Search

An extended-duty-ratio (EDR) boost converter is studied extensively in this paper for high voltage gain applications with a wide input (and/or output) voltage range. The EDR is a unique combination of an interleaved, multiphase boost converter and switched capacitor configuration that achieves high voltage gain with significantly lower switch voltage stress and switching losses compared to conventional high-gain solutions. Most of the switches in the multiphase EDR experience only a fixed fraction of the output voltage ($1/M, 2/M$ , etc., where $M$ is the number of phases). Through extensive analysis over a wide operating range, it is shown here that the EDR boost converter has inherent current sharing among the phases only in a limited range of duty ratio— $(M-1)/M \leq D \leq 1$. As the duty ratio reduces beyond this range as required in wide input voltage applications, inherent current sharing property is lost. In this paper, techniques to ensure current sharing under all operating zones without requiring current sensors are presented. Instead of having equal duty ratio for each phase, it is adjusted for each phase according to the operating region of the converter. Extensive analysis is presented to derive the required duty ratio changes for the different phases. The proposed concept is validated with experimental results from a 250 W, 3-phase EDR boost, and GaN-based hardware prototype. [ABSTRACT FROM AUTHOR]

This paper proposes a wide-range zero-voltage-switching (ZVS) active-clamped current-fed push–pull converter for fuel cell application. The presented converter achieves ZVS for all of the primary switches and ZCS for secondary diodes from rated load to 10% full load over the wide input voltage variation, improving the overall efficiency. The ZVS of switches is realized by the energy stored in the transformer leakage inductance aided by the secondary parallel inductor. An additional active clamping circuit suppresses the voltage spike as well as assists in realizing ZVS of switches. Low-voltage-rated switches with low on-state resistance can be used. Moreover, the voltage-doubler rectifier is adopted to release the reverse-recovery problem of rectifier diodes and reduce turns ratio of the high-frequency transformer. Detailed steady-state operation, analysis, design, control, comparative study, and experimental results are discussed in depth in this paper. Finally, a 200-W prototype has been built in the laboratory to verify the effectiveness of the proposed converter. [ABSTRACT FROM PUBLISHER]

In this paper, two topologies are presented for the enhanced-boost quasi-Z-source inverters (qZSI), namely continuous input current configuration and discontinuous input current configuration of enhanced-boost qZSI with two-switched impedance networks. Similar to enhanced-boost impedance-source inverters (ZSIs), these proposed inverter topologies possess very high boost voltage inversion at low shoot-through duty ratio and high modulation index to provide an improved quality output voltage. Compared to enhanced-boost ZSIs with two-switched Z-source impedance networks, these proposed inverter topologies share common ground with source and bridge inverter, overcome the starting inrush problem, and draw continuous input current and the lower voltage across the capacitors. Moreover, the input ripple current is negligible. This paper presents the operating principles and analysis of continuous input current configuration enhanced-boost qZSI with two-switched impedance networks and compares with ZSI, switched inductor ZSI, DA/CA-qZSI, and enhanced-boost ZSIs. The theoretical analysis is done and is validated through simulation and experimental results. [ABSTRACT FROM PUBLISHER]

This paper proposes a family of soft-switching bidirectional converters. In many applications, the bidirectional converters operate over a wide range of duty cycle and load variations. In the proposed converters, in order to extend the zero-voltage switching operation range, two supplemental voltage sources utilizing passive components are implemented in the auxiliary circuit. By using this method, the soft-switching features are ensured for an extensive range of the converter duty cycles. This is achieved independent of the output power value or the converter operation mode, and so, soft switching is ensured within the entire converter operating region. In these converters, all semiconductors components are soft switched, and the auxiliary circuit does not contribute to the complexity of the control circuit. Also, no extra voltage stress exists on the main switches and the voltage stress on the auxiliary switches is lower than the main switches voltage stress. In this paper, the proposed bidirectional buck/boost converter is analyzed and to confirm the feasibility of the proposed method, experimental results of a 150-W prototype converter are presented. [ABSTRACT FROM PUBLISHER]

Conventional single-phase power-factor-correction (PFC) rectifiers with active power decoupling capability typically require more than three active switches in their circuits. By exploring the concept of power-buffer cell, a new single-stage PFC rectifier with two active switches, one inductor and one small power-buffering capacitor is reported in this paper. The proposed converter can achieve high-power factor, wide output voltage range, and power decoupling function without using electrolytic capacitor. Additionally, an automatic power decoupling control scheme that is simple and easy to implement is proposed in this paper. The operating principle, control method, and design considerations of the proposed rectifier are also provided. A 100-W prototype with ac input voltage of 110 Vrms and a regulated dc output voltage ranging from 30 to 100 V has been successfully designed and practically tested. The experimental results show that with only a 15 μF power-buffering film capacitor, the proposed converter can achieve an input power factor of over 0.98, peak efficiency of 93.9%, and output voltage ripple of less than 3%, at 100-W output power. [ABSTRACT FROM PUBLISHER]

A new static synchronous compensator (STATCOM) based on the diode-clamped modular multilevel converter (DCM2 C) is proposed in this paper. In this converter topology, the capacitor voltage is clamped by using a low power rating diode in each submodule. The quantity of voltage sensors is significantly reduced and is free from the number of voltage levels. Furthermore, the voltage balancing control method becomes very simple and the capacitor voltage balance speed is fast. Based on the structure of modular multilevel converter, the DCM2C-STATCOM has the capability of Var compensation and negative-sequence current compensation. The topology characteristics and compensation control method of DCM2C-STATCOM are investigated in this paper. Experimental results obtained from a laboratory prototype validate that the capacitor voltage of the proposed DCM2C-STATCOM can be well balanced and the Var and negative-sequence current compensations are effective. [ABSTRACT FROM AUTHOR]

