Search

In data center and telecommunication power supplies, the front-end dc–dc stage is required to operate with a wide input voltage range to provide hold-up time when ac input fails. Conventional LLC converter serving as the dc–dc stage is not suitable for this requirement, as the normal operation efficiency (at 400 V input) will be penalized once the converter is designed to achieve high peak gain (wide input voltage range). This paper examined the operation of the LCLC converter and revealed that the LCLC converter could be essentially equivalent to a set of LLC converters with different magnetizing inductors that are automatically adjusted for different input voltages. In nominal 400 V input operation, the LCLC converter behaves like an LLC converter with large magnetizing inductor, thus the resonant current is small. In the hold-up period, when the input voltage reduces, the equivalent magnetizing inductor will reduce together with switching frequency reducing, thus the converter achieves high peak gain. In this paper, a new design methodology is also proposed to achieve optimal utilization of the two resonant capacitors for high power application. To verify the effectiveness of the LCLC converter for hold-up operation, comprehensive analysis has been conducted; a detailed step by step design example based on capacitor voltage stress is introduced; an experimental LCLC prototype optimized at 400 V, with input voltage range of 250–400 V and 12 V/500 W as output has been presented. [ABSTRACT FROM AUTHOR]

Modular multilevel converter (MMC) has been a promising candidate in high voltage direct current (HVdc) transmission systems. Due to the features of simple structure, low cost, and low power losses, half-bridge (HB) is usually adopted as the submodule circuit in the traditional MMC. However, an HB submodule circuit-based MMC does not have the capability of blocking dc short-circuit fault, which obstructs the development of low-cost HVdc systems with overhead lines. In order to solve this problem, an MMC with active clamped T-type submodule (ACTSM) to own dc fault blocking capability is proposed in this paper. Compared with other submodule circuits, the proposed ACTSM has many features, such as symmetrical blocking capability, low power losses, low voltage stress, and low amount of independent drive signals. The topology, operation principle, dc fault blocking capability, and distribution of power losses of the ACTSM are presented in this paper. The effectiveness of the ACTSM-based MMC is validated by both simulations and experiments. [ABSTRACT FROM AUTHOR]

The paper deals with some new results on the averaging theory approach for the analysis of feedback controlled pulsewidth modulation power electronic converters. It develops some considerations regarding the averaging approximation of time-variant differential systems proving an analytical relationship between the accuracy with which the solution of the averaged model converges to the solution of the original time-variant model (i.e., the switched model) and the switching frequency of the converters. This relation is valid both for stable and unstable systems. Moreover, this paper confirms, as corollary, that under suitable conditions (verified during the standard operations of the power electronic converters) the averaged model uniformly converges to the switched model. [ABSTRACT FROM AUTHOR]

This paper proposes a new modulated model predictive control method for the control of modular multilevel converters (MMCs) in voltage source converter-high voltage dc systems. The proposed method retains the advantages of the conventional finite control set-model predictive control methods by programing the nonlinear properties of the MMC into the design calculations while minimizing the ac line and circulating current ripples and steady-state error by generating modulated switching signals with a fixed switching frequency. In this paper, first, the predictive modeling of the MMC is provided. Next, the proposed control method is described. Then, the application of the proposed method to an MMC system is detailed. Finally, experimental results from an MMC system connected to a three-phase grid are provided to validate the theoretical outcomes. [ABSTRACT FROM AUTHOR]

Superjunction MOSFETs in cascode configuration with low-voltage silicon MOSFETs are evaluated in this paper. The proposed structure combines the good switching performance provided by the cascode configuration with the benefits of the silicon technology such as its robustness, maturity, and low cost. This paper aims to explain and to demonstrate the reduction of switching losses of superjunction MOSFETs in cascode configuration with respect to their standalone counterparts (directly driven). A detailed simulation analysis of power loss contributions is carried out under hard-switching operation. Moreover, experimental evidence is provided using a boost converter (100–400 V) operating in continuous conduction mode for different switching frequencies (100–400 kHz) and output power levels (180–500 W). [ABSTRACT FROM AUTHOR]

The modeling and control of a buck–boost and stacked dual half-bridge (DHB) integrated bidirectional dc–dc converter have been studied in this paper. This converter features high-voltage transfer ratio, high efficiency, and the minimum number of switches. In this paper, an extended, continuous, full-order, state-space averaging modeling method is proposed. Compared with existing methods, the proposed method exhibits higher coincidence with the switching circuit simulation, in steady and especially dynamic states. Due to its high dynamic accuracy and low complexity, the proposed modeling method provides a better theoretical analysis and a fast simulation tool for transient process and control design of converters with dual-active-bridge units, especially with DHB units. By using this method, the high-frequency transformer series inductance current is directly divided into a sampled dc component and a fluctuant component. Only the sampled dc one is included into state variables, but both components are considered into state equations. Besides, this method regards the entire converter as a linear superposition of its subsections, which provides a stepwise modeling based on linearization of subsections. Moreover, a decoupled proportional-integral control method is proposed to enhance the stability and dynamic response of the converter. This control method is analyzed by the proposed models, which can be regarded as an application of the proposed modeling method. Simulation and experiments have validated both the proposed modeling and the decoupled control strategy. [ABSTRACT FROM PUBLISHER]

