Search

Carbon fiber paper (CFP) is one of the most widely used gas diffusion layer materials for proton exchange membrane fuel cells (PEMFC) due to its excellent properties such as high conductivity, high strength, high air permeability and corrosion resistance. In this study, CFP was prepared using the phenolic resin (PF) in-pulp addition method. The effect of PF content on the properties of hot-pressed paper (HPP) and CFP was investigated. The results showed that when the dosage of polyethylene oxide (PEO) was 1.5 wt%, the flocculation effect of PEO on PF was basically complete, and the water filterability and retention of carbon fiber pulp were relatively optimal. After HPP was carbonized into CFP, the hydrophobicity, average pore size, porosity, and air permeability increased, while the resistivity and tensile strength decreased. With the increase of PF content, the tensile strength of CFP gradually increased, while the average pore size, porosity, air permeability and resistivity decreased. When the PF content was 250 wt%, the average pore size of CFP was 36.5 μm, the water contact angle was 127°, the porosity was 69.7%, the air permeability was 7.81 × 103 mL mm/(cm2·h·mmHg), the resistivity was 21.1 mΩ cm, and the tensile strength was 15.7 MPa. In addition, the CFP prepared using PF in-pulp addition method had a relativity uniform pore size distribution and high air permeability. Therefore, this work shows that the CFP prepared using this technique exhibits excellent comprehensive performance, and enables the manufacturing of CFP to be more efficient, low-cost, and environmentally friendly. [Display omitted] • Carbon fiber paper was prepared efficiently using the phenolic resin in-pulp addition method. • Polyethylene oxide exhibits strong adsorption ability on phenolic resin in carbon fiber pulp. • The melting temperature of phenolic resin is a critical point in the preparation process of carbon fiber paper. • Carbon fiber paper possesses a relatively uniform pore size distribution and high air permeability. [ABSTRACT FROM AUTHOR]

• Pulp and paper mill sludge (PPMS) landfill sites have GHG assessment challenges. • GHG fluxes measured by chambers with (F +) and without (F-) a frame were compared. • Flux relationships up to 80 % were shown between F- and F + chambers (the standard) • Correction factors for F- chambers were built to estimate fluxes from F + chambers. • The approach can refine GHG inventories on PPMS landfill sites. Assessments of greenhouse gas (GHG) emissions in managed areas are facing various challenges. A non-flow-through, non-steady-state (NFT-NSS) chamber coupled to a frame permanently inserted into the landfilled substrates is a standard method for quantifying GHG emissions in managed areas, such as pulp and paper mill sludge (PPMS) landfill sites. Frequent measurements are needed to minimize uncertainties on GHG emission factors at the landfill site scale. However, maintaining a frame inserted into the substrates for a long time period is often impossible due to landfilling management operations. Therefore, GHG measurements using NFT-NSS chambers placed directly on substrates' surface could be an interesting option. Our objectives were to determine the relationships between CO 2 , CH 4 , and N 2 O fluxes measured with (F +) and without (F-) a frame inserted in the substrates' surface and to develop correction factors for fluxes measured without a frame. Measurements were made at different PPMS landfill sites in the province of Québec, Canada. Stronger GHG flux relationships were observed at the provincial (across sites) than the specific site scale: the variance in GHG fluxes from F- chambers explained up to 80 % of variance in fluxes from F + chambers. The measured CO 2 , CH 4 , and N 2 O fluxes in F- chambers were on average 53, 78, and 63 % lower, respectively, than those estimated by the models at provincial scale. The correction factors developed with this approach could greatly extend the number of sites where in situ GHG measurements can be done and would help refining GHG inventories at the provincial and national levels. [ABSTRACT FROM AUTHOR]

