Search

Abstract: Delamination-free ultrafiltration (UF) dual layer hollow fibers have been successfully fabricated by dry jet-wet spinning technique. Two different polymers of poly(amide-imide) (PAI) and polyethersulfone (PES) were utilized as the selective layer on the outer side and the porous support layer on the inner side, respectively. The dual layer substrates were subsequently modified to develop a nanofiltration (NF)-like skin on the outer layer by polyethyleneimine (PEI) cross-linking followed by multilayer polyelectrolyte depositions. These membranes were characterized by a series of standard protocols in terms of membrane structure, permeability and salt rejection, and were applied in FO process. Experiments reveal that the dual-layer NF hollow fiber modified by polyelectrolyte cross-linking and depositions can achieve pure water permeability of 4.1l/m2.h.bar and a high rejection to MgCl2 up to 97%. In FO process, the dual-layer hollow fibers exhibited a water flux of 39 and 21lm−2 h−1 in the orientations of active layer facing draw solution and feed water, respectively, by using 0.5M MgCl2 as draw solution and de-ionized (DI) water as feed at room temperature. It suggests that the combined treatment of polyelectrolyte cross-linking and deposition is an effective way to form a NF-like selective layer for FO dual-layer hollow fiber membranes. [Copyright &y& Elsevier]

Abstract: A novel dual-layer forward osmosis (FO) hollow fiber membrane has been designed and successfully fabricated by using a triple orifice spinneret. The fiber consists of two layers made from polyamide-imide (PAI) polymer for the outer layer and polyethersulfone (PES) polymer for the porous inner layer. Specifically, after obtaining asymmetric microporous PAI/PES dual-layer hollow fibers via non-solvent induced phase inversion, polyethyleneimine (PEI) polyelectrolyte modification on the outer PAI layer was applied to produce a nanofiltration (NF)-like thin layer, while the PES porous inner layer remained intact as PES is inert to PEI. The membrane morphology, structure and surface property were carefully tailored by adjusting polymer dope composition and spinning conditions. These membranes were subsequently characterized by a series of standard protocols in terms of membrane structure, permeability and salt rejection, and were utilized in FO process. It was found that the resultant dual-layer NF hollow fiber membrane can achieve pure water permeability of 15.9lm−2 h−1 bar−1 and a high rejection to divalent cations up to 89%. In FO process, the dual-layer hollow fiber exhibited a water flux of 27.5lm−2 h−1 in the orientation of active layer facing feed water by using 0.5MMgCl2 as draw solution and de-ionized (DI) water as feed at room temperature. The newly developed dual layer hollow fibers outperform all the single layer and dual-layer NF hollow fibers reported in the literature for FO applications. [Copyright &y& Elsevier]

Abstract: A new type of forward osmosis (FO) hollow fiber membranes with an antifouling nanofiltration (NF)-like selective layer has been developed in this work. The fabrication involves a step of porous poly(amide-imide) (PAI) ultrafiltration (UF) hollow fiber spinning via phase inversion, followed by simple polyelectrolyte post-treatments using positively charged polyethyleneimine (PEI) for cross-linking and negatively charged polystyrene sulfonate sodium salt (PSS) for deposition. The membranes are subsequently characterized by a series of standard protocols and evaluated in FO process. The PAI FO membranes possess a pure water permeability of 3.7–4.3Lm−2 h−1 bar−1 and Na2SO4 rejections up to 85% at 1bar. In the FO process, the membranes can achieve water flux of 17 and 12Lm−2 h−1 for active layer facing draw solution (AL-facing-DS) and active layer facing feed water (AL-facing-FW) configurations, respectively, using a 2000ppm Na2SO4 aqueous solution as the feed and 0.5M Na2SO4 as the draw solution. When the feed contained 1000ppm bovine serum albumin (BSA) and 2000ppm Na2SO4, a steady water flux of 11Lm−2 h−1 can be maintained using 0.5M Na2SO4 as the draw solution at ambient temperature of 23°C. The approach of making FO membranes developed in the present study offers the advantages of simple fabrication process, tailorable selective layer and promising membrane performance for protein-contained wastewater treatment by FO process. [Copyright &y& Elsevier]