This paper introduces a novel five-level nested neutral point piloted (NNPP) converter and analyzes the operating principle of five-level NNPP converter. This paper presents a novel space vector pulse width modulation (SVPWM) algorithm based on gh coordinate for five-level NNPP converter. First, the common-mode voltage is reduced by choosing the appropriate redundant switching states. After that, the floating-capacitor voltage balance control strategy is presented. The appropriate switch combinations of each phase are determined by the control requirements of floating-capacitor voltages respectively and the hardware mapping method of the switching states is presented. Furthermore, the neutral-point voltage balance control strategy is presented. In order to balance the dc-link capacitor voltages, the seven-segment switching sequence is selected according to the control requirements of dc-link capacitor voltages and the neutral-point voltage regulatory factor is introduced to regulate the durations of the redundant switching states in a switching cycle. Finally, the validity of the novel SVPWM algorithm with decoupling control strategies of floating-capacitor voltages and dc-link capacitor voltages is verified by the experimental results of five-level NNPP converter under steady-state and dynamic conditions. [ABSTRACT FROM AUTHOR]

Photovoltaic (PV) systems having rechargeable batteries are prone to be complex and costly because multiple converters are necessary to individually regulate a load, PV panel, and battery. This paper proposes novel nonisolated multiport converters (MPCs) integrating a bidirectional pulsewidth modulation (PWM) converter and phase-shift-switched capacitor converter (PS-SCC) for standalone PV systems. A PWM converter and PS-SCC are integrated by reducing the total switch count, realizing the simplified system and circuit. In the proposed MPCs, two control freedoms of duty cycle and phase shift angle are manipulated to individually regulate the load, PV panel, and/or battery. The detailed operation analysis was performed to mathematically derive gain characteristics and zero voltage switching operation boundaries. For the battery discharging mode, in which the PV panel is not available and the MPC behaves as a single-input–single-output converter with two control freedoms available, the optimized control scheme achieving the lowest rms current is also proposed to maximize power conversion efficiencies. Various kinds of experimental verification tests using a 200-W prototype were performed to verify the theoretical analysis and to demonstrate the performance of the proposed MPC. [ABSTRACT FROM AUTHOR]

Magnetically coupled impedance-source (MCIS) networks are recently introduced impedance networks intended for various high-boost applications. It employs coupled magnetic in the circuit to achieve higher voltage gain. Various MCIS networks have been proposed in the literature for myriad applications; however, due to effective role of system modeling in the closed-loop controller design, this paper is allocated to small-signal modeling and analysis of MCIS converters. The modeling is performed by means of the circuit averaging and averaged switch technique. A generalized small-signal derivation is demonstrated for pulse width modulation (PWM) MCIS converters and it is shown that the derived transfer functions can simply be applied to Y-source, Γ-source, and T-source impedance networks. Various transfer functions for capacitor voltage, output voltage, magnetizing current, input and output impedance are derived and have been validated through frequency and dynamic responses of computer simulation results. In addition, a comprehensive analysis has been done for all mentioned PWM MCIS converters regarding their circuit parameters. Furthermore, the effect of considering the equivalent series resistances of capacitor and inductor on the stability margin of MCIS converters is revealed in this paper. Finally, in order to validate the derived transfer functions and to consolidate the perfumed analysis, experimental results are presented for all mentioned MCIS converters. [ABSTRACT FROM PUBLISHER]

A dual-input high step-up DC/DC converter with zero voltage turn-off (ZVT) auxiliary circuit is presented in this paper. The cost of whole photovoltaic (PV) power could be decreased significantly by the proposed converter because it allows two PV panels to be connected at the same time. ZVT auxiliary circuit provides soft switching in a wide range of load variations with six passive components. Turn-off switching losses could be decreased and the efficiency of the whole converter could be improved. In , the operation principle and performance characteristics of the proposed converter have been analyzed and an 800 W experimental prototype has been built to validate the analytical results in. In , a dual-input maximum power point tracking (DMPPT) control algorithm has been designed for the proposed converter. Experimental results show that two PV panels can achieve the maximum power output state separately by the proposed DMPPT control algorithm. [ABSTRACT FROM AUTHOR]

In dc microgrid (MG) systems, energy storage systems (ESSs) capable of short- or long-term energy buffering are indispensable for energy management and providing high-quality electric energy. The MG should be able to operate in both islanded and grid-connected modes. A sudden failure of ac utility grids can lead to an inoperable condition of the MG or a large transient phenomenon accompanied by oscillation and overshoot during the mode transition. This paper proposes a control scheme of the bidirectional dc–dc converter for the ESS to resolve the issue associated with mode switching. The proposed control scheme provides autonomous and smooth mode switching, thereby reducing the reliance on the communication with the central controller, and enhancing the reliability of the system. To validate the proposed concept, simulation results and experimental results are provided. [ABSTRACT FROM AUTHOR]

In this paper, a novel platform for the single phase switched-capacitor multilevel inverters (SCMLIs) is presented. It has several advantages over the classical topologies, such as an appropriate boosting property, higher efficiency, lower number of required dc voltage sources, and other accompanying components with less complexity and lower cost. The basic structure of the proposed converter is capable of making nine-level of the output voltage under different kinds of loading conditions. Hereby, by using the same two capacitors paralleled to a single dc source, a switched-capacitor (SC) cell is made that contributes to boosting the value of the input voltage. In this case, the balanced voltage of the capacitors can be precisely provided on the basis of the series–parallel technique and the redundant switching states. Afterward, to reach the higher number of output voltage levels, two suggested SC cells are connected to each other with a new extended configuration. Therefore, by the use of a reasonable number of required power electronic devices, and also by utilizing only two isolated dc voltage sources, which their magnitudes can be designed based on either symmetric or asymmetric types, a 17- and 49-level of the output voltage are obtained. Based on the proposed extended configuration, a new generalized version of SCMLIs is also derived. To confirm the precise performance of the proposed topologies, apart from the theoretical analysis and a complete comparison, several simulation and experimental results are also given. [ABSTRACT FROM AUTHOR]

