Search

DC microgrid is gaining attraction and a recent trend in distribution power generation system due to penetration of renewables (especially photovoltaic or fuel cell). In this paper, a new triple-switch-triple-mode high step-up converter (TSTM-HS converter) is presented for dc microgrid applications. In the proposed converter, voltage lift technique is employed and range of duty cycle is extended by incorporating an additional switch in converter circuitry. By doing this, high voltage conversion ratio is achieved without using a transformer, coupled inductor, and multiple stages of switched capacitors. Moreover, the TSTM-HS converter operated in three modes with two types of the duty cycles to achieve low to high voltage conversion without using high duty cycle for each switch. The effects of difference in the inductance values on the regulation and operating behavior of the TSTM-HS converter are discussed. The continuous conduction mode and discontinuous conduction mode characteristics of the TSTM-HS converter are discussed in detail with steady-state analysis and boundary condition. The comparison is provided to highlight the benefits of the TSTM-HS converter. The selection of semiconductor devices and the design of reactive components are discussed for the TSTM-HS converter. The experimental results of the proposed converter are provided which validate the theoretical approach, performance, and feasibility of converter. [ABSTRACT FROM AUTHOR]

Parallel interleaved two-level (2L) three-phase voltage source inverters (VSIs) are widely used due to their distinct advantages of high power delivery, modularity, low current rating devices, etc. Along with these advantages, the parallel interleaved 2L VSIs could also be analyzed as a single three-level (3L) VSI. Conventionally parallel interleaved 2L VSIs are modulated using the 2L pulsewidth modulation (PWM) techniques. However, implementation of parallel interleaved 2L VSIs using the 2L PWM techniques may generate a higher ac side current ripple as compared to implementing the parallel interleaved 2L VSIs using 3L PWM techniques. This paper proposes a carrier-based method for implementing different 3L discontinuous PWM (DPWM) techniques for parallel interleaved 2L three-phase VSIs. Comparison of different 2L switching sequences for implementing a 3L DPWM switching sequence based on circulating current, line current ripple, and switching loss is also carried out. Simulation and experimental results are also displayed to validate the proposal. [ABSTRACT FROM AUTHOR]

Control-to-output transfer function of the classical boost converter in continuous conduction mode contains a right-half-plane (RHP) zero that limits its frequency response. In this paper, to eliminate this zero and enhance the dynamic performance, a forward path for energy transfer to output within the on interval of the power switch is provided using the magnetic coupling. This approach simply eliminates the RHP zero by introducing an inductor coupled to the boost inductor, a diode, and a capacitor into the classical boost topology. In addition, the provided forward path enhances the voltage gain, which makes it possible to achieve a smaller operating duty cycle and reduced voltage stress for the power switch in applications with large voltage conversion ratios. Using this approach does not complicate the control structure, and a traditional single-loop voltage control scheme can be used to regulate the output voltage. The proposed approach is analytically examined by obtaining the averaged state-space model of the resulting converter, and a criterion to eliminate the RHP zero is presented. Experimental results from an implemented laboratory prototype for 48- to 200-V voltage conversion and 100-W nominal power are provided. [ABSTRACT FROM AUTHOR]

Droop control is broadly used in dc power distribution systems, e.g., dc microgrids. Implementing droop control for switch mode power supplies requires the measurement of average current. Synchronous sampling is used in digital control systems to obtain the average of a triangular inductor waveform. However, the dead time, semiconductor turn-on and turn-off delays, and signal conditioning delays shift the sensed waveform and change the effective duty cycle, resulting in a misalignment and measurement error from the average value. This paper proposes a duty cycle weighted averaging method based on double sampling. By sampling twice per switching period and averaging the results using duty cycle as the weighting factor, the error due to waveform misalignment is theoretically eliminated. The result always equals the average value of the triangle. This method does not rely on the knowledge of circuit delays, making it easy to implement and robust to parameter variations. Simulations and experimental measurements validate the superior performance compared with conventional single and double sampling methods. The experiment on a droop-controlled dc–dc converter demonstrates a more accurate droop characteristic. [ABSTRACT FROM AUTHOR]

This paper proposes an interleaved totem-pole bridgeless boost power factor correction (PFC) converter with soft-switching capability. In the proposed converter, an inductor is added compared with the conventional interleaved totem-pole bridgeless boost PFC converter. The added inductor is located between two PFC converter units, and by utilizing the energy of the added inductor, all switches can achieve the zero voltage switching (ZVS). In addition, by applying the phase-shifting control between two PFC converter units, the proposed converter can control the magnitude of the current flowing on the added inductor as an optimal value. Therefore, the proposed converter can achieve the ZVS operation, while minimizing the additional conduction loss and core loss of the added inductor. As a result, the proposed converter can achieve the high efficiency. The feasibility of the proposed converter is confirmed with 180–264 Vrms input and 1.6 kW (400 V/4 A) output prototype. [ABSTRACT FROM AUTHOR]

The pulse-width modulated (PWM) switching rectification that can achieve a high power factor (PF) for increasing the energy transfer efficiency between an LC resonator and a rectifier and voltage step-up and -down conversion is proposed for a wireless power transfer (WPT) receiver. The proposed method can emulate the switching rectifier as a resistive load by using an inductor and integrated phase synchronizers. Additionally, similar to a switched-inductor converter that controls the duty cycle ratio (D), the proposed PWM rectifier can control the output voltage VOUT when the input is a rectified, wirelessly coupled voltage instead of a constant voltage. Thus, unlike a conventional PWM switching rectifier for ac mains, an additional voltage conditioning circuit would not be needed after the proposed rectifier for WPT. The proposed PWM switching rectification is implemented in the AMS 0.18 μm 1.8 V/5 V CMOS process. PF = 1 is measured, indicating the most efficient energy transfer, compared to only 0.55–0.65 in a peak detection rectifier. Additionally, 88.2% of peak power conversion efficiency of the switching rectifier is achieved, and the maximum output power is 80.3 mW at 500 kHz of the WPT frequency. Moreover, the measured voltage conversion ratios ranging between 0.73× and 2× are demonstrated in this paper. [ABSTRACT FROM AUTHOR]

