Search

The planned China fusion engineering test reactor (CFETR) needs one or more negative-ion-based neutral beam injectors (N-NBIs) with a beam energy of 500 or even 1000 keV. In order to prepare for CFETR, a prototype of CFETR N-NBI is being designed. The prototype needs an acceleration grid power supply (AGPS) rated at 200 kV/25 A with a maximum pulselength reaches to 3600 s. The AGPS adopted a single-stage inverter-type high-voltage power supply (HVPS). The output voltage ripple is an important specification of the AGPS, which can affect the efficiency and stability of N-NBI system by influencing the beam divergence. However, the conventional methods cannot be used to limit the output voltage ripple of the inverter-type HVPS used as AGPS of CFETR N-NBI prototype. This paper simplified the AGPS to an insulated three-phase three-level (TPTL) dc–dc converter connected with a dual dc link. The working process of the TPTL dc–dc converter with duty-cycle modulation has been analyzed, and two main continuous conduction modes are described. The influence of key parameters such as duty cycle of inverter, leakage inductance of transformer, and output current on output voltage ripple is analyzed. Based on the analysis results, a so-called combined control strategy was proposed to keep the output voltage ripple at a level. The proposed strategy is suitable for the cases where the object output voltage is below 175 kV. Some simulations were carried out by using MATLAB/Simulink. The results showed that the analysis in this paper is reliable and the proposed control strategy has a good performance. [ABSTRACT FROM AUTHOR]

Enhancement of dc bus voltage utilization for a five-level inverter with single dc source and capacitor-fed H-bridge (CHB) units is investigated in this paper. A carrier-based modulation technique is used for boosting the dc bus utilization, which is established by providing detailed mathematical analysis. The five-level inverter used here is realized by cascading a CHB unit to each phase of a three-level neutral point clamped inverter. The increase in dc bus voltage utilization owes to the pole voltage redundancies offered by CHB units. The floating capacitors of H-bridge units are balanced within a quarter fundamental cycle using the switching state redundancies of pole voltage levels. The aforementioned modulation technique allows the inverter to enhance the dc bus utilization from 0.577 $\text{V}_{\text{dc}}$ to 0.63 $\text{V}_{\text{dc}}$ under unity power factor. This enhancement is obtained in the linear modulation range without increasing the dc bus voltage, and thus, the inverter can operate without the presence of low-order harmonics in its phase voltages. The strength of this paper lies in its detailed mathematical analysis for finding out the limiting modulation index and power factor condition in the light of floating capacitor voltage balancing issue. Simulation as well as experimental verification of the modulation scheme is carried out on an induction motor drive under various operating conditions. It is shown that this carrier-based modulation technique is suitable for any single source inverter topology with one CHB unit per phase. [ABSTRACT FROM AUTHOR]

This paper presents a novel single-stage soft-switched high-frequency-link three-phase dc–ac converter topology. The topology supports unidirectional dc to ac power flow and is targeted for applications like grid integration of photovoltaic sources, fuel cell, etc. The high frequency magnetic isolation results in reduction of system volume, weight, and cost. Sine-wave pulsewidth modulation is implemented in dc-side converter. Though high-frequency switched, dc-side converter is soft switched for most part of the line cycle. The ac-side converter active switches are line frequency switched incurring negligible switching loss. The line frequency switching of ac-side converter facilitates use of high voltage blocking inherently slow semiconductor devices to generate high voltage ac output. In addition, a cascaded multilevel structure is presented in this paper for direct medium-voltage ac grid integration. A detailed circuit analysis considering nonidealities like transformer leakage and switch capacitances, is presented in this paper. A 6-kW three-phase laboratory prototype is built. The presented simulation and experimental results verify the operation of the proposed topologies. [ABSTRACT FROM AUTHOR]

To support the development of high-frequency ac microgrids in terms of compact design, high-voltage gain and low total harmonic distortion (THD), a buck–boost dual-leg-integrated step-up inverter is proposed in this paper. The inverter is formed by integrating a buck–boost converter into a conventional single-phase full-bridge inverter by sharing the upper switch and the body diode of the lower switch in both bridge-legs. Consequently, the component count is significantly reduced over the step-up inverter counterparts. In addition, to address the drawbacks of hybrid modulation methods adopted by existing dual-leg-integrated inverters, such as double-variable control, and high THD of output voltage/current at high input voltage and heavy load conditions, unipolar frequency doubling sinusoidal pulse width modulation scheme is adopted in this inverter. As a result, the modulation ratio M becomes the only control variable to regulate the output voltage/current and the control is simplified. The THD of the proposed inverter output can remain low throughout the entire input voltage range and load power range. This paper presents the topology derivation procedure, operation principle, and steady-state characteristics of the proposed inverter. To validate the effectiveness of theory, experimental results of a 400 W hardware prototype, where the output voltage frequency is at 500 Hz, are reported. [ABSTRACT FROM PUBLISHER]

This paper proposes a current-fed single-phase inverter without constant intermediate DC link. It eliminates electrolytic capacitor from the DC-link and introduces an intermediate pulsating DC bus. The proposed topology is modular with three full-bridges making it scalable for high-power applications. New pulsating-DC-modulation for back-end pulsating DC-link inverter and secondary modulation (SM) for front-end DC-to-pulsating DC converter is proposed. Soft-switching and device voltage clamping of both primary side and secondary side devices of front-end current-fed full-bridge converter is realized. A rotating partial hybrid pulsewidth modulation has been introduced. One leg of inverter is commutated at a low switching frequency, while the other leg is operated at a high switching frequency for partial period of a line frequency cycle. Thus, switching losses of the back-end inverter are considerably reduced. Rotating mechanism is used to equalize the switching losses of four switches of the inverter. This paper presents detailed operation and analysis of the topology with a proposed modulation scheme. Simulation and experimental results validate the effectiveness and accuracy of the proposed modulation scheme as well as soft-switching and performance of the converter. [ABSTRACT FROM PUBLISHER]