Abstract: Hollow fiber membranes with a positively charged nanofiltration (NF)-like selective layer have been successfully fabricated by utilizing asymmetric microporous hollow fibers made of Torlon® polyamide–imide (PAI) material as the porous substrate followed by polyelectrolyte post-treatment using polyethyleneimine (PEI), which has not been reported previously. The reaction between PAI and PEI has been confirmed by experiments. The membrane structure and surface property are carefully tailored by adjusting polymer dope composition, spinning conditions and the post-treatment parameters. These membranes are, subsequently, characterized by a series of standard protocols in terms of membrane morphology, structure, permeability and salt rejection, and are applied in forward osmosis (FO) processes. The newly developed PAI hollow fiber membranes show a pure water permeability of 2.19–2.25L/m2 hbar and reasonable NaCl and MgCl2 rejections of 49% and 94% at 1bar, respectively. It is also found that in FO processes, when using 0.5M MgCl2 as a draw solution and DI water as the feed in the active layer facing feed water (AL-facing-FW) configuration at 23°C, the water fluxes of two PAI FO hollow fiber membranes are 8.36 and 9.74L/m2 h, respectively, and the J S /J V of the two membranes is smaller than 0.4g/L, which is lower than the data of 0.85g/L for commercial FO membrane from Hydration Technologies Inc. (HTI). Different from a neutral membrane, the positively charged FO membrane provides double electric repulsions to the salt transfer through the membrane in the AL-facing-FW configuration, leading to a reduction of salt penetration, while in the active layer facing draw solution (AL-facing-DS) configuration, the positive charges facilitate salt transportation. This study provides a simple and effective approach to make hollow fibers suitable for FO applications. [Copyright &y& Elsevier]

Interfacial polymerization is an effective technique to synthesize high performance polyamide thin film membranes. However, it is still very challenging to apply this technique on ceramic hollow fibres or tubular membranes, especially when the substrate pore size is in the microfiltration range. In this study, we demonstrated that thin polyamide layer can be synthesized directly on microfiltration ceramic tubular membranes with a surface pore size of 0.1–0.2 μm via interfacial polymerization without an intermediate layer. A thin polyamide layer with a thickness 30–40 nm was coated on the inner surface of the ceramic substrate by circulating the monomers of branched polyethyleneimine (PEI), piperazine (PIP), and trimesoyl chloride (TMC) through the membrane lumen. The thin film layer showed good integration with the ceramic substrate and could withstand high pressure of at least 10 bar. The mechanical property of the polyamide layer was examined using AFM and the modulus was measured. The thin film composite membranes demonstrated excellent nanofiltration performance with a pure water permeability of 16–18 LMH bar−1 and a molecular weight cut-off of ∼250 Da. The membranes also showed good salt rejections (>90%) to CaCl 2 , MgCl 2 and MgSO 4 , and still maintained high rejections of MgCl 2 and sucrose at elevated temperature of 80 °C. The use of highly inert ceramic substrates has enabled the application of polyamide membranes under more challenging conditions. Image 1 • PEI-based polyamide thin film was synthesized on microfiltration ceramic tubular membranes without an intermediate layer. • The membranes demonstrated excellent nanofiltration performance with a PWP of 16–18 LMH bar−1 and a MWCO of ∼250 Da. • The membranes also showed good divalent salt rejections for CaCl 2 , MgCl 2 and MgSO 4. • The rejections of MgCl 2 and sucrose remained high at elevated temperature of 80 °C. • The mechanical property of the polyamide film was studied using the AFM pinpoint mode and the modulus was measured. [ABSTRACT FROM AUTHOR]

In this study, the glutaraldehyde (GA) crosslinking was adopted in combination of layer-by-layer (LBL) polyelectrolyte deposition to develop a novel hollow fiber NF membrane with low-pressure water softening capability for synthesized hard water containing divalent counterion SO 4 2− . The challenges for the new membrane include (a) the presence of SO 4 2− in the feed water, which tends to deteriorate positively charged NF membrane retention to divalent ions; (b) high salinity feed water up to 10,000 ppm total dissolved salt (TDS); (c) 2 bar operating pressure that requires the membrane to have a good Mg 2+ /Na + selectivity and less mass transfer resistance in the substrate; and (d) better separation performance as compared with the state-of-the-art and commercial NF membranes. Based on the membrane characterization results, the possible structure of the deposited layers and the effect of GA crosslink was proposed. It was found that the crosslinking could tighten the membrane surface pores with increased hydrophilicity while the membrane surface charge was reduced. Therefore, mainly based on the size exclusion, the crosslinked LBL*1.5C membrane showed more than 10 LMH/bar permeability with above 95% rejection to each of 1000 ppm MgCl 2 , MgSO 4 and Na 2 SO 4 solution under 2 bar pressure. It was also proved to be more suitable for the low-pressure water softening application at 2 bar in all tested feed water with the presence of SO 4 2− and TDS up to 10,000 ppm in terms of both permeability and hardness removal efficiency when compared with commercial NF 270 and NF 90 membranes. [ABSTRACT FROM AUTHOR]