A single-phase bridgeless Cuk ac/dc power factor correction (PFC) rectifier with positive output voltage is proposed in this paper. For low output voltage product applications, the rectifier is designed to convert high input voltage to low output voltage. Due to no bridge diodes required and thus decreased input conduction losses, the proposed rectifier efficiency can be improved. The proposed rectifier operates in discontinuous conduction mode, and the current-loop circuit is hence not needed. In addition, only a single switch is used in the rectifier to simplify the control circuit design. A simple translation method to have the positive output voltage in the Cuk converter is presented in the rectifier to reduce the component counts and the cost. The operational principles, steady-state analysis, and design procedure of the proposed rectifier are addressed in detail in this paper. Simulation and experimental results obtained from a 150-W rated prototype circuit with input of 90–130 Vrms, 60 Hz, and output of 48 Vdc have verified the validity of the proposed rectifier. [ABSTRACT FROM PUBLISHER]

This paper presents a generalized multilevel direct power control (ML-DPC) scheme for grid-connected multilevel power converters. The proposed method extends the original DPC operating principle by considering only the closest subset of two-level voltage vectors to the present switching state. The implementation of this principle requires the power derivatives for feedback, which can present numerical problems when applied experimentally, mainly due to high measurement noise sensitivity. Therefore, a derivative estimator is proposed based on the converter-grid model in the synchronous reference frame. In addition, a virtual flux observer is developed to achieve synchronization and improve robustness in the presence of grid voltage harmonics. The proposed method is applicable to any multilevel converter topology of any number of levels. In this paper, simulations and experimental results are presented for a seven-level cascaded H-bridge converter. [ABSTRACT FROM AUTHOR]

Automotive point-of-load dc–dc converters have a wide input voltage range from 4.5 to 42 V and, in order to avoid the AM band interference and comply with the strict CISPR-25 standard for electromagnetic interference (EMI) performance, the switching frequency is desired to be higher than 2 MHz. Buck converter is currently employed for such applications owing to its simplicity and low cost, but it has low efficiency at high switching frequencies and high EMI noise emission due to hard switching. A new active-clamp buck converter is proposed in this paper, which features zero-voltage-switching for main and auxiliary switches, and soft turnoff for synchronous rectifier over a wide input voltage range. The detailed operating principle analysis and several important design considerations are presented. Extensive design equations that can be adapted for other specifications and applications are also derived. A 2.2 MHz, 5V/5A prototype converter with only Silicon mosfets has been designed, built, and tested. The experimental results verify the converter operation and demonstrate the superior performance of the proposed active-clamp buck converter. [ABSTRACT FROM PUBLISHER]

This paper proposes a current-mode hysteretic buck converter with a spur-free constant-cycle frequency-hopping controller that fully eliminates spurs from the switching noise spectrum irrespective of variations in the switching frequency and operating conditions. As a result, the need for frequency regulation loops to ensure nonvarying switching frequency (i.e., fixed spurs location) in hysteretic controllers is eliminated. Moreover, compared to frequency regulation loops, the proposed converter offers the advantage of eliminating mixing and interference altogether due to its spur-free operation, and thus, it can be used to power, or to be integrated within noise-sensitive systems while benefiting from the superior dynamic performance of its hysteretic operation. The proposed converter uses dual-sided hysteretic band modulation to eliminate the inductor current imbalance that results from frequency hopping along with the output voltage transients and low-frequency noise floor peaking associated with it. Moreover, a feedforward adaptive hysteretic band controller is proposed to reduce variations in the switching frequency with the input voltage, and an all-digital soft-startup circuit is proposed to control the in-rush current without requiring any off-chip components. The converter is implemented in a 0.35-μm standard CMOS technology and it achieves 92% peak efficiency. [ABSTRACT FROM PUBLISHER]

This paper describes the design of an interleaved sliding mode control for a multiphase synchronous buck converter, which inherits the properties of sliding mode control, operates with fixed switching frequency in the steady-state, and ensures current equalization among phases. Moreover, a power management algorithm is added in order to decide the number of active phases as function of the power load demand, thus optimizing the converter efficiency. The system uses a Master–Slave structure where each phase can actuate as the Master one in such a way that the overall system reliability is improved. Experimental results in a 1.5 kW eight-phase synchronous buck converter show that interleaving operation, robust output voltage regulation, phase current equalization, switching frequency regulation, and power management are achieved. [ABSTRACT FROM PUBLISHER]

This paper presents a multiobjective real-time controller for a modular multilevel converter capable of parallel module connectivity, the so-called modular multilevel series parallel converter (MMSPC). The MMSPC topology allows the batteries to be dynamically rewired in various series–parallel configurations, generating a wide range of output voltage levels. The novel control method parallelizes the modules to balance their voltages without the need for individual module voltage monitoring. Additionally, the controller optimizes across the large number of feasible system configurations to minimize switching and conduction losses. Finally, the controller efficiently encodes the system configuration with module interconnection states rather than the module switch states, which substantially simplifies control. Furthermore, this work experimentally validates the MMSPC topology and concept. In the prototype, the parallel mode reduced the system losses at 5 kW output power by 18% and 24% for load power factors of 1.0 and 0.8, respectively. Sensorless balancing via parallelization maintained well-matched module voltages (standard deviation = 0.045 V) over a 5-h battery discharge with highly variable load current. The reduced conduction losses and simple balancing capability of the MMSPC can enable new applications at medium and low voltages that benefit from its high-quality output, elimination of filtering magnetics, fast response, and modularity. [ABSTRACT FROM AUTHOR]