This paper investigates and evaluates the performance of a single-phase split-source inverter (SSI), where an alternative unidirectional dc–ac configuration is used. Such configuration is utilized in order to use two common-cathode diodes in a single device instead of using two separate diodes, resulting in minimum parasitic inductance in the commutation paths. In this paper, the analysis and modulation of the single-phase SSI using this alternative configuration is discussed, and the analysis of the low-frequency component in the dc side is introduced. Moreover, the features behind employing the triangular, the trailing-edge sawtooth, and the leading-edge sawtooth carriers with the single-phase SSI are discussed, and the differences among these carriers are highlighted. In order to highlight the performance of the proposed SSI, a comparative study is conducted with the two-stage architecture and the single-phase quasi-Z-source inverter (qZSI). The introduced analysis is enhanced with simulation results using MATLAB/PLECS models, where a 1-kVA single-phase SSI is designed and simulated. Finally, the designed 1-kVA single-phase SSI is implemented experimentally and tested at different operating points, i.e., at different voltage gains, and a maximum efficiency of $95.5\%$ is obtained. [ABSTRACT FROM PUBLISHER]

Finite state model predictive control (MPC) has been recently applied to several converter topologies, as it can provide many advantages over other MPC techniques. The advantages of MPC include fast dynamics, multitarget control capability, and relatively easy implementation on digital control platforms. However, its inherent variable switching frequency and lower steady-state waveform quality with respect to standard control, which includes an appropriate modulation technique, represent a limitation to its applicability. Modulated model predictive control (M2 PC) combines all the advantages of MPC with the fixed switching frequency characteristic of pulse-width modulation algorithms. The work presented in this paper focuses on the indirect matrix converter (IMC), where the tight coupling between rectifier stage and inverter stage has to be taken into account in the M2PC design. This paper proposes an M2PC solution, suitable for IMC, with a switching pattern that emulates the desired waveform quality features of space vector modulation for matrix converters. The switching sequences of the rectifier stage and inverter stage are rearranged in order to always achieve zero-current switching on the rectifier stage, thus simplifying the current commutation strategy. [ABSTRACT FROM AUTHOR]

The conventional three-level inverter only has voltage buck capability. The quasi-Z-source three-level T-type inverter (QZS 3LT $^2$ I) has been proposed to realize voltage buck–boost operation. In this paper, we further propose a novel modulation scheme for the QZS 3LT $^2$ I to realize voltage boosting, reduce the common-mode voltage (CMV), and control the neutral-point voltage balance simultaneously. The proposed scheme adopts a large vector, a medium vector, a small vector with low CMV magnitude, a zero vector, and a shoot-through vector to generate the output voltage. According to sector number and neutral-point voltage difference, a p-type or n-type small vector with low CMV magnitude is properly selected to balance the neutral-point voltage. Shoot-through states are inserted within zero vector to boost the dc input voltage without affecting the ac output voltage. Dwell times of basic vectors are calculated through the revised volt–second balance equation. Furthermore, a coordinate control strategy between neutral-point voltage balance and voltage boosting is proposed. Doing so, the CMV magnitude can be restricted within one-sixth of dc-link voltage and neutral-point voltage imbalance can be effectively mitigated. The effectiveness of the proposed scheme is verified by simulations and experiments. [ABSTRACT FROM AUTHOR]

This paper proposes a new inverter topology based on the active neutral-point-clamped (ANPC) converter with capability to integrate one energy storage system (ESS) per inverter leg with an independent state of charge control, so that each inverter leg has two dc ports and one ac port. The primary dc port is common to all inverter legs and it is connected to the main power source. The secondary dc port is suitable for ESS connection because of its two-quadrant operation, with bidirectional current capability, so that the ESS can be charged and discharged with regulated current. Integration of a secondary dc port with independent control also allows the use of different ESS technologies for each inverter leg to compose a hybrid ESS. Redundant switching states of the proposed structure are used to balance the energy exchanged between the secondary dc port and the dc bus capacitors. Theoretical propositions were experimentally validated through a 1-kW single-phase inverter with a secondary dc port connected to a 230-V ESS and ac port connected to an LC filter feeding a linear load. Low total harmonic distortion (THD) sinusoidal current is generated at the ac port while charging or discharging the ESS with a constant current. [ABSTRACT FROM AUTHOR]

This paper presents the topology and modulation technique of a three-phase three-level modified Z-source neutral-point-clamped (MZS-NPC) inverter, which combines a modified Z-source impedance network and a three-phase three-level NPC inverter. The boost factor of the proposed MZS-NPC inverter is twice as high as the three existing representative topologies combing an impedance network with a three-level NPC inverter. A modulation scheme for the proposed topology, based on a maximum boost control method, is designed to achieve the maximum voltage gain with simple implementation and to balance the dc-link neutral-point voltage. A closed-loop control of the ac load voltage in the fuel-cell or photovoltaic applications based on the proposed inverter is realized, in order to supply a desired voltage to the critical load in islanding mode of a microgrid. The boosting ability and operation validity of the proposed topology and modulation technique are demonstrated with simulation and experimental results. [ABSTRACT FROM AUTHOR]

A pulsewidth-modulation bidirectional ac–dc converter (i.e., active rectifier) with dc-fault-blocking and self-pre-charge capabilities is proposed in this paper for low voltage dc (LVdc) applications. The proposed converter, which is named as “H5 + converter,” consists of an H4 bridge, a bidirectional switch, and a transient-voltage-surge (TVS) diode. The bidirectional switch and the TVS diode enable the dc fault blocking and dc bus self-pre-charge, while preserving the low common-mode voltage noise and low leakage current of the converter. Additionally, the proposed H5+ converter has advanced features under a dc-side short-circuit fault, such as fault diagnosis and fault recovery. Operation principles of the proposed converter are presented and analyzed. A down-scaled prototype is built. Experiment results are shown and analyzed, including steady-state waveforms, common-mode performance, start-up dynamics, as well as dc fault blocking, fault diagnosis, and fault recovery. Moreover, the proposed converter is compared with other two dc-fault-blocking converters for LVdc applications, in terms of converter capabilities, required devices, and power switch losses. [ABSTRACT FROM AUTHOR]

