Search

Tellurium (Te) is one of the elements with highest extinction coefficient κ at the 13.5 nm extreme-ultraviolet (EUV) wavelength. It is being considered as an alternative absorber material for binary photomasks in EUV lithography. The absorber material is required to remain chemically stable during EUV exposure, at elevated temperatures up to 150 °C, during mask cleaning, and in the low hydrogen pressure environment that is present in the EUV scanner. However, Te is known to react with oxygen and hydrogen, forming less EUV absorbing TeO2 and more volatile H2Te, respectively. Since the melting temperature of Te is only 449.5 °C at normal pressure, alloying Te with a more stable metal might result in a high κ material that will remain thermally and chemically stable over a wider range of operating conditions. In this paper, the authors report on the stability assessment of metal telluride (M-Te) alloys for the EUV absorber material. They combined Te with high κ metals, noble metals, and etchable metals. High κ and noble M-Te materials are both thermally more stable than etchable M-Te, but they cannot be patterned easily for use in an EUV photomask. High κ M-Te exhibits polycrystal morphology at room temperature compared to quasiamorphous noble M-Te though both can crystallize at a higher temperature. Hydrogen stability and cleaning solution stability of M-Te materials are improved considerably compared to Te, but their higher surface reactivity cannot be completely mitigated without the addition of an inert capping layer. Furthermore, etchable M-Te alloys are easily oxidized during deposition, resulting in lower electron density and hence lower κ. Nevertheless, M-Te alloys may be a way to stabilize Te for usage as the EUV absorber material. [ABSTRACT FROM AUTHOR]

In this work, we have studied the TMA/H2O (TMA = Al(CH3)3) atomic layer deposition (ALD) of Al2O3 on hydroxyl (OH) and thiol (SH) terminated semiconductor substrates. Total reflection x-ray fluorescence reveals a complex growth-per-cycle evolution during the early ALD reaction cycles. OH and SH terminated surfaces demonstrate growth inhibition from the second reaction cycle on. Theoretical calculations, based on density functional theory, are performed on cluster models to investigate the first TMA/H2O reaction cycle. Based on the theoretical results, we discuss possible mechanisms for the growth inhibition from the second reaction cycle on. In addition, our calculations show that AlCH3 groups are hydrolyzed by a H2O molecule adsorbed on a neighboring Al atom, independent of the type of backbonds (Si-O, Ge-O, or Ge-S) of AlCH3. The coordination of Al remains four-fold after the first TMA/H2O reaction cycle. [ABSTRACT FROM AUTHOR]

Wet etching offers an advantage as a soft, damage-less method to remove sacrificial material with close to nanometer precision which has become critical for the fabrication of nanoscale structures. In order to develop such wet etching solutions, screening of etchant properties like selectivity and (an)isotropy has become vital. Since these etchants typically have low etch rates, sensitive test structures are required to evaluate their etching behavior. Therefore, scaled-down single-crystalline Si (c-Si) and SiGe (c-SiGe) wagon-wheels were fabricated. First, the sensitivity of the c-Si wagon-wheels to detect anisotropic behavior of crystalline silicon in the alkaline etchants TMAH and NH4OH was demonstrated. Distinctive wagon-wheel patterns, characteristic for each material/etchant pair, were observed by top-down scanning electron microscopy (SEM) after anisotropic wet etching. Similar trends in crystallographic plane-dependent etch rates were obtained for both Si(100) and Si(110) substrates. Secondly, the etching of both c-Si and c-Si75Ge25 wagon-wheels in a typical selective etchant, peracetic acid (PAA), was evaluated. c-Si75Ge25 etching in PAA resulted in isotropic etching. Selectivity values were calculated based on two methods: the first by measurement of the sidewall loss of the spokes of the wagon-wheel, the second, indirect method, through measurement of the spoke retraction lengths. Both methods give comparable values, but the latter method can only be used after a certain critical etching time, after which the spoke tips have evolved toward a sharp tip. [ABSTRACT FROM AUTHOR]