Dynamic voltage restorer (DVR) technology has become a mature power quality product. In high-power applications, DVR using a multilevel converter is commonly used. However, DVR using a multilevel direct pulse width modulation (PWM) ac–ac converter has not been well studied. This paper presents a new DVR topology using a cascaded multilevel direct PWM ac–ac converter. In the proposed scheme, the unit cell of the multilevel converter consists of a single-phase PWM ac-ac converter using switching cell structure with coupled inductors. Therefore, the multilevel converter can be short- and open-circuited without damaging the switching devices. Neither lossy RC snubber nor a dedicated soft commutation strategy is required in the proposed DVR. This improves the reliability of the DVR system. The output voltage levels of the multilevel converter increase with the number of cascaded unit cells, and a high ac output voltage is obtained by using low-voltage-rating switching devices. Furthermore, a phase-shifted PWM technique is applied to significantly reduce the size of the output filter inductor. A 1-kW prototype of single-phase DVR is developed, and its performance is experimentally verified. Finally, the simulation results are shown for a three-phase DVR system. [ABSTRACT FROM AUTHOR]

Distributed energy resources (DERs) are expected to provide ancillary functions including reactive power generation and harmonics compensation. Meanwhile, multilevel inverters and two-level converters with optimal pulsewidth modulation (OPWM) will be commonly used for DERs at high power levels. The challenge is to realize harmonic compensation with limited switching angles. This paper presents an online solution to realize the selective harmonics compensation (SHC), and power generation with DERs. For harmonics compensation, the selective harmonic components in the load current are detected. Then, the harmonic voltages are provided with DERs to cancel out these detected components. Since the power converter is requested to realize both harmonics filtering and power generation, limitations on harmonics compensation at the given power are discussed. Power hardware-in-the-loop-based online verifications are shown at the end of the paper. [ABSTRACT FROM AUTHOR]

The five-level active neutral-point-clamped (5L-ANPC) converter has been widely studied for its excellent performance in high-power medium-voltage applications. This paper analyzes the space vector pulse width modulation (SVPWM) strategy of the 5L-ANPC converter in the virtual coordinate, and presents an optimized control strategy which can balance the neutral point (NP) voltage and avoid the dead-time effects for the first time. In this strategy, on one hand, the 125 space vectors are combined by 96 triangles in the seven-segment vector synthesis method, then the triangles are divided into seven categories which have different characteristics of balancing the NP voltage, and every category has its own principles to choose the vector sequence and compute the vector durations. On the other hand, the dead-time effects of the 5L-ANPC converter are studied in detail and the transitions between different switching states are constrained in the optimized control strategy to avoid the dead-time effects that cannot be compensated by traditional pulse-based dead-time compensation methods. Finally, the optimized SVPWM strategy is experimentally verified in this paper. [ABSTRACT FROM AUTHOR]

A recently reported modeling methods for a switched capacitor converter either assume output as “firm” voltage or a resistor to facilitate calculation. When the size of output filter capacitor is moderate, accompanied by noticeable output ripple, previous modeling results may not provide accurate prediction and design guidelines. In this paper, a new modeling technique taking into account the output capacitor effect is proposed for simple dual-phase switched capacitor converters without complex coupling loops. The proposed model employs transient calculation, takes charge redistribution phase into account, and includes the duty cycle, switching frequency as well as output capacitor simultaneously in the final output impedance formula, which enhances accuracy of the model. It is suitable for interleaved and noninterleaved switched capacitor converters. The simulation and experimental results for the unity gain SC converter are provided to verify the proposed theory. [ABSTRACT FROM PUBLISHER]

Input-series output-series (ISOS) modular dc–dc converters are suitable for applications involving high input and output voltages. Input voltage sharing (IVS) and output voltage sharing (OVS) of the constituent modules must be guaranteed for an ISOS system. A duty cycle-based model predictive control (DC-MPC) scheme is proposed in this paper to achieve IVS and OVS for an ISOS system. The employed switching frequency in the DC-MPC scheme is fixed; duty cycles are optimized and then determined by minimizing a cost function, which is derived from an ISOS system aimed at achieving IVS and OVS. IVS and OVS can, therefore, be obtained by employing the optimized duty cycle within each sampling period. In addition, challenges and disadvantages of directly using traditional MPC to achieve IVS and OVS is briefly discussed, while the proposed DC-MPC can effectively avoid them. Compared with the existing proportional integral-based schemes in the literature, the proposed DC-MPC is better for IVS and OVS because it is a very simple and intuitive approach with lower cost and higher overall dynamic performance. Simulation and experiments are conducted to verify that the proposed DC-MPC scheme works well during both steady and transient states. [ABSTRACT FROM AUTHOR]

DC distribution power systems are vulnerable to instability because of the destabilizing effect of converter-controlled constant power loads (CPLs) and input filters. Standard stability analysis tools based on averaging linearization techniques can be used only when the switching frequency of the converter is significantly higher than the cutoff frequency of the filter. However, dc distribution systems with a reduced size filter, and consequently a high cutoff frequency, are common in transportation applications. Conventional methods fail to detect instabilities in the system because they do not take into account the switching effect. To overcome this drawback, this paper proposes a discrete-time method to analyze the stability of dc distribution systems. This model is applied here to a dc power system with a CPL. The switching effects and the nonlinearities of the system model are taken into account with a simple discretization approach. The proposed method is able to predict the dynamic properties of the system, such as slow-scale and fast-scale instabilities. An active stabilizer is also included in the system model in order to extend the stability margin of the system. Finally, these observations are validated experimentally on a laboratory test bench. [ABSTRACT FROM AUTHOR]

