole-triple-throw (SPTT) switches, which can be realized using either the T-type or NPC-type switch strings. The SMMC works on the principle of connecting all the phase-legs in series and their respective positions are mutually interchanged. It offers a compact structure as the SMs count is reduced to 33% of MMC, which results in a much lower energy storage requirement. Furthermore, it does not have inter-phase circulating current problem and hence the CL inductors can also be avoided. The SMMC structure, operating principles, control, and modulation schemes are explained in detail. A detailed comparison of SMMC with the other major existing converters is carried out to highlight the important features of SMMC. The efficacy of SMMC is validated using PSCAD simulation studies with a 19-level grid-connected SMMC model. A 3-phase 19-level SMMC laboratory prototype is developed to further validate its feasibility. [ABSTRACT FROM AUTHOR]

This paper investigates the Multilevel Current Source Converter (MCSC) STATCOM. It proposes a new method of modulation. The new modulation method produces less THD and di/dt at the terminals of the MCSC STATCOM when compared to the widely used Phase-Shifted Carrier SPWM (PSC-SPWM). To ensure the inductors' currents remain balanced, a Current Balancing Algorithm (CBA) is presented. The CBA does not require any controls. It relies on assigning optimum switching states to each CSC module in real-time. In addition, two control strategies are presented in this paper. The first one assumes the STATCOM to be a SISO. Therefore, it only requires one PI controller. However, the gains for the controller must be changed if the STATCOM was to transition from capacitive mode to inductive mode, or vice versa. The second control strategy overcomes this problem by implementing a TITO integral state feedback controller. The contributions of this paper are validated via simulation and experimental results. [ABSTRACT FROM AUTHOR]

A multi-level boost topology based on a flying capacitor is compared in this work with the hybrid, multi-level, partial power processing topology already presented in the literature for use as a highly efficient and compact dc/dc stage in 1500-V, two-stage, grid-connected PV systems. Different variations of the resonant stage of the hybrid topology are analyzed and compared in terms of losses, volume and complexity. Full multivariable optimization is conducted for the multi-level boost topology with different number of levels and for all the analyzed variations of the resonant stage of the hybrid topology. Appropriately rated new classes of 650-V and 900-V WBG devices are included in the optimization algorithm. It is concluded that due to the dominant conduction losses and gap in the voltage rating of the commercially available WBG devices between 650V and 200V, increase of the number of levels over 4 leads to the deteriorated loss and volume performances. All the analysis related to the resonant stage of the hybrid topology is confirmed by detailed and comprehensive measurements of two prototypes of 4kW of nominal and 7kW of maximal power. Additionally, all the loss models applied in the optimization algorithms presented in this paper are confirmed by detailed measurements, thermal calibration and finite element thermal simulations of the wide bandgap devices and inductor designs employed in this work. [ABSTRACT FROM AUTHOR]

The DC-DC converter for fuel cell vehicles should be characterized by high-gain, low voltage stress, small size and high-efficiency. However, conventional two-level, three-level and cascaded boost converters cannot meet the requirements. A new non-isolated DC-DC converter with switched-capacitor and switched-inductor is proposed in this paper, which can obtain high-gain, wide input voltage range, low voltage stresses across components and common ground structure. In this paper, the operating principle, component parameters design, and comparisons with other high-gain converters are analyzed. Moreover, the state-space averaging method and small-signal modeling method are adopted to obtain the dynamic model of converter. Finally, simulation and experimental results verify the effectiveness of the proposed topology. The input voltage of the experimental prototype ranges from 25 V to 80 V. The rated output voltage is 200 V and rated power is 100W. The maximum efficiency is 93.1% under rated state. The proposed converter is suitable for fuel cell vehicles. [ABSTRACT FROM AUTHOR]

Three-port converters with high voltage gain are desirable solutions for integrating renewable energy and energy storage devices into high voltage dc bus. A high gain three-port converter with soft switching is proposed in this paper, which can realize zero voltage switching for all switches and zero current switching for all diodes in various operating modes. Single coupled inductor is used to achieve high voltage gain and to reduce the voltage stress of switches so that switches with low on-resistance can be selected to reduce the conduction loss. In addition, the advantages of fewer components, higher voltage gain, and very low switch voltage stresses make the proposed converter more suitable for application in renewable energy systems than similar solutions. Various operating modes, performance analysis, design considerations, efficiency analysis, and control method of the proposed converter are discussed. A laboratory prototype with 30 V renewable energy source, 48 V energy storage device and 400 V output is designed to verify the performance of the proposed three-port converter. [ABSTRACT FROM AUTHOR]

On March 31, 2019, a 500 kV air-core, shunt reactor at a large generating station in BC Hydro was damaged shortly after four unit transformers were simultaneously energized from a 500 kV series and shunt compensated line source. Forensic investigations revealed that the controlled switching system, controlling the instant at which each breaker phase closes during energization to minimize inrush current, had failed. Uncontrolled closing led to under-damped, high-magnitude and sub-synchronous currents. Protection tripped and isolated the four transformers, followed shortly by shunt reactor protection tripping. Before the reactor could be isolated by circuit breakers, a damaging internal fault developed. This paper presents forensic investigation describing sequence of events leading up to reactor damage and shares the lessons learned with the peer utilities having similar installations.    [ABSTRACT FROM AUTHOR]