This paper proposes a high-step-down dc–dc converter with continuous output current which utilizes coupled-inductors. Another main feature of this converter is applying the same number of switches as the synchronous buck converter. The introduced converter is suitable for non-isolated low-voltage high-current applications, especially voltage regulator modules (VRMs) with 12-V-input. Owing to extension of the duty cycle, the main mosfet current stress and the synchronous rectifier switch voltage stress are significantly reduced. However, the discharge of the leakage inductance energy increases the main mosfet voltage stress. By employing a simple lossless clamp/snubber circuit the leakage inductance energy is recovered, the voltage spike across the main mosfet is clamped, and the turn-off switching losses are reduced. There is at least one inductor in all current paths which creates an intrinsic protection against current shoot-through and provides zero-current-switching (ZCS) turn-on for the main mosfet. High efficiency is attained by the proposed converter due to extended duty cycle, low number of switches, and soft switching operation while the converter driver is just like the conventional buck converter. Due to the single-phase structure of the proposed converter, this converter is a viable alternative to the buck VRM. Similar to the other converters using coupled-inductors, the complexity of coupled-inductors design and the space occupied by coupled-inductors can be considered as drawbacks. A prototype of the proposed converter is implemented to verify the converter operation and the theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper describes a theory to synthesize nonisolated dc–dc converters. It uses the fundamental flux balance equation across the inductors of a converter as a starting point in this synthesis process. The flux balance equations are the linear equations of the input voltage, capacitor voltages, and duty cycle (D). The coefficients of these linear equations can be selected from a finite set of choices. These choices define the converter topologies that are subsequently used to synthesize a converter. The synthesis procedure applies to a converter of multiple order. All the possible converters are identified for a first-order topology. In the case of second-order converters, all the choices of the flux balance equation are defined. Based on these choices, three new quadratic topologies are derived and verified to demonstrate the effectiveness of the theory. The procedure to synthesize a converter from a given voltage conversion ratio is also outlined. [ABSTRACT FROM AUTHOR]

High step-up boost converters with coupled inductor have attracted much attention in the fuel cell or photovoltaic grid-connected generation system, however, there are few literatures elaborated on the construction ideas and derivation methods of them. Accordingly, in order to obtain a clear roadmap on the derivation and inner connection of these converters, a comprehensive review and analysis are presented in this paper. First, the basic boost converter with coupled inductor is regarded as the basic topology, and its merits and demerits are analyzed in detail. Then, in order to address these demerits, various step-up techniques are introduced, such as the rectifier circuit, the active-clamped circuit, the multi-winding coupled inductor, and the voltage doubler rectifier; and numerous new topologies are continuously proposed by combinations and equivalent simplifications. In addition to a detailed synthesis of each topology, a comparative and quantitative analysis among some important converters is presented, and the optimal one is chosen to build a 250 W prototype. Finally, based on comparisons and analysis, the main characteristics and inner connections of these high step-up boost converters with coupled inductor are identified and clarified. [ABSTRACT FROM AUTHOR]

High power pseudospark switches (PSSs) can control pulsed high voltage, high peak current discharges. In this paper, a PSS in series with a saturable inductor at the anode is investigated. The commutation process is analyzed with a time-resolved method. And the effects of the number of magnetic cores and anode voltages on discharge characteristics are studied experimentally. At the beginning of commutation process, when the anode voltage is 10.4 kV with four magnetic cores, the inductor is unsaturated, and there is a flat plateau of the forward voltage drop after the anode voltage drops rapidly to about 200 V, at the same time the current rise rate is 2.8 kA/ $\mu \text{s}$. When the inductor is saturated, there is a voltage spike that occurs at the end of the flat plateau, and the current simultaneously rises rapidly at the rate of 6.4 kA/ $\mu \text{s}$. The current sharp rise lags behind the voltage drop of the pseudospark gap, and the electrode erosion and energy dissipation reduce significantly. When the anode voltage is 15.6 kV, the commutation losses reduce by about 30% with seven cores in series at the anode. As a result, it is evident that the discharge process will speed up if the anode voltage is higher. And the trigger delay decreases by up to 8% when the anode voltage varies from 5.2 to 15.6 kV. Finally, in order to obtain a reproducible pseudospark discharge by the use of a saturable inductor, the number of magnetic cores has to be optimized for different anode voltages. [ABSTRACT FROM AUTHOR]

This paper describes a study on the high-voltage compact solid-state pulsed-power modulator for parallel reactor operation. The current capacity of the pulsed modulator has been improved to drive multiple reactors in parallel. The pulse discharge switch uses the IXYK120N120C3 (1200 V/120 A) insulated-gate bipolar transistor for a high current output. The gate driver has been improved according to the characteristics of the replaced switch. The output specifications of the modified pulsed-power modulator are a maximum output voltage of 40 kV, a maximum output current of 300 A, a pulsewidth ranging from 1.5 to $5~\mu \text{s}$ , a maximum repetition rate of 3 kHz, and an average power of 13 kW. The modulator has the dimensions of $450 \times 475 \times 600$ mm3, a maximum peak power of 12 MW, and a maximum power density of 93 kW/L. A resistive load experiment and a plasma reactor parallel drive test were performed. Four parallel reactors were driven using one modulator. In addition, a 50% reduction in the concentration of toluene was obtained through the experiment of the toluene gas treatment using only parallel plasma reactors. [ABSTRACT FROM AUTHOR]

