Search

As the size of micro light-emitting diodes (μLEDs) decreases, μLEDs encounter etching damage especially at the sidewalls that critically affects their properties. In this study, we investigated the influence of etching bias power (Pbias) on the performance of μLEDs and found that the current–voltage and light output–current characteristics of μLEDs were enhanced when Pbias was reduced. It was shown that at low Pbias, the chemical reaction between etching gas and gallium nitride, rather than ion sputtering, dominated the etching process, leading to low plasma damage and rough surface morphology. Additionally, to understand the etching-induced surface roughening behaviors, various substrates with different threading dislocation densities were treated at low Pbias. It was found that for the sample (with p-contact size of 10 × 10 μm2), the efficiency droop was approximately 20%, although the current reached 10 mA due most probably to the suppressed polarization effect in the quantum well. It was further observed that the external quantum efficiency (EQE) was dependent on Pbias, where the lowest Pbias yielded the highest maximum EQE, indicating that the plasma damage was mitigated by reducing Pbias. Optimization of dry etching and polarization-suppression conditions could pave the way for realizing high-performance and brightness μLEDs for next-generation displays. [ABSTRACT FROM AUTHOR]

The non-planar growth of UV-A laser diode heterostructures composed of AlGaN layers with high Al-mole-fractions and thicknesses exceeding the critical layer thickness was performed on patterned c-plane GaN (0001) substrates with stripe-shaped mesa structures. This approach suppressed the surface cracking at the top of the mesas via an anisotropic relaxation of the in-plane strain along the direction normal to the mesa stripes. Stimulated emission and laser operation at room temperature with emission in the UV-A range under pulsed current injection were demonstrated for laser diodes fabricated on the mesas. [ABSTRACT FROM AUTHOR]

Infrastructure facilities that were built approximately half a century ago have rapidly aged. Steel sheet piles, the inspection object in this study, are severely corroded, resulting in cave-in damages at wharfs. To solve such a problem, non-destructive inspection techniques are required. We previously demonstrated plate thickness measurement using extremely low-frequency eddy current testing. However, when the steel sheet piles are located in water, shellfish adhere to their surface, causing a lift-off of several tens of millimeters. Therefore, this large lift-off hinders the thickness measurement owing to fluctuations of magnetic signals. In this study, sensor probes with different coil diameters were prototyped and the optimum size for measuring steel sheet piles at high lift-off was investigated. Using the probes, the magnetic field was applied with a lift-off range from 0 to 80 mm, and the intensity and phase of the detected magnetic field were analyzed. Subsequently, by increasing the probe diameter, a good sensitivity was obtained for the thickness estimation with a lift-off of up to 60 mm. Moreover, these probes were used to measure the thickness of actual steel sheet piles, and measurements were successfully obtained at a high lift-off. [ABSTRACT FROM AUTHOR]

An AlGaN/GaN heterojunction bipolar transistor (HBT) with N-p-n configuration was fabricated by the “regrowth-free” method, resulting in a contamination-free emitter-base AlGaN/GaN heterojunction. The low-bias-power-based low-damage inductively coupled plasmaâ€"reactive ion etching was employed in this study for emitter mesa definition instead of the conventional selective-area-regrowth technique. The method successfully minimized the etching-induced damage in the p-GaN base layer and the contamination at the emitter-base AlGaN/GaN heterojunction. Consequently, the fabricated device exhibited a high current gain of 25, the highest current density of 15.0 kA cmâˆ'2, and the lowest on-state voltage offset of 0.75 V ever reported for AlGaN/GaN HBTs. [ABSTRACT FROM AUTHOR]

In this work, a deliberate etching-based top-down approach is proposed to fabricate the GaN nanorod (NR) Schottky barrier diode (SBD). As a key step during the fabrication, the impact of the wet-etching process on device performance is systematically studied. By virtue of the reduced surface states at the sidewall, the performance of NR SBD with the wet-etching process is substantially improved, delivering a forward turn-on voltage of 0.65 V, a current density of ∼10 kA/cm2 at 3 V, an ideality factor of 1.03, an ON/OFF current ratio of ∼1010, and no severe current collapse, along with a reverse breakdown voltage of 772 V. [ABSTRACT FROM AUTHOR]