This paper presents the development of a Class-D full-bridge zero-voltage switching (ZVS) inverter, applicable to wireless power transfer (WPT) systems, operating at 13.56 MHz switching frequency with dynamic dead-time control (DDTC). Resonant-coupled WPT systems are being designed at ultrahigh switching frequencies to reduce the size of the wireless link and the passive components. Maintaining ZVS while controlling the output power delivered to a fixed or variable load is one of the major challenges of designing inverters at multi-MHz switching frequencies. DDTC is the approach deployed in this paper to sustain soft switching of a Class-D full-bridge inverter over the full range of output power while regulating the input dc bus voltage. Simulation results are presented to show that dynamically controlling the dead-time during input dc bus voltage variations reduces switch-node voltage overshoot, prevents large current spikes in the switching devices, and reduces associated high switching loss. Practical results obtained show that DDTC reduces switch-node voltage overshoot, increases the inverter efficiency, and reduces the steady-state temperature of the inverter during output power regulation. [ABSTRACT FROM AUTHOR]

This paper presents a unified second-stage LC filter applied in the three-state switching cell buck–boost converter, which provides current and voltage with low ripple and low noise. The unified second-stage filter promotes a reduction in the number of devices while maintaining the filtering performance of the converter, with second-stage LC filters at the input and at the output. Moreover, the unified filter, when associated with a three-state switching cell buck–boost converter, allows a size reduction of filter devices, especially for designs with duty cycle range around 1/2. Furthermore, the unified filter arrangement provides nondissipative clamping of switching devices and reduce the system order when compared to the converter with second-stage LC filters. In this paper, the static and dynamic characteristics of the proposed converter in continuous conduction mode (CCM) are reported. Experimental data were obtained from a laboratory prototype with an input range of 32 $\sim$ 72 V, constant output of 48 V, a load of 150 W, and switching frequency of 45 kHz. The measured efficiency for the rated load was 97% for maximum input voltage. A comparison of the size and performance of the proposed filter with the topology that uses second-stage LC filters at the input and at the output is also presented. [ABSTRACT FROM AUTHOR]

In this paper, many impedance-source inverters with coupled inductors have been investigated to obtain a high step-up boost ratio. However, the leakage inductors in these topologies induce great voltage spikes at the dc link, which will increase the voltage stress of switches. Thus, the power level of inverters is limited. Furthermore, the efficiency of the inverters can be degraded by the losses associated with leakage inductors. To address abovementioned issues, this paper proposes a family of low-spike high-efficiency Y-source inverters. The proposed inverters have the ability of eliminating voltage spikes at the dc link and recycling the leakage energy via the additional diode and capacitor. In order to show the excellent characteristics of the proposed topologies, this paper compares the performances of the proposed inverters and the improved-Y-source inverter in many aspects. Simulation and experimental results have verified the abilities of the proposed inverters. [ABSTRACT FROM AUTHOR]

Various methods have been presented in the past to emulate the electrical behavior of modular multilevel converters (MMCs). To meet the demands for the reliability aspect study of MMCs, this paper proposes a viable setup to emulate the thermal behavior and to investigate its feasibility for reliability testing and thermal model validation of the power modules in the MMC. The proposed mission profile emulator has three distinctive features: 1) capable of emulating and measuring the thermal stresses of power modules; 2) capable of implementing practical switching profile as a full-scale MMC; and 3) having significantly reduced requirement for dc power supply compared to existing setups used for electrical studies. Theoretical discussions, and simulations as well as the experimental results are presented to demonstrate the capability of the mission profile emulator both electrically and thermally. Moreover, this paper is accompanied by a video demonstrating how to measure the junction temperature of the power devices using the optical fiber and the thermal camera. [ABSTRACT FROM AUTHOR]

With the rapid development of photovoltaic and fuel cell stacks, high voltage gain converters are urgently demanded. Conventional boost is limited by the exaggerated duty cycle, it is impossible to obtain a high voltage gain while ensuring efficiency. Therefore, a zero-voltage switching (ZVS)-modified SEPIC converter that combines a voltage multiplier cell with traditional SEPIC is proposed in this paper. With detailed parameters design process, this presented converter works at zero voltage switching (ZVS), while obtaining high voltage gain without extremely high duty cycle. Besides, voltage stress is also reduced and low-voltage component with lower parasitic parameters can be used, thus efficiency is maintained. In order to further improve the power density, an integrated inductor scheme is adopted in this paper without changing intrinsic working states of the two inductors. A 36-W prototype is built, and experiments are conducted to verify the advantages of the proposed converter. The efficiency is up to 91.5% at full load. [ABSTRACT FROM AUTHOR]

This paper proposes a soft-switched modulation technique with synchronous rectification for an isolated single-stage single-phase matrix-type dc–ac converter. The dc side consists of a full bridge inverter, and the ac side is a 2×2 matrix converter-based cycloconverter. The proposed unipolar modulation strategy provides zero current switching/zero voltage switching (ZVS) for the ac side devices and ZVS-on for the dc side devices. It also allows natural commutation of the current flowing through the secondary side leakage inductor of the isolation transformer and the grid inductor during unity power factor (UPF) condition, thus eliminates the requirement of snubber circuit. An improved soft-switched flyback-based regenerative snubber circuit is also presented for non-UPF operation. Proposed snubber circuit recycles the energy stored in the snubber capacitors in every switching cycle. A guideline to design snubber circuit along with a comparative study is discussed in this paper. Performance of the proposed hybrid modulation technique is evaluated in an SiC mosfet based 1.2-kW dc–ac converter prototype. A detailed analysis of the converter performance has been presented in this paper considering the circuit non-idealities. [ABSTRACT FROM AUTHOR]