In this paper, an integrated step-up inverter without transformer is investigated for photovoltaic (PV) power generation. The proposed topology can be derived by combining a traditional boost converter with a single-phase full bridge dc–ac converter. The main features of the integrated inverter are: First, the leakage current caused by the solar cell array-to-ground parasitic capacitance can be theoretically reduced to zero due to the characteristics of the converter configuration, which can improve the efficiency and the reliability of the PV generation system; second, the output ac voltage of the proposed inverter can be higher than the input dc voltage, which is capable of connecting low voltage PV panels to the grid; third, only five active switches are used in the presented inverter, and those switching devices can be synchronously driven by various sinusoidal pulsewidth modulation methods based on the carrier; therefore, the proposed inverter is compact and with curtailed cost. The working principle and analysis of the proposed integrated inverter are elaborated. Finally, simulation and experimental results are obtained in a lab prototype, which agree well with the theoretical analysis. [ABSTRACT FROM AUTHOR]

A novel high step-down dc–dc converter with voltage demultiplier cell is proposed in this paper, which is widely used in the high step-down applications such as electric vehicle and digital circuits. The combination of switched-capacitor and coupled-inductor is employed to build extended voltage demultiplier in the proposed converter, which makes a quite higher voltage conversion ratio than that of the existing counterparts. Thus, the proposed converter can achieve extremely low output voltage with an appropriate duty ratio, and the extreme duty cycle is avoided. Accordingly, voltage stress on power switches is greatly reduced. Then, mosfets with low conduction resistance could be utilized to reduce conduction loss. Importantly, zero-voltage switching could be achieved for the main switch, which promotes the conversion efficiency further. In addition, the coupled inductor operates not only as a filter inductor, but also as a transformer when the main switch is in the off state, which reduces the volume of the magnetic core and improves the power density of the converter. The operation principle, performance analysis, design considerations of the proposed converter and performance comparison with recent counterparts are discussed in detail, and finally, an experimental prototype is built to verify the theoretical analysis and performance of the proposed converter. [ABSTRACT FROM AUTHOR]

This paper presents a single-stage single-switch soft-switching (S6) power factor correction (PFC) converter to enhance the current shaping performance and reduce the total harmonic distortion. This improvement is achieved by the aid of an auxiliary winding which is used to lower the input current harmonics and also achieve soft-switching condition. As a result, the switching losses are reduced and harmonic content of the input current is improved noticeably in comparison to the conventional S6 PFC converter. Also, the total number of semiconductor elements is reduced in the proposed topology which results in lower cost and higher efficiency. The operating modes of the proposed converter are discussed in detail and the design procedure is presented. A 200-kHz prototype of the proposed converter is implemented and the obtained results are provided to verify the converter theoretical analysis and operation. [ABSTRACT FROM AUTHOR]

This paper investigates an approach for achieving zero-voltage switching of an interleaved bi-directional buck–boost converter over a wide input–output voltage operating range by utilizing a coupled inductor with a variable coupling coefficient. The approach is based on regulating the value of the coupling coefficient by means of a direct current depending on the converter conversion ratio, thereby controlling the amplitude and duration of the resonant voltage transition. The impact of the controllable value of the coupling coefficient on the equivalent inductance, the zero-voltage transition period, and the resonant amplitude is analyzed in detail by applying analytical modeling. In comparison to the converter with a fixed coupled inductor operating over a wide input–output voltage span, the variable coupled inductor significantly improves the soft-switching range and reduces the circulating energy. Outside of the controllable resonant amplitude region, the converter with a variable coupled inductor still achieves reduction in the duration of the resonant transition period. To validate theoretical analysis, experimental results are recorded on the gallium nitride interleaved bi-directional buck–boost converter prototype. Improvements in efficiency at both full and half loads in comparison to the prototype with a fixed coupled inductor are achieved. [ABSTRACT FROM AUTHOR]

For high-voltage and high-power bidirectional dc–dc converters, soft switching of all active power devices is mandatory to ensure the high efficiency and reliability. This paper describes a control technique for wide-range zero-voltage switching (ZVS) implementation of dual-bridge series-resonant dc–dc converters. The proposed control technique integrates variable-frequency modulation (VFM) and phase-shift modulation (PSM), in which the former effectively achieves the ZVS for both step-down and step-up operation, while the latter is employed to further extend the power transmission capability. The proposed technique is built on the time-domain analysis of the ZVS condition. A closed-form solution is formulated that guarantees the sufficient ZVS commutation current at switching instants, accounting for the presence of switches parasitic and/or snubber capacitances, while maintains the rms tank current at near-to-minimum levels. Furthermore, a compensation strategy for the effect of conduction losses is presented achieving better switching behavior and higher efficiency. Compared with the minimum rms current trajectory modulation, lower switching losses, enhanced efficiency, and mitigated voltage ringings are obtained. Effectiveness of the proposed technique is verified by means of a 800 W experimental prototype. Closed-loop operation with the proposed VFM+PSM controller is also implemented and experimentally tested. [ABSTRACT FROM AUTHOR]

This paper presents a method that overcomes the problem of the confusion during fast irradiance change in the classical maximum power point tracking (MPPT) as well as in model predictive control (MPC)-based MPPTs available in the literature. The previously introduced MPC-based MPPTs take into account the model of the converter only, which make them prone to the drift during fast environmental conditions. Therefore, the model of the photovoltaic (PV) array is also considered in the proposed algorithm, which allows it to be prompt during rapid environmental condition changes. It takes into account multiple previous samples of power, and based on that is able to take the correct tracking decision when the predicted and measured power differ (in case of drift issue). After the tracking decision is taken, it will be sent to a second part of the algorithm as a reference. The second part is used for following the reference provided by the first part, where the pulses are sent directly to the converter, without a modulator or a linear controller. The proposed technique is validated experimentally by using a buck converter, fed by a PV simulator. The tracking efficiency is evaluated according to EN50530 standard in static and dynamic conditions. The experimental results show that the proposed MPC-MPPT is a quick and accurate tracker under very fast changing irradiance, while maintaining high tracking efficiency even under very low irradiance. [ABSTRACT FROM AUTHOR]