The essential features of a DC–DC converter for fuel cell vehicle are to ensure the higher voltage gain to meet out the higher DC link voltage demand, continuous input current to improve the life span of the fuel cell, presence of common grounding to avoid electromagnetic interference issue and lower voltage stress with reduced components. This paper presents a high voltage gain DC–DC converter by combining the switched capacitor and quasi switched boost network modules. The proposed high voltage gain converter provides the continuous input current, lower voltage stress, utilizes a fewer number of elements and common grounding feature. The operating characteristics, steady-state analysis both in continuous current mode (CCM) and discontinuous current mode (DCM), comparative analysis with contemporary converters are discussed. The theoretical claimed analysis is validated by the simulation and experimental study. The proposed converter is operated for 200 W output power rating and tested for providing the voltage gain in the range of 5–8 times the input voltage gain by varying the input voltage from 25 V–40 V. The efficiency of the proposed converter is also reported for different output power rating which is in the range 91.3%–93.7%. [ABSTRACT FROM AUTHOR]

In this paper, an electric vehicle (EV) battery charger with interleaved Landsman converter (ILC) followed by a flyback converter, is designed and evaluated for improved power quality (PQ) charging of battery. A built-in wave-shaping is obtained at the charger front-end due to improved PQ characteristics of ILC. This PFC converter consists of two Landsman converter cells, which are designed in discontinuous conduction mode (DCM) to share the input and output currents. The current sharing at input results into lower input current ripple as well as peak current stress through the switch, is reduced. This, further improves the input current harmonics profile. Moreover, the reduced output voltage ripple gives reduced rms current in the output capacitor. A phase shift PWM scheme (PSPWM) is used for ILC and the duty cycle for the switches is selected below 50%. This allows the ripple cancellation at line and load sides. The interleaving at PFC stage as well as DCM based design ensures a low cost charging solution as compared to the conventional Landsman converter (CLC) based chargers in this power range. However, the flyback converter provides the current control during the charging of the battery in constant current (CC) and constant voltage (CV) regions. The harmonics spectrum of mains current follows the recommended PQ regulations over a range of varying line voltages and loadings. [ABSTRACT FROM AUTHOR]

This paper introduces the bridgeless triple-mode resonant ac–dc converter and presents its dynamic model and control technique. The proposed converter operates in triple mode: discontinuous-conduction mode (DCM), continuous-conduction mode (CCM), and missing resonance mode (MRM). It has the advantages of small number of required components, medium power capacity, and high efficiency, but it is difficult to control because DCM, CCM, and MRM have their own dynamic characteristics. To solve this control problem, the mode boundaries are first identified and, corresponding to each mode, the dynamic model is developed to design the controller. In each mode, we propose to add a repetitive controller (RC) with a phase-lead compensator to the conventional duty ratio plus feedback controller. The RC is used to suppress the deterministic periodic disturbances and the phase-lead compensator is used to compensate for the incurred phase lag. A 1-kW digitally controlled converter prototype is built and used to demonstrate the validity of the proposed modeling and control approach. [ABSTRACT FROM AUTHOR]

A soft-switched nonisolated high step-up dc–dc converter based on the quasi-impedance-source structure is presented in this paper. In the proposed converter, a technique similar to the synchronous rectifier is applied such that the diode of the impedance network is replaced with an active switch. In this way, not only is conduction loss associated with the diode reduced but also zero-voltage-switching characteristics for power switches are provided. Also, output diodes of the proposed converter are switched under zero-voltage-zero-current-switching condition which extremely reduces their switching and reverse-recovery losses. It is shown that by correct design of the components, soft-switching performance is retained for all the semiconductor devices over the entire range of output load. All these factors together with simplicity of the proposed structure result in high efficiency over a wide range of output power. Moreover, the proposed converter benefits from continuous input current and a shared ground between input and output. Operating principles of the proposed converter along with its steady-state analysis are presented. Also, experimental results obtained from a laboratory prototype for 48 to 350 V voltage conversion and 100 W nominal power are provided to validate the feasibility of the proposed converter. [ABSTRACT FROM AUTHOR]

This paper introduces a novel single-phase buck–boost noninverting variable-frequency ac–ac converter that offers higher efficiency compared to the competitors. This converter utilizes a lower number of semiconductors. A simple and flexible switching strategy is also proposed, which generates the desired output waveform avoiding unnecessary high-frequency switching operation of semiconductor devices. A high reliable operation due to the elimination of the input source shoot-through risk, an inherent commutation capability that mitigates the voltage spikes across the semiconductors, a lower semiconductors rating requirement, an improved input current waveform quality, and a smaller required input filter inductor are the main advantages of the proposed converter. Thus, the proposed converter can be successfully applied to many industrial applications such as medium-frequency transformer isolation for traction and wind turbine converters, ac–dc high-voltage conversion based on Cockcroft–Walton circuit and induction heating systems. The theoretical achievements and claims are all confirmed through extensive experimental tests on a 200-W laboratory setup. [ABSTRACT FROM AUTHOR]

In this paper, eight ultrahigh-voltage gain dc–dc converters are proposed. These sets of converters are derived by the association of boost cells, coupled inductor, voltage multiplier, switched capacitors, and LC filter cells. The nonpulsating input and output converters are evaluated in terms of: principle of operation, voltage gain, voltage and current stress, estimated power losses, and efficiency. Following full analysis prototypes built in the laboratory show experimental results verifying the theoretical analysis. [ABSTRACT FROM AUTHOR]