This paper proposes a novel high step-up nonisolated single switch dc–dc converter suitable for regulating dc bus in various microsources especially for photovoltaic (PV) sources. Quadratic boost and switched-capacitor technique are used as primary and secondary circuits, respectively. A coupled inductor is applied to make a connection between them, so a high dc voltage gain is achieved. High efficiency is yield where voltage stress on active switch is alleviated by clamped capacitor; consequently, smaller \rmR\rm{DS(ON)} for power switch is required. On the other hand, input current of the proposed converter is continued, hence stress on the input source is reduced. The operating principles and steady-state analyses are discussed in detail for both continuous and discontinuous conduction modes. Also, the boundary condition is computed. To verify the performance of the proposed converter and theoretical calculations, a 250-W prototype converter is implemented with an input voltage of 24 V and an output voltage of 400 V designed especially for PV sources in continuous conduction mode operation. Finally, simulation results are confirmed by experimental results; maximum efficiency is occurred at 150 W and full-load efficiency is 92.96%. [ABSTRACT FROM AUTHOR]

Variable-speed multiphase (more than three phases) drive systems are seen as serious contenders to the existing three-phase drives due to their distinct advantages. Supply to the multiphase drives is invariably given from a voltage source inverter. However, this paper proposes an alternative solution for supplying multiphase drive system using a direct ac–ac converter called a matrix converter. This paper proposes the pulsewidth modulation (PWM) algorithm for the matrix converter topology with three-phase grid input and five-phase variable-voltage and variable-frequency output. The PWM control technique developed and presented in this paper is based on space vector approach. This paper presents the complete space vector model of the three-to-five-phase matrix converter topology. The space vector model yield 2^15 total switching combinations which reduce to 243 states considering the imposed constraints, out of which 240 are active and 3 are zero vectors. However, for space vector PWM (SVPWM) implementation, only 90 active and 3 zero vectors can be used. The SVPWM algorithm is presented in this paper. The viability of the proposed solution is proved using analytical, simulation, and experimental approaches. [ABSTRACT FROM AUTHOR]

In this paper, a single-phase grid-connected transformerless photovoltaic inverter for residential application is presented. The inverter is derived from a boost cascaded with a buck converter along with a line frequency unfolding circuit. Due to its novel operating modes, high efficiency can be achieved because there is only one switch operating at high frequency at a time, and the converter allows the use of power MOSFET and ultrafast reverse recovery diode. It also features a robust structure because the phase leg does not have a shoot-through issue. This paper begins with theoretical analysis and modeling of this boost-buck converter-based inverter. And the model indicates that small boost inductance will lead to an increase in the resonant pole frequency and a decrease in the peak of Q, which results in easier control and greater stability. Thus, interleaved multiple phases structure is proposed to have small equivalent inductance; meanwhile, the ripple can be decreased, and the inductor size can be reduced as well. A two-phase interleaved inverter is then designed accordingly. Finally, the simulation and experiment results are shown to verify the concept and the tested efficiency under 1-kW power condition is up to 98.5%. [ABSTRACT FROM AUTHOR]

This paper presents a new diagnostic technique for the diagnosis of open-circuit faults in matrix converters operating with an Optimum Alesina-Venturini modulation scheme. Compared to previous diagnostic techniques developed for matrix converters, the technique proposed in this paper has the major advantage of not requiring the installation of any additional sensors in the converter besides the ones already present for control purposes. Hence, it can be easily integrated into the control platform of the converter at no additional cost. In addition to the diagnostic approach, a new fault-tolerant switching strategy is also presented so that after the appearance of an open-circuit fault, the matrix converter can continue to run although with degraded performance, until a repair action can be taken. Several simulation and experimental results are presented, demonstrating the effectiveness and applicability of the developed techniques. [ABSTRACT FROM AUTHOR]

This paper proposes a unified PWM method for matrix converters so as to establish a common platform which can generate various types of PWM methods in real time by adjusting the free parameters in the modulation algorithm. As a foundation for unification, the general form of the modulation functions for matrix converters is derived using geometric transformation approach. All eligible direct modulation matrices are shown to be of indirect form and are expressed in terms of instantaneous phase quantities. This paper also presents a new viewpoint to consider a matrix converter as a generalized three-level inverter and to apply the double-carrier-based dipolar modulation technique of the three-level inverter to the matrix converter. Several concepts of the two-level PWM inverters are then generalized to the matrix converters for better visualization and understanding of the modulation process. [ABSTRACT FROM AUTHOR]

This paper proposes a novel family of cascade three-level (TL) ac–ac direct converters based on ac switch cells, which transfer unsteady high ac voltage with distortion into regulated sinusoidal voltage with low total harmonic distortion (THD). The topological family includes buck TL–boost, buck–boost TL, and buck TL–boost TL modes. In order to achieve a reliable TL ac–ac conversion, a double transient voltage feedback control strategy of the output voltage and the voltage across the flying capacitor is introduced in this paper. A 500-VA 220-V \pm10% 50-Hz ac/220-V 50-Hz ac prototype is presented with the experimental results to prove that the converters have four improved advantages simultaneously, including lower voltage across power switches, bidirectional power flow, low THD of output voltage, and higher input power factor. [ABSTRACT FROM AUTHOR]