This paper presents a novel integrated-stage light-emitting diode (LED) driver based on Flyback and resonant converters. The Flyback converter realizes power factor correction in the discontinuous conduction mode. The resonant converter is operated as a dc–dc converter to support the LED loads. Moreover, the resonant converter can clearly decrease the drain–source voltage of the active switch and exhibits zero-voltage-switch characteristics. Therefore, a cost-effective MOSFET can be chosen as the main control component that can decrease the cost of the whole system. Compared to a single-active-switch converter (such as Class-E converter), the number of passive components in the resonant converter can be limited to four. Therefore, the power density of the system can be improved drastically. In this paper, a 100-W prototype is presented under the experimental condition to validate the proposed integrated-stage LED driver. [ABSTRACT FROM AUTHOR]

In this paper, a new dc–dc high voltage gain converter with low-voltage stresses on switches and diodes is proposed. Even though, in the topology of the proposed converter there are not any coupled inductors and transformer utilized, the voltage conversion ratio of the proposed converter is considerable in comparison to its conventional types. Also, two switches of the proposed converter provide longer charge time for two inductors which make the proposed converter capable of providing high voltage gain without preselecting extremely large duty cycles. In addition, the number of power circuit components of the proposed structure are few and the voltage stresses on semiconductor elements are low. In this paper, theoretical analysis of the proposed converter for each operating mode is presented and the voltage gain, voltage and average current stresses of elements, maximum input current ripple, efficiency and equations of critical inductances are calculated. Moreover, to verify the capability of the proposed converter, it is comprehensively compared with other similar recently presented high voltage gain boost converters. Finally, an approximately 12 V/380 V and 520-W prototype of the proposed converter is implemented in laboratory to demonstrate its practical performance, then, the experimental results reconfirm each other and theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper presents bidirectional grid-connected modular multilevel converters (MMC) with direct digital control and division-summation processes to achieve power-injection and rectification functions. A direct digital control is developed to track current references, regulate dc-bus voltage and cell voltage, and balance the upper and lower dc-bus voltages. It can accommodate wide filter-inductance variation and take care of source voltage harmonics to achieve tight current tracking and low distortion output current. Based on the power-balance principle, the commands of arm currents can be determined directly. In this paper, the MMC configuration is introduced first, and then the control laws for current tracking and voltage regulation are derived in detail. Experimental and simulated results obtained from two 50 kW MMCs operated in power-injection and rectification modes have verified the analysis and discussion. [ABSTRACT FROM AUTHOR]

This paper introduces a novel modeling approach that allows to obtain fast simulations of pulsewidth-modulated dc–dc switched-mode power supplies (SMPS). The proposed methodology combines the use of precise switched models during transient evolutions and averaged models during steady-state or slowly varying conditions. In that way, the resulting mixed modeling approach enables to obtain the detailed switching behavior of SMPS in the context of long-term simulations. The commutation between models is automatically performed in runtime by an algorithm that detects the transient or slowly varying condition according to the evolution of some model variables. When the precise switched model is used, the mentioned algorithm also adjusts the averaged model parameters so that its results are accurate irrespective of the operating point. This paper also describes the implementation of the methodology in the Modelica language and reports simulation experiments showing that the results are as accurate as those obtained using precise switched models, but several times faster. [ABSTRACT FROM AUTHOR]

This paper presents an interleaved boost converter with a bifold Dickson voltage multiplier suitable for interfacing low-voltage renewable energy sources to high-voltage distribution buses and other applications that require a high-voltage-gain conversion ratio. The proposed converter was constructed from two stages: an interleaved boost stage, which contains two inductors operated by two low-side active switches, and a voltage multiplier cell (VMC) stage, which mainly consists of diodes and capacitors to increase the overall voltage gain. The proposed converter offers a high-voltage-gain ratio with low voltage stress on the semiconductor switches as well as the passive components. This allows the selection of efficient and compact components. Moreover, the required inductance that ensures operation in the continuous conduction mode (CCM) is lower than the one in the conventional interleaved boost converter. The distinction of the proposed converter is that the inductors’ currents are equal, regardless of the number of VMCs. Equal sharing of interleaved boost-stage currents reduces the conduction loss in the active switches as well as the inductors and thus improves the overall efficiency, as the conduction power loss is a quadratic function. In this paper, the theory of operation and steady-state analysis of the proposed converter are illustrated and verified by simulation results. A $\text{200-W}$ hardware prototype was implemented to convert a $\text{20-V}$ input source to a $\text{400-V}$ dc load and validate both the theory and the simulation. [ABSTRACT FROM AUTHOR]

A high-frequency high voltage gain discontinuous conduction mode coupled-inductor boost LED driver based on planar component is presented in this paper. GaN switch is adopted with lower conducting resistance and higher switching speed. Zero voltage switching (ZVS) is achieved at the same time to reduce high switching loss caused by high switching frequency. Compared with the previous work, the voltage gain is higher and efficiency is higher because of ZVS. This paper focuses on high efficiency; therefore, resonant gate driver is adopted and efficiency is increased by 0.6%. In terms of the coupled-inductor, planar component is used and parameter optimization is also proposed to realize lower loss, including wingding loss and fringing loss caused by the air gap. A 500 kHz 36 W prototype has been designed to demonstrate theoretical analysis. In addition, comparison of drive loss between the resonant gate driver used in this paper and conventional driver implemented by Si8271 is made, revealing advantages of the resonant driver. Obtained efficiency was up to 92.1% at full load. [ABSTRACT FROM AUTHOR]