In this paper, closed-loop control and boundary condition for continuous conduction mode and discontinuous conduction mode of nonisolated inverting N× multilevel boost converter (MBC) are articulated. Inverting N× MBC combines the features of classical boost converter and voltage multiplier to attain inverting N times higher voltage. Consequently, the inverting N× MBC provides a viable solution for high-voltage step-up photovoltaic applications with low voltage rating reactive components and semiconductor devices. The control strategy with saturation limiter is employed to achieve highly stable voltage. The modes of operation, benefits of inverting N× MBC, and key factors for the selection of semiconductor devices and sizing of the reactive components are discussed. Additionally, the effects of reactive components and semiconductor devices on the output voltage are examined. Experimental results of the developed circuit are presented to validate the design of converter, and effectiveness and robustness of the implemented control algorithm for different input and output side perturbations. [ABSTRACT FROM AUTHOR]

In this paper, a voltage sensorless controller is developed for a two-switch single-phase rectifier that involves power factor correction and active pulsating power buffering without electrolytic capacitors. While a two-switch rectifier normally requires four sensed signals for control, only one current sensor is required in this proposal, thereby offering advantages such as low cost, high compactness, isolation between control and power circuits, and improved reliability. While the basic operating principle follows that of a conventional voltage sensorless controller for single-switch converters, several critical design considerations are the key to the success of the implementation which is explained in detail. The feasibilities of the controller are experimentally testified with a 100-W rectifier prototype regarding both steady state and dynamic performance. [ABSTRACT FROM AUTHOR]

In this paper, a new transformerless buck–boost converter based on a ZETA converter is introduced. The proposed converter has the ZETA converter advantages, such as buck–boost capability, input-to-output dc insulation, and continuous output current. The suggested converter voltage gain is higher than the classic ZETA converter. In the presented converter, only one main switch is utilized. The proposed converter offers low voltage stress of the switch; therefore, the low on-state resistance of the main switch can be selected to decrease the losses of the switch. The presented converter topology is simple; hence, the control of the converter is simple. The converter has the continuous output current. The mathematical analyses of the presented converter are given. The experimental results confirm the correctness of the analysis. [ABSTRACT FROM AUTHOR]

Renewable energy generations have been attracting sustained attentions in academic and industry. Current-fed-isolated-bidirectional dc/dc converters (CF-IBDCs) are widely adopted in low-voltage high-current applications such as solar photovoltaic fuel cell with energy storage. This paper gives an overview and a comprehensive comparative evaluation of CF-IBDCs. The active clamped, dual half-bridge, L-L type dual active bridge, resonant-type, naturally clamped, and other type topologies of CF-IBDCs are investigated, analyzed, and compared regarding their circuit topological structures, operation characteristics, modulation methods, and soft-switching technologies. In addition, component cost models and loss models of converters are deduced and presented. On this basis, quantitative and comprehensive performance comparison of seven typical CF-IBDC topologies selected from each type is conducted in terms of costs, losses, weight, volume, and power density for the given system specifications and design constraints. Finally, the application range of different CF-IBDCs and future trend are presented to encourage further development. [ABSTRACT FROM AUTHOR]

In this paper, a novel topology combining reconfigurability and hybridization is presented. Reconfigurability allows the proposed converter to operate in three different operating modes, yielding a wide range of step-up conversion ratios. The combination of two charge-pump cells and an inductor allows to reduce the average inductor current if compared to a standard equivalent boost converter. A prototype with integrated MOS, drivers, and logic but external passives was built. Experimental results show that with $\mathbf {f_{s} }=\text{300}\,$ kHz, $\mathbf {V_{in} = \text{6}}\,$ V, and $\mathbf {I_o = \text{70}}\,$ mA, the converter can cover conversion ratios in the range from $\text {2.5}$ to $\text {10}$ , with a maximum output voltage equal to $\text {60}\,$ V. Peak efficiency is $\text {91}$ %. When the output current is increased to $\text {100}\,$ mA peak efficiency is $\text {92.8}$ %. [ABSTRACT FROM AUTHOR]

In this paper, a family of new step-up series–parallel dual resonant switched-capacitor converters (SP-DRSCs) is proposed to extend the conversion ratio for high step-up applications. The converters feature a wide gain range, continuously adjustable, and enhanced light-load voltage regulation. All flying capacitors operate in resonance, eliminating high transient current spikes and charge sharing losses. Thus, zero-current-switching (ZCS) turn-on for all transistors and ZCS turn-off for all diodes are achieved. A comprehensive analysis of the operation principle, voltage-gain curves, stable regulation range, and voltage and current stress is given. An analytical method to quantify the passive component volume for the group of step-up dual resonance switched-capacitor converters is presented. Further design considerations to optimize the passive component volume of the proposed SP-DRSC and the effect of bulky bypass capacitors on the volume are discussed. [ABSTRACT FROM AUTHOR]

This paper presents a new single-phase ac–dc–ac three-level three-leg converter composed of three coupled-inductors and six active switches. The system model, operation principles, and a control strategy are presented and discussed. Additionally, a space-vector pulsewidth modulation technique is developed to double the effective frequency of the grid and load voltages and to reduce the switching losses. The proposed converter is compared to other similar converters in terms of switch count, harmonic distortion, and power losses. The results show that the proposed topology has improved power quality and uses fewer switches and gate drive circuits. These characteristics can potentially reduce the costs and the complexity of the system. In addition, the proposed converter eliminates the requirement for dead time to prevent short circuit of the dc-link. In order to validate the theoretical analysis, simulated and experimental results are presented and discussed. [ABSTRACT FROM AUTHOR]

This paper presents a pulsed power modulator with a new structure that utilizes the reverse recovery characteristics of diodes to achieve an effective pull-down circuit configuration. The proposed configuration for active pull-down applicable to negative pulsed power applications with a high-voltage direct switching method is implemented by adding a diode to the pulse discharging path of the modulator, instead of using a pull-down resistor. The diode is forward-biased while an output pulse voltage is applied to the load. When the pulse voltage applied to the load is removed, the residual energy in the load is quickly discharged through the reverse recovery path of the diode so that the pull-down function of the pulsed power supply system is efficiently performed. The operating principle of the proposed system is described, and each operating mode is analyzed in detail. In addition, the feasibility of the proposed system configuration is examined through various simulation results. Finally, it is proven that the proposed system can be used effectively in pulsed power application fields through a practical experiment in plasma source ion implantation applications. [ABSTRACT FROM AUTHOR]