Switching power supplies are sources of noise for sensitive circuits. Converters should comply with electromagnetic compatibility (EMC) rules so that the electromagnetic interference (EMI) caused by switching cannot interfere with the normal operation of adjacent circuits and also the converter itself. The produced interference can be in the form of conduction or radiation. In this paper, some techniques are used in switching converters to suppress EMI with emphasis on the conduction form. EMI analysis and evaluation of a conventional flyback converter and a proposed zero-current transition (ZCT) flyback converter is achieved by simulation and experimental results. In addition to evaluating some EMI suppression techniques, the main objective of this paper is to improve EMI in the topology design stage. The operating modes of the improved ZCT flyback are discussed. In addition to the efficiency improvement, the amount of EMI reduction of this ZCT flyback and the effectiveness of some EMI reduction techniques are shown by practical implementation. [ABSTRACT FROM AUTHOR]

A systematic method for deriving soft-switching three-port converters (TPCs), which can interface multiple energy, is proposed in this paper. Novel full-bridge (FB) TPCs featuring single-stage power conversion, reduced conduction loss, and low-voltage stress are derived. Two nonisolated bidirectional power ports and one isolated unidirectional load port are provided by integrating an interleaved bidirectional Buck/Boost converter and a bridgeless Boost rectifier via a high-frequency transformer. The switching bridges on the primary side are shared; hence, the number of active switches is reduced. Primary-side pulse width modulation and secondary-side phase shift control strategy are employed to provide two control freedoms. Voltage and power regulations over two of the three power ports are achieved. Furthermore, the current/voltage ripples on the primary-side power ports are reduced due to the interleaving operation. Zero-voltage switching and zero-current switching are realized for the active switches and diodes, respectively. A typical FB-TPC with voltage-doubler rectifier developed by the proposed method is analyzed in detail. Operation principles, control strategy, and characteristics of the FB-TPC are presented. Experiments have been carried out to demonstrate the feasibility and effectiveness of the proposed topology derivation method. [ABSTRACT FROM AUTHOR]

Interleaving of voltage-source converter (VSC) legs enables higher output currents per phase, effectively increasing the power rating without increasing semiconductor ratings. However, the interleaved operation results in circulating currents between each phase converter legs as well as a zero-sequence circulating current (ZSCC), which become quite prominent when the converters operate with low switching frequencies. This paper demonstrates the interleaved operation of three-level converters under selective harmonic elimination pulsewidth modulation (SHE-PWM). A controller for the circulating current within the legs of each phase is also proposed. The controller is used in combination with optimally selected SHE-PWM patterns to generate the maximum number of voltage levels and minimize the peak value of the circulating current. Simulation and experimental results show the interleaved operation and the effect of SHE-PWM pattern selection in the overall system. [ABSTRACT FROM PUBLISHER]

Efficiency in a light load dc–dc converter is improved by reducing the switching frequency with the load current. Further, a bifrequency operation (BFO) using pulse train (PT) control can achieve spread spectrum. Using discrete-time models, this paper shows that a stable periodic BFO is generally not achievable in existing PT control methods. Thereafter, a unified multimode digital control technique is proposed, in which a voltage-mode digital pulse-width-modulator (DPWM) is used to control a predefined periodic BFO. Beside the fixed-frequency DPWM, an extra multiplexer is considered for real-time configuration to: 1) bifrequency pulse frequency modulation; 2) PT control; or 3) pulse regulation control; or 4) pulse skipping control with smooth transition. Analysis and design methods are discussed to ensure periodic BFO and to customize the power spectrum with predictable ripple parameters. A buck converter prototype is made, and the proposed control is implemented using an FPGA device. [ABSTRACT FROM PUBLISHER]

Dual active bridge converters enable bidirectional power flow in buck and boost operating modes. This paper presents an advanced switching sequence and burst-mode strategy to balance conduction, switching, and magnetic losses under light, medium, and heavy loading conditions, leading to improved operating efficiency. The implementation of the switching sequence employs the natural state-plane trajectories of the converter and contributes to higher efficiency and the ability to perform burst mode. The proposed switching sequences improve the overall efficiency of the converter by enabling soft switching and adjusting the frequency to match the minimum RMS transformer current in the full operating range. Furthermore, it incorporates a fully controlled burst-mode switching sequence for light loading conditions to further extend the efficiency gains. As a result, maximum efficiency is obtained by taking advantage of all the possible switching structures of the converter. The analysis provides insight into the natural trajectories of the converter, which produce soft-switching transitions and enable the converter structures to achieve the target operating point directly. Simulation and experimental results are presented to validate the benefits of the switching sequence and illustrate the burst-mode operation. [ABSTRACT FROM PUBLISHER]

This paper proposes a bidirectional three-level LLC resonant converter with a new pulse width and amplitude modulation control method. With different control signals, it has three different operation modes with different voltage gains. Therefore, it can achieve wide voltage gain range by switching among these three modes, which is attractive for energy storage system applications needing wide voltage variation. The proposed topology operates with constant switching frequency, which is easy to implement with digital control, and it can achieve soft switching for all the switches and diodes in the circuit as a conventional LLC resonant converter. The performance of the proposed converter is validated by the experimental results from a 1-kW prototype with 20 A maximum output current. [ABSTRACT FROM PUBLISHER]