We demonstrated the formation of excellent Ohmic contact to ${p}$ -type GaN (including the plasma etching-damaged ${p}$ -type GaN which otherwise exhibited undetectable current within ±5 V) by the post-growth diffusion of magnesium. The specific contact resistivity on the order of $10^{-{4}}\,\,\Omega $.cm2 (extracted at V = 0 V) was achieved on the plasma-damaged ${p}$ -GaN with linear current-voltage characteristics by the transfer length method (TLM) measurement. The improvement in current by a factor of over 109 was also obtained on the plasma-damaged p-n junction diode after the same Mg-treatment. These experimental results indicate a great potential of post-growth diffusion of Mg to overcome the bottleneck of forming a good Ohmic contact to ${p}$ -GaN. [ABSTRACT FROM AUTHOR]

We have demonstrated a fabrication process for the Ohmic contact on low-doping-density p-type GaN with nitrogen-annealed Mg. An Ohmic contact with a contact resistance of 0.158 Ω cm2 is realized on p−-GaN ([Mg] = 1.3 × 1017 cm−3). The contact resistance of p-type GaN with higher Mg concentration ([Mg]=1.0 × 1019 cm−3) can also be reduced to 2.8 × 10−5 Ω cm2. A localized contact layer is realized without any etching or regrowth damage. The mechanism underlying this reduced contact resistance is studied by scanning transmission electron microscopy with energy dispersive x-ray spectroscopy and secondary ion mass spectrometry, representing a mutual diffusion of Ga and Mg atoms on the interface. Reductions in the barrier height and surface depletion width with the nitrogen-annealed Mg layer are confirmed by XPS and Hall effect measurements qualitatively. [ABSTRACT FROM AUTHOR]

The interface properties of GaN metal–insulator–semiconductor (MIS) structures with a gate electrode metal deposited by electron beam (EB) or resistive heating evaporation were investigated. Also, the impact of the interface properties on the channel mobility in GaN MIS field-effect transistors was investigated. It was confirmed that interface charges including both interface states and positive fixed charges were introduced to an Al2O3/GaN interface by the formation of a gate electrode by EB evaporation. Consequently, the introduced interface charges degraded the electron mobility in the MIS channel. [ABSTRACT FROM AUTHOR]

An optimized top-down approach was utilized to fabricate vertical GaN-on-GaN nanowire Schottky barrier diodes (NWSBDs) in this letter. The suppressed reverse leakage current and enhanced breakdown voltage (BV) of the vertical GaN NWSBDs are attributed to the reduced electric field at the interface of the Schottky junction achieved through the dielectric reduced surface field technique. As-fabricated NWSBD delivers a low turn-on voltage of 0.80 V, a near-unity ideality factor of 1.04, along with a soft BV of 480 V. The measured soft BV is comparable with the avalanche BV of the p–n diode with a similar net doping concentration in the drift region. [ABSTRACT FROM AUTHOR]

Inductively coupled plasma–reactive ion etching (ICP–RIE)-induced damage in heavily Mg-doped p-type GaN ([Mg] = 2 × 1019 cm−3) was investigated by low-temperature photoluminescence (PL) and depth-resolved cathodoluminescence (CL) spectroscopy. From PL measurements, we found broad yellow luminescence (YL) with a maximum at around 2.2–2.3 eV, whose origin was considered to be isolated nitrogen vacancies (VN), only in etched samples. The depth-resolved CL spectroscopy revealed that the etching-induced YL was distributed up to the electron-beam penetration depth of around 200 nm at a high ICP–RIE bias power (Pbias). Low-bias-power (low-Pbias) ICP–RIE suppressed the YL and its depth distribution to levels similar to those of an unetched sample, and a current–voltage characteristic comparable to that of an unetched sample was obtained for a sample etched with Pbias of 2.5 W. [ABSTRACT FROM AUTHOR]

