Search

This paper describes a flow control of the dye in the paper mill with the quasi-Z-source indirect matrix converter (QZSIMC) fed induction motor drive. More than a decade the voltage-source inverter (VSI) and current-source inverter (CSI) have been used to control the speed of the induction motor, which in turns controls the flow of dye. Recently, the matrix converter (MC) has been an excellent competitor for the VSI or CSI for its compactness. The voltage transfer ratio of the VSI, CSI, and MC has been limited to 0.866. Thus, the efficiency of these converters is less. To improve the voltage transfer ratio the quasi-Z-source network (QZSN) is to be used between voltage source and indirect MC (IMC). The modification in the shoot-through duty ratio of the QZSN varies the voltage transfer ratio greater than 0.866. Different voltage transfer ratios are needed for different voltage sag conditions. For a variation of the duty ratio of the QZSN, the fuzzy logic controller has been presented. To control the IMC vector control with space vector modulation has been presented. This paper proposes the implementation of QZSIMC adjustable speed drive for the flow control of dye in paper mill during different voltage sag conditions. A 4-kW prototype has been built and the effectiveness of the proposed system is verified with simulation results and experimental setup. Simulation is done in MATLAB, Simulink platform. Experimental setup is done with the aid of a TMS320F2812 (Texas Instrument) processor. The experimental results validate the maintenance of the speed of an induction motor at the set condition, thus controlling the perfect flow of dye in paper manufacturing technology. [ABSTRACT FROM AUTHOR]

Paper-based digital microfluidic biochips (P-DMFBs) have recently emerged as a promising low-cost and fast-responsive platform for biochemical assays. In P-DMFBs, electrodes and control lines are printed on a piece of photograph paper using an inkjet printer and carbon nanotubes (CNTs) conductive ink. Compared with traditional digital microfluidic biochips (DMFBs), P-DMFBs enjoy significant advantages, such as faster in-place fabrication with printer and ink, lower costs, and better disposability. Since electrodes and CNT control lines are printed on the same side of this paper, a critical design challenge for P-DMFB is to prevent control interference between moving droplets and the voltages on CNT control lines. Control interference may result in unexpected droplet movements and thus incorrect assay outputs. To address this design challenge, a control-fluidic codesign methodology is proposed in this paper, along with two demonstrative design flows integrating both fluidic design and control design, i.e., the droplet-oriented codesign flow and the electrode-oriented codesign flow. The droplet-oriented flow is suitable for designing biochips with sparse electrodes and relatively larger number of droplets, whereas the electrode-oriented flow is suitable for biochips with dense electrodes and smaller number of droplets. The computational simulation results of real-life bioassays demonstrate the effectiveness of the proposed codesign flows. [ABSTRACT FROM AUTHOR]

An oil-paper insulation system which will withstand DC voltage under normal conditions is a key component of converter transformers as well as high voltage direct current (HVDC) bushings. When the system changes its state, operating overvoltage appears. This kind of overvoltage will consequently affect the application of oilimmersed facilities and the safety of entire grid. Therefore, this paper studies the charge coupling behavior of double-layer oil-paper insulation under DC and pulse voltages. From the research of different pulse voltage amplitudes, pulse numbers and polarity, conclusions can be drawn that, with the increase of the pulse voltage amplitudes, DC and pulse voltages in the same polarity cause the absolute value of the initial surface potential to decrease and then rise; while in different polarities, the charge with the same polarity as the pulse voltage increases. Furthermore, for the same pulse voltage, the absolute initial value of the DC voltage applied in the same polarity is higher than that in different polarities. Considering the pulse number effect, it is obvious that the initial value increases with the increase in the pulse number, and then reaches saturation. Also, with the increase in pulse number, the decay rate decreases and thus the charge is slowly dissipated. From the tdV/dt and the decay time curves, the peak value increases with the increase in the pulse number, while the characteristic time varies by the polarity of the DC and pulse voltages. [ABSTRACT FROM AUTHOR]

Main insulation of windings connected with valves in high voltage direct current (HVDC) convert transformers withstands pulsating DC voltages. This paper presents breakdown properties of oil-impregnated paper under pulsating DC voltages at different temperatures. Progressive stress tests were carried out to obtain breakdown voltages of oil-impregnated paper with thickness of 0.2 mm under pulsating DC voltages at different temperatures. Constant stress tests were executed to measure time to breakdown of the oil-paper specimens. Both types of the experiments were also undertaken under either AC or DC voltages. An electrical aging lifetime model was proposed for the oil-impregnated paper, and parameters of the electrical aging lifetime model were presented. Experiments and analysis results show that the breakdown voltages and time to breakdown of oilpaper insulation are influenced by temperature significantly. [ABSTRACT FROM PUBLISHER]