The use of electronic equipment and other dc-compatible appliances in homes and offices is increasing at a very fast rate, as well as the distributed generation of energy. These two statements will most likely trigger, in a near future, the adoption of district-scale dc grids, connecting dc microgeneration plants and consumers, in an effort to cut the number of conversion steps required to deliver power to dc appliances. DC–DC converters will be fundamental in these systems, allowing the establishment of several voltage levels. The reliability of these converters plays a critical role, ensuring service continuity of the loads connected to them. With the increment of reliability in mind, this paper proposes a simple yet effective open-circuit fault diagnostic method suitable for interleaved dc–dc boost converters, but equally functional for other dc–dc converter topologies. The improvements introduced in this paper greatly simplify the diagnostic action, while making the correct diagnostic of faults independent of the switching duty cycle. Moreover, an alternative reconfiguration scheme is proposed to mitigate the adverse impacts of such faults. To prove the effectiveness of these strategies, a three-phase interleaved boost converter prototype was used in the experiments. [ABSTRACT FROM AUTHOR]

In this paper, a series-capacitor-based interleaving buck power factor correction (PFC) converter is proposed, the intermediate energy storage capacitance of which is operated at discontinuous capacitor voltage mode (DCVM), and automatic power factor (PF) correction for this converter is obtained. Moreover, the voltage across the series capacitor of the proposed PFC converter is clamped at the input voltage, and thus peak voltage stress existed in the traditional DCVM buck PFC could be relieved. By effectively regulating the charge/discharge time for the series capacitor, ultrahigh step-down conversion ratio of the proposed converter is achieved, the conversion ratio of which is independent of the duty cycle and only related to the switching frequency and circuit parameters. Therefore, high PF can be obtained due to very narrow deadtime of the input current. Meanwhile, the proposed PFC converter can realize the soft turn-on of part power switch and soft turn-off of part power diodes. In addition, comparing with the traditional discontinuous inductor current mode PFC, the input current of the proposed PFC converter is continuous so that the peak value and root-mean-square value of input current can be reduced. The operational principle, performance analysis, and parameter design principle are given in this paper. The analysis results show that the PF and total harmonic distortion are also independent of the duty cycle. Finally, a 220-Vac input, 60 W/15 V output experimental prototype is built to verify the validity of the theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper proposes a new class of topologies of single-stage high-frequency ac-link power converters, which is capable of providing both voltage step up/down within a wide frequency and voltage ranges. The proposed family, which supports bidirectional power flow, can interface various single/multi-port dc and/or single/multi-phase ac systems to provide dc–dc, dc–ac, ac–dc, or ac–ac power conversion. In this family of converter, which offers a very modular structure, a small inductor that forms the link exchanges power entirely or partially between the source and load. The proposed family can function in buck, boost, and/or buck–boost modes of operation, and a combination of these modes of operation is also feasible. In comparison to the parallel inductive four-quadrant link converters, the proposed family features a significantly reduced link peak current, reduced switch ratings, and reduced total number of power switches. These features enhance the efficiency, reduce the total cost, and increase the power density of the system. In order to further improve the overall efficiency of the system, minimize the current/voltage stress over all utilized semiconductor devices, and lower electromagnetic interference (EMI), a small capacitor is placed in parallel with the link inductor to realize soft-switching operation for the proposed configurations. Moreover, the proposed converters have the potential to incorporate a lightweight single-phase high-frequency transformer for electrical isolation. The proposed circuit topologies prevent reverse recovery issues and eliminate losses corresponding to body diodes of power switching devices via utilizing power switches in conjunction with external fast recovery diodes. The proposed family offers a very high level of reliability owing to its immunity from short circuit of input and output terminals and open circuit of the link inductor, which may occur in other power converters due to commutation problem resulting from a short deadtime or an overlap time between switches, unwanted control command, delay in electronic circuits, or EMI noise's misgating on or off, in addition to the absence of electrolytic capacitors in the power circuit. A control approach is also developed to regulate input and output currents in one stage of power conversion. A detailed theoretical analysis, operation, design methodology, and control strategy of the proposed family are provided in this paper, and the effectiveness and performance of the proposed converter family are verified via simulation results and experimentally. [ABSTRACT FROM AUTHOR]

Switching behavior analysis is an indispensable step for evaluating the steady-state performance of a bidirectional dc–dc converter and a prerequisite for soft-switching modulation design. For dual-bridge series resonant dc–dc converters (DBSRCs), the commonly used fundamental harmonic approximation (FHA) does not usually provide predictions accurate enough for reliable analysis and design. This paper discloses the exact closed-form solution for the zero-voltage switching (ZVS) operation conditions of DBSRCs for the most general case, in which all modulation quantities—i.e., phase shift, duty cycles, and switching frequency—are included. The proposed approach relies on a geometrical analysis of the converter state-plane trajectory, and allows us to analytically predict the ZVS or hard-switching state of any switch and for any given converter operating point. By inherently capturing the effects of all tank harmonics, the model disclosed in this paper shows higher accuracy than the conventional FHA-based approach, and translates into a practical tool for ZVS prediction and optimization at the converter design stage. Based on the derived analytical results, switching behavior of DBSRCs with minimum rms current trajectory (MCT) modulation is investigated, and an effective design choice of resonant-to-switching frequency ratio is presented, which contributes to reduced switching losses and enhanced efficiency. Furthermore, a variable frequency modulation scheme is formulated, achieving ZVS operation of all transistors over a wide input/output voltage range and efficiency improvement versus MCT technique. The analysis and conclusions are validated via extensive experimental tests on a 700 W DBSRC prototype. [ABSTRACT FROM AUTHOR]