In this paper, an integrated step-up inverter without transformer is investigated for photovoltaic (PV) power generation. The proposed topology can be derived by combining a traditional boost converter with a single-phase full bridge dc–ac converter. The main features of the integrated inverter are: First, the leakage current caused by the solar cell array-to-ground parasitic capacitance can be theoretically reduced to zero due to the characteristics of the converter configuration, which can improve the efficiency and the reliability of the PV generation system; second, the output ac voltage of the proposed inverter can be higher than the input dc voltage, which is capable of connecting low voltage PV panels to the grid; third, only five active switches are used in the presented inverter, and those switching devices can be synchronously driven by various sinusoidal pulsewidth modulation methods based on the carrier; therefore, the proposed inverter is compact and with curtailed cost. The working principle and analysis of the proposed integrated inverter are elaborated. Finally, simulation and experimental results are obtained in a lab prototype, which agree well with the theoretical analysis. [ABSTRACT FROM AUTHOR]

A novel single-stage high-frequency link three-phase ($3\phi$) inverter along with a modulation strategy is presented in this paper. The topology is targeted for grid integration of utility scale renewable and alternative energy sources like solar, fuel cell, and wind, where the power flow is unidirectional (from dc to ac). The primary side converter has a $3\phi$ voltage source inverter (VSI) structure along with an additional half-bridge leg. Sinusoidal pulsewidth modulation is implemented in the primary side converter. The three legs of the primary side VSI are zero voltage switched (ZVS) for most part of the line cycle. The additional half bridge leg is ZVS over the complete line cycle. The active switches in secondary side converter are line frequency switched and thus results in negligible switching loss. The converter switching process is described in detail to show the soft-switching of the primary side converter using the device capacitances and leakage inductances of the high-frequency transformers (HFTs). The HFT galvanic isolation results in high power density. A 4-kW laboratory scale hardware prototype is built and tested with the proposed modulation strategy. The experimental results are presented to verify the converter operation. [ABSTRACT FROM AUTHOR]

Three-level inverter has an outstanding performance and is more advantageous in the switching vector selection than two-level inverter. In particular, the neutral-point voltage unbalance and common-mode voltage (CMV) reduction of three-level inverter should be carefully regulated for the appropriate operation, both of which, however, are mutually coupled resulting that the conventional space vector modulation (SVM) scheme cannot deal with them properly. To overcome this limitation, this paper proposes an improved space vector modulation (ISVM) technique to reduce the CMV and neutral-point voltage imbalance simultaneously. The generating mechanism of neutral-point voltage oscillation is derived. Based on the analysis, the proposed ISVM method adopts four voltage vectors (large, medium, small, and zero vectors) with adjusted dwell times to eliminate the ac unbalance of the neutral-point voltage. Considering the occurrence of neutral-point voltage disturbances, the dc neutral-point unbalance voltage is controlled by selecting the P-type or N-type small vector and adjusting the dwell times of small vectors for neutral-point voltage recovery. In addition, a novel switching sequence arrangement method with the minimal number of switches transition in one switching cycles and between switching cycles is proposed to reduce the total switching loss. Theoretical analysis and verification results show that the proposed ISVM scheme can reduce the magnitude of CMV to half of value using the conventional SVM, and an accurate control of ac and dc unbalanced neutral-point voltage can be obtained. [ABSTRACT FROM AUTHOR]

This paper describes a novel family of single-phase single-stage buck–boost inverters using output unfolding circuits. Operation principles and component design guidelines along with modulation techniques are presented and discussed. The simulation results confirm all theoretical statements. Experimental setup of the most promising solution is assembled and tested, where the efficiency for different operation modes is analyzed. Finally, the pros and cons along with applications of the proposed solutions are discussed in the conclusions. [ABSTRACT FROM AUTHOR]

In this paper, a new space vector pulse width modulation method to extend the linear modulation range of a cascaded five level inverter topology with a single dc supply is presented. Using this method, the inverter can be controlled linearly and the peak phase fundamental output voltage of the inverter can be increased from 0.577 to 0.637 V\text{dc} without increasing the dc bus voltage and without exceeding the induction motor voltage rating. This new technique makes use of cascaded inverter pole voltage redundancy and property of the space vector structure for its operation. Using this, the induction motor drive can be operated till the full speed range (0–50 Hz) with the elimination of lower order harmonics in the phase voltage and phase current. The five-level topology presented in this paper is realized by cascading a two-level inverter and two full bridge modules with floating capacitors. The inverter topology and its operation for extending the modulation range is analyzed extensively. Simulation and experimental results for both steady-state and dynamic operating conditions are presented in this paper. [ABSTRACT FROM AUTHOR]

Increasing demands for power supplies have contributed to the population of high-frequency ac (HFAC) power distribution system (PDS), and in order to increase the power capacity, multilevel inverters (MLIs) frequently serving as the high-frequency (HF) source-stage have obtained a prominent development. Existing MLIs commonly use more than one voltage source or a great number of power devices to enlarge the level numbers, and HF modulation (HFM) methods are usually adopted to decrease the total harmonic distortion (THD). All of these have increased the complexity and decreased the efficiency for the conversion from dc to HF ac. In this paper, a nine-level inverter employing only one input source and fewer components is proposed for HFAC PDS. It makes full use of the conversion of series and parallel connections of one voltage source and two capacitors to realize nine output levels, thus lower THD can be obtained without HFM methods. The voltage stress on power devices is relatively relieved, which has broadened its range of applications as well. Moreover, the proposed nine-level inverter is equipped with the inherent self-voltage balancing ability, thus the modulation algorithm gets simplified. The circuit structure, modulation method, capacitor calculation, loss analysis, and performance comparisons are presented in this paper, and all the superior performances of the proposed nine-level inverter are verified by simulation and experimental prototypes with rated output power of 200 W. The accordance of theoretical analysis, simulation, and experimental results confirms the feasibility of proposed nine-level inverter. [ABSTRACT FROM AUTHOR]