Circuit analysis and design criteria of a two-phase bidirectional converter with high voltage gain are presented in this paper. The operating principle of the forward or reverse mode is similar to that of the conventional buck or boost converter. Compared with the conventional converter, the switch stresses can be reduced significantly depending on the operating region of the voltage ratio in the two-phase converter. The power losses can also be reduced due to the use of low-voltage rating switches. The derivate converters are discussed to demonstrate the advantages of the proposed topology. A 200 W/1 MHz two-phase prototype converter with gallium nitride (GaN) devices is built and tested to verify the feasibility. [ABSTRACT FROM AUTHOR]

In this paper, the design methodology of switched-tank converter (STC) is presented. The power loss breakdown analysis is conducted to point out the directions and paths for components optimization. It is revealed that the switching device conduction loss, printed circuit board (PCB) loss, and inductor loss become significant when output power is >150 W. Power loss of four switches is calculated and compared for switching device selection. The resonant capacitor is carefully designed to meet both current stress and ripple requirements. On the other hand, optimal design of the resonant inductors and PCB layout are fully investigated. The core loss model is provided, and different core materials are compared to minimize the core loss. Besides, a fine-tuned inductor winding structure is designed to achieve the lowest winding loss. Furthermore, PCB layout is optimized to get short loop length for each operation state. In addition to the hardware level optimization, an improved control method is proposed, in which the conduction time of switching devices is tuned to mitigate the circulating power. To verify the optimization work, a prototype of STC is built and tested. The experimental results indicate that a state-of-the-art performance of 98.71% efficiency and a 1000 W/in3 high power density is achieved. [ABSTRACT FROM AUTHOR]

The Cuk dual resonance core (DRC) realizes overlapped dual resonance to regulate its output voltage. However, the DRC configuration was only applied to the Fibonacci switched-capacitor converter (SCC), series–parallel SCC, and voltage doubler. In this paper, the Cuk DRC is modified and then is extended to the Dickson SCC to form a multi-resonance-core-based (MRC) Dickson resonant switched-capacitor converter. All charging and discharging loops achieve soft charging, and so the inherent capacitor charge sharing loss and the high current transient spikes are eliminated. The modular configuration makes the MRC Dickson easy to be extended to a higher voltage level. The on-time fixed frequency modulation is adopted, all transistors being turned on with zero-current-switching (ZCS) operation and all diodes being turned off with ZCS operation. Most importantly, the conversion ratio of the MRC Dickson can be regulated continuously, widely, and efficiently even at light load condition, which is a huge advantage over the traditional Dickson SCC with limited control headroom. A comprehensive analysis of the operation principle, voltage-gain curve, component stress analysis, and output characteristic is provided. The converter operation principle and regulation capability were verified by both simulation and experiment. [ABSTRACT FROM AUTHOR]

Load-independent output characteristics of inductive power transfer (IPT) systems are increasingly popular in battery charging. This paper proposes a novel variable-parameter T-circuit (VT) for an IPT system charging a battery with constant current (CC) or constant voltage (CV) output. The VT can transfer a CC/CV input to a CC or CV output by using an ac switch and a passive component (inductor or capacitor). An IPT system with a VT for CC–CV charging can reduce the number of passive components and ac switches. Besides, the proposed VT merits more design freedom of charge current/voltage with the constraints imposed by the loosely coupled transformer parameters compared to that of the traditional one. In addition, there are three kinds of VTs for various IPT charging systems with different requirements. A 400 W laboratory-scale prototype with a 150 mm air gap was built to verify the theoretical analyses. Both electronic load and lead-acid battery are utilized to verify the charging profile of the proposed method. The experimental results of the IPT system indicate that the fluctuation of the charging current in CC mode is less than 2%, and the change rate of charging voltage in CV mode is within 2.9%. The maximum overall efficiency 93.93% of the charging system is achieved from a dc 110 V input to a dc 100 V output. [ABSTRACT FROM AUTHOR]

This paper proposes the design of gray wolf optimizer (GWO) algorithm-based fractional order proportional integral (FOPI) controller for power factor correction (PFC) using interleaved dc–dc single ended primary inductance converter converter with improved performance characteristics such as speed, accuracy, and stability. The detailed analysis and modeling of the proposed converter are presented. The optimal parameters of FOPI controller are obtained using GWO algorithm to improve the speed of response of the system. FOPI controller provides better performance in terms of robustness and stability since it has one more adjustable parameter than the conventional proportional integral (PI) controller. The cascade control strategy is implemented for the proposed converter with GWO-based FOPI controller as inner current and outer voltage controllers for PFC and load voltage regulation. The performance characteristics of the proposed system are analyzed and compared with conventional and other optimization techniques using MATLAB/Simulink software. A prototype of the proposed converter controlled by TMS320C2000 microcontroller for an output power of 200 W is tested and validated with the simulation results. The proposed system is used for powering devices like robots in critical applications such as military, space craft, etc., where stability, speed, and accuracy are major concerns. [ABSTRACT FROM AUTHOR]

For photovoltaic applications, the flyback microinverter with pseudo-dc-link is popular as a simple topology but brings large transformer turns ratio and thus large leakage inductance, which would deteriorate the converter efficiency. To solve this issue, based on the nonisolated pseudo-dc-link structure, this paper proposed a hybrid boost–flyback/flyback (BF/F) microinverter. This new topology is operated at the BF mode for the most segment of a half grid cycle and the F mode for the rest. During the BF mode, high voltage gain with low voltage stress is easily available in minimized transformer turns ratio. Besides, the leakage energy is recycled and the turn-off voltage spike of the main switch is clamped, as a result of a passive snubber inherently contained in this mode. Given that the BF mode is lack of step-down function, the F mode is developed to regulate the output voltage even for values lower than the input voltage. The operation and characteristic of the hybrid BF/F microinverter in boundary conduction mode are analyzed in detail, and the mathematical expression of reference current is derived theoretically to guarantee high power quality. Finally, a 240 W prototype was implemented to validate the theoretical analysis and the benefits of the proposed topology. [ABSTRACT FROM AUTHOR]