The layer-by-layer (LBL) polyelectrolyte deposited membranes have drawn increasing attention in various applications due to the ease of selective layer formation and their stability and versatility. In this study, the LBL deposition was performed at the inner surface of the polyethersulfone (PES) hollow fiber substrate to form composite nanofiltration (NF) membrane. The semi-dynamic deposition procedure was adopted with the aid of syringes. The newly developed inner deposited (id-LBL) membranes were then tested in NF and forward osmosis (FO) applications and the performance were compared with outer surface deposition as well as some literature data. The id-LBL membranes could not only withstand higher operating pressure but also possess superior hardness rejection especially in high concentration mixed salt solutions (more than 95% rejection to Mg 2+ and Ca 2+ in a 5000 ppm total dissolved salt (TDS) mixture under 4.8 bar). As for the FO process, with only two layer deposition, the id-LBL membranes also demonstrated significant performance improvement with increased water flux (up to 70 L/m 2 h using 0.5 M MgCl 2 as draw solution in active layer facing draw solution configuration) and reduced salt leakage (around 0.5 g/m 2 h using 1 M MgCl 2 draw solution in active layer facing feed water configuration). This study suggests that for hollow fiber substrate, the inner surface is more suitable for the formation of the selective layer via LBL deposition than the outer surface. [ABSTRACT FROM AUTHOR]

Abstract: Nanofiltration (NF) membrane process has become increasingly attractive due to their unique characteristics to selectively remove specific compounds or ions. The most commonly NF membranes are negatively charged which is unsuitable for hardness removal. Therefore, the development of novel NF membranes with a positively charged skin has become a key issue for low pressure water softening. In this study, dual layer microporous hollow fiber membranes were fabricated using Torlon poly(amide-imide) (PAI) as the material of the selective outer layer and polyethersulfone (PES) as the material of the porous support inner layer. A positively charged NF-like selective layer was developed by a simple polyelectrolyte cross-linking using polyallylamine (PAAm). The newly developed (PAI–PAAm)–PES dual layer hollow fiber membranes show a salt water permeability of 15.8 L/m2 h bar and high Mg2+ and Ca2+ rejections of 94.2% and 92.3%, respectively, at operating pressure of 2 bar using a 3000 ppm TDS feed solution. This study provides a simple and effective approach to produce positively charged NF hollow fiber membranes for water softening applications with low energy consumption. [Copyright &y& Elsevier]

Abstract: Composite nanofiltration (NF) hollow fiber membranes desirable for water softening under low operating pressure (<2bar) were successfully developed in the current study. The thin-film selective layer of the composite hollow fiber was formed through interfacial polymerization on the inner surface of a polyethersulfone (PES) ultrafiltration (UF) membrane substrate with branched polyethyleneimine (PEI) and trymesoyl chloride (TMC) employed as the monomers in aqueous and organic phases, respectively. It is found that a proper molecular weight of PEI and the presence of sodium dodecyl sulfate (SDS) in the aqueous phase are important for a successful interfacial polymerization reaction. The resulting membrane prepared with optimized preparation parameters possesses a positively charged thin-film selective layer with pure water permeability (PWP) of about 17l/m2 hbar and a molecular weight cut-off (MWCO) of around 500Da, which translates into the effective pore diameter of about 1.29nm. With combined separation mechanisms of Donnan exclusion and steric hindrance, it was possible to achieve MgCl2 and MgSO4 rejection of 96.7% and 80.6%, respectively, when tested for 1000ppm feed solutions at 2bar operating pressure. In addition, for a 3000ppm TDS feed stream containing salt mixtures, the membrane rejections for Mg2+ and Ca2+ ions were found to be around 90% while the water flux was about 20l/m2 h at 2bar pressure, suggesting the potential of the newly developed composite hollow fibers for effective water softening application. [Copyright &y& Elsevier]