This paper presents a method for generating a multilevel dodecagonal voltage space vector structure using a single dc source for induction motor drives. Multilevel dodecagonal structure combines the advantages of both multilevel and dodecagonal structures, and hence, generates low dv/dt phase voltage along with the elimination of fifth- and seventh-order harmonics over the entire modulation range. This eliminates low-order harmonic currents and prevents the generation of sixth-order torque ripple in the motor. The topology used requires only one dc source making four-quadrant operation of the drive system simpler compared to previously proposed multilevel topologies generating dodecagonal space vector structures. The topology used consists of a three-level flying capacitor (FC) inverter cascaded with a capacitor fed H-bridge. The FC inverter operates at a lower switching frequency and the low-order harmonics are eliminated by the switching action of the cascaded H-bridge inverter. The capacitors in the cascaded H-bridge modules are maintained at a substantially smaller voltage compared to the dc-link voltage and are inherently balanced during the pulsewidth modulation operation. This results in low switching loss, in the FC inverter as well as in the cascaded H-bridge inverter. Experimental results are included to validate the operation of the topology and modulation scheme presented in this paper. [ABSTRACT FROM AUTHOR]

This paper proposes a new fault-tolerant strategy for a multilevel converter with an integrated impedance-source network. The proposed fault-tolerant strategy leverages the flexibility provided by the impedance-source network to implement the fundamental phase-shift compensation (FPSC) method in order to restore operation of a multilevel converter with one or more faulty switches to the prefault conditions. In case of a fault occurrence, the proposed fault-tolerant strategy makes the most use of the remaining converter capacity and generates balanced line-to-line voltages, while evenly distributing an inevitable voltage stress increase, over all converter switches. In this paper, first, a brief background about an impedance-source based cascaded H-bridge converter and a suitable modulation method for it is provided. Then, the FPSC method is explained and the proposed fault-tolerant strategy based on this method is introduced. Finally, several experimental results from a prototype converter are provided to validate the operation of the proposed strategy. [ABSTRACT FROM PUBLISHER]

This paper proposes a new topological configuration for a unified power quality conditioner (UPQC). Generally, the power structure of the three-phase three-wire UPQC consists of two back-to-back connected six-switch inverters. For this configuration, out of 12 switches, six of the series inverter switches will be underutilized most of the time. To improve the semiconductor utilization and consequently to reduce the total switch count, this paper proposes a new reduced switch topology for the UPQC. The proposed topology is realized using only ten switches and retains all the performance merits of the 12-switch UPQC while minimizing its underutilization without increasing the switch VA rating. The paper provides a detailed analytical study and evaluation by comparing the proposed topology with the twelve- and nine-switch-based UPQC system configurations. The feasibility of the proposed topology is validated through experimental investigation. [ABSTRACT FROM AUTHOR]

This paper proposes a new fault-tolerant strategy for the purpose of revamping the performance of three-phase multilevel (ML) converters with faulty switches. The proposed fault-tolerant strategy is based on an adaptation of the modified space vector modulation (SVM) technique to the fundamental phase-shift compensation method. The proposed fault-tolerant strategy generates balanced line-to-line voltages with increased voltage levels in the faulty condition. In this paper, first a brief background about cascaded H-bridge (CHB) ML converters and SVM technique is provided. Then the proposed fault-tolerant strategy and the modified SVM technique are presented. Finally, several experimental results are provided to validate operation of the proposed strategy. [ABSTRACT FROM AUTHOR]

Aimed at the problem that the auxiliary commutation circuit (ACC) of auxiliary resonant commutated pole (ARCP) inverters has a high loss in commutation processes, this paper presents a novel modulation strategy with shunt dead time based on a double ARCP (DARCP) inverter. In comparison with the original modulation strategy, this modulation strategy cannot only achieve soft switching for all switches, but also avoid the superposition of resonance current and load current at commutation moments in double ACCs (DACCs) and make the maximum current through DACCs approximately equal to load current in commutation processes. So, the circulating current loss in DACCs and the current stress of auxiliary switches can be effectively reduced. According to the equivalent circuits in different operation modes under the novel modulation strategy, this paper analyzes the operation principle, soft-switching implementation condition, and optimal parameter design procedure of the DARCP inverter. Finally, a 10-kW–16-kHz DARCP inverter prototype with insulated gate bipolar transistor-based switches is built. Experimental results are given to demonstrate the validity and features of the DARCP inverter under the novel modulation strategy. [ABSTRACT FROM AUTHOR]

Paralleled inverters have the merits of high power rating, improved reliability, and convenient maintenance. However, zero-sequence circulating current (ZSCC) will occur and lead to current distortion and system loss. The ZSCC control is more complicated when three-level topology is utilized and paralleled number is increased. Therefore, this paper proposes a simplified ZSCC suppression scheme for multi-paralleled three-level T-type inverters (3LT2Is). A novel equivalent model is developed and the ZSCC controller based on the new model is easier to implement. Thus, the number of paralleled inverters can be increased without complicating the control scheme and the inverters could be switched on or off optionally. Besides, Feed-Forward (FF) strategy is adopted to eliminate the ZSCC spikes caused by symmetrical three-level space vector modulation. The effectiveness of the proposed control scheme is verified by both simulation and experimental results. [ABSTRACT FROM AUTHOR]

A variable switching frequency space vector modulation control method is proposed in this paper. It is used to achieve zero-voltage switching (ZVS) for two parallel 180° interleaved three-phase grid-connected voltage-source inverters at unity power factor. A wide range of ZVS can be achieved without any additional sensor, auxiliary circuit, or current zero-crossing detection circuit. The carrier wave frequency is easy to be calculated and updated with digital control. The current ripple is precisely predicted and controlled to minimize unnecessary circulation loss. The high current ripple at the inverter side can be considerably canceled by the parallel interleaved configuration. LCL filter is used to further attenuate the current ripple and improve the power quality at the grid side. The switching loss can be significantly reduced especially by using a wide bandgap device with low turn-off loss. The power density is greatly improved owing to the high switching frequency and low component parameters of the filter. A 4.5-kW simulation and experimental prototype interfacing 400 V dc with a three-phase 110-V ac grid is developed to verify the performance of the proposed control strategy. [ABSTRACT FROM AUTHOR]