This paper proposes a voltage-source parallel resonant Class E inverter. The proposed circuit has a shunt capacitor including parasitic capacitance of a switching device and achieves zero-voltage switching and zero-voltage derivative switching at turning-on like a classical Class E inverter. Therefore, high power conversion efficiency is achieved under high operating frequency. Unlike the other Class E inverters, the proposed circuit has no choke inductor or dc blocking capacitor. Moreover, it has a parallel resonant tank unlike the classical Class E inverter. Thus, a circuit protection is not required in a wireless power transfer system. Circuit analysis, circuit simulations, and circuit experiments were carried out. The experimental circuit performed the desired operation and the power conversion efficiency was 93.2% with the output power 4.76 W at the operating frequency 1 MHz. [ABSTRACT FROM AUTHOR]

In order to provide high and extendable power levels for inductive power transfer (IPT) system, a parallel multi-inverter system based on modular inverter is presented. Various power requirements can be implemented by an adjustment of the number of paralleled inverters, which provides a high modularity. A master−slave scheme is employed for the switching-driver signals of parallel inverters, where one acts as a leader while others act as followers. Despite the master−slave scheme, the proposed circuit topology has natural robustness because of the equality in terms of the hardware configuration of each modular inverter. For proper parameters, the output phase (current lagging corresponding voltage) of an inverter is lower than the average of output phase of all inverters, when its output voltage lags behind others, and vice versa. Based on this approach, PI controllers are designed to implement phase synchronization for output voltages of all inverters. An IPT prototype supplied by the proposed parallel multi-inverter with three inverters was designed, built, and tested. Experiments show that the proposed parallel multi-inverter system has not only good circulating current suppression capacity but also excellent performance of phase synchronization. The maximum dc−dc efficiency was 94% at a 35.1 kW receiving power. This paper is accompanied by a Matlab/Simulink file demonstrating phase synchronization control. [ABSTRACT FROM AUTHOR]

This paper presents a multi-period frame transient switching control (MP-TSC) scheme for buck converter with a controlled coupled inductor, aiming at improving the load transient response. The proposed buck converter utilizes a controlled coupled inductor as the output inductor. During a load transient, the coupled inductor is controlled as a small equivalent inductance so as to achieve fast transient regulation. While in the steady state, the coupled inductor behaves as a large inductance to reduce the output current ripple. Furthermore, on the basis of the proposed variable inductance circuit, an MP-TSC control scheme is proposed and implemented in a digital form. With the proposed control scheme, the load transient event is divided into n + 1 sub-periods, and in each sub-period, the capacitor-charge balance principle is used to determine the switching time sequence. Moreover, the control principle design and transient response index analysis are provided. Furthermore, its feasibility is validated in simulation and experiment with a 12–3.3V low-voltage high-current synchronous buck converter. Experimental results demonstrate that the voltage deviation of the proposed MP-TSC scheme (coupled coefficient of the controlled coupled inductor is 0.52) has improved by more than 79% compared to that with the auxiliary circuit disabled. [ABSTRACT FROM AUTHOR]

An improved bridgeless (BL) Cuk converter-based electric vehicle (EV) battery charger with high power factor and increased efficiency is designed and developed in this paper. It provides low cost and high-power-density-based charging solution for the EV. This charger incorporates less number of devices operating over one switching cycle, which reduces the additional conduction loss incurred by a diode bridge rectifier of the conventional charger. Hence, it improves the charger's efficiency. The added advantage of the proposed topology is that the unwanted capacitive coupling loop is removed, as well as the unwanted conduction through the body diode of the inactive switch in the previously developed BL Cuk converter is avoided. This significantly improves the charger's efficiency. For the constant current and constant voltage charging, the commands are synchronized by a flyback converter. The proposed charger draws a sinusoidal current from ac mains and the total harmonic distortion in the supply current is reduced to the limits specified by the IEC 61000-3-2 guidelines. The improved efficiency and power quality indices of the proposed charger are investigated to demonstrate its satisfactory charging operation at all operating conditions. [ABSTRACT FROM AUTHOR]

This paper presents a novel switch current stress reduction technique for a single switch boost-flyback high step up dc–dc converter. Coupled inductor-based converters do not have a sufficiently higher inductance value of their windings. This creates current surge during transient and steady state, which in turn increases current stress at main switch. To compensate this difficulty in coupled inductor-based boost flyback converter, an inductor–diode parallel combination has been connected in series with the switch. This technique increases the effective inductance of the coupled inductor primary winding during switch turn-on operation and helps to reduce current stress. Steady-state operating principle with the proposed technique is analyzed in continuous conduction mode. The current reduction technique is discussed with a proper mathematical derivation. To verify theoretical findings, simulation study is carried out in MATLAB/Simulink R2014b. Finally, a laboratory-based 40-W prototype converter is designed to show the effectiveness of the proposed switch current reduction technique. [ABSTRACT FROM AUTHOR]

A new transformerless bidirectional buck-boost converter is proposed in this paper. The proposed converter has a simple circuit structure, low component count, low voltage stress on the power transistors, and a wide voltage gain range. This makes it applicable in the energy storage charge/discharge systems, such as electric vehicles (EV), microgrids and nanogrids with energy storage units, and uninterruptible power supplies. In addition, synchronous rectification between the complementary transistors is employed to improve the converter efficiency. A comprehensive analysis of the steady-state operation, small-signal model, component parameters design, and efficiency analysis of the proposed converter operating in a continuous conduction mode is given. Finally, a 1.6-kW scaled-down prototype was built using Silicon Carbide MOSFETS to validate the effectiveness and feasibility of the proposed converter. [ABSTRACT FROM AUTHOR]