• An acid-stable polyamine NF hollow fiber module was prepared for phosphorus recovery via the IP method. • Tannic acid interlayer was first constructed onto the PES substrate to assist the spreading of the aqueous phase. • The resultant NF membrane shows only 9.6% rejection of phosphorus, alongside over 93.5% rejection of metal ions at pH 2. • Membrane water permeability can reach 20.3 LMH/bar. The hazardous heavy metals coexisting with phosphorus-containing sewage sludge seriously limit phosphorus recovery. Nanofiltration (NF) membrane, which can selectively separate heavy metals and phosphorus, has a promising potential for recovering high-quality phosphorus from sewage sludge. In this work, we utilized the undissociated form of H 3 PO 4 at pH <2 and customized an acid-stable polyamine NF membrane via interfacial polymerization (IP) for separating phosphorus and heavy metals under acidic conditions. An interlayer formed via co-deposition of tannic acid (TA) and diethylenetriamine (DETA) was firstly coated onto the polyethersulfone (PES) hollow fiber module to assist the spreading of aqueous phase on the substrate surface. Consequently, a tight and positively charged polyamine layer with a mean pore size of 0.77 nm was successfully constructed on the PES substrate, which is smaller than that of the membrane without interlayer (1.39 nm). This polyamine membrane maintained excellent stability during 15-day acid testing with 0.1 M HCl as feed solution. When it was used to recover phosphorus at acidic condition (pH 2), the phosphorus rejection of the NF membrane was only 9.8 %, much lower than that at neutral pH (46.7 %), which is due to the fact that most phosphorus existed in the undissociated form of H 3 PO 4 at pH 2. Meanwhile, given the fine-tuning pore size and Donnan exclusion effect of this membrane, it could effectively retain 96.9 % of Mg2+ and over 93.5 % of most heavy metal ions such as Pb2+, Cu2+, Fe3+, Zn2+, and Cr3+, alongside outstanding water permeability of 20.3 LMH/bar at 2-bar operation pressure. This result demonstrates the potential of our homemade polyamine membrane in phosphorus recovery. [ABSTRACT FROM AUTHOR]

[Display omitted] • Microfiltration PTFE hollow fibres were transformed into durable, high value OSN membranes. • A PEI/PIP based polyamide thin film was successfully synthesized on PTFE hollow fibre substrates. • A two-time interfacial polymerization was conducted to obtain a defect-free polyamide layer. • The resultant membranes could withstand strong aprotic solvents like DMF and DMSO. • The membranes had high solute rejections, of up to 95 % methyl orange (327 Da) rejection in DMF. Polymeric membranes have been extensively studied for organic solvent nanofiltration (OSN) but many fail to show sufficient chemical resistance in strong solvents like dimethylformamide (DMF) and dimethyl sulfoxide (DMSO). This study focuses on harnessing the outstanding chemical resistance of polytetrafluoroethylene (PTFE), to develop polyamide-PTFE thin film composite (TFC) membranes that are resistant to such aprotic solvents. A defect-free polyamide thin film layer was successfully synthesized on the microfiltration PTFE hollow fibre substrates, overcoming challenges such as large and uneven pore size, and hydrophobicity of the PTFE substrates. A simple polydopamine (PDA) coating was carried out to improve the substrate's hydrophilicity prior to the polyamide synthesis via interfacial polymerization (IP). Polyethyleneimine (PEI) and trimesoyl chloride (TMC) were used as the monomers and a two-time IP method was employed to obtain a defect-free polyamide coating. The synthesized membranes showed high acetonitrile (ACN) and DMF permeabilities of 7.94 and 3.70 lm−2h−1bar−1, respectively, with acid fuchsin (585 Da) rejections of > 90 %. The molecular weight cut-off (MWCO) of the membranes could be further reduced to ∼300 Da by the addition of piperazine (PIP) monomers. The membranes also showed excellent stability and performance in a 72-hour OSN test performed in DMF indicating their great potential in effective molecular separation in harsh solvents. This study demonstrates how a simple modification and coating technique can transform commercially available microfiltration PTFE hollow fibres into durable and high value OSN membranes. [ABSTRACT FROM AUTHOR]