The work reported in this paper aims at developing an algorithm for system operators to solve a robust security-constrained AC optimal power flow (R-SC-ACOPF) problem, which also optimizes the settings of discrete controllers including load tap changers (LTCs) and shunt capacitor banks (SCBs). An iterative algorithm involving a master problem and a number of sub-problems is proposed. The master problem selects the optimal discrete controllers’ settings by taking into account primal SC-ACOPF constraints based on the single-component worst contingencies identified by the sub-problems. Each sub-problem is a bi-level max-min problem used to find the current worst contingency. The overall objective is to minimize the total cost, including generation and load shedding cost, while satisfying all relevant constraints. The master problem and sub-problems allow representing LTC tap positions, SCB status, and contingencies using binary variables. Two case studies are presented as applications of this novel technique. [ABSTRACT FROM AUTHOR]

Voltage rise caused by high levels of distributed generation is manifesting as voltage regulation challenges for many electricity network service providers. In this environment it would be ideal to reduce supply voltage magnitudes, however, many network operators are hesitant to do so due to concerns related to consumer appliance performance at reduced supply voltage magnitudes. Voltage regulation requirements are defined by network standards and network service providers must ensure voltages remain within specified limits. Through an evaluation of domestic appliance performance when supplied at various voltage magnitudes, this paper examines the impact of varying voltage levels on residential appliances. Equipment energy demand, operation and actuation were monitored for each applied voltage magnitude. While no equipment failures were recorded, appliance behaviour varied significantly with applied voltage magnitude. Individual appliance conservation voltage reduction (CVR) factors have also been established. The results highlight the importance of good voltage regulation and provide substantiated appliance performance figures for future studies. The outcomes of this paper allow electricity network service providers to understand the implications of supply voltage magnitude on domestic appliance performance, whether it be understating of the impact of higher voltage magnitudes caused by distributed generation or implications of reducing voltage magnitudes to provide headroom for distributed generation integration. [ABSTRACT FROM AUTHOR]

Negative-sequence current is required to be intentionally injected to support the power grid or compensate the imbalanced load in asymmetrical faults utilizing STATCOM. However, the extreme compensation range of negative-sequence current injection becomes complicated when grid voltage becomes asymmetrical. This article presents a novel off-line strategy for negative-sequence current compensation under two typical kinds of asymmetrical grid faults — single-phase voltage drop and double-phase voltage drop, with the following two benefits simultaneously: maximizing negative current compensation capacity; avoiding iterations and reducing computation burdens. In this paper, the mechanism of DC voltage balancing among three phases in STATCOM is analyzed and a new identification method of negative-sequence current compensation range is explored out. To simplify the calculation, this paper takes the ratio of negative-sequence reactive (Iq-) and active (Id-) current as a variable (s). In this way, the relationship between the extreme compensation range, asymmetrical voltage sag depth of power grid h is drawn with MATLAB. Different from the previous iterative method, the off-line identification method is applied to avoid huge iterations. By fitting the curve, the precise ranges of negative-sequence current compensation under different asymmetrical grid faults are approximated as simple polynomials, thus significantly reducing the computation burdens. Simulation and experimental results verify the practicability of the proposed compensation method. [ABSTRACT FROM AUTHOR]

Although smart home has received wide attention in recent years, numerous scholars focus more on energy optimization strategy than energy dispatch hardware device (named energy router). Meanwhile, this energy router should have several features, i.e., high renewable energy utilization, energy multi-port and low volume. Thus, this paper designs a nine-port energy router regarding smart home and proposes a multimode hierarchical management strategy for this energy router. First, for the multi-port demand of wind, solar, storage and utilization, this paper presents a nine-port energy router to improve the renewable energy consumption and power supply flexibility. In addition, to reduce the volume of the energy router, a non-isolated AC/DC hybrid topology is constructed through embedding the integrated power electronic converters, which achieves the miniaturization of the energy router. In order to improve the renewable energy utilization rate, the decentralized module control is proposed for the components of energy router to provide the voltage and frequency support for system, and realizes the power sharing of distributed generations (DGs). Furthermore, the power exchange control with three-mode switching is proposed to guarantee the global energy flow balance under complex conditions. Eventually, the feasibility of the energy router is verified by the simulation and experiments. [ABSTRACT FROM AUTHOR]

