Search

A mixed-signal adaptive ripple canceller for reducing switching noise and spurious emissions in switching regulators is presented. The proposed mixed-signal ripple suppression technique tracks and cancels the switching noise by utilizing two schemes: A primary mixed-signal adaptive ripple canceller that provides large signal ripple cancellation up to 20 dB, and an auxiliary linear amplifier-based ripple canceller that minimizes the residual ripple content, achieving a combined ripple rejection of 24 dB. Proposed approach operates without the need for external components, reducing overall printed circuit board area without loss of efficiency. The adaptive ripple canceller is designed and fabricated in a 250 nm CMOS process with four levels of metal. The ripple-canceller is integrated with an on-chip buck regulator to characterize its rejection effectiveness. The ripple canceller can also be utilized as a stand-alone ripple cleaner module with an external commercial-off-the-shelf (COTS) switching regulator. The proposed ripple canceller can track and cancel power supply ripple up to 1 MHz with 24 dB rejection and reduces ripple content up to fourth harmonic by at least 20 dB while supporting dc loads up to 1 A and ripple currents up to 350 mApk-pk. The proposed approach achieves 30% lower quiescent current than using a linear low-dropout regulator without the need for any external components. [ABSTRACT FROM AUTHOR]

High power supply rejection (PSR) with a wide rejection frequency band is becoming a critical requirement in linear low-dropout regulators (LDOs) used in complex systems-on-chip (SOCs). Typical LDOs achieve higher PSR within their loop-bandwidth; however, their supply rejection performance degrades with reduced loop-gain outside their loop-bandwidth. Typical LDOs with external filtering capacitors may also have spectral peaking in their PSR response, causing excess system-level supply noise. This work presents an LDO design approach, which achieves a PSR of higher than 68 dB up to 2 MHz frequency and over a wide range of loads up to 250 mA. The wide PSR bandwidth is achieved using a current-mode feedforward ripple canceller (CFFRC) amplifier which provides up to 25 dB of PSR improvement. The feedforward path gain is inherently matched to the forward gain of the LDO, not requiring calibration. The LDO has a fast load transient response with a recovery time of 6.1 $\mu \text {s}$ and has a quiescent current of 5.6 $\mu \text {A}$. For a full load transition, the LDO achieves settling with overshoot and undershoot voltages below 27.6 and 36.36 mV, respectively. The LDO is designed and fabricated in a 180 nm bipolar/CMOS/DMOS (BCD) technology. The CFFRC amplifier helps to achieve low quiescent power due to its inherent current mode nature, eliminating the need for supply ripple summing amplifiers and adaptive biasing. [ABSTRACT FROM AUTHOR]

Supply regulation using low quiescent current linear regulators helps in extending the battery life of power aware applications with very long standby time. A 1.24 $\mu \text{A}$ quiescent current NMOS low dropout (LDO) that uses a hybrid bias current generator (HBCG) which boosts the bias current dynamically and adaptively to improve the transient response is presented in this paper. A bias-current scalable error amplifier with an on-demand pull-up/pull-down buffer drives the NMOS pass device. The error amplifier is powered with an integrated dynamic frequency charge pump to ensure low dropout voltage. A low-power relaxation oscillator (LPRO) generates the charge pump clocks. A novel switched-capacitor pole tracking (SCPT) compensation scheme is proposed to ensure stability up to maximum load current of 150 mA with a low-ESR 1 $\mu \text{F}$ output capacitor. Designed in a 0.25 $\mu \text{m}$ CMOS process, the LDO has an output voltage range of 1–3 V, a dropout voltage of 240 mV, and a core area of 0.11 mm2. [ABSTRACT FROM AUTHOR]

A radiation-tolerant digital multiphase current-mode hysteretic point-of-load regulator fabricated on a commercial 180-nm CMOS process is presented. Experiments and simulations are used to demonstrate its single-event immunity and its total-dose tolerance over 100 krad(Si). Key electrical performance parameters are: 5-V input, 0.8–3.3 V output, 10-A load current, 93% peak efficiency, four-phase hysteretic quasi-current-mode buck converter with ±1.5% frequency synchronization, ±3.6% current sharing error, and 1% ripple. [ABSTRACT FROM AUTHOR]