Development of low-cost, efficient, and stable oxygen evolution electrocatalysts is crucial for the conversion and storage of renewable energy. Therefore, an effective integrated heterostructure catalyst is needed to achieve a lower overpotential during oxygen evolution process. In this paper, cobalt-zinc bimetallic MOF precursors are used as templates to prepare bimetallic cobalt-based selenides with good oxygen evolution catalytic activity and stability on carbon fiber paper. Due to the high specific surface area and porous structure of the coupling structure of nanorods and polyhedra, and the strong electronic coupling between CoSe 2 and ZnSe on nanorods. CoSe 2 -ZnSe/CP exhibits excellent electrocatalytic activity in 1 M KOH solution. It only requires an overpotential of 275 mV to reach the current density of 10 mA cm-2, and the Tafel slope is 68.9 mV dec-1. In addition, after 12 h of continuous operation of CoSe 2 -ZnSe/CP, the activity decay of the catalyst is negligible. This work provides a method for the design of heterogeneous bimetallic selenide integrated oxygen evolution electrocatalysts. [Display omitted] • The CoSe 2 -ZnSe/CP catalyst is obtained by selenization of MOF precursor at high temperature. • The catalyst has unique nanorod-coupled polyhedral morphology and high specific surface area. • The strong electron coupling between CoSe 2 and ZnSe improves the oxygen evolution activity. • CoSe 2 -ZnSe/CP exhibits low overpotential, high exchange current density and fast kinetics. [ABSTRACT FROM AUTHOR]

Carbon paper is one of the most widely used gas diffusion layer substrate materials due to its stable performance, relatively low cost, and easy for subsequent processing. Water-soluble phenolic resin, which is more ecologically friendly than alcohol-soluble phenolic resin, was used to prepare carbon paper as the precursor of the carbon matrix. And the effect of different resin solution concentrations on the properties of carbon paper was explored. The results showed that the graphitization, electrical conductivity and mechanical properties of carbon paper increased with the increase of resin solution concentration. When the concentration of resin solution was 20 wt%, the performance of carbon paper was relatively optimal. The graphitization of the carbon paper reached 65.45%, the porosity reached 80.74%, the resistance value at 1 MPa pressure was only 7.61 mΩ cm2, the tensile strength was 1.57 MPa, and the elastic modulus was 1210.98 MPa. [ABSTRACT FROM AUTHOR]

Carbon paper as a macroporous substrate of gas diffusion layer in proton exchange membrane fuel cells directly impacts the output performance of cells. In this study, we present a straightforward strategy to improve the overall performance of carbon paper by mixing short/long (6mm/10 mm) chopped carbon fibers at an optimal concentration of phenolic resin. The results show that incorporating longer carbon fibers can increase the porosity, conductivity, gas flux, and mechanical properties of carbon paper. The membrane electrode assembly achieved a peak power density of 1182.61 mW cm−2 at 60% RH using carbon paper with a long carbon fiber content of 40 wt% and an impregnation concentration of 10 wt%. This outperforms commercially available carbon paper. Based on electrochemical impedance spectroscopy results, it was confirmed that our carbon paper had a lower mass transfer resistance of only 32.17 mΩ cm−2 under conditions of 2 A cm−2 and 60% RH. This was due to its sparser three−dimensional network-like pore structure which was created by mixing different lengths (6mm/10 mm) of carbon fibers. This work provides new insights into preparing high−performance carbon papers. • The nature of carbon paper is regulated by mixing short/long (6mm/10 mm) CFs ratio. • The long carbon fiber contents of 20–40 wt% present better physical properties. • The optimal carbon papers can mitigate mass transfer resistance. • MEA composed of the optimal CP shows a higher power density than commercial CP. [ABSTRACT FROM AUTHOR]

A facile method is proposed in this work to prepare a carbon paper (CP) with outstanding properties by doping boron to catalyze graphitization at lower temperature. Boron was introduced into CP by impregnating carbon fiber preform into a boron/phenolic resin/ethanol solution, and then CP was obtained after the consecutive procedures of hot pressing, carbonization, and graphitization. Morphology, microstructure, composition, and physical properties of the doped and undoped CPs were thoroughly investigated via various techniques to exam the effects of boron concentration and graphitization temperature. Furthermore, the boron doped CP was fabricated into fuel cell gas diffusion layer (GDL) and membrane electrode assembly (MEA) to evaluate its performance through the single cell performance. The findings indicated CP doping with 2 wt% boron could lower the graphitization temperature by at least 200 °C. The B-doped GDL had a higher power density in comparison with the undoped GDLs made in our lab or from the commercial brands. • The innovative preparation method for carbon paper with high conductivity. • The effect of boron concentration and graphitization temperature on carbon paper. • The single cell performance of B-doped gas diffusion layer. [ABSTRACT FROM AUTHOR]