This paper presents a new highly integrable hybrid step-down converter that merges switched-inductor and switched-capacitor operations and significantly reduces onboard loss by using the input cable's parasitic inductance as its main inductor. This converter has the inductor placed at the input with a smaller voltage swing, leading to possible use of a smaller inductor and low-voltage rating switches that generally translate to reduced conduction losses. Analyses of converter operation and losses to reveal its original characteristics and design guidelines are presented to facilitate the components optimization. The converter architecture is verified by a proof-of-concept 15-W inductor-less lithium-ion battery charger prototype that uses a 1-m USB 3.0 cable as inductor. The converter, switched at 2 MHz from a 5-V input, experimentally achieves 89.7% peak efficiency and 6% higher efficiency at full load than a Buck converter counterpart. This high efficiency and zero onboard inductor yield a relative 45.7% onboard loss reduction at full load, promising excellent integration feasibility and superior system thermal management. [ABSTRACT FROM AUTHOR]

This paper proposes a novel isolated high step-down conversion circuit, called an integrated buck and modified push−pull (IBMPP) converter, which is able to lower the voltage level on the primary side of the ideal transformer, resulting in a lower turns-ratio and decreased leakage inductance. The IBMPP converter is able to prevent the duty cycle from operating in extremely low conditions. Furthermore, the proposed converter adopts active-clamp techniques to recycle leakage energy and to suppress voltage spikes, so that the conversion efficiency can be effectively improved. The advantages of the IBMPP converter are its simple topology, easy control mechanism (which requires only two signals with a 180-degree phase shift), high conversion ratio, low component counts for power switches, and less voltage stress on some of the switches on the high-voltage side. The operation principle, steady-state analysis, design considerations, and experimental results of the proposed IBMPP converter are presented in detail. The feasibility of the IBMPP is verified by hardware implementation. The full-load efficiency at 250 W is 81.44%, and the input and output voltages are 380 and 5 V, respectively. [ABSTRACT FROM AUTHOR]

Analysis and design of a single-switch high step-up coupled-inductor boost converter are presented in this paper. With the aid of the coupled inductor, the proposed converter can achieve high-voltage gain without extreme duty cycle. Also, low switch voltage stress can be achieved, thus low-voltage-rating mosfet is allowed to lower the conduction loss. Moreover, the proposed converter features continuous input current, which is desirable and friendly to the battery, fuel cell, and photovoltaic applications. In addition, the reverse recovery problem of the diodes can be alleviated and leakage energy can be recycled. The operation principles and characteristics of the proposed converter are discussed. Experimental results are provided to verify the theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper presents a self-adapting synchronized-switch harvesting (SA-SSH) interface circuit to extract energy from vibration-based piezoelectric energy harvesters (PEHs). The implemented circuit utilizes a novel switching technique to recycle optimum amount of harvested charge on piezoelectric capacitance to strengthen the damping force, and simultaneously achieve load-independent energy extraction with a single inductor. Charge recycling is realized by adjusting extraction time, and optimized through a maximum power point tracker based on charge-flipping dissipation. The circuit has been implemented using 180 nm HV CMOS technology with 0.9 × 0.6 mm2 active area. Self-adapting SSH circuit has been validated with both macro-scaled and MEMS PEHs with different inductor values. The interface circuit provides maximum energy extraction for the full storage voltage range of 1.8–3.7 V. The implementation harnesses have 500% more power compared to an ideal full-bridge rectifier, and output 3.4 μW for 2.24 V peak-to-peak open-circuit piezoelectric voltage from MEMS PEH excited at its resonant frequency. [ABSTRACT FROM AUTHOR]

Photovoltaic (PV) systems having rechargeable batteries are prone to be complex and costly because multiple converters are necessary to individually regulate a load, PV panel, and battery. This paper proposes novel nonisolated multiport converters (MPCs) integrating a bidirectional pulsewidth modulation (PWM) converter and phase-shift-switched capacitor converter (PS-SCC) for standalone PV systems. A PWM converter and PS-SCC are integrated by reducing the total switch count, realizing the simplified system and circuit. In the proposed MPCs, two control freedoms of duty cycle and phase shift angle are manipulated to individually regulate the load, PV panel, and/or battery. The detailed operation analysis was performed to mathematically derive gain characteristics and zero voltage switching operation boundaries. For the battery discharging mode, in which the PV panel is not available and the MPC behaves as a single-input–single-output converter with two control freedoms available, the optimized control scheme achieving the lowest rms current is also proposed to maximize power conversion efficiencies. Various kinds of experimental verification tests using a 200-W prototype were performed to verify the theoretical analysis and to demonstrate the performance of the proposed MPC. [ABSTRACT FROM AUTHOR]

Boost-based converters are used in a variety of non-isolated step-up applications, such as power factor correctors, because of their simplicity. The power density of these converters can be increased in higher switching frequencies, which reduces the size of the magnetic elements. This increases the switching losses, but that can be solved by soft-switching techniques. This paper proposes a resonant bridgeless power factor correction converter that provides soft switching for all of the semiconductors. The proposed structure can provide zero voltage switching for the switches and zero current switching for the diodes. In the proposed structure, the input current is inherently sinusoidal with low total harmonic distortion, even with small inductances. Therefore, a high input power factor is achieved without requiring a current control loop in the circuit. This reduces the complexity of the control circuit. An experimental prototype has been constructed to investigate the validity of the claims. Experimental results show near-unity power factor, as well as $\text{2}\%$ efficiency improvement at full load when compared to a conventional interleaved boost converter with the same components. [ABSTRACT FROM AUTHOR]