In this paper, a novel noncoupled inductor high voltage gain single-ended primary-inductor converter (SEPIC) is presented. The proposed converter has various advantages, such as lower voltage stress on the switches, noninverting output voltage, high efficiency, and high voltage gain. Also, the introduced converter has a continuous input current which makes it suitable for renewable energy and fuel cell applications. Moreover, high voltage gain is achieved without using any transformer and coupled inductor, thus there is not any voltage overshoot for the switches during the turn-off process. This effect allows low conduction losses by using lower voltage rating switches and also additional clamping circuit is not needed. The control system of the presented converter is simple and the converter can be easily controlled in continuous conduction mode mode operation. Because, the gating pulses for both of the switches are the same and wide output voltage range is achieved only by changing the duty cycle. Furthermore, the number of the components compared to the other noncoupled inductor, SEPIC-based converters which provide near voltage gain to the proposed converter, is reduced. The detailed operation of the introduced converter and design considerations are discussed. Experimental results are presented to verify the performance of the proposed dc–dc converter. [ABSTRACT FROM AUTHOR]

In this paper, a cooperative triple-phase-shift (CTPS) control for the isolated dual active bridge dc–dc converter is proposed first to eliminate the dual-dc side flow back currents. Furthermore, the current characteristics of the proposed CTPS control with the main variable (the primary side inner phase shift) tuned in two different regions are derived in detail and compared with each other. The tuning region of the main variable with the optimal current characteristics is finally determined based on the comparison results. As a result, the current stress is reduced and the efficiency is enhanced. The detailed experimental results of CTPS control verify its validity and practicability. The advantages of CTPS control are also highlighted by comparing it with some conventional phase shift controls. [ABSTRACT FROM AUTHOR]

This paper discussed an active-bridge-active-clamp (ABAC) topology that is suitable for highpower more-electric-aircraft applications. Though conventional modulation techniques can be applied to ABAC converters, they present drawbacks, such as increased low-voltage (LV) current ripple and limited power transfer capability. To address these problems, a phase-shift-modulation (PSM) scheme is proposed to provide clean dc terminal current at the LV side while maintaining high power transfer capability and efficiency in a wide operating range. The proposed PSM has a complete switching harmonics cancellation on the LV terminals independent of the operating conditions. This results in high quality power without any ac components, thus minimizing passive filtering. In addition, when terminal voltages vary from their nominal values, the proposed PSM can improve the maximum power transfer capability of the ABAC converter compared to the conventional approach. The theoretical claims are validated by both simulation and experimental results on a 10-kW 270-V/28-V ABAC converter. [ABSTRACT FROM AUTHOR]

In this paper, a new zero-voltage zero-current transition (ZVZCT) boost converter using coupled inductors is proposed. The feature of this topology is: the main switch can be switched on with ZVZCT, and off with zero-voltage switching, without any voltage and current stress. The auxiliary switch is turned on with zero-current switching. Other semiconductor devices can also achieve soft switching (SS). Due to the existence of the coupling effect, the current impact of the auxiliary switch is completely suppressed when it is turned off. Lower input current and output voltage in the interval of the switch-off for the auxiliary switch are just equivalent to running at a low power level, which is an additional advantage of the coupled inductor ZVZCT solution. Another advantage of the topology is that the SS condition of the main switch for each specific load can be effectively optimized just by setting the ratio of coupling inductance corresponding to the circuit design and application load. Thus, the topology design can be improved to adapt to different load types. A 100 kHz experimental prototype has been verified, different load for 1 and 0.4 kW optimization comparison has been presented, and the case without optimization is also observed. [ABSTRACT FROM AUTHOR]

In the applications such as mixed-color light emitting diode (LED) lighting system, LED drivers are always required to provide constant current for each LED string and each current should be controlled independently. For this purpose, a single-stage series-type LED driver with independent control of N-channel output currents is proposed in this paper. The function of power factor correction can be realized inherently to obtain high power factor. N active output units, each one made up of a power switch, a diode, and an output filter capacitor, are series-connected to form the series-type N-channel outputs structure. According to different current reference values, N-channel output currents can be independently regulated just by sampling each output current to adjust the duty cycle of each secondary output-switch automatically. The operating principle and independent closed-loop control strategy of the proposed LED driver with N = 3 are analyzed as an example in detail. Finally, the quantitative parameter design method for a 120 W prototype is elaborated. And, the experimental results are presented to verify the effectiveness of the LED driver and the correctness of parameter design method. [ABSTRACT FROM AUTHOR]

Modules with series and parallel connectivity add new features and operation modes to modular multilevel converters (MMCs). Compared to full- and half-bridges, the series/parallel modules allow sensorless module balancing and reduce conduction loss with the same semiconductor area. However, in high-voltage applications with limited switching rates, the sensorless operation of the series/parallel modules suffers from large charge-balancing currents. This paper introduces a series/parallel module variant with a small port inductor. The port inductor suppresses the charge-balancing current despite low switching rates. We also propose a carrier-based modulation framework and show the importance of the carrier assignment in terms of efficiency and balancing. The proposed module and the modulation method are verified on a lab setup with module switching rates down to 200 Hz. The module voltages are kept within a narrow band with the charge-balancing currents below 5% of the arm current. The experimental results show practicality and advantages of the new series/parallel modules in high-voltage MMC applications. [ABSTRACT FROM AUTHOR]

The magnetic resonant wireless power transfer (WPT) system with a class E inverter has wide application in mid-range power transmission, especially for several megahertz scenario. However, it is cumbersome for the existing modeling and analysis methods to obtain the analytical solution to the system variables, which limits the evaluation of system characteristic. This paper proposes a nonlinear mathematical model for the WPT system with a class E inverter. The equivalent small parameter method (ESPM) is first adopted to solve the proposed six-order nonlinear model, and symbolic-form steady-state periodic solutions are yielded. During the whole solving process, only three iteration steps are needed for the proposed method. Compared with other existing modeling and analysis methods, the symbolic periodic results acquired by the ESPM exhibit sufficient accuracy by virtue of the combination of more higher harmonics. Meanwhile, the calculation complexity is simplified remarkably. Simulation and available experiments validate the effectiveness and accuracy of the proposed method. [ABSTRACT FROM AUTHOR]