Enzymes derived from microbial sources have gained increasing popularity in industrial applications over the past decades. Despite the high production cost, alkaline proteases have wide applications in industries such as tanneries, food production, and detergents. In recent years, there has been a shift towards utilizing natural carbon sources for cultivating microorganisms and extracting proteases in order to reduce production costs. This study aimed to investigate the biochemical and kinetic properties of protease enzymes obtained from Aspergillus niger cultivated in a paper waste medium and compare with the enzyme produced in a basal medium. Glucose is a more favorable carbon source compared to cellulose, so paper waste was pretreated with cellulose-degrading bacteria to convert cellulose into smaller carbohydrates. After the growth of A. niger in basal and combinational media, the enzymatic properties were compared between the extracted enzymes by using casein as substrate. The results demonstrated that A. niger could produce protease enzymes in the paper waste medium similar to the basal medium with more than 5-fold cost saving. The specific activity of the enzymes isolated from the basal and paper waste media was calculated to be 184.95 ± 10.56 U ml−1 and 169.88 ± 11.05 U ml−1, respectively. Carbon sources did not affect the optimum pH and temperature of the protease enzyme, which were found to be 8 and 37 °C, respectively. This study provides valuable insights into the production of alkaline protease from A. niger using a combinational medium (paper waste pretreated by cellulose-degrading bacteria), offering a cost-effective approach for industrial applications. [ABSTRACT FROM AUTHOR]

Citation scores (CS) have been traditionally used to measure the impact of scientific publications. Sourced from the Internet, Altmetric Attention Scores (AAS) are complementary metrics that assess how often publications are discussed and used globally. We compared by rank the top 500 papers by CS and AAS published in Clinical Nutrition with corresponding AAS and CS. A search for all publications in Clinical Nutrition was performed on Dimensions (https://app.dimensions.ai/discover/publication) on 3rd April 2024. Outputs were ranked according to CS and then by AAS with the top 500 in each category selected. Scores, year and type of publication were recorded. Correlation was expressed as the Spearman's rank coefficient (ϱ). We identified 18,790 outputs. Within the top 500 publications ranked by CS, there was a significant weak positive correlation (ϱ = 0.235, P < 0.0001) between CS [median (IQR) 149 (116–223)] and AAS [7 (3–22)]. Ranked by AAS, there was a non-significant very weak positive correlation (ϱ = 0.072, P = 0.106) between AAS [55.5 (36–115)] and CS [42 (16.5–94.5)]. Trends remained similar when grouped by publication type. Guidelines, ranked by CS, had the highest CS and ranked by AAS, the highest CS and AAS. Publications per year, by year, ranked by CS, had a negatively skewed distribution peaking in 2012 and declined thereafter, but when ranked by AAS, had a moderately positive linear trend from 2001 to 2024 (ϱ = 0.513, P < 0.0001). Correlation between CS and AAS was weak. Guidelines had the highest CS and AAS. CS are iterative taking years to mature while AAS are immediate. [ABSTRACT FROM AUTHOR]

Primary care healthcare professionals (PCHPs) are pivotal in managing chronic diseases and present a unique opportunity for nutrition-related disease prevention. However, the active involvement of PCHPs in nutritional care is limited, influenced by factors like insufficient education, lack of resources, and time constraints. In this position paper The European Society for Clinical Nutrition and Metabolism (ESPEN) promotes the active engagement of PCHPs in nutritional care. We emphasize the importance of early detection of malnutrition by screening and diagnosis, particularly in all individuals presenting with risk factors such as older age, chronic disease, post-acute disease conditions and after hospitalization for any cause. ESPEN proposes a strategic roadmap to empower PCHPs in clinical nutrition, focusing on education, tools, and multidisciplinary collaboration. The aim is to integrate nutrition into medical curricula, provide simple screening tools for primary care, and establish referral pathways to address malnutrition systematically. In conclusion, we urge for collaboration with PCHP organizations to raise awareness, enhance nutrition skills, facilitate dietitian accessibility, establish multidisciplinary teams, and promote referral pathways, thereby addressing the underestimated clinical challenge of malnutrition in primary care. [ABSTRACT FROM AUTHOR]