In this paper, a new low-voltage ringing zero voltage transition (ZVT) cell is proposed for a family of non-isolated dc–dc converters. In the proposed converter, all semiconductor devices operate under soft-switching condition at both turning on and off. The proposed ZVT cell resolves the issues appeared in the previous works: no online calculation required to achieve ZVS turn-on of the main switch; no extra voltage stress imposed on the main or snubber components; no floating gate driver required for the main and snubber switches; low component count of the ZVT cell; operation principles and design guideline of the boost converter with the proposed ZVT cell are presented. Also, three different positions of a snubber diode considering its junction capacitor are analyzed to clarify the advantage of the proposed ZVT cell. A 2-kW laboratory prototype of the boost converter with the proposed ZVT cell operating at 100 kHz is built and tested to verify the theoretical analysis. Finally, a comparative analysis is given to demonstrate the superiority of the proposed converter. [ABSTRACT FROM AUTHOR]

This paper presents a new bridgeless buck–boost power factor corrector with the use of the active virtual ground technique, which is named as the Manitoba Rectifier. The proposed topology can convert the grid ac voltage into a wide range of voltage outputs within a single-stage circuit. It is in a bridgeless structure and simple in design. During the operation, an LC filter is generated at the system input, where continuous grid current is guaranteed in a buck–boost characteristic topology. In addition, the filter capacitor helps to clamp the voltage ripple between the grid and the output bus terminal. Both leakage current and common mode noise are kept in a relatively small value. Thus, a single-stage and low common-mode buck–boost converter system is built. The proposed topology is successfully implemented on an 800 W prototype, and the performance is experimentally verified, which shows good agreement with the theoretical findings. [ABSTRACT FROM AUTHOR]

In this paper, a new high voltage gain step-up dc–dc converter is proposed for interfacing renewable power generation. The configuration optimally integrates both the coupled-inductor and switched-capacitor techniques to achieve an ultra-high step-up gain of voltage conversion with low voltage stress and high efficiency. It consists of a voltage boost unit, a passive clamp circuit, and a symmetrical voltage multiplier network. The structure becomes modular and extendable without adding any extra winding for ultra-high step-up voltage gain. The proposed topology not only reduces the voltage stress on the main switch but also maintains it steady for the entire duty cycle range. Furthermore, the reverse recovery issue of the diodes is alleviated through the leakage inductance of the coupled inductor. The operation principle and steady-state analysis are presented in detail. Experimental evaluation validates the claimed advantages and demonstrates a well-distributed efficiency curve and the peak of 96.70%. [ABSTRACT FROM AUTHOR]

The three-level full-bridge (TLFB) dc−dc converter has been widely used in high-voltage, high-power applications. In the experimental test, the neutral-point voltage deviation appears; moreover, it has also been found out that if the flying capacitors are introduced, the input capacitor voltages could realize self-balance even if no active balancing solutions are adopted. In the previous publications, the role of flying capacitors is generally considered to extend the range of soft switching; however, the self-balance ability has not been mentioned or investigated in any publications thus far. In order to fill this gap, this paper provides the detailed mode operation analysis of the TLFB converter and reveals the cause of the imbalance. In addition, the mechanism of the self-balance ability provided by the flying capacitors is explained in detail, which gives a deep insight into the converter. At last, the influence factor of the voltage error in steady state has been analyzed, and the specific expression of the voltage error is also derived. The feasibility of the theoretical analysis is verified by the simulation and experimental results. [ABSTRACT FROM AUTHOR]

A novel PWM full bridge (FB) dc–dc converter for large power industrial applications is proposed in this paper. The soft switching mode of the primary switches can be varied under different input and output conditions to achieve optimum system efficiency. In the zero-voltage and zero-current switching (ZVZCS) mode, the turn-on and turn-off switching loss can be optimized because the soft switching conditions of the turn-on and turn-off instants are well decoupled. In the zero-voltage switching (ZVS) mode, the turn-off switching loss can also be optimized because there is no requirement for light load operation in this mode. Four mosfets with ultra-low on-state resistance are used, thus, the added conduction loss is small. The auxiliary mosfets with high switching frequency are turned on with zero-current and off with zero-voltage, hence, the added switching loss can also be neglected. Furthermore, some drawbacks of the conventional ZVS and ZVZCS converters, e.g., narrow ZVS load range, high primary circulating current, incomplete reset of the primary current, and unreasonable VA rating of the added components, have been well solved. The operation principles and soft switching characteristics are discussed. Experimental results from an 18-kW prototype are provided to verify the proposed converter. [ABSTRACT FROM AUTHOR]

This paper presents a new configuration of high gain (HG) single ended primary inductor converter (SEPIC) with a ripple-free input current to maximize the efficiency of the PV panel for standalone water pumping system (WPS). The ripple eliminating circuit combined with the HG SEPIC converter to achieve reduced ripples in photovoltaic (PV) current is independent to the duty cycle control and hence, it can be easily integrated to the main power circuit of configuration. This circuit does not need any active switches, control, or drive circuit for its execution. The ripple eliminating circuit yields a complete removal of the electrolytic capacitor connected across the PV array and significantly reduces the inductance of the HG SEPIC converter. It also improves the response and power density of the dc–dc converter. The large gain of dc–dc converter enables the use of low-voltage PV panel and minimizes the partial shading and parasitic capacitance effects on PV array source. Due to the substantial compatibility between natural characteristics of switched reluctance motor (SRM) drive and WPS, a four-phase SRM drive is utilized in the proposed scheme. In addition, a single current sensor based maximum power point tracking technique is utilized in the proposed system, which helps to reduce the cost and improve the accuracy of the overall system. Analytical, simulated, and experimental results of the developed system are presented to demonstrate the performance of the system. [ABSTRACT FROM AUTHOR]