In many power systems, the increased penetration of inverter-based renewable generation will cause a decrease in kinetic energy storage, leading to higher frequency excursions after a power disturbance. This is the case of the future Nordic Power System (NPS). The look-ahead study reported in this paper shows that the chosen units participating in Frequency Containment Reserves (FCR) cannot keep the frequency above the prescribed threshold following the outage of the largest plant. This analysis relies on a detailed model of the Northern European grid. The latter is compared to the classical single-mass equivalent, and the impact of voltage-dependent loads is assessed in some detail. Next, the paper focuses on emergency power control of the HVDC links that connect the NPS to the rest of the European grid, which can supplement or even replace part of the FCR. The proper tuning of that control is discussed. Finally, the analysis is extended to the HVDC links connecting the future North Sea Wind Power Hub under two configurations, namely low and zero inertia. The impact of outages in the latter sub-system is also assessed. The material to simulate the system with industrial software is made publicly available. [ABSTRACT FROM AUTHOR]

The paper proposes a control scheme to improve the dynamic response of power systems through the automatic regulators of converter-based Distributed Energy Resources (DERs). In this scheme, both active and reactive power control of DERs are varied to regulate both frequency and voltage, as opposed to current practice where frequency and voltage controllers are decoupled. To assess the proposed control against the current state-of-art, the paper also defines a metric that captures the combined effect of frequency/voltage response at any given bus of the network. Results indicate that the proposed control strategy leads to a significant improvement in the stability and performance of the overall power system. These results are based on a comprehensive case study carried out by employing a modified version of the IEEE 39-bus benchmark system, where a portion of the synchronous machines is substituted by converter-interfaced DERs. The impact on the proposed control of load models, the $R/X$ ratio of network lines, as well as the level of DER penetration to the grid, are properly evaluated and conclusions are duly drawn. [ABSTRACT FROM AUTHOR]

Voltage-controlled three-phase three-leg inverters are widely applied in various occasions. The inverters are generally switched to the current-controlled mode to limit the fault currents when short-circuit faults happen. Under symmetrical fault, the inverter can be controlled as a symmetrical, three-phase current source. However, the voltage limiting will happen under asymmetrical fault. As a result, the fault phase currents will be distorted and cannot be completely controlled. Considering that the voltage limiting is mainly caused by large load impedance of healthy phase under asymmetrical fault, the voltage limiting is avoided by paralleling the virtual impedance with the output filter capacitor in this paper. As a result, the current limiting loop is not broken and the fault phase currents can be effectively controlled. The implementation of virtual impedance in control system and the influence of virtual impedance on the stability of system are also analyzed in detail in this paper. The theoretical results are validated by experiments. [ABSTRACT FROM AUTHOR]

This paper presents the three-phase impulse overvoltage measured at the terminal of a 10 kV distribution line when the impulse current was injected into the phase conductor of the distribution line. The overvoltage observation station was installed at the terminal of the line to record the three-phase overvoltage waveforms. It is shown that the struck phase overvoltage consists of three components including the negative pulse, the stage of residual voltage maintenance and the overshoot oscillation part. The observed negative peak values of the struck phase overvoltage range from −85.4 kV to −96.0 kV in three different injected impulse levels at 90,120,150 kV charging voltage. The duration of residual voltage depends on the duration time of injected current. Furthermore, there is a strong positive relationship between the oscillation amplitude of the struck phase overvoltage and the injected current amplitude. The peak amplitudes of three-phase overvoltage always have the following magnitude relationship: struck phase C > induced phase B > induced phase A. The voltage coupling coefficients of induced phases will not exceed 0.4. The test method proposed in this paper will be helpful to the research on the lightning overvoltage response characteristics of the distribution line and the protection analysis of arresters. [ABSTRACT FROM AUTHOR]

Electric distribution grid operations typically rely on both centralized optimization and local non-optimal control techniques. As an alternative, distribution system operational practices can consider distributed optimization techniques that leverage communications among various neighboring agents to achieve optimal operation. With the rapidly increasing integration of distributed energy resources (DERs), distributed optimization algorithms are growing in importance due to their potential advantages in scalability, flexibility, privacy, and robustness relative to centralized optimization. Implementation of distributed optimization offers multiple challenges and also opportunities. This paper provides a comprehensive review of the recent advancements in distributed optimization for electric distribution systems and classifications using key attributes. Problem formulations and distributed optimization algorithms are provided for example use cases, including volt/var control, market clearing process, loss minimization, and conservation voltage reduction. Finally, this paper also presents future research needs for the applicability of distributed optimization algorithms in the distribution system. [ABSTRACT FROM AUTHOR]