We report the first experimental demonstration of microwave oscillation in GaN impact ionization avalanche time transit (IMPATT) diodes at the X-band. The device used in this study is a single drift diode with a p+–n simple abrupt junction and vertical mesa termination. The reverse I–V characteristic of the diode shows low leakage current, clear avalanche breakdown, and high avalanche capability, as required for IMPATT operation. Microwave testing is performed in an X-band waveguide circuit with a reduced-height waveguide resonant cavity. Oscillations are observed at 9.52 GHz at a power of ∼56 mW. [ABSTRACT FROM AUTHOR]

Photo-electrochemical (PEC) etching is a promising technique for fabricating GaN microelectromechanical systems devices. In this study, we demonstrate the fabrication of GaN cantilevers by the bandgap-selective PEC etching of an InGaN superlattice sacrificial layer. By using an InGaN superlattice as a sacrifice layer, we found the PEC etching rate became higher than using a normal InGaN layer. As a result, the InGaN superlattice was completely etched and we fabricated GaN-based cantilevers whose resonance characteristics were measured. The Young's modulus of GaN was determined from the resonance characteristics of GaN cantilevers to be the same as the highest value reported previously. [ABSTRACT FROM AUTHOR]

GaN metal-insulator-semiconductor field-effect transistors (MISFETs) with Ni/Al2O3/GaN gate stack structures formed on a vicinal Ga-polar (c-plane) or nonpolar (m-plane) surface were fabricated. Current–voltage characteristics and carrier transport properties of the channels in the MISFETs with and without post-metallization annealing (PMA) were systematically investigated. GaN layers grown on freestanding substrates with vicinal surfaces led to good transistor behaviors for the m-plane as well as the c-plane. It was found that PMA improves the electron mobility in the MIS channel (μEFF) for both the c- and m-planes, and that μEFF for the m-plane is slightly higher than that for the c-plane both with and without PMA. Temperature dependences of μEFF clarified that μEFF for the m-plane is dominantly limited by phonon scattering, while both Coulomb and phonon scatterings are dominant for the c-plane. Consequently, we achieved high performance for the GaN MISFETs fabricated on the m-plane because of the reduced numbers of Coulomb scattering centers at the Al2O3/GaN interface. [ABSTRACT FROM AUTHOR]

Herein, gallium nitride (GaN) samples implanted with magnesium (Mg) and fluorine (F) ions are investigated by photoluminescence (PL) measurements. In low‐temperature PL measurements, the characteristic green luminescence (GL) band attributable to nitrogen vacancies (VN) is observed in Mg‐ion‐implanted GaN. As VN are likely to act as donors, suppressing their formation is essential to realizing p‐type conductivity. The energy required for a F impurity to replace VN in GaN and eventually form F on a N site decreases when the Fermi level approaches the valence band maximum, and therefore F is employed as a subsequent implantation element to compensate for VN. The GL band peak disappears upon implanting Mg and F ions at a high temperature and adjusting the F concentration to an appropriate value. This result suggests that VN generated by Mg ion implantation can be suppressed using an element with a lower formation energy than that of VN. [ABSTRACT FROM AUTHOR]

Phase-shifting electron holography (PS-EH) using a transmission electron microscope (TEM) was applied to visualize layers with different concentrations of carriers activated by Si (at dopant levels of 1019, 1018, 1017 and 1016 atoms cm−3) in n -type GaN semiconductors. To precisely measure the reconstructed phase profiles in the GaN sample, three electron biprisms were used to obtain a series of high-contrast holograms without Fresnel fringes generated by a biprism filament, and a cryo-focused-ion-beam (cryo-FIB) was used to prepare a uniform TEM sample with less distortion in the wide field of view. All layers in a 350-nm-thick TEM sample were distinguished with 1.8-nm spatial resolution and 0.02-rad phase-resolution, and variations of step width in the phase profile (corresponding to depletion width) at the interfaces between the layers were also measured. Thicknesses of the active and inactive layers at each dopant level were estimated from the observed phase profile and the simulation of theoretical band structure. Ratio of active-layer thickness to total thickness of the TEM sample significantly decreased as dopant concentration decreased; thus, a thicker TEM sample is necessary to visualize lower carrier concentrations; for example, to distinguish layers with dopant concentrations of 1016 and 1015 atoms cm−3. It was estimated that sample thickness must be more than 700 nm to make it be possible to detect sub-layers by the combination of PS-EH and cryo-FIB. [ABSTRACT FROM AUTHOR]