Leakage current reduction is one of the important issues for transformerless photovoltaic (PV) systems. Many interesting solutions have been reported to reduce the leakage current for three-phase PV inverters. However, most of them are limited to two-level inverters. Moreover, there is a potential risk of the overcurrent phenomenon. In order to solve the problem, a Z-source three-level four-leg inverter with a new modulation strategy is proposed in this paper. First, the mathematical modeling of the three-level four-leg Z-source inverter for leakage current reduction is established for the first time. Second, a new carrier-based modulation strategy is proposed by utilizing the effective large, medium, small, and zero vectors, instead of the invalid vectors, to achieve the constant common-mode voltage, as well as the leakage current suppression. Finally, the proposed solution is carried out on the Texas Instruments TMS320F28335 DSP + Xilinx XC3400 field-programmable gate array digital control hardware platform. The experimental results verify the effectiveness of the proposed solution. [ABSTRACT FROM AUTHOR]

This paper explores the issue of the neutral-point oscillation in the four-leg neutral-point clamped inverter. Such an issue is closely associated with the neutral-point current, so this study models the inverter on the dc side to clarify its relationship and presents a three-dimension pulsewidth modulation to eliminate the neutral-point oscillation. In addition, an offset-injection approach to reducing the neutral-point oscillation is also investigated and discussed. The laboratory test results will validate the analysis of the proposed approach, and a discussion will be presented to evaluate the effectiveness of eliminating the neutral-point oscillation. [ABSTRACT FROM AUTHOR]

SiC mosfets allow a higher frequency, lighter weight inverter over their Si counterparts for electric vehicle (EV) applications. However, using SiC-based EV traction inverters is likely to increase the shaft voltage in an ac motor drive system, which significantly affects the reliability of the system. This paper investigates the impact of high-speed switching of SiC devices and high switching frequency of SiC-based inverter on the common-mode voltage (CMV) and the shaft voltage. It is theoretically illustrated and experimentally demonstrated that the high switching frequency increases the amplitude of the shaft voltage, while the fast switching speed has limited influence on both CMV and the shaft voltage. Afterward, active zero state pulsewidth modulation (AZSPWM) and common-mode chokes are employed to mitigate the shaft voltage. The experimental results show that either the AZSPWM modulation scheme or common-mode chokes have the capability to minimize the shaft voltage. Better performance can be achieved by utilizing both techniques simultaneously. It is also observed that the high switching frequency enabled by the fast-speed SiC device is able to be helpful to the use of reduced shaft voltage technologies. [ABSTRACT FROM AUTHOR]

The leakage current originated from the fluctuations of the common-mode voltage (CMV) is an issue in a transformerless grid-connected photovoltaic system. In this paper, a modified space vector modulation based on the Fourier transform analysis is proposed to reduce the leakage current in a three-phase quasi-Z-source inverter (qZSI). The CMV harmonic content in a qZSI contains low- and high-frequency harmonics that cause safety and electromagnetic interference problems, respectively. By implementing the proposed modulation in a three-phase qZSI, the low-frequency harmonics of the CMV are mainly reduced. The distribution of the high-frequency harmonics is also modified in a way they can be simply filtered. Passive filtering in a qZSI using other modulation techniques is less effective than using this method. Applying the proposed modulation in the presence of a high-frequency inductive-capacitive filter results in the strong suppression of both high- and low-frequency harmonics (more than 90% in the investigated case). A reduced-voltage prototype is designed to evaluate the modulation method. The experimental results from this prototype verify the accuracy of the proposed technique. [ABSTRACT FROM AUTHOR]

This paper proposes a switching strategy for the Z-source inverter (ZSI), which has unequal short-through intervals to reduce the current ripple in the inductor of its impedance source. A size reduction of the inductor of the ZSI is one of the important issues in improving the power density of the ZSI, and the inductor current ripple reduction is required to achieve it. The proposed method can reduce the inductor current ripple by 27.8% compared with the conventional method that has equal short-through intervals without increasing the number of inverter switching. The proposed operation and ripple reduction were confirmed in experiments with a 3-kW-class laboratory prototype. Its result agreed to the calculated results, and it was confirmed that there is no increase in circuit losses caused by the application of the proposed method. [ABSTRACT FROM AUTHOR]

In this paper, a new zero-sequence current suppression control strategy for the five-phase open-winding fault-tolerant fractional-slot concentrated-winding interior-permanent-magnet (FTFSCW-IPM) motor drive system with a common dc bus is proposed. By unequal distribution of the zero voltage vector, the proposed method can well suppress the zero-sequence current caused by the dead-time effect that the conventional eliminating method cannot be achieved. First, the dead-time effect to the zero-sequence current is discussed. Then the zero-axis controller is designed to obtain the reference common-mode voltage. Last, according to the principle of the unequal zero voltage vector distribution, the switching sequence of the two inverters can be calculated, and the maximum modulation index is also first deduced in detail. The proposed method is proved by the simulation and experimental results. [ABSTRACT FROM AUTHOR]

Due to the lack of electrical isolation, the leakage current is one of the most important issues for transformerless photovoltaic (PV) systems. In this paper, a new modulation strategy is proposed to reduce the leakage current for a Z-source four-leg transformerless PV inverter. First, the common-mode loop model is presented. And then the common mode voltage behavior and the effect of factors on the leakage current are discussed. A new modulation strategy is proposed to achieve the step-up function and constant common mode voltage. Therefore, the leakage current can be suppressed effectively. Finally, the proposed strategy is digitally implemented and tested on the TMS320F28335 DSP and XC3S400 FPGA controlled hardware platform. The experimental results verify the effectiveness of the proposed solution. [ABSTRACT FROM AUTHOR]