This paper proposes an optimization approach for day-ahead reactive power planning to improve voltage security in transmission networks. The problem is formulated as a voltage-secure multi-period optimal reactive power dispatch (MP-ORPD) problem. The optimization approach searches for optimal set-points of dynamic and static reactive power (var) resources. Specifically, the output includes set-points for switching shunts, transformer taps, and voltage magnitudes at the regulated buses. The primary goal is to maximize the dynamic reactive power reserve of the system, by minimizing the reactive power supplied by synchronous generators. As the size of the MP-ORPD problem increases significantly with increasing number of contingencies and time periods, efficiency is crucial for practical applications. In this paper, a decomposition technique based on consensus and alternating optimization, where integer variable targets are obtained via MILP, is used to partition the MP-ORPD problem into a set of subproblems, which can be solved in parallel to reduce the computation time. The proposed MP-ORPD problem and its solution algorithm are integrated into the EPRI-VCA software. The results of various power networks of large electric utilities in the Eastern interconnection demonstrate the effectiveness of the proposed algorithm in providing preventive control schedules. [ABSTRACT FROM AUTHOR]

A Hybrid AC/DC microgrid (MG) can integrate distributed generation sources and distributed loads on the AC and DC side of the MG by eliminating many unnecessary power conversion devices, which is more flexible and efficient. However, to achieve reliable and economic operation of a hybrid AC/DC MG is challenging due to its complex structure. In this paper, a novel distributed event-triggered hierarchical control strategy is proposed to improve the economic operation of a hybrid AC/DC MG. For the primary control, distributed local controls of AC DGs, DC DGs, and interlinking converters (ICs) are realized by adopting the droop control method. For the secondary control, the distributed economic dispatch, distributed average bus voltage discovery, and distributed proportional power-sharing algorithms are first proposed; then, control objectives of voltage and frequency restoration and economic operation of the hybrid AC/DC MG are realized based upon the developed algorithms. Furthermore, the distributed secondary control is built upon an event-triggered mechanism developed in this paper, which can reduce the communication burden. The simulation results demonstrate the effectiveness of the proposed control strategy. [ABSTRACT FROM AUTHOR]

In order to achieve the purpose of extending the speed range and reducing power electronics devices for the permanent-magnet linear motor drive system, a half-centralized open-end winding (OEW) topology is studied for rail transit applications in this paper. In this topology, compared with the traditional OEW topology, the number of voltage-source-inverters (VSIs) can be reduced from four to three to drive two OEW movers and all these VSIs share a common dc bus voltage. In order to improve the steady-state performances, a four-vector phase model predictive voltage control (FV-PMPVC) is proposed in this paper. Due to the spatial distribution of phase voltage vector (PVV), an orthometric synthesis principle (OSP) is proposed to calculated the duration time for the vector synthesis, which reduces the computation burden and enhances the robustness. Comparing the existing control method, FV-PMPVC can get similar dynamic performances but better steady-state performances. Additionally, the half-centralized topology using FV-PMPVC can have same speed range while less VSIs are required. The effectiveness of FV-PMPVC is verified by experimental results. [ABSTRACT FROM AUTHOR]

State-of-charge (SoC) imbalance and bus voltage deviation are two of the main problems in autonomous dc microgrids. Based on this concern, this paper presents an improved dual-quadrant SoC weighted control strategy and a distributed optimization control method to achieve SoC balance, ensuring accurate power-sharing and bus voltage recovery. Firstly, this paper couples the injected/released power with the current SoC and observed average SoC value to weight the droop coefficient, which is based on the charge/discharge mode for the energy storage system. Then a secondary controller is designed based on distributed optimal control to eliminate the bus voltage deviation caused by the line impedance difference. The proposed optimal control method optimizes the average bus voltage to the nominal value and achieve accurate power-sharing by constructing the correlated variables and voltage independent intermediate variables exchanged among bulk energy storage units (ESUs). Since the voltage observer cannot accurately observe the true average bus voltage under the communication delay, the proposed distributed optimal control method without the voltage observer can ensure that the average bus voltage is optimized to the nominal value, thus improving the robustness of the control system. Finally, the correctness and effectiveness of the proposed method are verified in Simulink/MATLAB. [ABSTRACT FROM AUTHOR]

The paper addresses a real-time optimization-based reference calculation integrated with a control structure for Modular Multilevel Converters (MMC) operating under normal and constrained situations (where it has reached current and/or voltage limitations, as it may occur during system faults). Firstly, a nonlinear optimization problem has been developed in which it prioritizes to satisfy the AC grid current set-points imposed by the transmission System Operator (TSO). The constrained nonlinear optimization problem is formulated based on the steady-state model of the MMC, whereby the prioritization is achieved through distinct weights defined in the Objective Function’s (OF) terms. The resultant optimization problem, however, is highly nonlinear requiring high computation burden to be solved in real-time. To cope with this issue, this paper applies a Linear Time-Varying (LTV) approximation, which permits to represent the nonlinear dynamics of the system as constant parameters, while a Linear Time-Invariant (LTI) system is used to formulate the optimization constraints. The converter’s current references are determined in real-time by solving a constrained linearized optimization problem at each control time step, which considers the TSO’s demands, the current MMC operating point and its physical limitations. Theoretical analyses comparing the responses of the linear and nonlinear optimization problems are performed to validate the accuracy of the LTV approximation. Finally, the linearized-optimization problem is integrated with the MMC controllers, evaluated under different AC and DC network conditions and compared with conventional control strategies, where it is shown that the presented method can be potentially employed to obtain the MMC current references for distinct network scenarios. [ABSTRACT FROM AUTHOR]