A modular quasi-resonant bidirectional dc–dc converter composed of half-bridge gallium nitride modules (HBGM) with reduced switch voltage stress is proposed in this paper. By using an auxiliary capacitor, a resonant circuit is formed to shape the current and voltage so that zero-voltage switching at turn-on instant is achieved. Since the switching loss dominates the power losses in a high-frequency dc–dc converter, the soft-switching performance leads to a noticeable reduction in the total loss; so, the operating temperature will decrease, and consequently, size of the heatsink will be reduced. The proposed circuit takes advantage of enhancement-mode gallium nitride (eGaN) switches regarding their small on-resistance RDS(on), low gate charge, and fast switching speed to improve both efficiency and power density. The main performance issue of adopting GaN switches in a bidirectional dc–dc converter is the high voltage stress of GaN devices, which is handled by connecting the HBGM in the active-clamped stacked configuration, as well as optimizing printed circuit board layout design. Finally, a 1 kW, 600 V laboratory prototype operating at 100 kHz is implemented to validate the proposed concept. [ABSTRACT FROM AUTHOR]

DC microgrid is gaining attraction and a recent trend in distribution power generation system due to penetration of renewables (especially photovoltaic or fuel cell). In this paper, a new triple-switch-triple-mode high step-up converter (TSTM-HS converter) is presented for dc microgrid applications. In the proposed converter, voltage lift technique is employed and range of duty cycle is extended by incorporating an additional switch in converter circuitry. By doing this, high voltage conversion ratio is achieved without using a transformer, coupled inductor, and multiple stages of switched capacitors. Moreover, the TSTM-HS converter operated in three modes with two types of the duty cycles to achieve low to high voltage conversion without using high duty cycle for each switch. The effects of difference in the inductance values on the regulation and operating behavior of the TSTM-HS converter are discussed. The continuous conduction mode and discontinuous conduction mode characteristics of the TSTM-HS converter are discussed in detail with steady-state analysis and boundary condition. The comparison is provided to highlight the benefits of the TSTM-HS converter. The selection of semiconductor devices and the design of reactive components are discussed for the TSTM-HS converter. The experimental results of the proposed converter are provided which validate the theoretical approach, performance, and feasibility of converter. [ABSTRACT FROM AUTHOR]

This paper proposes a high-step-down dc–dc converter with continuous output current which utilizes coupled-inductors. Another main feature of this converter is applying the same number of switches as the synchronous buck converter. The introduced converter is suitable for non-isolated low-voltage high-current applications, especially voltage regulator modules (VRMs) with 12-V-input. Owing to extension of the duty cycle, the main mosfet current stress and the synchronous rectifier switch voltage stress are significantly reduced. However, the discharge of the leakage inductance energy increases the main mosfet voltage stress. By employing a simple lossless clamp/snubber circuit the leakage inductance energy is recovered, the voltage spike across the main mosfet is clamped, and the turn-off switching losses are reduced. There is at least one inductor in all current paths which creates an intrinsic protection against current shoot-through and provides zero-current-switching (ZCS) turn-on for the main mosfet. High efficiency is attained by the proposed converter due to extended duty cycle, low number of switches, and soft switching operation while the converter driver is just like the conventional buck converter. Due to the single-phase structure of the proposed converter, this converter is a viable alternative to the buck VRM. Similar to the other converters using coupled-inductors, the complexity of coupled-inductors design and the space occupied by coupled-inductors can be considered as drawbacks. A prototype of the proposed converter is implemented to verify the converter operation and the theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper describes a theory to synthesize nonisolated dc–dc converters. It uses the fundamental flux balance equation across the inductors of a converter as a starting point in this synthesis process. The flux balance equations are the linear equations of the input voltage, capacitor voltages, and duty cycle (D). The coefficients of these linear equations can be selected from a finite set of choices. These choices define the converter topologies that are subsequently used to synthesize a converter. The synthesis procedure applies to a converter of multiple order. All the possible converters are identified for a first-order topology. In the case of second-order converters, all the choices of the flux balance equation are defined. Based on these choices, three new quadratic topologies are derived and verified to demonstrate the effectiveness of the theory. The procedure to synthesize a converter from a given voltage conversion ratio is also outlined. [ABSTRACT FROM AUTHOR]

High step-up boost converters with coupled inductor have attracted much attention in the fuel cell or photovoltaic grid-connected generation system, however, there are few literatures elaborated on the construction ideas and derivation methods of them. Accordingly, in order to obtain a clear roadmap on the derivation and inner connection of these converters, a comprehensive review and analysis are presented in this paper. First, the basic boost converter with coupled inductor is regarded as the basic topology, and its merits and demerits are analyzed in detail. Then, in order to address these demerits, various step-up techniques are introduced, such as the rectifier circuit, the active-clamped circuit, the multi-winding coupled inductor, and the voltage doubler rectifier; and numerous new topologies are continuously proposed by combinations and equivalent simplifications. In addition to a detailed synthesis of each topology, a comparative and quantitative analysis among some important converters is presented, and the optimal one is chosen to build a 250 W prototype. Finally, based on comparisons and analysis, the main characteristics and inner connections of these high step-up boost converters with coupled inductor are identified and clarified. [ABSTRACT FROM AUTHOR]