This paper presents new space vector pulsewidth modulation (PWM) strategies for a single-phase three-level buck-boost neutral point clamped inverter coupled with impedance-source (IS) network. These strategies can be implemented for systems with any IS network with neutral point. The case study system is based on the quasi-Z-source inverter with continuous input current. To demonstrate an improved performance, the strategies are compared with a traditional PWM strategy. The advantages lie in reduced switching number, without output voltage quality distortion. The simulation and experimental results confirm the theoretical predictions. [ABSTRACT FROM AUTHOR]

In this paper, a novel critical-conduction-mode-based modulation is proposed for three-phase bidirectional ac–dc converters. With this modulation, the switching frequency variation range shrinks, zero-voltage-switch soft switching is achieved, and the switching-related loss is reduced, which is especially beneficial for systems operating above hundreds of kHz high switching frequency with wide-band-gap power semiconductor devices to achieve both high power density and high efficiency. A 25 kW silicon carbide based high-frequency three-phase bidirectional ac–dc converter prototype is designed to achieve a power density of 127  ${\text{W/in}}^{3}$ , which is at least five times higher than commercial products. All the control functions are digitally implemented with one low-cost microcontroller, and the aforementioned benefits are experimentally verified on this prototype under both inverter mode and rectifier mode operations. With the proposed soft-switching modulation, the tested peak efficiency is close to 99.0% for this prototype even at above 300 kHz high switching frequency operation. [ABSTRACT FROM AUTHOR]

An isolated single sourced multi-output dc/dc converter with a high-frequency link was proposed before to feed different cells of the Asymmetrical Cascaded H-bridge (ACHB) inverter. One of the fundamental advantages of the ACHB is that the main H-bridge is commutated with fundamental frequency, passing the majority of the inverter power. However, the isolated dc/dc converter needs to be connected to the main voltage source with high-voltage/high-frequency switches, which limits the power capability and the efficiency of the converter. In this paper, a switching pattern based on nearest level modulation method is proposed to command all the power to be transferred through the main H-bridge. Therefore, the power circulates between the auxiliary H-bridges with no need for high-voltage switches. As a result, a single-input single-output auxiliary converter is needed with only 5% of the power rating. This solution reduces cost and size while it improves the efficiency of the converter. Furthermore, the architecture makes the inverter more suitable for high power and high-voltage applications. The inverter switching strategy is based on programmable firing angles. The main dc-link of the grid connected inverter is controlled to achieve maximum power point tracking, while the dc/dc isolated converter is controlled to regulate the auxiliary dc-links. The proposed topology is verified by simulation and experimental results using a 1.5 kW hardware prototype. [ABSTRACT FROM AUTHOR]

Conventional two-level as well as multilevel voltage-source-inverter topologies with a hexagonal voltage-space vector structure generate low-order harmonics in the machine terminal voltages when operated beyond the linear modulation range in variable speed drive application. Progressing from hexagonal to a higher sided polygonal voltage-space-vector structure (VSVS) suppresses significant low-order harmonics throughout the modulation range. In addition, the linear modulation range will also be enhanced very near to the base speed. In this paper, for the first time, the generation of a multilevel 24-sided VSVS using a single dc source for induction-motor drives is proposed. A cascaded topology with a dc-source-fed flying-capacitor inverter and two low-voltage capacitor-fed H-bridge cells forms the power circuit. The features and advantages of the proposed scheme are validated through experimental results and discussions. [ABSTRACT FROM AUTHOR]

This paper proposes advanced speed control for a five-leg voltage source inverter (FLVSI) that drives the dual three-phase induction motor system used in industrial manufacturing processes. The advanced speed control method consists of two controllers: 1) The first is a slip controller that satisfies the application requirement, i.e., to control the mechanical speed of two motors equally regardless of the load condition. 2) The second is an angle controller that satisfies the FLVSI requirement, i.e., to control the phase angle difference between the two motors for minimizing the common leg current because the common leg current can be twice higher than other leg's current depending on the operation condition of the dual motor. Stability analysis of the two controllers under advanced speed control is implemented, and the whole performance of the advanced speed control for the FLVSI-fed dual-motor drive system is shown to identify its feasibility through the experimental results. [ABSTRACT FROM AUTHOR]

Common-mode voltage (CMV) is known as a major cause of premature motor failures. The form and amplitude of the CMV generated by any converter depends on both the circuit topology and modulation technique. Among single stage ac–ac converters employed in drive applications, the Z-source ultra sparse matrix converter (ZSUSMC) is a desirable choice due to reduced number of switches in its structure and voltage boosting capability. Based on these considerations, this paper aims to: 1) theoretically determine and compare the CMV of the ZSUSMC with four well-known impedance networks, namely, cascaded, switched-inductor, quasi, and series, in its structure and 2) propose modulation techniques for CMV reduction in the ZSUSMCs. To this end, first, it is shown that the ZSUSMC, depending on the impedance network used in its structure, provides more freedom to choose from redundant switching states compared to the ultra sparse matrix converter. Then, by taking advantage of this feature, novel modulation strategies that attenuate the CMV without affecting the boosting capability are developed. The proposed modulation schemes are based on avoiding the switching states most contributing to the CMV during a switching period. Through hardware-in-the-loop studies, the effectiveness of the proposed modulation strategies in reducing the CMV of the ZSUSMCs is verified. [ABSTRACT FROM AUTHOR]

In this paper, a modified selective harmonic mitigation pulse amplitude modulation (SHM-PAM) is presented to be capable of canceling all triplen harmonic orders and suitable for single-phase application of five-level type of voltage source inverters. To this end, a new constraint is established for the two switching angles (α1, α2) to derive the new formula for the harmonics’ amplitude, which results in self-elimination of all triplen harmonics (e.g., 3rd, 9th, 15th, …). The fifth and seventh harmonic orders are mitigated through normal operation of the proposed SHM-PAM technique. It is also shown that the proposed technique is extendable to other multilevel voltage waveforms and a flowchart of self-elimination of all triplen harmonics has been presented. Mathematical analysis supported by experimental investigations show the desired performance of the proposed SHM-PAM algorithm on a two-cell single-phase cascaded H-bridge inverter as a typical five-level configuration in dealing with linear and nonlinear loads. Then, it is demonstrated that the maximum number of harmonic orders would be controlled with the minimum number of available angles in a low switching frequency voltage waveform. [ABSTRACT FROM AUTHOR]