In this paper, a fully soft-switched bidirectional dc–dc converter is proposed. All semiconductor devices are soft switched, while its control circuit remains pulsewidth modulated. This condition is achieved only by one auxiliary switch. So, the proposed topology has less complexity in comparison with other similar structures. The energy conversion through the proposed topology during buck and boost modes is highly efficient due to achieved soft-switching condition. The auxiliary circuit operates once during each switching cycle. The converter is analyzed and a 250-W laboratory prototype of the proposed converter is constructed. The experimental results are presented that confirm the theoretical analysis. [ABSTRACT FROM AUTHOR]

In this paper, a generalized switching modification method is proposed to reduce the root-mean-square (rms) current flowing into a dc-link capacitor in a dc–dc–ac structure consisting of a boost converter and a three-phase inverter. To analyze the current flowing into the capacitor, we analyze the currents at the respective converter and inverter sides. Based on this analysis, we derive an analytical method to find the modification time between the converter and inverter pulsewidth modulation (PWM) carriers through a Fourier series and approximation to facilitate real-time implementation. Real-time implementation of the modification time calculated by the derived method is described. To verify the validity of the proposed method, experimental results are presented based on a 1-kVA dc–dc–ac prototype. The proposed method has a better capacitor rms current reduction performance than the conventional method in various inverter power factors and PWM strategies. Especially, it has an excellent performance in mid-power factor level (0.95–0.1). [ABSTRACT FROM AUTHOR]

This paper proposes two coupled-inductors-based Z-source networks, called the modified series and tapped switched-coupled-inductors quasi-Z-source networks (mSSCL-qZSN and mTSCL-qZSN, respectively). These networks offer high voltage gains with less-than-unity winding turn ratios $(n < {\text{1)}}$ , resulting in a reduced inductive element size. Other advantages include a less number of active components and their lower ratings and a higher efficiency. In addition, a lower magnetic core size is required for the proposed ZSNs due to the lower peak magnetizing current. The performance principles and detailed comparative analysis are provided and confirmed through experiments on a 200-W dc–dc converter. [ABSTRACT FROM AUTHOR]

Most fuel cell electric vehicles require wide voltage-gain DC–DC converters to increase and equalize the relatively low voltage of fuel cell stacks with DC link bus or energy-storage devices, such as supercapacitors or batteries. This paper proposes two new non-isolated DC–DC converters suitable for such applications, which can be extended to other electric vehicles as well. The proposed converters combine the main characteristics of both quadratic Boost and Ćuk converters, offering high step-up voltage and control simplicity using only one ground referenced active power switch. Additionally, the proposed topologies present reduced voltage stress across the active power switch when compared to other boost converters. Considerations about the design of the proposed converters will also be presented. Experimental results obtained using a laboratory prototype validate the effectiveness and feasibility of the proposed topologies and its suitability for fuel cell electric vehicles. [ABSTRACT FROM AUTHOR]

This paper presents a generalized analysis of the Class-E power amplifier (PA) with a shunt capacitance and a shunt filter, leading to a revelation of a unique design flexibility that can be exploited either to extend the maximum operating frequency of the PA or to allow the use of larger active devices with higher power handling capability. The proposed PA fulfills zero voltage switching (ZVS) and zero voltage derivative switching (ZVDS) conditions, resulting in a theoretical dc-to-RF efficiency of 100%. Explicit design equations for the load-network parameters are derived, and the analytical results are confirmed by harmonic-balance simulations. Two PA prototypes were constructed with one designed at low frequency and the other at high frequency. The first PA, which employs a MOSFET and a lumped-element load-network, delivered a peak drain efficiency $(\!D\!E)$ of 93.3% and a peak output power of 37 dBm at 1 MHz. The second PA, which employs a GaN HEMT and a transmission-line (TL) load-network to provide the drain of the transistor with the required load impedances at the fundamental frequency as well as even and odd harmonic frequencies, delivered a peak $D\!E$ of 90.2% and a peak output power of 39.8 dBm at 1.37 GHz. [ABSTRACT FROM AUTHOR]

The Class E dc–dc converter, with a simple topology and zero-voltage-switching (ZVS) for the power switch, can operate at a switching frequency of up to megahertz. In this paper, an optimized ZVS operation condition for minimizing the switch voltage stress, switch rms current, and switch voltage harmonic components is derived for the on‐off controlled Class E dc–dc converter by optimizing the time instant at which the switch voltage resonates back to zero. Based on this result, a step-by-step parameter design approach is proposed for a Class E dc–dc converter with a large input inductor, which avoids time-consuming simulations or complex numerical calculations. Then, a capacitance compensation approach is further proposed to extend the design results to a Class E dc–dc converter with a resonant input inductor. Furthermore, an adaptive duty-cycle adjustment scheme is proposed for reducing the reverse conduction loss of the power switch, thereby improving the conversion efficiency over the entire input voltage range. Finally, a prototype of a 20-MHz 10-W Class E dc–dc converter is built and tested in the laboratory, and experimental results are presented to verify the effectiveness of the proposed optimized parameter design approach and the adaptive duty-cycle adjustment scheme. [ABSTRACT FROM AUTHOR]

This paper describes a novel family of single-phase single-stage buck–boost inverters using output unfolding circuits. Operation principles and component design guidelines along with modulation techniques are presented and discussed. The simulation results confirm all theoretical statements. Experimental setup of the most promising solution is assembled and tested, where the efficiency for different operation modes is analyzed. Finally, the pros and cons along with applications of the proposed solutions are discussed in the conclusions. [ABSTRACT FROM AUTHOR]

In high gain voltage conversion applications, the low-side switches usually suffer large current stress, resulting in dominate switching loss. In this paper, a general soft-switching method based on an advanced interleaved high-step-up converter, which features excellent performance but works in hard-switching, is presented to combat this issue by using a plug-play resonant circuit. Under this soft-switching method, the main switches reach zero-voltage switching (ZVS) turn-on and ZVS turn-off, and the soft-switching condition is derived. Meanwhile, the added auxiliary switches could be turned off under ZVS condition and turned on under zero-current switching condition as well. More importantly, due to its location out of the energy transferring path, the auxiliary circuit will never lead gain lost to the converter and maintain its other existing merits, such as current auto-balancing and diode inverse-recovery well. A 1-kW prototype is built and tested to verify the significant efficiency improvement and merits maintenance for the proposed converter considering active resonant soft switching. [ABSTRACT FROM AUTHOR]