This paper presents extensive verification, sensitivity, and application studies for an online substation grounding grid condition monitoring method proposed in a companion paper. The studies are conducted using a realistic substation grounding grid and associated feeder configurations commonly encountered in North America. The verification studies confirm that the proposed method is able to estimate the substation grounding impedances with acceptable accuracy. Main factors impacting measurement accuracy are identified and quantified through sensitivity studies. The findings lead to a guide for the implementation and operation of the proposed method. An application case is presented to demonstrate how the gradual deterioration of substation grounding grid can be monitored using the proposed method. [ABSTRACT FROM AUTHOR]

In this paper, a reliable methodology is proposed in order to implement and validate a Model Predictive Control (MPC) scheme on an actual Voltage Source Converter (VSC) integrated in a scale-down multi-terminal DC grid. The objective of the investigated MPC controller is to enable AC frequency support among two asynchronous AC areas through a High Voltage Direct Current (HVDC) grid, while considering physical constraints, such as maximum and minimum DC voltage. A systematic and accurate implementation strategy is proposed, based mainly on the Hardware In the Loop (HIL) and Power Hardware In the Loop (PHIL), leading to the real-life testing on VSC, controlled by a classical microcontroller. The technical problems during the implementation process, as well as the proposed solutions, are described in detail through this paper. This procedure is deemed valuable to bridge the gap between offline simulation and the actual implementation of such advanced control scheme on experimental test rig. [ABSTRACT FROM AUTHOR]

This paper proposes a novel hybrid AC/DC microgrid architecture incorporating a central energy storage system (ESS) for both the AC and the DC sub-grids. To ensure effective operation of the proposed hybrid AC/DC microgrid architecture, a coordinated control strategy between the central ESS and the inter-linking converter (ILC) is proposed in the paper. The proposed central ESS provides voltage and frequency control to the AC sub-grid by measuring voltage and frequency at the point of common coupling (PCC) of the AC sub-grid, while providing DC voltage support to the DC sub-grid by measuring DC sub-grid’s PCC voltage. Furthermore, per-unit frequency and the DC sub-grid PCC voltage are utilized to transfer power between the two sub-grids via the ILC. Therefore, two control strategies are coordinating with each other and maintain stable operation. The central ESS eliminates the use of multiple ILCs and complex control schemes for charge and discharge control to maintain same state of charge levels at each ESS. Effectiveness of the proposed coordinated controller is verified by applying various load disturbances, faults, and under different modes of operation. [ABSTRACT FROM AUTHOR]

The neutral grounding method is one of the crucial technologies used to ensure the safe and stable operation of distribution networks. With the development of power electronics-based devices, the application of highly controllable inverters to grounding systems has become a new research direction. In this review paper, based on the summary and analysis for the research status, the flexible grounding system is systematically classified according to its control strategy and structure. And then, the following core technologies are summarized: faulted line selection, current component detection, high-resistance ground identification, ground parameter measurement, neutral point voltage control, and fault location. Subsequently, deficiencies of flexible grounding systems are summarized from the following four perspectives: reliability, accuracy, speed, and stability. Finally, some discussions and recommendations for future development and research direction are presented. Especially, the reliability-enhanced hybrid grounding system that combines active inverters and low resistance for high-resistance ground faults is recommended. This paper provides a systematic literature review of the crucial technologies for flexible grounding systems and can be used as a technical reference for future research. [ABSTRACT FROM AUTHOR]

This paper analyzes the unsymmetrical operation of the dc/dc MMC caused by parametric uncertainty. The unsymmetrical operation is referred to as the condition in which parameters involved in ac power generation are not equal in the phase-legs of the converter. Because existing models in the literature cannot exhibit the unsymmetrical operation of the dc/dc MMC, new detailed and simplified steady-state models are developed in this paper. In the developed models, the connection between the operation of different phase-legs shows itself when the dc-link impedance is considered. Using the developed models, the parameters that can force the converter to operate in unsymmetrical conditions are identified, and the maximum variation that the converter can tolerate is found. It is shown that even a small parameter variation leads to the leakage of the ac circulating current into the dc-link, which is not acceptable. By conducting various case studies, the impacts of the dc-link length, the transmitted power, and the conversion ratio on the unsymmetrical operation of the dc/dc MMC are characterized. The results showed that the converter would be more sensitive to the parameter variation as these parameters increase. Comparative analysis and simulation results confirm the validity and effectiveness of the presented models and analysis method. [ABSTRACT FROM AUTHOR]