In this paper, a new class of bidirectional partial-resonance power converters is presented. The proposed family can be configured to interface single- or multi-port dc, single- or multi-phase ac systems at input-side and/or output-side. The proposed family offers a very modular structure, which can lead to cost reduction from a common designed module. In this converter, which accomplishes power conversion in a single stage, a small inductor placed in series with the input and output switch-bridges forms the link. This small link inductor is responsible for transferring power between different ports of the system. The proposed topologies can operate in buck, boost, and buck–boost modes of operation to step up and/or step down the voltage. In buck–boost mode of operation, the converter is controlled such that the power is entirely transferred through the link inductor; whereas, in buck or boost modes of operation only a fraction of the power is transferred through the link inductor, and the remaining power is directly transferred from input phases to the output phases. Galvanic isolation, which is typically a prominent factor contributing to power density of a converter, can be provided by means of a compact and lightweight single-phase high-frequency transformer added to the link. In comparison with earlier generations of partial-resonance inductive-link power converters, in the proposed converter, the level of link peak current and consequently power-loss, as well as voltage and current stress of switches are dramatically decreased. A very small film capacitor can be placed in parallel with the link inductor to facilitate zero-voltage-switching (ZVS) operation for all the switches/diodes. Apart from increasing the overall efficiency, minimized dv/dt stress and improvement in power density are achieved by adding the link capacitor. The proposed converter employs four-quadrant switches, i.e., bidirectional-conducting bidirectional-blocking switches, and charges the link inductor in both positive and negative directions in each cycle. In view of this, better utilization of the link inductor and lower total harmonic distortion (THD) are offered. Furthermore, two distinct switching algorithms are developed for the proposed family of converters. In this paper, the detailed behavior of the proposed family is investigated analytically, and simulation and experimental results are presented to evaluate the performance and effectiveness of the proposed converter. A low-power proof-of-concept prototype with input voltage of 59 V/161 V, load voltage of 178 V/73.5 V, maximum switching frequency of 4.9 kHz/3.65 kHz at 215 W/450 W in a step-up/step-down operation is considered for the experimental verification. [ABSTRACT FROM AUTHOR]

This paper studies the high power density bidirectional dc–dc converter with interleaving, soft-switching, and near critical conduction mode (near-CRM) operation. Systematic design and control methods are proposed to enhance the effectiveness of passive currents balancing between multiple interleaved phases without using individual phase current feedbacks. This paper first analyzes the zero voltage turn-on operation, including the turn-off energy diversion by the added snubber capacitor and the turn-off resonance models. Second, the intrinsic inverse co-relation between the phase current deviation and the resulting effective duty cycles variation is quantitatively formulated and modeled as a closed-loop mechanism that balances the currents passively. Then, the design constraints of the system parameters including the snubber capacitance, dead time, and valley currents of the near-CRM mode are formulated to guarantee the effectiveness of counteracting the current unbalance. Finally, a variable switching frequency control is proposed to actively control the valley current and maintain the current balancing effectiveness throughout the operating range. An IGBT-based 20-kW three-phase interleaved prototype with the maximum efficiency of 99.1% is constructed to verify the proposed design and control methods. [ABSTRACT FROM AUTHOR]

This article develops a series of improved Z-source dc–dc converters to realize additional voltage pumping and high power density through two propositions. Proposition 1 develops two improved positive- and negative-connected Z-source dc–dc converters (IPZSC and INZSC), using the same number of components as in the existing voltage pumping Z-source converter. Based on Proposition 1, Proposition 2 proposes four novel embedded Z-source dc–dc converters (EZSCs) by placing the source in a specifically designed position, which realizes lower voltage stresses across capacitors. Various technical aspects of the proposed EZSCs, including operations, power losses, and small signal stability analyses are detailed in this paper. Besides, comparisons between the proposed series of improved Z-source dc–dc converters and other existing Z-source dc–dc converters are thoroughly made to demonstrate the better performance of the EZSCs. Finally, experiments are conducted to well validate the effectiveness and superiority of the proposed converter circuits. [ABSTRACT FROM AUTHOR]

The extra-LC auxiliary-resonant-snubber-based converter (ELCARSC), as a soft-switching converter, has the advantages of low switching loss, low electromagnetic interference noise, and low-output distortion caused by the dead-time effect. However, the dead-time effect is still the main problem in a high-precision application. Besides, the traditional control and compensation methods rely on the accuracy of the circuit parameters, especially the junction capacitance, thus resulting in compensation error. Therefore, this paper proposed a novel high-precision control method through modulating the initial resonant current to eliminate the dead-time effect of ELCARSC. The method does not need complicated online calculation and reduces the dependence on the accuracy of the circuit parameters, especially the influence of the junction capacitances of the switches. In this paper, the dead-time effect of the ELCARSC is analyzed. The output voltage error with the conventional variable-timing control method is analyzed. Subsequently, the proposed modulated initial resonant current control is introduced. Finally, a prototype was developed that verified the effectiveness of the control method. The quality of the output current and voltage is improved by utilizing the proposed control method. However, the peak current of the auxiliary switch is increased. [ABSTRACT FROM AUTHOR]

This paper has introduced two important indexes, turn-off surge voltage (TSV) on power switch and peak positive pole potential (PPPP) of storage batteries, which can be used to evaluate switching transient process of high-voltage energy storage system. Research on them is of great significance to power switch choice and high-voltage isolation design in engineering applications. Power switch response process at the turning off moment and transient process in freewheel stage have been analyzed by the established small-signal model of single power switch; then, a power switch test platform for hybrid energy storage system was built to verify it. Taking pulsed-power supply charging device with a novel inductor of low resistance and high inductance as a research object, this paper has analyzed dynamic process of the TSV and the PPPP at the turning off moment through establishing state space model of the whole system. Comparison shows that the numerical curves match the simulated curves well. Finally, the exactness of the employed model has been further verified in two pulse capacitor charging experiments. [ABSTRACT FROM AUTHOR]