This paper investigates basic stability properties of the three-level flying-capacitor Buck converter when operated under current-mode control (CMC). The proposed analysis is developed for both peak CMC (P-CMC) and valley CMC (V-CMC), and addresses both the static instability of the inductor current and the flying capacitor (FC) voltage runaway phenomenon. Conditions for avoiding current subharmonic oscillations are derived first, along with the expressions of the minimal compensation ramp, which guarantee current stability throughout the entire operating range. As for the stability of the FC voltage, P-CMC results to be inherently unstable unless the converter operates with a relatively large peak-to-peak inductor-current ripple, a feature not yet recognized in the literature. However, V-CMC results to be inherently stable once the static instability of the current is eliminated with an external compensating ramp—a property that has been highlighted in the literature but never formally proven. The proposed analysis is verified both using a simulation model and experimentally using a 3.3-V, 500-mA, 500-kHz prototype. [ABSTRACT FROM AUTHOR]

The class-E shunt inductor inverter (SII) topology typically operates based on zero-current switching (ZCS) and zero-derivative current switching (ZDCS) conditions. Based on these terms, the peak switch voltage and load resistance are eliminated as the major limitation parameters to implement the class-E SII with the desired design specifications. This paper introduces the design and analysis of the class-E SII with the specified deviation from both ZCS and ZDCS conditions. Therefore, 2 degrees of the design freedom are obtained. Two new parameters that are normalized by the dc-supply current are defined in terms of the deviation from ZCS, i.e., $\alpha $ and ZDCS, i.e., $\beta $. This operation mode of class-E SII is named as the nonzero current. The performance characteristics and design relationships are obtained in terms of the phase shift between the input and output voltages. The demonstration of the proposed operation mode is proven by fabrication of a prototype circuit with output power 10 W at 4-MHz operating frequency and close agreement between experimental outcomes with the simulation and theoretical results. [ABSTRACT FROM AUTHOR]

Because it possesses higher current turn-off capability, the inverse current commutation with semiconductor devices (ICCOS) is a better option for the opening switch of an inductive pulsed power supply than the integrated gate commutated thyristor. This paper investigates the counter-current capacitor, which is the key component that determines the turn-off result and the volume of the counter-current branch. The major contributions of this paper include the following: 1) deriving an analytical expression for the minimum precharged capacitor voltage that can reliably turn off the main switch; 2) verifying this expression through a series of experiments within a current range of 0 to 4000 A and an energy range of 0 to 50 kJ; 3) giving an approximate expression for the optimal capacitance that minimizes the precharged energy; and 4) investigating the variation trends of the optimal capacitance and the corresponding optimal precharged energy with varying inductor current. [ABSTRACT FROM PUBLISHER]

Superconducting pulsed-power supply (SPPS) provides an efficient method for both high-density inductive energy storage and high current pulse generation. An SPPS consisting of eight high-temperature superconducting pulsed-power transformer (HTSPPT) modules with XRAM methodology was designed and simulated in preliminary studies. It recycled the leakage flux energy and reduced the voltage across the opening switch with a capacitor in primary. However, the SPPS with XRAM methodology has two problems. The first one is that it can provide high pulse amplitude, but cannot provide enough width. The other one is that the ratio of the maximum capacitive energy over the total inductive energy is relatively large, which cuts down the overall system energy density. This paper proposes a modified topology of SPPS with capacitor reuse methodology. Multiple HTSPPT modules are divided into several groups. Each group shares the same capacitor. The procedure of the modified SPPS is presented in detail. A 270-kJ SPPS with capacitor reuse methodology is designed and simulated to illustrate the modified topology. With the load parameters of a small railgun, the peak value of the load current is 207.15 kA and the pulse half-height width is 5.56 ms, the ratio of the maximum capacitive energy over the total inductive energy is 11%. The characteristics of the modified topology are also described in detail in this paper. [ABSTRACT FROM PUBLISHER]

Condition monitoring of aluminum electrolytic capacitors (AECs) is essential for predictive maintenance of power electronic converters. The AEC is considered at the end of its life when its capacitance or equivalent series resistance (ESR) reaches corresponding critical values. In the literature, it is found that either of these parameters may reach its critical limit depending on the operating conditions and applications. However, most of the existing health monitoring techniques of the AEC in dc–dc converters are based on the estimation of ESR. To address the aforementioned issue, this paper proposes to estimate the low-frequency impedance of the AEC, which is dominated by its capacitance value, thereby allowing health monitoring based on the capacitance value. The technique is based on injection of a low-frequency current ripple into the AEC using duty ratio control of the dc–dc converter. The parameters of new and aged capacitors are experimentally obtained at various temperatures and are used to establish the failure criteria. Furthermore, the proposed method is applicable for both the continuous conduction mode and the discontinuous conduction mode (DCM) of operation. For DCM operation, a sampling instant to recover a low-frequency waveform is suggested based on mathematical analysis. Detailed simulation studies are performed and results are included in this paper. Experimentation is carried out on a dc–dc boost converter integrating solar photovoltaic with the dc system. Experimental results are found to be in agreement with simulation results. [ABSTRACT FROM PUBLISHER]

This part of the paper illustrates the use of the expression derived in Part I for predicting subharmonic oscillation in switching regulators. Six case studies with different control schemes from the recent literature are used to validate the novel approach and the new derived expression, which is benchmarked for these case studies against results obtained using the discrete-time modeling approach or Floquet theory combined with Filippov method. Numerical simulations from the circuit-level switched models, implemented in PSIM software, are used to demonstrate the correctness of the derived closed-form condition. A procedure is presented to apply the approach of the paper to power converters with nonlinear sources, such as photovoltaic (PV) arrays or fuel cells. Experimental measurements from a boost converter prototype for PV applications are also provided to validate the theoretical predictions and the numerical simulations showing a remarkable agreement. [ABSTRACT FROM AUTHOR]