The paper addresses an improved inner current reference calculation to be employed in the control of modular multilevel converters operating during either balanced or unbalanced conditions. The suggested reference calculation is derived based on the AC and DC additive and differential voltage components applied to the upper and lower arms of the converter. In addition, the impacts caused not only by the AC network’s impedances but also by the MMC’s arm impedances are also considered during the derivation of the AC additive current reference expressions. Another issue discussed in this article regards that singular voltage conditions, where the positive-sequence component is equal to the negative one, may occur not only in the AC network but also internally (within the converter’s applied voltages). Several different inner current reference calculation methods are compared and their applicability during the former fault conditions is analyzed. The paper presents a detailed formulation of the inner current reference calculation and applies it to different unbalanced AC grid faults where it is shown that the presented approach can be potentially used to maintain the internal energy of the converter balanced during normal and fault conditions. [ABSTRACT FROM AUTHOR]

This paper addresses the interactions among the control loops of voltage-sourced converters (VSCs) embedded in high-voltage direct current (HVDC) systems and the impact of these interactions on the performance of individual control loops. Furthermore, this paper proposes a method to design the individual control loops, rather than the interconnected control system, such that the overall system stability is ensured in the presence of interactions. This paper addresses three aspects of the impact of control loop interactions on the overall control system of the VSC including stability, transient response, and steady-state response. To illustrate the impact of interactions on the VSC small-signal stability, stability regions of the interconnected control loops are obtained and compared against those of the various individual control loops. Then, a novel formulation of the VSC stability criterion is presented, and the small-gain theorem is utilized to determine a range of stabilizing gains for the interconnected control system. Moreover, new indices using the infinity norm are introduced to evaluate the impact of interactions on the transient response of the VSC. Finally, the DC gain of a certain set of transfer functions is used to assess the impact of control loops interactions on the set-point tracking capability of the VSC. The introduced indices along with time-domain simulations show that the transient response of the d-axis control loops is not impacted by the interactions, whereas that of the q-axis control loops is significantly impacted by the interactions. The set-point tracking capability is proved to be independent of interactions. [ABSTRACT FROM AUTHOR]

While much attention was given in the literature to improve the fault ride through (FRT) capability of a doubly-fed induction generator (DFIG)-based wind energy conversion system (WECS) during various faults at the grid side, not much attention was given to investigate and improve the performance of the DFIG-WECS under ferroresonance conditions. This paper investigates the impact of ferroresonance on the overall performance of a DFIG-WECS. The paper also presents a new technique to improve the high voltage ride through capability of the investigated system under such condition. The proposed technique relies on incorporating a superconducting coil within the dc-link of the DFIG grid-side and rotor-side converters. Energy exchange between the coil and the system is controlled through regulating the duty cycle of the dc-chopper interfacing the coil with the dc-link. In this regard, a simple but yet effective proportional-integral (PI) controller is employed to regulate the dc-chopper duty cycle. Parameters of the PI controller are optimized using elephant herding optimization algorithm. Simulation results verify the effectiveness of the proposed controller in improving the overall performance of a DFIG-WECS during ferroresonance events. [ABSTRACT FROM AUTHOR]

In this paper, a new modulation strategy based on the carrier-based switching strategy for the non-square direct matrix converters (MC) is proposed to control the active power of distributed generation (DG) units. In this strategy, the active power of DGs is controlled by the central input current control of the non-square direct MC independent from the voltage and frequency. Conventionally, each DG has a converter, and for supplying a load with N number of DGs, N number of converters are needed and each converter has its own modulation switching and control strategy to control the power output of each DG. Needless to say, in a microgrid with N number of DGs, the control strategy of each converter has more complex structure than that of a microgrid with one converter, and surely the former strategy entails more volume and price. Using the proposed converter in this paper, it is possible to supply a load with N number of DGs through one converter. Also, the power outputs of all DGs are controlled by a central control strategy. The proposed central control strategy is described and simulated for a typical microgrid. Experimental and simulation results validate the effectiveness of the proposed converter and the proposed strategy. The results demonstrate the applicability and efficiency of the system and verify the theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper presents a method for controlling the voltage of inverter-based Microgrids by proposing a new scale-free distributed cooperative controller. The main contribution of this paper is that the proposed distributed cooperative controller is scale-free where is independent of any information about the communication system and the number of distributed generators, as such it works for any Microgrids with any size. Moreover, the communication network is modeled by a general time-varying graph which enhances the resilience of the proposed protocol against communication link failure, data packet loss, and arbitrarily fast plug and play operation in the presence of arbitrarily finite communication delays as the protocol does not require the knowledge of the upper bound on the delay. The stability analysis of the proposed protocol is provided. The proposed method is simulated on the CIGRE medium voltage Microgrid test system. The simulation results demonstrate the feasibility of the proposed scale-free distributed nonlinear protocol for regulating voltage of Microgrids in the presence of communication failures, data packet loss, noise, and degradation. [ABSTRACT FROM AUTHOR]