This paper presents two high-voltage direct-current circuit breakers that have the capability of interrupting a short-circuit current within several milliseconds. They consist of a current-limit inductor, a current-control inductor, one or two mechanical switches, and a multilevel converter with phase-shifted-carrier pulsewidth modulation. The two breakers can commutate an almost zero current from the main branch to the auxiliary branch. This paper proposes an original breaker with low-voltage and high-voltage mechanical switches connected in series, followed by a simplified breaker with a single high-voltage mechanical switch. Finally, this paper includes experimental verification by two slightly different downscaled breakers rated at 300 Vdc and 150 Adc, as well as confirmation of an actual original breaker by circuit simulation using the “PSCAD/EMTDC” software package. [ABSTRACT FROM AUTHOR]

Inductor current is an important feedback parameter in synchronous buck converters (SBCs). It is used for overcurrent protection, current sharing among interleaved modules, and current-mode feedback regulation, among others. While implementing a digital controller, inductor current is sensed and fed into the controller through a high sampling frequency analog to digital converter (ADC). As the switching frequency of the converter becomes higher, the need for an even higher sampling frequency ADC also goes up, which is a distinct disadvantage in terms of the overall cost. This paper discusses a simple current estimation technique that avoids use of any expensive current sensor and high sampling frequency ADCs. The paper shows that in a buck converter, inductor current can be estimated by tracking the width of the switch node voltage. Implementation and limitations of the proposed current estimation scheme are discussed in detail. The proposed method is validated using a 3.3 V–15 A SBC prototype and results show the estimation technique is accurate within 5% with a converter switching frequency of 800 kHz. In order to prove the effectiveness of the technique in feedback regulation, the current estimation technique is used to implement average current mode and hysteretic current mode control on a SBC. To prove the effectiveness of the proposed current estimation scheme, it is used in closed-loop control of the SBC to verify the dynamic responses, such as start-up transient, step change in load, and reference. [ABSTRACT FROM AUTHOR]

This paper presents a new digital control scheme for active virtual ground-bridgeless PFC (AVG-BPFC), which is able to obtain an optimized solution between the system efficiency and electromagnetic interference performance in the PFC stage. However, a resonant characteristic is generated from the input LCL filter structure of the converter. In addition, there is a phase difference between two inductor currents which also leads the controller design in the AVG-BPFC to become challenging, especially on the system stability and current quality. Thus, a triple loop control's architecture together with an integrated state machine is proposed as the control methodology of the AVG-BPFC. Under the simple control structure in the digital platform, a stable system is achieved together with a precise grid current tracking function. Such control scheme was implemented digitally on a 1.5 kW prototype. In this paper, theoretical models of the whole system were analyzed and the system performance was successfully verified in both steady state and transient state conditions. The experimental results show a good agreement with the theoretical knowledge. [ABSTRACT FROM AUTHOR]

This paper presents a high-gain modular input-parallel output-series dc-dc converter for photovoltaic integration with medium-voltage dc grids. A new full-bridge zero-current-switching (FB-ZCS) converter proposed in this paper is used as a fundamental building block. Existing FB-ZCS converters utilize transformer leakage inductance and a shunt-connected resonant capacitor for achieving smooth resonant current commutation and ZCS. The shunt-connected capacitor requires dedicated charging interval in every switching cycle and stores full-load-rated resonant energy at all load/input conditions, resulting in significant duty-cycle loss. Moreover, it suffers from energy leakage through transformer winding and requires overrating. All these factors adversely impact the operation range of the converter, which is important for achieving a wide maximum power point tracking range. Novel improvements in the proposed converter include minimization of duty-cycle loss and resonant capacitor leakage and the realization of the current-adaptive resonant energy storage mechanism, without using additional switches or auxiliary circuits. Operation of the proposed converter is presented and validated with simulation and experimental results. [ABSTRACT FROM AUTHOR]

In data center and telecommunication power supplies, the front-end dc–dc stage is required to operate with a wide input voltage range to provide hold-up time when ac input fails. Conventional LLC converter serving as the dc–dc stage is not suitable for this requirement, as the normal operation efficiency (at 400 V input) will be penalized once the converter is designed to achieve high peak gain (wide input voltage range). This paper examined the operation of the LCLC converter and revealed that the LCLC converter could be essentially equivalent to a set of LLC converters with different magnetizing inductors that are automatically adjusted for different input voltages. In nominal 400 V input operation, the LCLC converter behaves like an LLC converter with large magnetizing inductor, thus the resonant current is small. In the hold-up period, when the input voltage reduces, the equivalent magnetizing inductor will reduce together with switching frequency reducing, thus the converter achieves high peak gain. In this paper, a new design methodology is also proposed to achieve optimal utilization of the two resonant capacitors for high power application. To verify the effectiveness of the LCLC converter for hold-up operation, comprehensive analysis has been conducted; a detailed step by step design example based on capacitor voltage stress is introduced; an experimental LCLC prototype optimized at 400 V, with input voltage range of 250–400 V and 12 V/500 W as output has been presented. [ABSTRACT FROM AUTHOR]