The use of nanotechnology in water separation membranes is a promising approach to alleviate the global water crisis. Graphene oxide (GO) with its unique water transport property has exhibited high potential for application in the water treatment processes. In this study, we have designed and fabricated a novel nanofiltration (NF)-like GO surface deposited poly(amide-imide)–polyethyleneimine (PAI–PEI) hollow fiber membrane. The PAI hollow fiber substrate was prepared by phase inversion and modified with PEI to obtain a positively charged membrane surface. The negatively charged GO nanosheets were then electrostatically immobilized onto the membrane surface via an instant dip-coating to form the NF-like selective layer. Our results have shown that the GO nanosheets serve as effective selective barriers and can achieve higher water permeability up to 86% without compromising membrane selectivity when used to substitute part of the PEI cross-linked selective layer. This is attributed to the smaller hydrodynamic resistance of GO nanosheets and their ability to effectively narrow the pore size distribution. Moreover, shortening of the membrane modification time and better mechanical properties of the GO modified membrane can be attained by avoiding excessive PEI cross-linking. The GO deposition also exhibits good stability when subjected to a backwashing pressure of 100,000 Pa and a cross-flow rate of 600 mL/min, which corresponds to a velocity of 14 cm/s and a Reynolds number of ~870. These results have demonstrated a high potential of using this GO modified hollow fiber membrane for large scale water softening applications. [ABSTRACT FROM AUTHOR]

The layer-by-layer (LbL) self-assembly is a common method for fabricating nanofiltration (NF) membranes. However, most multilayers are usually too thick and lack the necessary attributes to endow NF membranes with good permselectivity. In this study, we present a polyelectrolyte multilayered method by integrating dopamine as a "bio-glue". A three-step deposition was applied to the negatively charged PES substrate surface, following an alternate sequence of poly(allylamine hydrochloride) (PAH), dopamine (DA) and poly(sodium 4-styrenesulfonate) (PSS). The dopamine molecules were intercalated between the PAH and PSS layers to achieve a thinner thickness, higher hydrophilicity, smaller surface roughness and narrower pore size distribution. The resultant flat sheet (PAH/DA/PSS)4 polyelectrolyte multilayered (PEM) membranes exhibited enhanced water permeability (more than 60% increment from 13.5 to 21.9 LMH/bar) and higher rejection toward divalent ions (increasing MgCl 2 rejection from 91.0% to 94.8%) as compared with the control (PAH/PSS)4 NF membrane. Furthermore, the developed LbL method was applied on hollow fiber membrane modules and was able to achieve a higher Li+/Mg2+ selectivity from 15.6 to 37.8 and Na+/Mg2+selectivity from 11.0 to 19.1 using different simulated brines as feed solutions. On the whole, this polyelectrolyte multilayered method shows great potential for practical applications, including groundwater softening, seawater pretreatment and lithium extraction. [Display omitted] • A novel three-step LbL self-assembly method was proposed by integrating dopamine. • Dopamine intercalated selective layer exhibited a thinner and smoother surface. • The NF (PAH/DA/PSS)4 membrane showed better water permeability and higher divalent ion rejection. • Higher Na+/Mg2+ and Li+/Mg2+ selectivity was achieved due to the smaller pore size distribution. [ABSTRACT FROM AUTHOR]

Abstract: The layer-by-layer (LBL) polyelectrolyte deposition was applied on polyethersulfone (PES) hollow fiber ultrafiltration membrane to prepare nanofiltration (NF) membrane for low pressure water softening application for the first time. The effects of polyelectrolyte type and molecular weight (MW), deposited bilayer number, polyelectrolyte solution pH and supporting electrolyte concentration on the performance of resultant membranes were studied thoroughly. Experiments revealed that the pH of the polyelectrolyte solution and supporting electrolyte concentration presented the most notable effects. For weak poly-cations, Poly(ethylenimine) (PEI) and Poly(allylamine hydrochloride) (PAH), the solution pH affected the membrane performance significantly, and high water permeability and divalent cation rejection were obtained at optimum pH values. Using a low concentration of supporting electrolyte at underneath layers was proved to be an effective way to increase water permeability while maintaining high salt rejection. A salt water flux (SWP) of 12LMH/bar and 94% Mg2+ rejection was obtained by depositing only two bilayers of PSS/PAH polyelectrolytes on the PES substrate, while for the 3000ppm mixed salt solution, the water permeability was 11LMH/bar with Mg2+ and Ca2+ rejection as high as 90%. These promising results demonstrate that LBL technique is potentially applicable for preparing low-pressure water softening hollow fiber membranes. [Copyright &y& Elsevier]