In this study, GaN m‐plane Schottky barrier diodes are fabricated by metalorganic vapor‐phase epitaxy (MOVPE) on several off‐angle gallium nitride (GaN) substrates, and the off‐cut angle dependence of impurity incorporation is investigated. We show that the MOVPE layer on the substrate inclined 5° toward the [000–1] direction has extremely low impurity incorporation. These results provide important suggestions for the fabrication of m‐plane power devices. [ABSTRACT FROM AUTHOR]

Dislocations that cause a reverse leakage current in vertical p-n diodes on a GaN free-standing substrate were investigated. Under a high reverse bias, dot-like leakage spots were observed using an emission microscope. Subsequent cathodoluminescence (CL) observations revealed that the leakage spots coincided with part of the CL dark spots, indicating that some types of dislocation cause reverse leakage. When etch pits were formed on the dislocations by KOH etching, three sizes of etch pits were obtained (large, medium, and small). Among these etch pits, only the medium pits coincided with leakage spots. Additionally, transmission electron microscopy observations revealed that pure screw dislocations are present under the leakage spots. The results revealed that 1c pure screw dislocations are related to the reverse leakage in vertical p-n diodes. [ABSTRACT FROM AUTHOR]

In this study, GaN m-plane Schottky barrier diodes fabricated with a metalorganic vapor-phase epitaxy on a GaN substrate were investigated using emission microscope, photoluminescence, and cathodoluminescence. In addition, facet dependence of leakage current under reverse-biased condition was observed. We showed that the leakage-current distribution was caused by the facet dependence of the carrier concentration and oxygen concentration. These results can provide important suggestions for the fabrication of m-plane devices. (a) four-faceted hillocks on m-plane GaN MOVPE sample, facet dependence of (b) leakage current and (c) PL peak intensity of the m-plane GaN Schottky barrier diode. [ABSTRACT FROM AUTHOR]

A normally-off GaN double-implanted vertical MOSFET (DMOSFET) with an atomic layer deposition (ALD)-Al2O3 gate dielectric film on a free-standing GaN substrate fabricated by triple ion implantation is presented. The DMOSFET was formed with Si ion implanted source regions in a Mg ion implanted p-type base with N ion implanted termination regions. A maximum drain current of 115 mA/mm, maximum transconductance of 19 mS/mm at a drain voltage of 15 V, and a threshold voltage of 3.6 V were obtained for the fabricated DMOSFET with a gate length of 0.4 μm with an estimated p-type base Mg surface concentration of 5 × 1018 cm−3. The difference between calculated and measured Vths could be due to the activation ratio of ion-implanted Mg as well as Fermi level pinning and the interface state density. On-resistance of 9.3 mΩ·cm2 estimated from the linear region was also attained. Blocking voltage at off-state was 213 V. The fully ion implanted GaN DMOSFET is a promising candidate for future high-voltage and high-power applications. [ABSTRACT FROM AUTHOR]

Infrastructure facilities that were built approximately half a century ago have rapidly aged. Steel sheet piles, the inspection object in this study, are severely corroded, resulting in cave-in damages at wharfs. To solve such a problem, non-destructive inspection techniques are required. We previously demonstrated plate thickness measurement using extremely low-frequency eddy current testing. However, when the steel sheet piles are located in water, shellfish adhere to their surface, causing a lift-off of several tens of millimeters. Therefore, this large lift-off hinders the thickness measurement owing to fluctuations of magnetic signals. In this study, sensor probes with different coil diameters were prototyped and the optimum size for measuring steel sheet piles at high lift-off was investigated. Using the probes, the magnetic field was applied with a lift-off range from 0 to 80 mm, and the intensity and phase of the detected magnetic field were analyzed. Subsequently, by increasing the probe diameter, a good sensitivity was obtained for the thickness estimation with a lift-off of up to 60 mm. Moreover, these probes were used to measure the thickness of actual steel sheet piles, and measurements were successfully obtained at a high lift-off.