The solar photocatalytic degradation of pulp and paper mill wastewater has been reported by several scientists. However, this is the first time we are reporting for solar photocatalytic hydrogen production from pulp and paper mill wastewater and simultaneous degradation of pollutants. In this work, CuO based photocatalysts and novel square type photocatalytic reactor of 5 L capacity were used. The result shows that the prepared photocatalysts are solar active, efficient in hydrogen recovery and pollutant degradation from the pulp and paper wastewater. The effects of catalyst loading, sacrificial agent, pollutant removal efficiency and stability check were investigated. At 0.25 g/L of CuO/Fe 2 O 3 , 0.2 M of sacrificial agent (Na 2 SO 3 2−) and hydrogen yield of 1000 mL from 1000 mL of wastewater was achieved. The removal efficiency of TSS, TDS, BOD, COD, turbidity and TOC are around 70, 50, 60, 65, 70 and 45% respectively. Reusability study revealed that CuO/Fe 2 O 3 was chemically stable and could be reused successively (five cycles) without significant changes in its photoactivity and intrinsic properties. [Display omitted] • Visible light active CuO mixed with novel metal oxides were employed. • Hydrogen recovery from black liquor, paper mill wastewater were 1000 mL/h/L and 850 mL/h/L. • Efficiency of degradation of pulp & paper wastewater chemicals were around 50–70%. • AcHieved high recovery of hydrogen from pulp & paper wastewater. [ABSTRACT FROM AUTHOR]

Paper mulching films are affected by wind and rain in the field, which lead to the problems of water absorption, shrinkage, and friction with the soil surface. In order to achieve better hydrophobic durability and wear resistance of paper mulching films, a paper mulching film with ZnO/SiO 2 composite coating was prepared by the brush coating method. Taking ceramic balls as friction pairs, reciprocating friction tests were carried out with two kinds of paper mulching films at different temperatures. The morphology of the raw paper mulch film and the ZnO/SiO 2 composite-coated paper mulch film after rubbing at different temperatures and the reason of the hydrophobic durability of the coated paper mulch film were analyzed using a scanning electron microscope and a three-dimensional topography instrument. The results show that ZnO/SiO 2 composite coating can improve the wear resistance and hydrophobic durability of the paper mulch film. Through surface morphology analysis, it can be found that the composite coating plays a role in modification and filling and improves the adhesion between the fibers by reducing the pores on the surface of the paper mulch film, finally improving the wear resistance and hydrophobic durability of the paper mulch film. [ABSTRACT FROM AUTHOR]

The present paper reflects the position of the Italian Association for Neuroendocrine Tumors (Itanet), the Italian Society of Gastroenterology (SIGE), and the Italian Society of Digestive Endoscopy (SIED) regarding the management of patients affected by gastric, duodenal, and rectal neuroendocrine neoplasms (NENs) amenable to endoscopic treatment. The key questions discussed in this paper are summarized in Table 1. Data were extracted from the MEDLINE database through searches; expert opinions and recommendations are provided in accordance with the available scientific evidence and the authors' expertise. Recommendations are presented alongside a level of evidence and grade of recommendation based on the GRADE system. This paper specifically focuses on subgroups of NENs considered suitable for endoscopic management according to current international guidelines: i. well-differentiated gastric neuroendocrine tumors (gNET) type 1 < 2 cm and selected cases of type 3; ii. well-differentiated duodenal, non-functioning, non-ampullary NET with size < 2 cm; and well-differentiated rectal NET with size < 2 cm. [ABSTRACT FROM AUTHOR]