In this paper, a novel space vector modulation (SVM) strategy is proposed and designed for dual three-phase three-level motor drives based on vector space decomposition (VSD), which could be applied for high-power and high-reliability applications. The key of the proposed method is to design two decoupled groups of voltage vector candidates for synthesis on α − β subspace and x − y subspace, respectively. The two decoupled groups of voltage vectors will synthesize respective voltage references on α − β subspace and x − y subspace, while having no impact on each other. The redundant small voltage vectors and zero-sequence voltage vectors are utilized to mitigate voltage oscillation in midpoint of dc link and suppress zero-sequence current component for dual three-phase windings with a common neutral. For comparison, another VSD-SVM strategy is designed based on traditional solution, which cannot offer closed-loop control on x − y subspace. Both simulation and experiments have been given to verify that the proposed decoupled VSD-SVM can suppress harmonic components on x − y subspace besides tracking torque components on α − β subspace. Furthermore, the harmonic performance of the proposed decoupled VSD-SVM has been compared with the traditional VSD-SVM strategy and the carrier disposition based pulsewidth modulation. [ABSTRACT FROM AUTHOR]

Although high-frequency circulating current exists in parallel-operated inverters, it has not attracted as much attention as low-frequency circulating current, and thus has not been analyzed in detail previously. In this paper, a mathematical model and analysis are presented, which reveal the spectrum components and their changing trends of the circulating currents caused by carrier phase differences. The impact of carrier phase difference on high-frequency circulating current is also analyzed and verified. A closed-loop control scheme is proposed to suppress the switching frequency circulating current caused by carrier phase difference. In addition, the deadbeat and closed-loop control are combined to suppress the low- and high-frequency circulating currents simultaneously, to improve the overall performance of circulating current suppression. The effectiveness of the proposed scheme is verified by the simulation and experimental results acquired from a laboratory platform. [ABSTRACT FROM AUTHOR]

This paper proposes a control method for a five-level hybrid flying-capacitor (5L-HFC) inverter, of which structure stems from the conventional five-level active neutral-point-clamped (5L-ANPC) topology by dividing the dc-link stage into three series-connected capacitors. In this inverter, the voltage stress on the power switches connected to the dc link is reduced by a half compared with that of the 5L-ANPC topology, thus the lower number of equally voltage-rated power devices can be employed. Also, the power losses in the 5L-HFC inverter are more evenly distributed than in the 5L-ANPC. In order to balance the dc-link capacitor voltages, a third-order harmonic offset injection is applied. When a diode rectifier is used to supply the dc bus voltage, the balancing method is not effective if the modulation index is higher than 0.64. Thus, an auxiliary circuit is needed to support the balancing of the dc-link capacitor voltages. However, the unbalancing problem can be overcome in a full-range operation without the auxiliary circuit if the back-to-back configuration is utilized. Finally, simulation and experiment results have verified the performance of the 5L-HFC inverter with the proposed control method. [ABSTRACT FROM AUTHOR]

The current source converter (CSC) has been popular in high-power medium-voltage applications. To increase the system power capacity and reduce the output harmonics, parallel connection of CSCs with multilevel current output is a practical approach. There are mainly two types of parallel based configurations. The structure with an independent dc link for each paralleled CSC can be regarded as the first configuration, where the dc current flowing into each CSC can be controlled from the rectifier side independently. The second type is constructed with only one current source rectifier (CSR) on the grid side and paralleled current source inverters (CSIs) on the load side, which could potentially reduce the cost and size of the system. However, with a common dc source, the dc current for each CSC should be carefully controlled with proper modulation design. At the same time, the common-mode voltage (CMV), which increases the motor line-to-ground voltage and causes additional stress to the insulation system, should also be suppressed. In this paper, with a focus on the shared dc-link structure, we thoroughly analyze the dc-link current flow and common-mode loop circuit. We propose a multilevel modulation strategy of the parallel CSI system considering the requirement of dc current balancing and CMV reduction to improve the overall system performance. The effectiveness of the proposed method is verified by both simulation and experiment in a transformerless parallel CSC system. [ABSTRACT FROM AUTHOR]

This paper investigates the open-circuit faults of switching devices in the three-level T-Type inverter and proposes a new tolerant control method. The three-phase current and variation of the neutral-point voltage are detected to determine the fault switch. A carrier-based pulse width modulation is developed to tolerate switch fault by transiting from three-level to two-level switching. This makes the modulation scheme easier to be implemented compared to space vector modulation. For the neutral-point fault, the fault phase is operated by two-level modulation to produce the same rating voltage. On the other hand, the inverter is able to produce balanced voltage with reduced rating by keeping the phase of half-bridge fault to the neutral-point voltage. The neutral-point voltage is also able to be balanced by using two-level modulation since it does not contribute the neutral-point current. The performance and effectiveness of the proposed tolerant control are verified by a laboratory build. [ABSTRACT FROM AUTHOR]

Owing to low cost, small size, and low weight, transformerless inverters became prominent in single-phase grid connected photovoltaic (PV) systems. Key issues pertaining to these inverters include suppression of common mode (CM) leakage current and improvement of conversion efficiency. Achieving higher efficiency in single-phase grid-connected photovoltaic systems depends on the number of stages involved in feeding power to the grid, predominantly, if the PV array voltage is less than the peak value of the grid voltage. In this paper, an integrated dc–dc converter based grid-connected transformerless PV inverter is proposed which is aimed at maintaining high efficiency, even if the PV array voltage falls below the peak value of grid voltage (efficient operation at an extended input voltage range). A modulation strategy is discussed in order to minimize the flow of CM leakage current. Further, the efficiencies of certain transformerless inverter topologies are analyzed and compared with that of the proposed topology. Detailed simulation studies are carried out in MATLAB/Simulink environment to verify the analysis. Experimental results for a scaled down laboratory prototype are included as a proof-of-concept to validate the claims. [ABSTRACT FROM AUTHOR]