The stability of power systems can largely limit the power transfer capability limit of transmission lines. The PV generator control is different from synchronous generator control. The impact of PV generator dynamics on the power transfer limit constrained by stability is not well explored in the literature. This paper focuses on improving the stability constrained power transfer capability limit of transmission lines emanating from PV generators. The PV generator is provided with dc link voltage and reactive power control and is equipped with low voltage ride through capability, voltage and frequency support functionalities. In this paper, Lyapunov function analysis based adaptive tuning laws are proposed for PV control parameters to improve the power transfer capability limit (constrained by stability) of transmission lines connecting PV generators to grid. The tuning laws are proposed for Phase Locked Loop (PLL), outer and inner control loop parameters. The proposed tuning laws have inherent robustness towards faults, changes in solar irradiation, changes in grid topology, network impedances, generation and loads in the system. The effectiveness of the proposed method is validated on a Single PV-Synchronous Machine system, modified IEEE-39 and IEEE-118 bus system. The performance of the proposed method is investigated considering various disturbances such as symmetrical and asymmetrical faults on transmission line, switching of a transmission line and change in solar irradiation of PV. Comparison with existing method shows that the proposed tuning method can achieve higher power transfer capability limit considering stability. [ABSTRACT FROM AUTHOR]

A phase-locked loop (PLL) is commonly used in grid-connected power converter for synchronization. A single input single output (SISO) linear model of PLL with the phase angle of the point of common coupling (PCC) voltage as input and the estimated phase angle as the output is generally used in the PLL analysis and design. However, an undesirable coupling between the magnitude and phase of the input voltage is present when a filtering stage is incorporated before the control loop, which a SISO model cannot capture, and could result in a significant disturbance in the PLL estimated phase during grid faults. This paper proposes a generalized multi-input multi-output (MIMO) linear model that captures the complete PLL dynamics during symmetrical faults for a PLL equipped with any prefilter. Furthermore, a compensation method that decouples the magnitude dynamics of the input voltage from the phase dynamics is proposed in this paper. The proposed compensation improves the PLL's phase tracking performance by ensuring that the prefiltered PLL acts only on the PCC voltage phase changes. A vital application of the proposed compensation method for PLL is during a grid fault case, wherein the converters are expected to contribute to the fault current, which requires an accurate measurement of the PCC voltage phase. The compensation method's effectiveness is demonstrated using power hardware in the loop simulation of a hardware voltage source converter interfaced to a distribution system simulated in real-time. [ABSTRACT FROM AUTHOR]

The paper introduces the concept of complex frequency. The imaginary part of the complex frequency is the variation with respect of a synchronous reference of the local bus frequency as commonly defined in power system studies. The real part is defined based on the variation of the voltage magnitude. The latter term is crucial for the correct interpretation and analysis of the variation of the frequency at each bus of the network. The paper also develops a set of differential equations that describe the link between complex powers and complex frequencies at network buses in transient conditions. No simplifications are assumed except for the usual approximations of the models utilized for the transient stability analysis of power systems. A variety of analytical and numerical examples show the applications and potentials of the proposed concept. [ABSTRACT FROM AUTHOR]

This paper establishes an instantaneous voltage model to illustrate the dynamic characteristics of grid voltage in electromagnetic time scale affected by power-electronic interfaced voltage regulatory devices with two typical categories of control systems, i.e., power-current cascading control and power synchronization control, exemplified by the STATCOM and virtual synchronous condenser (VSCON) respectively. In this paper, a linearized instantaneous voltage model is firstly established to analyze the impact paths of control loops in the STATCOM and VSCON. Based on the model, the dynamic process of grid voltage is divided into three stages. Various factors on the dynamic process of grid voltage are analyzed, especially cascading control loops prior to the functioning of AC voltage control. Moreover, stiffness characteristic is proposed to evaluate the effects of power electronic interfaced voltage regulatory devices with different control structures. In addition, the effectiveness of the stiffness compensation based on the VSCON is validated by the study cases. [ABSTRACT FROM AUTHOR]

In this paper, it is identified that unstable weak grid connection of voltage source inverters (VSIs) is dominantly caused by the current control. In particular, it is found the proportional gain $ k_p$ of conventional PI controller cannot balance the grid voltage impact and damping capability especially when a very weak grid with short circuit ratio (SCR) $ < $ 1.3 is connected. This issue is solved in this paper by simply restructuring the PI controller as an IP controller for current control. This IP controller will not change the tuning method of current control and make this VSI indeed connect to a very weak grid with rated power injection. [ABSTRACT FROM AUTHOR]