In this paper, an integrated step-up inverter without transformer is investigated for photovoltaic (PV) power generation. The proposed topology can be derived by combining a traditional boost converter with a single-phase full bridge dc–ac converter. The main features of the integrated inverter are: First, the leakage current caused by the solar cell array-to-ground parasitic capacitance can be theoretically reduced to zero due to the characteristics of the converter configuration, which can improve the efficiency and the reliability of the PV generation system; second, the output ac voltage of the proposed inverter can be higher than the input dc voltage, which is capable of connecting low voltage PV panels to the grid; third, only five active switches are used in the presented inverter, and those switching devices can be synchronously driven by various sinusoidal pulsewidth modulation methods based on the carrier; therefore, the proposed inverter is compact and with curtailed cost. The working principle and analysis of the proposed integrated inverter are elaborated. Finally, simulation and experimental results are obtained in a lab prototype, which agree well with the theoretical analysis. [ABSTRACT FROM AUTHOR]

A novel high step-down dc–dc converter with voltage demultiplier cell is proposed in this paper, which is widely used in the high step-down applications such as electric vehicle and digital circuits. The combination of switched-capacitor and coupled-inductor is employed to build extended voltage demultiplier in the proposed converter, which makes a quite higher voltage conversion ratio than that of the existing counterparts. Thus, the proposed converter can achieve extremely low output voltage with an appropriate duty ratio, and the extreme duty cycle is avoided. Accordingly, voltage stress on power switches is greatly reduced. Then, mosfets with low conduction resistance could be utilized to reduce conduction loss. Importantly, zero-voltage switching could be achieved for the main switch, which promotes the conversion efficiency further. In addition, the coupled inductor operates not only as a filter inductor, but also as a transformer when the main switch is in the off state, which reduces the volume of the magnetic core and improves the power density of the converter. The operation principle, performance analysis, design considerations of the proposed converter and performance comparison with recent counterparts are discussed in detail, and finally, an experimental prototype is built to verify the theoretical analysis and performance of the proposed converter. [ABSTRACT FROM AUTHOR]

This paper presents a single-stage single-switch soft-switching (S6) power factor correction (PFC) converter to enhance the current shaping performance and reduce the total harmonic distortion. This improvement is achieved by the aid of an auxiliary winding which is used to lower the input current harmonics and also achieve soft-switching condition. As a result, the switching losses are reduced and harmonic content of the input current is improved noticeably in comparison to the conventional S6 PFC converter. Also, the total number of semiconductor elements is reduced in the proposed topology which results in lower cost and higher efficiency. The operating modes of the proposed converter are discussed in detail and the design procedure is presented. A 200-kHz prototype of the proposed converter is implemented and the obtained results are provided to verify the converter theoretical analysis and operation. [ABSTRACT FROM AUTHOR]

This paper proposes a voltage-source parallel resonant Class E inverter. The proposed circuit has a shunt capacitor including parasitic capacitance of a switching device and achieves zero-voltage switching and zero-voltage derivative switching at turning-on like a classical Class E inverter. Therefore, high power conversion efficiency is achieved under high operating frequency. Unlike the other Class E inverters, the proposed circuit has no choke inductor or dc blocking capacitor. Moreover, it has a parallel resonant tank unlike the classical Class E inverter. Thus, a circuit protection is not required in a wireless power transfer system. Circuit analysis, circuit simulations, and circuit experiments were carried out. The experimental circuit performed the desired operation and the power conversion efficiency was 93.2% with the output power 4.76 W at the operating frequency 1 MHz. [ABSTRACT FROM AUTHOR]

An improved bridgeless (BL) Cuk converter-based electric vehicle (EV) battery charger with high power factor and increased efficiency is designed and developed in this paper. It provides low cost and high-power-density-based charging solution for the EV. This charger incorporates less number of devices operating over one switching cycle, which reduces the additional conduction loss incurred by a diode bridge rectifier of the conventional charger. Hence, it improves the charger's efficiency. The added advantage of the proposed topology is that the unwanted capacitive coupling loop is removed, as well as the unwanted conduction through the body diode of the inactive switch in the previously developed BL Cuk converter is avoided. This significantly improves the charger's efficiency. For the constant current and constant voltage charging, the commands are synchronized by a flyback converter. The proposed charger draws a sinusoidal current from ac mains and the total harmonic distortion in the supply current is reduced to the limits specified by the IEC 61000-3-2 guidelines. The improved efficiency and power quality indices of the proposed charger are investigated to demonstrate its satisfactory charging operation at all operating conditions. [ABSTRACT FROM AUTHOR]

This paper presents a novel switch current stress reduction technique for a single switch boost-flyback high step up dc–dc converter. Coupled inductor-based converters do not have a sufficiently higher inductance value of their windings. This creates current surge during transient and steady state, which in turn increases current stress at main switch. To compensate this difficulty in coupled inductor-based boost flyback converter, an inductor–diode parallel combination has been connected in series with the switch. This technique increases the effective inductance of the coupled inductor primary winding during switch turn-on operation and helps to reduce current stress. Steady-state operating principle with the proposed technique is analyzed in continuous conduction mode. The current reduction technique is discussed with a proper mathematical derivation. To verify theoretical findings, simulation study is carried out in MATLAB/Simulink R2014b. Finally, a laboratory-based 40-W prototype converter is designed to show the effectiveness of the proposed switch current reduction technique. [ABSTRACT FROM AUTHOR]

A new transformerless bidirectional buck-boost converter is proposed in this paper. The proposed converter has a simple circuit structure, low component count, low voltage stress on the power transistors, and a wide voltage gain range. This makes it applicable in the energy storage charge/discharge systems, such as electric vehicles (EV), microgrids and nanogrids with energy storage units, and uninterruptible power supplies. In addition, synchronous rectification between the complementary transistors is employed to improve the converter efficiency. A comprehensive analysis of the steady-state operation, small-signal model, component parameters design, and efficiency analysis of the proposed converter operating in a continuous conduction mode is given. Finally, a 1.6-kW scaled-down prototype was built using Silicon Carbide MOSFETS to validate the effectiveness and feasibility of the proposed converter. [ABSTRACT FROM AUTHOR]