In order to prevent the power switching devices (e.g., an insulated-gate bipolar transistor, IGBT) from shoot-through in voltage-source converters during a switching period, the dead time is added either in the hardware driver circuits of the IGBTs or implemented in software in pulse width modulation (PWM) schemes. Both solutions will contribute to a degradation of the injected current quality. As a consequence, the harmonics induced by the dead time (referred to as “dead-time harmonics” hereafter) have to be compensated in order to achieve a satisfactory current quality, as required by standards. In this paper, the emission mechanism of dead-time harmonics in single-phase PWM inverters is, thus, presented considering the modulation schemes in detail. More importantly, a repetitive controller has been adopted to eliminate the dead-time effect in single-phase grid-connected PWM converters. The repetitive controller has been plugged into a proportional-resonant-based fundamental-frequency current controller so as to mitigate the dead-time harmonics and also to maintain the control of the fundamental-frequency grid current in terms of dynamics. Simulations and experiments are provided, which confirm that the repetitive controller can effectively compensate the dead-time harmonics and other low-order distortions, and also, it is a simple method without hardware modifications. [ABSTRACT FROM AUTHOR]

In this paper, angular modulation index (AMI) implemented through a modified space vector modulation for the dual voltage source inverters (VSI) is proposed with the primarily aiming to reduce switching losses. The desired voltage across the load is synthesized by applying appropriate phase-angle displacement between space vector references. The proposed approach avoids the use of a dc/dc boost converter (which imposes loss and weight/price penalty to duplicate the dc-link voltage) and results to be particularly suitable for electrical/hybrid vehicle applications. Namely, the application of saving energy to keep driving has been identified as major concern. Hence, this work focuses on the strategy to enhance efficiency. The principles of the proposed controlling method and switching loss, which is reduced at least by 50%, are theoretically evaluated. This paper proposes a pioneering mathematical approach to correctly determine total harmonic distortion (THD) value of the voltage/current for the dual-VSI structure. Furthermore, simulation and experimental results prove that the proposed method insures benefits in terms of common-mode voltage, THD of the voltage, and switching loss reduction. The dual-VSI prototype supplying 1.5-kW induction motor is assembled in the laboratory to experimentally evaluate performance of the proposed method. Also, the simulation results carried out through MATLAB/Simulink environment are given to confirm performance of this easy-to-implement and high-efficient method. [ABSTRACT FROM PUBLISHER]

This paper presents a new application of power and voltage balance control schemes for the cascaded H-bridge multilevel inverter (CHMI)-based solid-state transformer (SST) topology. To reduce load on the controller and simplify modulation algorithm, a master–slave control (MSC) strategy is designed for the dual active bridge (DAB) stage. The master controller executes all control and modulation calculations, and the slave controllers manage only device switching and protection. Due to the inherent power and dc-link voltage unbalance in cascaded H-bridge-based SST, this paper presents a compensation strategy based on three-phase dq decoupled current controller. An optimum zero-sequence component is injected in the modulation scheme so that the three-phase grid currents are balanced. Furthermore, to tightly regulate the output voltage of all the DAB modules to target value, a dynamic reference voltage method is also implemented. With this proposed control method, the three-phase grid currents and dc-link voltage in each module can be simultaneously balanced. Finally, simulation and experimental results are presented to validate the performance of the controller and its application to microgrid SST. [ABSTRACT FROM PUBLISHER]

This paper proposes a new fault-tolerant strategy to revamp performance of three-phase multilevel converters with a single faulty switch. The proposed fault-tolerant strategy is based on the application of a modified selective harmonic elimination (SHE) technique in conjunction with the fundamental phase-shift compensation method. The proposed fault-tolerant strategy makes the most use of the converter capacity in the faulty condition, generates balanced line voltages, and eliminates a wide range of lower order harmonics to limit the total harmonic distribution of the converter voltages in the faulty condition. In this paper, first, a brief background about cascaded H-bridge multilevel converters and SHE technique is provided. Then, the proposed fault-tolerant strategy and the modified SHE technique are presented. Finally, several experimental results are provided to validate the operation of the proposed strategy. [ABSTRACT FROM PUBLISHER]

A virtual space vector modulation technique reducing both magnitude and third-order harmonic component of the common-mode voltage (CMV) in a two-level voltage-source inverter (VSI) is proposed in this paper. The presented method employs a set of virtual space vectors constructed from original stationary space vectors to conduct modulation. Since the created virtual vectors have the lowest instantaneous and zero average CMVs, both the magnitude and third-order harmonic component of the generated CMV are reduced, contributing to better overall CMV performance and common-mode filter design in VSI applications. Three variants of the proposed modulation method using different virtual space vector combinations are presented. The concept of the virtual space vector modulation technique demonstrated with two-level inverter in this paper can also be extended to multilevel inverters. Simulation and experimental results, as well as comparisons with existing methods are provided to verify the proposed technique. [ABSTRACT FROM AUTHOR]

In order to solve the neutral-point voltage unbalancing problem for three-level inverters, this paper proposes a method to balance the neutral-point voltage for three-level inverters with variable modulation wave offset sinusoidal pulse-width modulation (SPWM) control. Based on the mathematical expressions of neutral-point voltage unbalancing, the factors are studied, which affect the fluctuation of neutral-point voltage. Theoretically the mathematical expressions of the neutral-point voltage with the proposed method are derived, and the mathematical relationship between the fluctuation of neutral-point voltage and the adjusting offset of modulation wave is studied. This proposed method realizes controlling the neutral-point voltage balance by dynamically calculating the offset superimposed to the modulation wave based on SPWM (DCOSPWM). This DCOSPWM method is very simple, which has good steady-state performance and is easy for digital implementation. The simulation results verify the correctness of the theoretical analysis in this paper, and the feasibility and effectiveness of this method is verified by the experiments in the experimental platform of neutral point clamped three-level inverters based on digital signal processor (DSP)-complex programmable logic device (CPLD). [ABSTRACT FROM AUTHOR]