A single-stage three-phase ac–ac converter benefiting from a high-frequency alternating link voltage is proposed in this paper. In this converter, a very small film capacitor can transfer the energy from the input to the output, owing to the high-frequency alternating voltage of the link. This eliminates the need for large electrolytic capacitors that are typically used in dc-link ac–ac converters. Moreover, a compact high-frequency transformer at the link can replace the bulky low-frequency transformers, in case isolation is required. These features increase the power density as well as reliability of the proposed converter in comparison with the conventional dc-link converters. The number of required switches in the proposed converter is 12, which is less than the number of switches needed in matrix converters, leading to lower switching and conduction losses. Despite being single-stage, the proposed ac–ac converter is capable of both stepping up and stepping down the voltage and also frequency transformation. This eliminates the need for using cascaded power converters. In this paper, the operation principles of the proposed ac–ac converter are investigated, and variable switching frequency and fixed switching frequency control methods for operating this converter are introduced. The performance of the converter is verified through simulation and experiment. [ABSTRACT FROM AUTHOR]

In this paper, a new structure for a nonisolated boost dc–dc converter is proposed. The proposed converter generates higher voltage gain than some conventional nonisolated boost dc–dc converters. In this paper, the voltage and current equations of the elements and voltage gain in continuous conduction mode and discontinuous conduction mode are extracted. Then, the critical inductance converter is extracted and the current stresses in the switches are calculated. To achieve high voltage gain, a generalized structure based on the proposed structure generates for dc–dc converters. Meanwhile, the root mean square current relations of devices are obtained for an extended structure. Finally, the results of PSCAD/EMTDC software and laboratory prototype are used to reconfirm theoretical concept. [ABSTRACT FROM AUTHOR]

In the paper by Patra et al., a single-inductor multiple-output switcher was presented to produce buck, boost, and inverted outputs simultaneously. Unfortunately, this study showed some unexpected mistakes, especially in state-space equations and in the calculation of output voltages. The objective of this note was to provide correct analysis and rectify the errors in this paper. Some tables and equations have been modified that were present in the initial draft of this paper. The obtained parameters in this work could be an effective supplement and extension for the original work in the paper by Patra et al. [ABSTRACT FROM AUTHOR]

Soft magnetic powder cores with their high saturation flux density and low core loss are excellent alternatives for filter inductors in inverter-based applications. However, their nonlinear current-dependent inductance characteristics pose a challenge for control of grid-connected inverter with LCL filter. In this paper, the variable inductance conundrum is discussed and a modified direct digital control method based on a variable-structure inductance estimation model that takes into consideration wide nonlinear variation in both inverter- and grid-side inductances is proposed. The proposed method is shown to have better grid-voltage harmonic rejection and improved stability margins. However, investigation of stability which is conventionally based on nominal values of filter inductors cannot predict instabilities over the entire range of inductance variation. Hence, a parametric approach to conventional stability methods with a parameter space defined by variation in actual and estimated inductance is explored in this paper. The effect of line impedance on stability is also investigated with impedance-based stability criterion by considering line inductance as an additional dimension in the parameter space. A pattern in stability margins is observed due to inductance variation, with inductance at its minimum being most vulnerable to instability. Experimental results measured from a 5 kW single-phase grid-connected inverter with various LCL filters have verified the feasibility of the proposed control method. The experimental results also match the analytical results with reasonable accuracy. [ABSTRACT FROM AUTHOR]

This paper proposes an improved zero current detection for critical conduction mode (CRM) control, which can compensate the input current distortion caused by the signal propagation delay and the existence of the negative resonance current. A unified variable on-time calculation method is also proposed to unify the formulas under the zero-voltage-switching condition and the valley-switching condition. Since these two methods are dependent on the boost inductance and device junction capacitance, which may be different from the nominal values, effort is needed to compensate the deviation on these two parameters. In this paper, an online monitoring method is proposed to compensate the numerical deviation. The proposed method only needs to sense the input voltage, output voltage, and the reverse flow time of the inductor current, leading to a high power quality in the entire input and load conditions. The experimental results of the proposed methods are demonstrated on a 200-W GaN-based CRM boost power factor correction prototype. With the proposed methods, the input current total harmonic distortion is only 0.78% at 110 VAC input with full load and 2.1% at 220 VAC input with full load. [ABSTRACT FROM AUTHOR]

This paper discusses a novel methodology to increase the voltage droop compensation range in generalized solid-state bipolar high-voltage Marx modulators with one resonant stage. To maintain the modularity characteristic of bipolar Marx modulators, the imbedding of additional resonant stages is not straightforward. Nevertheless, this paper proposes to add a second resonant stage to the already existing resonant-type voltage droop compensation stage. This second stage increases the voltage droop compensation percentage of a generalized solid-state bipolar Marx generator. The compensation of the bipolar pulse voltage droop is now achieved by adding two auxiliary synchronous compensation resonant voltages, to the output capacitive decaying voltage. Simulation and experimental results are presented for six Marx plus two resonant stages, 16% voltage droop, with 3-kV pulse amplitude, 100- $\mu \text{s}$ pulsewidth, 40-ms relaxation time, and 10-Hz pulse repetition rate. [ABSTRACT FROM AUTHOR]

Multioutput converters with single input source are currently studied as an alternative to conventional dc–dc topologies in order to improve power density in low-power multiload applications. This paper reviews three different ways in which a boost topology can be customized to supply multiple outputs. The first way uses a charge-sharing approach using individual switches to distribute inductor energy to different capacitors. The second method of creating a multiport converter (MPC) combines two converters with similar front end to generate two outputs using only one controlled switch. Using this method, a boost converter can be combined with single–ended primary–inductor converter (SEPIC), Cuk, and current source converter topologies. The third method uses time multiplexing of switches to produce two regulated ports and is referred to as switched-boost action. This method uses relatively less number of switches and allows regulation and control of all the outputs. Practical utility of switched-boost action based MPC is reported in this paper. This switched-boost MPC is applied to a renewable power converter system to interface a solar panel, a battery, and home loads to produce a 12-V and a 48-V bus. The 12-V bus is interfaced to battery and capable of optimally charging the battery in constant current–constant voltage (CC-CV) mode. The converter is demonstrated to operate with solar panel as it supplies a 12-V battery and a 48-V load bus. When the solar power is not available, the converter automatically goes into a mode in which the 12-V battery supplies the loads on the 48-V bus. [ABSTRACT FROM AUTHOR]