The short-circuit response of inverter-interfaced distributed generators (IIDGs) is not adequately represented in many conventional protection studies. This paper presents an in-depth analysis of IIDG behavior during grid faults and proposes a more accurate reduced-order parameterized short-circuit current (RPSC) model of inverters. Typical inverter components are thoroughly investigated to identify those that play dominant roles during faults. The paper shows that the current limiter is the dominant factor for the steady-state fault-current of inverter; while the inverter filter along with the severity of the voltage disturbance largely determine the initial transient spike of inverter fault current. The proposed model is low-order and can be used in large scale simulations. The parameters of the proposed RPSC model can be extracted from laboratory experiments without requiring proprietary manufacturer information. The proposed fault-current model is analogous to the well-known synchronous machine model that segregates the inverter fault current into subtransient, transient, and steady-state fault currents. Experimental and simulation tests are presented to validate the model. [ABSTRACT FROM AUTHOR]

Autonomous power systems with a single power station and a high-voltage (HV) network may be susceptible to overvoltage instability, especially during light-load conditions. Moreover, in low inertia systems, considerable frequency excursions may be observed after disturbances. To deal with voltage and frequency stability problems in such isolated power systems, several measures should be taken, such as rules for adequate automatic voltage control of the synchronous generators and load-tap-changers (LTCs), and/or adequate design of actions applied during emergency system conditions such as reactors switching, and redesigning underfrequency load shedding taking into account overvoltage problems. The effectiveness of the proposed countermeasures against overvoltage instability in autonomous power systems is illustrated in this paper. In 2016, the autonomous power system of the Greek island of Rhodes experienced similar voltage/frequency problems leading to a blackout. This event has been accurately reconstructed in this paper. The application of the suggested countermeasures during the simulation of the 2016 blackout event in Rhodes, further highlighted the effectiveness of these measures, providing a guideline for similar cases. [ABSTRACT FROM AUTHOR]

Droop control is a viable method for the operation of island DC microgrids in a decentralized architecture. This paper presents a mixed-integer conic optimization formulation for the design of generator droop control, comprising the parameters of a piecewise linear droop curve. The mixed-integer formulation originates from a stochastic optimization framework that considers several operating scenarios for finding the optimal design. The convexity of the mixed-integer problem continuous relaxation gives global optimality guarantees for the design problem. The paper presents computational results using a tight polyhedral approximation of the conic program, leading to a mixed-integer linear programming (MILP) problem that is solved using a state-of-the-art commercial solver. The results from the proposed approach are contrasted with both a classic linear droop control design and a recent piecewise linear formulation. The Monte-Carlo simulation results quantify the extent to which the MILP solution is superior in reducing voltage violations and power loss, and the degree to which the loss is close to that from a conic optimal power flow solution. [ABSTRACT FROM AUTHOR]

Aiming at the low-frequency oscillation (LFO) phenomenon in high-speed railways, this paper proposes a feedback linearized virtual inertia control (VIC) strategy of the traction converter based on a sliding mode observer (SMO) to improve the robustness of the system and suppress the occurrence of LFO. First, to optimize the total harmonic distortion of the traction grid-side current, the inner loop controller is designed as the feedback linearization control. Then, the voltage outer loop is designed as a combination of the VIC designed in this paper and SMO, which enhances the system inertia and reduces the impact of external interference on the system, while reducing the controller's demand for electrical power on the DC-side. Furthermore, a small-signal model is established to analyze the stability of the single-phase vehicle-grid system under the proposed control. The influence of the control parameters on stability is discussed in detail. Finally, the comparison of software simulation and hardware-in-the-loop experimental results between traditional PI control, feedback linearization control, feedback+SMO, feedback+VIC and the proposed control method shows that the proposed control has better dynamic and static characteristics, and can effectively inhibit the occurrence of LFO. [ABSTRACT FROM AUTHOR]

Battery energy storage system (BESS) plays an important role in solving problems in which the intermittency has to be considered while operating distribution network (DN) penetrated with renewable energy. Aiming at this problem, this paper proposes a global centralized dispatch model that applies BESS technology to DN with renewable energy source (RES). The method proposed in this paper aims to minimize the power purchase cost considering network active loss cost as well as voltage deviation penalty cost. Later, second-order cone programming (SOCP) method as well as big M method are applied to make the problem tractable. Last, the method illustrated in this paper is applied and validated on a modified IEEE 33-bus benchmark system to verify the effectiveness of the proposed scheduling model. [ABSTRACT FROM AUTHOR]