Biocatalytic nanofiltration (NF) membranes incorporated with enzymes show high capacity for micropollutants (MPs) removal. However, there remains significant challenges such as the lack of molecular-level tailoring for skin layer design and effective strategy for enzyme immobilization. In this work, layer-by-layer (LBL) assembly based biocatalytic NF membranes were fabricated for bisphenol (BPA) removal by immobilizing laccase into the skin layer during the LBL polyelectrolytes assembly with controlled crosslinking and immobilization. This strategy enables simultaneous enzyme immobilization and NF skin layer formation. Three laccase immobilization strategies (i.e. , post immobilization, post crosslinking, and post crosslinking and immobilization) on skin layer were explored to prepare NF membrane for evaluating BPA removal efficiency. The post immobilization was identified as the optimal strategy, which endowed the biocatalytic NF membrane with a pure water permeability of 10.9 ± 0.4 LMH/bar and MgCl 2 rejection of 97.2 ± 0.3% under 2 bar pressure, alongside competitive laccase loading (238.8 ± 3.5 μg/cm2) and laccase activity (0.6 U/cm2). The optimal biocatalytic NF membrane exhibited an improvement in BPA removal of 79.5% under an incubation mode and 92.5% under a full recycling mode. The removal efficiencies were ~240% higher than that of the unmodified LBL membrane and clearly comparable to other reported biocatalytic membranes. This performance was attributed to the synergistic effect of membrane rejection, adsorption and laccase catalysis. The optimal biocatalytic NF membrane was found to be robust after six cycles within 14 days, while maintaining a relatively high BPA removal efficiency and salt rejection. Overall, our results open up a new avenue for enzyme immobilization into the skin layer of membranes for designing high-efficient biocatalytic NF membranes for MPs removal. Image 1 • Laccase-decorated LBL skin layer is prepared on lumen side of hollow fiber membrane. • Effects of different laccase immobilization strategies on BPA removal are explored. • Post immobilization strategy endows the membrane with a competitive NF performance. • Desired BPA removal efficiency is achieved with optimal biocatalytic membrane. • The long-term reusability and stability for BPA removal are confirmed. [ABSTRACT FROM AUTHOR]

Polyamide thin film membranes have shown outstanding performance in organic solvent nanofiltration (OSN). However, it is still challenging to produce polyamide hollow fibres for OSN, mainly due to limited solvent resistance of hollow fibre substrates and the difficulty to synthesize polyamide thin film on the surface of hollow fibre substrates. In this study, polyamide-based hollow fibre composite members for low pressure OSN were successfully developed. Solvent resistant polyimide hollow fibre substrates were first prepared through a non-solvent induced phase separation process, followed by chemical cross-linking with hexamethylene diamine. A polyamide thin film layer was then synthesized via interfacial polymerization, by circulating the reactant monomers including polyethyleneimine (PEI), piperazine (PIP) and trimesoyl chloride (TMC) through the hollow fibre lumen. The polyamide thin film with a thickness of ~60 nm was formed on the inner surface of the hollow fibre substrates. The membranes exhibited excellent nanofiltration (NF) performance under 2 bar operating pressure. The permeability of water, acetone and isopropanol was 6.8, 11.6 and 4.5 l m−2 h−1 bar−1, respectively. The membranes also achieved 99.9% and 91.8% rejection to rose bengal (1017 Da) and acid fuchsin (585 Da), respectively, in acetone. Furthermore, a 72-h filtration test was conducted and the membrane showed steady performance throughout the testing period. This study demonstrates the possibility of fabricating polyamide hollow fibre membranes for organic solvent nanofiltration at low pressure, which is desirable for practical applications. • Solvent resistant polyimide hollow fibre membranes were fabricated through chemical cross-linking. • Polyamide-based (PEI/PIP) layer was formed onto polyimide substrate to obtain a relatively loose selective layer. • Membranes achieved 11.6 and 4.5 l m−2 h−1 bar−1 permeability in acetone and isopropanol at 2 bar respectively. • Membranes maintained more than 90% rejection for acid fuchsin in 72-h filtration test, showing stable OSN performance. [ABSTRACT FROM AUTHOR]