Digital cytology and artificial intelligence (AI) are gaining greater adoption in the cytopathology laboratory. However, peer-reviewed real-world data and literature are lacking regarding the current clinical landscape. The American Society of Cytopathology in conjunction with the International Academy of Cytology and the Digital Pathology Association established a special task force comprising 20 members with expertise and/or interest in digital cytology. The aim of the group was to investigate the feasibility of incorporating digital cytology, specifically cytology whole slide scanning and AI applications, into the workflow of the laboratory. In turn, the impact on cytopathologists, cytologists (cytotechnologists), and cytology departments were also assessed. The task force reviewed existing literature on digital cytology, conducted a worldwide survey, and held a virtual roundtable discussion on digital cytology and AI with multiple industry corporate representatives. This white paper, presented in 2 parts, summarizes the current state of digital cytology and AI practice in global cytology practice. Part 1 of the white paper presented herein is a review and offers best practice recommendations for incorporating digital cytology into practice. Part 2 of the white paper provides a comprehensive review of AI in cytology practice along with best practice recommendations and legal considerations. Additionally, the results of a global survey regarding digital cytology are highlighted. • The American Society of Cytopathology in conjunction with the International Academy of Cytology and the Digital Pathology Association established a special task force comprising 20 members with expertise and/or interest in digital cytology to investigate the feasibility of incorporating digital cytology and artificial intelligence applications into the workflow of the laboratory. • The task force reviewed existing literature on digital cytology, conducted a worldwide survey, and held a virtual roundtable discussion on digital cytology and artificial intelligence with multiple industry corporate representatives. • Part 1 of the white paper presented herein is a review and offers best practice recommendations for incorporating digital cytology into practice. [ABSTRACT FROM AUTHOR]

Digital cytology and artificial intelligence (AI) are gaining greater adoption in the cytology laboratory. However, peer-reviewed real-world data and literature are lacking in regard to the current clinical landscape. The American Society of Cytopathology in conjunction with the International Academy of Cytology and the Digital Pathology Association established a special task force comprising 20 members with expertise and/or interest in digital cytology. The aim of the group was to investigate the feasibility of incorporating digital cytology, specifically cytology whole slide scanning and AI applications, into the workflow of the laboratory. In turn, the impact on cytopathologists, cytologists (cytotechnologists), and cytology departments were also assessed. The task force reviewed existing literature on digital cytology, conducted a worldwide survey, and held a virtual roundtable discussion on digital cytology and AI with multiple industry corporate representatives. This white paper, presented in 2 parts, summarizes the current state of digital cytology and AI practice in global cytology practice. Part 1 of the white paper is presented as a separate paper which details a review and best practice recommendations for incorporating digital cytology into practice. Part 2 of the white paper presented here provides a comprehensive review of AI in cytology practice along with best practice recommendations and legal considerations. Additionally, the cytology global survey results highlighting current AI practices by various laboratories, as well as current attitudes, are reported. • The American Society of Cytopathology in conjunction with the International Academy of Cytology and the Digital Pathology Association established a special task force comprising 20 members with expertise and/or interest in digital cytology to investigate the feasibility of incorporating digital cytology and artificial intelligence applications into the workflow of the laboratory. • The task force reviewed existing literature on digital cytology, conducted a worldwide survey, and held a virtual roundtable discussion on digital cytology and artificial intelligence (AI) with multiple industry corporate representatives. • Part 2 of the white paper presented here provides a comprehensive review of artificial intelligence in cytology practice along with best practice recommendations and legal considerations. [ABSTRACT FROM AUTHOR]

[Display omitted] • The healthcare system is a significant contributor to global warming. • Cardiac electrophysiology mainly uses high-tech single-use medical devices. • Worldwide complex supply chain for medical treatment, particularly medical devices. • The complex supply chain has led to device shortages. • Reprocessing of medical devices labelled single use could be part of the solution. • All stakeholders must engage sustainability efforts. Sustainability in healthcare, particularly within the domain of cardiac electrophysiology, assumes paramount importance for the near future. The escalating environmental constraints encountered necessitate a proactive approach. This position paper aims to raise awareness among physicians, spark critical inquiry and identify potential solutions to enhance the sustainability of our practice. Reprocessing of single-use medical devices has emerged as a potential solution to mitigate the environmental impact of electrophysiology procedures, while also offering economic advantages. However, reprocessing remains unauthorized in certain countries. In regions where it is possible, stringent regulatory standards must be adhered to, to ensure patient safety. It is essential that healthcare professionals, policymakers and manufacturers collaborate to drive innovation, explore sustainable practices and ensure that patient care remains uncompromised in the face of environmental challenges. Ambitious national/international programmes of disease prevention should be the cornerstone of the strategy. It is equally vital to implement immediate actions, as delineated in this position paper, to bring about tangible change quickly. [ABSTRACT FROM AUTHOR]