Low-noise linear regulators are critical for power supply regulation of noise-sensitive circuits, such as ADCs, phase-locked loops, and other mixed-signal/RF system-on-a-chip designs. A low-noise low-dropout (LN-LDO) regulator using switched-RC bandgap reference and a multiloop, unconditionally stable error amplifier for output capacitorless operation is presented in this paper. A sample-and-hold switched-RC filter is developed to reduce the noise of the bandgap reference and drain-side modulated current-mode chopping technique is proposed to reduce the flicker (1/f) noise of the error amplifier. A switched capacitor notch filter is utilized to filter out the residual chopping ripple of the error amplifier. Thermal noise of the current reference circuit which is significant at such low noise levels is also reduced by using a low-area penalty passive RC filter. These techniques reduce the total integrated output noise of the LDO in the 10 Hz to 100 kHz band from $95.3\;\mu {{\rm{V}}_{{\rm{RMS}}}}$ down to $14.8\;\mu {{\rm{V}}_{{\rm{RMS}}}} . The LDO delivers a maximum load current of 100 mA with a dropout voltage of 230 mV and a quiescent current consumption of 40\;\mu \rmA . It achieves a power supply rejection of 50 dB at 10 kHz for a programmable output voltage range of 1–3.3 V. Fabricated in a 0.25\;\mu \rmm CMOS process, the LDO core occupies an area of 0.18 mm2. [ABSTRACT FROM AUTHOR]

Digital low-dropout (DLDO) regulators are gaining attention due to their design scalability for distributed multiple voltage domain applications required in state-of-the-art system-on-chips. Due to the discrete nature of the output current and the discrete-time control loop, the steady-state response of the DLDO has inherent output voltage ripple. A hybrid DLDO (HD-LDO) with fast response and stable operation across a wide load range while reducing the output voltage ripple is proposed. In the HD-LDO, a DLDO and a low current analog ripple cancellation amplifier (RCA) work in parallel. The output dc of the RCA is sensed by a 2-bit analog-to-digital converter, and the digitized linear stage current is fed into the DLDO as an error signal. During load transients, a gear-shift controller enables fast transient response using dynamic load estimation. The DLDO suppresses the output dc of the RCA within its current resolution. With this arrangement, a majority of the dc load current is provided by the DLDO and the RCA supplies ripple cancellation current. The HD-LDO is designed and fabricated in a 180-nm CMOS technology, and occupies 0.697 mm2 of the die area. The HD-LDO operates with an input voltage range of 1.43-2.0 V and an output voltage range of 1.0-1.57 V. At 100-mA load current, the HD-LDO achieves a current peak efficiency of 99.11% and a settling time of 15 clock periods with a 0.5-MHz clock for a current switching between 10 and 90 mA. The RCA suppresses fundamental, second, and third harmonics of the switching frequency by 13.7, 13.3, and 14.1 dB, respectively. [ABSTRACT FROM AUTHOR]

An all-digital sliding-mode (ADSM) controlled dc-dc converter, utilizing single-bit oversampled frequency domain digitizers in its feedback path is proposed. Sliding-mode control provides several benefits over the traditional PID control in terms of fast transient response, robustness to parameter and component variations, and low sensitivity to loop disturbances. However, analog implementations of sliding-mode control require several amplifiers in the controller and suffer from process, voltage, and temperature variations. In the proposed approach, the sliding-mode controller (SMC) is implemented digitally; utilizing a first order single-bit ΣΔ frequency to digital converter (ΣΔFDC)-based feedback and reference digitizing ADCs, running at 32-MHz sampling rate. The ADSM regulator achieves 1% settling time in less than 5 μs for a load variation of 600 mA. The SMC uses a high-bandwidth hysteretic differentiator and an integrator to perform the sliding control law in digital domain. The proposed approach overcomes the steady-state error (or dc offset), and band limits the switching frequency, which are the two common problems associated with SMCs. The IC is designed and fabricated on a 0.35-μm CMOS process occupying an active area of 2.72 mm2. [ABSTRACT FROM AUTHOR]

This paper presents a digitally controlled programmable point-of-load regulator for next-generation power systems. A novel digital control scheme was designed to minimize single-event effect (SEE)-induced transient effects. By effectively programming the loop transmission, the POL can trade off transient response time with SET robustness. The IC works with 1 to 5.5 V input voltage, 1–4.5V regulated output voltage, high efficiency (peak efficiency at 94%) and power of up to 5 W. The design was fabricated in the AMI i2t100 0.7 \mum complimentary, metal-oxide semiconductor (CMOS) process and characterized with the Jet Propulsion Laboratory (JPL) pulsed laser system. [ABSTRACT FROM PUBLISHER]