Featuring high efficiency, low harmonic distortion, high modularity and scalability, the modular multilevel converter (MMC) is particularly suitable for high voltage direct current transmission applications. As an advanced control strategy, model predictive control (MPC) has the advantage of direct modeling and fast dynamic response. It can simultaneously control multiple variables through an appropriate cost function. The conventional MPC can achieve an optimal control objective by evaluating all the candidate switching states for the MMC; however, with increasing number of submodules, there is an increasing number of candidate switching states that place an enormous burden on the control. In this paper, a grouping-sorting-optimized MPC (GSOMPC) strategy is proposed for the MMC with the number of submodules for each arm increases to hundreds. It divides all submodules of each arm into M groups, with each containing X submodules. By the implementation of the first level and second level optimized MPC between groups and submodules, respectively, the computational load of each phase decreases from C2N^N to $2X + M + 3(N = M \times X)$. In addition, to reduce the strict requirements of control hardware for sorting and calculation, the proposed strategy is able to simultaneously control the submodule voltage, ac current, circulating current, and switching frequency. Applied to a 2.7-kV/60-kW MMC back-to-back dynamic test system, experimental results verify the feasibility and effectiveness of the proposed GSOMPC strategy. [ABSTRACT FROM PUBLISHER]

In this paper, second-order sliding-mode (SOSM) control approach is applied to synchronous buck dc–dc converters. The proposed SOSM controller can stabilize synchronous buck dc–dc converters using a simple digital state-machine structure, without requiring current sensing or an integral term in the control loop. The SOSM controller results in fast step-load and start-up transient responses, and is robust against parameter uncertainties. Fast transients and current limitation during start up can be accomplished by adjusting one controller parameter. Furthermore, a hysteresis method is introduced to control the switching frequency. The proposed approach is verified by experimental results on a 1.25-V 10-A prototype. [ABSTRACT FROM PUBLISHER]

This paper proposes a simplified space vector modulation (SVM) scheme for multilevel converters. Compared with earlier SVM methods, the proposed scheme simplifies the detection of the nearest three vectors and the generation of switching sequences, and therefore is computationally more efficient. Particularly, for the first time, the proposed scheme achieves the same easy implementation as phase-voltage modulation techniques. Another superior characteristic of the proposed scheme over earlier methods is its potential for multiphase multilevel applications. The proposed scheme also offers the following significant advantages: 1) independence of the level number of the converter; 2) more degrees of freedom, i.e., redundant switching sequences and adjustable duty cycles, to optimize the switching patterns; and 3) no need for lookup tables or coordinate transformations. These advantages make the proposed scheme well suited to large level-number applications, such as modular multilevel converters and high voltage direct current systems. Simulation and experimental results verify this new concept. [ABSTRACT FROM PUBLISHER]

Conventional dual-active bridge topologies provide galvanic isolation and soft-switching over a reasonable operating range without dedicated resonant circuits. However, scaling the two-level dual-active bridge to higher dc voltage levels is impeded by several challenges among which the high dv/dt stress on the coupling transformer insulation. Gating and thermal characteristics of series switch arrays add to the limitations. To avoid the use of standard bulky modular multilevel bridges, this paper analyzes an alternative modulation technique, where staircase approximated trapezoidal voltage waveforms are produced; thus, alleviating developed dv/dt stresses. Modular design is realized by the utilization of half-bridge chopper cells. This way the analyzed dc-dc transformer employs modular multilevel converters operated in a new mode with minimal common-mode arm currents, as well as reduced capacitor size, hence reduced cell footprint. Suitable switching patterns are developed and various design and operation aspects are studied. Soft-switching characteristics will be shown to be comparable to those of the two-level dual-active bridge. Experimental results from a scaled test rig validate the presented concept. [ABSTRACT FROM AUTHOR]

This paper presents the performance analysis and comparison of two types of bidirectional dc–dc converters—cascaded buck–boost capacitor in the middle and cascaded buck–boost inductor in the middle for use in plug-in electric and hybrid electric vehicles. The comparison of the two converters is based on device requirements, rating of switches and components, control strategy, and performance. Each of the converter topologies has some advantages over the other in certain aspects. Efficiency analysis has been carried out for specific scenarios in vehicle applications. The simulation and experimental results are provided for both converter types. [ABSTRACT FROM PUBLISHER]

This paper presents a high step-up converter for fuel cell energy source applications. The proposed high step-up dc-dc converter is devised for boosting the voltage generated from fuel cell to be a 400-V dc-bus voltage. Through the three-winding coupled inductor and voltage doubler circuit, the proposed converter achieve high step-up voltage gain without large duty cycle. The passive lossless clamped technology not only recycles leakage energy to improve efficiency but also alleviates large voltage spike to limit the voltage stress. Finally, the fuel cell as input voltage source 60-90 V integrated into a 2-kW prototype converter was implemented for performance verification. Under output voltage 400-V operation, the highest efficiency is up to 96.81%, and the full-load efficiency is 91.32%. [ABSTRACT FROM AUTHOR]

A systematic method for derivation of a multiport converter (MPC) based on the dc-link inductor (DLI) concept is proposed in this paper. The MPC is generated by interconnecting multiple pulsating voltage cells (PVCs) through the DLIs. The PVCs can be input type, output type, and bidirectional type, and bidirectional MPC topologies can be harvested if all the PVCs are bidirectional type. As a result, a family of novel MPCs, including multiinput converters, multioutput converters, and bidirectional MPCs, are derived. With the proposed MPCs, step-up and step-down voltage conversion between any two of the ports can be implemented. As an example, the three-port bidirectional buck-boost (TP-B 3) converter is analyzed and applied to a stand-alone renewable power system for interconnection of three dc subsystems. The operation principles, pulse width modulation, and feed-back control strategies are presented and analyzed in depth. The analysis indicates that, compared to the traditional common dc-bus-based solution, bulky dc-link capacitor is eliminated and single-stage conversion between any two of the three dc-buses are achieved with the TP-B 3 converter, which is beneficial for higher efficiency, power density, and reliability. Experimental results are given to verify the feasibility and effectiveness of the developed TP-B 3 converter. [ABSTRACT FROM AUTHOR]