This paper proposes a new dc–ac converter with a reduced number of semiconductor switches and gate drive and control circuit components. A salient feature of this inverter is its pure sinusoidal line-to-line voltages with no need for output filter. Also, the proposed inverter improves the voltage utilization factor of the input dc supply compared to the four-switch three-phase inverter (first best topology in the literature from the number of switches point of view) and standard six-switch inverter with sine pulsewidth modulation. The proposed inverter is capable of operating with a wide range of output voltages from zero to the full value of the dc input voltage by appropriately altering the instantaneous duty cycle. A three-phase universal inverter with only three power switch has been proposed in this paper for the first time ever, to our knowledge. For the purpose of providing a good compromise between fast transient response and stability, a model predictive controller is proposed. All the design expressions have been derived. A comparison with other dc–ac converters is given to show the merits of the proposed converter. Finally, satisfactory circuit operation is confirmed by experimental results from a laboratory prototype. [ABSTRACT FROM AUTHOR]

In this paper, a new nonisolated high step-down dc–dc converter with ultrahigh step-down conversion ratio is proposed. Advantages of the proposed converter are high step-down ratio, extended duty cycle, reduced switching losses by a converter operation under zero-voltage switching (ZVS) conditions, reduced reverse reco-very losses of diodes by achieved zero-current switching turn-off condition, and reduced voltage spikes by the inherent active-clamping structure of the converter. In this converter, series capacitors and coupled inductors have been used in power path to achieve the low voltage gain and extended duty cycle. By the inherent active-clamping structure of the proposed converter, the leakage inductance energy is totally recovered in the output; therefore, the high voltage spike across the semiconductor devices is suppressed. The switches of the proposed converter can operate under ZVS conditions, which cause reduced switching losses and improved efficiency. In this paper, the converter operating modes are discussed, and a prototype circuit is implemented. Experimental results are presented to verify the theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper proposes a high-efficiency single-phase T-type boundary conduction mode (BCM) microinverter. The conventional full-bridge BCM microinverter has achieved zero voltage switching (ZVS) and thereby improved the efficiency, but it suffers from high switching losses under light load conditions. The proposed T-type BCM microinverter reserves ZVS and uses a multilevel technique to further decrease the switching losses. The BCM operation with multilevel technique will have too low switching frequency when the grid voltage approaches half of the dc link voltage. To solve this problem, this paper adopts a third operation mode for the T-type switching leg to maintain the switching frequency above a minimum value. The corresponding mode transitions are also detailed to ensure a smooth operation. Because of the turn-offdelay of the freewheeling transistor, the actual lower current boundary deviates from the programmed one, which will distort output current. To address this issue, this paper also proposes a boundary compensation method. A prototype has been built for performance verification, which can test both full-bridge and T-type topology. Compared with the full-bridge BCM microinverter, the proposed T-type BCM microinverter has a higher efficiency over the whole load range. [ABSTRACT FROM AUTHOR]

In this paper, a new soft-switching bridgeless single-phase power factor correction (PFC) converter is presented and analyzed. Employing an auxiliary switch, the input current dead angle that is the main drawback of the existing buck-type PFCs is omitted, and thus, the power factor (PF) is improved, which is the main contribution of the paper. Proposed PFC converter operates under discontinuous conduction mode (DCM) and draws sinusoidal input current from power supply inherently. All switches and diodes are turnedonandoffunder soft switching, which leads to low switching losses and elimination of diode reverse recovery problems. Also, minimum numbers of semiconductor devices are in the power flow path that reduce the conduction losses. A 120-W laboratory prototype is implemented and experimental results verify the validity of theoretical analysis and show efficiency of 92.1%. In addition, total harmonic distortion (THD) of 3.3% is achieved and the input current harmonics complies with IEC61000-3-2 Class D requirements. [ABSTRACT FROM AUTHOR]

Soft-switching techniques of transformerless photovoltaic grid-connected inverters (TLIs) can significantly reduce switching losses, as well as soften switching processes. Conventional dc–ac soft-switching configurations proposed by Dr. Deepakraj M. Divan are invalid in TLIs because of the leakage current problem. In order to develop soft-switching techniques in TLIs, this paper proposes a new soft-switching configuration and a procedure to guide the invention of soft-switching TLIs. First, this paper proposes two basic resonance tanks related to dc bus polarities, and then, uses these basic tanks to elevate four popular full-bridge-type TLIs according to the proposed guideline. As a result, four soft-switching TLIs are gained. Second, this paper picks obtained soft-switching highly efficient and reliable inverter concept (HERIC) as example to analyze its soft-switching operation principle and performance. As a consequence, all active switches of the gained soft-switching HERIC circuit are switched under both of zero-current turn-on and turn-off conditions; the reverse recovery problem of freewheeling diodes is alleviated owing to the zero-current turn-off of diodes; meanwhile, the common-mode voltage at the switching frequency scale is still constant. Finally, some experimental results from a 3-kW universal prototype at 50-kHz switching frequency are provided to verify the effectiveness of the main contributions of this paper. [ABSTRACT FROM AUTHOR]