This paper proposed a new half-bridge (HB) LLC resonant converter family with pulse-width modulated (PWM) auxiliary switch (sLLC converter) for hold-up mode operation. The proposed sLLC converters could operate with synchronous rectifier, which is suitable for low-output voltage applications. In the proposed converters, an auxiliary switch is added at the primary side to provide charging path for the series resonant inductor. For nominal 400-V input, sLLC achieves same performance as conventional LLC converter, and all the good features such as soft switching are naturally retained. For slight input voltage fluctuation, frequency modulation is used to regulate the output voltage. When the input voltage reduces further, HB switches will operate at constant minimum frequency, and the auxiliary switch will operate in the PWM mode to energize the resonant inductor with the bus voltage directly during hold-up period. Thus, the converter achieves higher voltage gain, and the output voltage can be maintained at desired level. To verify the effectiveness of the proposed sLLC converter, operational principle and equivalent circuits will be carefully explained and analyzed in this paper. A 300-W prototype is built for 250–400-V input 12-V output application. [ABSTRACT FROM AUTHOR]

Usually, the high-gain high-efficiency dc–dc converters consist of many passive components, which increases the order of the system. As the order increases, system modeling and control become more complex. Thus, there is a need for the simplification of the small signal modeling process of such converters. This paper presents a generalized small signal model and equivalent circuit for an $n$ th-order coupled-inductor-based high-voltage gain converters (CIHVGC) that can be conveniently used for the control design. The state variable representation of a generalized coupled inductor with p windings is included. A simplified step by step procedure to obtain small signal model using visual inspection is presented. Analysis is included and verified using simulations and experiments for the output voltage regulation of high-voltage gain converters. The usefulness and versatility of the proposed model is verified with three examples of high gain converters belonging to the CIHVGC family. All the analytical, simulation, and experimental details of this paper are presented. [ABSTRACT FROM AUTHOR]

For the conventional PFC rectifiers, the high efficiency cannot be achieved over a wide input range, and the efficiency will be greatly decreased at low-input voltages. In order to overcome the efficiency bottleneck under low-line input, a flexible mode bridgeless boost power factor correction (PFC) rectifier is proposed in this paper. According to the input voltage, the proposed rectifier can be flexibly adapted to the suitable operating mode to obtain the maximum efficiency. Meanwhile, the circuit components can be reused by different operating modes, so the extra cost is low. In the proposed rectifier, a back-to-back bridgeless boost PFC topology is adopted at high-line conditions and a three-level bridgeless boost PFC topology is rebuilt to reduce the switching losses at low-line conditions. Compared with the traditional bridgeless boost PFC rectifier, an extra low-voltage bidirectional switch (usually composed of two switches) is added, so the increased cost is low. In addition, the low common-mode noise can be achieved at both high- and low-line conditions due to the direct connection between the input mains and the output electrolytic capacitor. The detailed principle analysis about the proposed rectifier is presented in this paper. Finally, an experimental prototype is built to verify the feasibility and the effectiveness of the proposed topology. [ABSTRACT FROM AUTHOR]

A new active-clamped zero-voltage switching (ZVS) push–pull converter is proposed in this paper. Compared with the conventional push–pull converter, one auxiliary switch $Q_{{3}} and a clamping capacitor Ca are added in the primary side of the transformer to recycle the energy stored in the leakage inductors and clamp the voltage spike. Owing to the proposed converter which maintains ZVS of all the three switches from full load to very light-load condition, switching losses are reduced significantly. The voltage across the switch can be clamped at the input voltage plus the clamping capacitor voltage, i.e., V\rm{in}{+}VCa, are much less than those of a conventional push–pull converter that enabling the use of low-voltage, low-performance, and low-cost devices. In addition, the proposed topology can eliminate the problems of flux imbalance existing in the conventional one. Detailed operation, analysis, design, comparative study, and experimental results for the proposed converter are presented in this paper. An 800 W prototype was developed in the laboratory to evaluate and demonstrate the validity of the converter. [ABSTRACT FROM AUTHOR]

This paper proposes a novel single-switch dc/dc converter for the future renewable electric energy delivery and management system to implement the distributed renewable energy resources (DRER). The DRER is responsible for the maximum power point tracking of the photovoltaic panel (PV) module and also for the control of central energy storage device. Due to the characteristics of the PV module and the dc-bus, the single power stage must provide low current ripple in the input and output terminals, must operate with output current and voltage regulation, and present a high-voltage conversion ratio. To achieve such features, this paper proposes a novel integrated Boost–Zeta converter. To avoid a complex modeling and control, we propose a disaggregation concept for this. Experimental results are presented for the purpose of operating the converter and also for the operation of the system. [ABSTRACT FROM PUBLISHER]

In this paper, a new soft switching flyback dc–dc converter with a simple zero-voltage and zero-current switching (ZVZCS) cell is proposed. The auxiliary resonant cell consists of one switch, one diode, one inductor, and two capacitors. It provides ZVZCS not only for the main switch but also for the auxiliary switch at both turn-on and turn-off times. In addition, all the auxiliary diodes and body diodes of the switches operate under full ZVZCS except the output diode which turns off only with zero current switching. This soft switching technique makes the proposed converter have less switching losses which leads the converter to operate in higher frequencies and efficiency. Another outstanding feature of the proposed converter is using the auxiliary resonant cell out of the main power path to have lower voltage stress on the switches. In this paper, pulse width modulation (PWM) is employed to control the main switch. A detailed mode analysis of the proposed converter operation is presented along with design procedure. Finally, the accuracy performance of the converter is verified through a 60 W experimental prototype results. [ABSTRACT FROM AUTHOR]