The modular multilevel converter (MMC) has been a subject of increasing importance for medium/high-power energy conversion systems. Over the past few years, significant research has been done to address the technical challenges associated with the operation and control of the MMC. In this paper, a general overview of the basics of operation of the MMC along with its control challenges are discussed, and a review of state-of-the-art control strategies and trends is presented. Finally, the applications of the MMC and their challenges are highlighted. [ABSTRACT FROM AUTHOR]

At a certain level of abstraction, power converters can be represented as linear circuits connected to diodes and controlled electronic switches. The evolutions of the electrical variables are determined by the state-dependent switchings, which complicate the mathematical modeling of controlled power converters. Differently from the complementarity models previously presented in the literature, the model proposed in this paper allows to represent as a linear complementarity system also closed-loop power converters, without requiring the a priori knowledge of the converter modes. A model construction procedure, not dependent on the specific converter topology, is presented. The discretization of the continuous-time model allows to formulate mixed linear complementarity problems for the computation of the control-to-output frequency response and the evolutions of both transient and steady-state currents and voltages. As illustrative examples, Z-source, boost, and buck dc-dc power converters under voltage-mode control and current-mode control operating both in continuous and discontinuous conduction modes are considered. [ABSTRACT FROM AUTHOR]

The objective of this paper is to present a methodology for identifying the current flow in the capacitors of a multiphase buck converter by synchronously measuring the capacitor currents. A multiphase buck converter uses multiple parallel buck converters with different switching times to source a large amount of current. Currents in the primary capacitors of a multiphase buck converter are drawn by all phases of the converter; however, the phases switch asynchronously. Synchronizing to the switching of a specific phase reveals how the current from that phase is distributed among the capacitors throughout a circuit board. The proposed measurement method is illustrated by comparing an initial printed circuit board design to a new design to show the effect of better capacitor placement and the addition of a ground plane. The new design confines the phase currents to the capacitors close to the field effect transistors of the specific phase. [ABSTRACT FROM AUTHOR]

This paper presents an asymmetrical cascaded multilevel inverter based on a five-level transistor-clamped H-bridge power cell. A two-cell configuration with a dc link voltage ratio of 4 : 1 is presented. The modulation method is based on the fundamental frequency switching. An analysis of the inverter output voltage and harmonics is presented. Injection of the third harmonic voltage as to maximize the output voltage and the issue of the inverse power flow or regeneration in the low-voltage cell are presented. The prototype of the proposed inverter was built, and its functionality was verified through experimental results. [ABSTRACT FROM AUTHOR]

This paper investigates the different control objectives, such as loss reduction, neutral point (NP) balance and noise reduction of the space vector modulation (SVM), for the three-level neutral point clamped (NPC) converter. A detailed loss model and simulation model is built for quantitative loss and NP voltage ripple analysis. An improved SVM method is proposed to reduce NP imbalance and switching loss/noise simultaneously. The coordinately selected small vectors consider both the NP charge and the pulse sequence so that the minimized NP ripple and switching events are guaranteed in one switching cycle. In addition, the switching events between switching cycles are also considered to reduce the total switching loss. This method ensures an evenly distributed device loss in each phase leg and also a constant system efficiency under different power factors. The control result for NP balance and loss reduction is verified by using both a simulation model and an experimental prototype on a 200-kVA three-level NPC converter hardware. [ABSTRACT FROM AUTHOR]

This paper presents a buck-boost dc-dc converter for LED drivers capable of delivering an output current ranging from 0.1 to 2 A and a variable output voltage ranging between 2 and 5 V, starting from an input voltage spanning from 2.7 to 5.5 V. The dc-dc converter, realized in a 0.18-μm CMOS technology with 5-V option, occupies an area of 4 mm2 including pads. The circuit features automatic mode switching and dynamic sizing of the power transistors to achieve a peak efficiency of 91%. With a switching frequency of 2.5 MHz, the achieved line regulation is lower than 0.1% V-1 and the output voltage ripple is less than 10 mV. The obtained turn-on and load transient settling time are lower than 40 μs, thus allowing pulsed operation of the LEDs, as well as switching among LEDs of different colors. [ABSTRACT FROM AUTHOR]

This paper proposes a novel wide-range soft-switching pulse-width modulation three-level (TL) combined dc-dc converter characterized with no added primary clamping devices and reduced output inductance value. It is well suited for high input voltage dc-dc industrial applications due to following desirable features: all the switches sustain half of the input voltage; off state voltage of the switches is directly clamped by the bulky input capacitors, and no added primary clamping devices such as clamping diodes, flying capacitors, are required; TL waveform before output filter can be achieved, which significantly reduces the value of the output inductance; the modified phase-shift control method can be utilized to achieve wide output range. The converter can obtain zero-voltage switching (ZVS) for all power switches in wide load range; furthermore, less conduction loss is added to achieve ZVS. The operation and theoretical analysis of the proposed converter are presented. Experiments are carried out to validate the proposed converter, and efficiency curves are tested and given. [ABSTRACT FROM AUTHOR]