Search

Breakdown in dielectrics, the mechanism of which is still not yet fully revealed, exhibits very complicated test phenomena and characteristics. The breakdown voltage of a dielectric is believed to be related not only to the dielectric properties but also to the waveform of the applied voltage. For most dielectrics, the impulse breakdown voltage decreases with increasing wavefront time. However, we found for oil-impregnated paper (OIP) used in power transformers, increasing wavefront time in lightning impulses (at microsecond timescales) may lead to a significant increase in breakdown voltage. In contrast, the variation in the wavetail time produces very little effect on breakdown voltage. Combined with our previous test results on the space charge distributions in OIP, we tried to provide two explanations regarding this interesting phenomenon: First, the wavefront time of the applied impulse voltage affects the movement process of the positive particles in the oil-filled micro cavities in OIP, which is strongly related to the local electric field in the oil filled micro cavities and the breakdown voltage of the OIP. Moreover, the wavefront time is closely related to the trapping and detrapping process of the dielectrics. Therefore the effects of the traps in dielectric on the breakdown characteristics are different when the wavefront time varies. [ABSTRACT FROM AUTHOR]

As striking lightning impulse waveforms in power transformers are quite different from the standard lightning impulse waveform (SLIW) used in the withstand voltage tests, it is essential to identify the breakdown characteristics of oil-impregnated paper (OIP) under non-SLIW and to quantitatively compare them with those under SLIW. On that basis, the impulse insulation levels of power transformers can be rationally determined and then the insulation specifications can be evaluated to maintain high equipment reliability. In this paper, with damped alternating oscillation waveform as a representative basis, the breakdown characteristics of oil-impregnated paper were experimentally obtained by changing the frequency and damping rate of the applied voltage. All experiments were conducted using a column-column electrode model. In addition to the 50% breakdown voltages (U50), Minimum breakdown voltage Umin and V-t characteristics under different circumstances, the influence of various parameters on breakdown characteristics and the possible reasons were discussed. After comparing waveforms and corresponding results, the specific relationship between waveform parameters and U50 were expressed as a single equation. As a result, the breakdown voltage was 1.106 to 1.435 times higher than that under SLIW depending on frequency and damping rate. The steepness of the wave peak and the duration of high voltage around wave crests are considered to be two important factors affecting the breakdown voltage. An effective way was proposed to predict U50 of oil-impregnated paper as a reference for insulation specifications irrespective of wave shape. These results support the rationalization of insulation for actual lightning impulse waveforms in the power transformers. [ABSTRACT FROM AUTHOR]

Oil-paper insulation, as a major insulation mode used in power transformers, is continuously and unavoidably subjected to repeated lightning impulses, which may bring potential risk to the insulation system. Therefore, in this work, accumulative effect of repeated lightning impulses and its damage mechanism in oil-impregnated paper (OIP) are investigated. Firstly a repetitive impulse accumulating test platform was set up, and tests were performed to confirm the existence of accumulative effect of repeated lightning impulses. Then atomic force microscope observation and frequency domain spectroscopy were carried out on OIP samples with different times of lightning impulses, based on which the influence of lightning impulses accumulative effect on surface morphology and dielectric properties of OIP was investigated. The results indicate that repeated lightning impulses produce accumulative damage to the OIP and hence lead to the morphology change and generation of translucent gelatinous substance on the sample surface. Both the surface roughness and dielectric parameters increase with the accumulating of repeated lightning impulses, which can be attributed to the effects of polar products, fiber deformation and the translucent gelatinous substance together. At last, the possible mechanism of the accumulative effect was discussed and relevant tests were carried out to verify the speculation. [ABSTRACT FROM PUBLISHER]

The non-standard lightning impulse waveforms (N-SLIWs) including oscillating lightning impulses, very fast transient voltages (VFTOs) and steep waveforms in the power system gravely endanger the inner insulation of power transformer. To prevent insulation failure and provide guidance for robust transformer design, in this paper, two typical insulation models of oil-immersed transformer were established and their breakdown characteristics under N-SLIWs were investigated. The research mainly focused on the influence of front time and oscillation frequency of N-SLIWs on the breakdown characteristics. The experimental results showed that the breakdown voltage increased with the decrease of front time. For low frequency-oscillating lightning impulse waveforms (LF-OLIWs), breakdown voltage increased with the increase of oscillation frequency and was up to 30% higher than that under standard lightning impulse waveform (SLIW). For VFTOs, with the increase of frequency, breakdown voltages presented a law of inverted "U" type. Insulation model could withstand the highest value of VFTO when the oscillation frequency was around 2.4 MHz. But when the frequency was as high as 9 MHz, breakdown voltage was close to that under SLIW. A very high frequency oscillation was the main reason for the reduction of breakdown voltage as its steepness dV/dt assisted the effective transmission of the sphere?s potential to the head of the streamer channel. [ABSTRACT FROM AUTHOR]

Repeated impulses have long been considered to affect the insulation properties of electrical equipment. This interesting but rarely studied phenomenon may pose great risks to the reliable operation of power equipment. Therefore, in this work, we focus on the accumulative effect of repeated lightning impulses on the oil-impregnated paper (OIP) used in power transformers. Specifically, we study the effect of space charge on the accumulative characteristics of OIP. A repetitive impulse accumulating test platform was set up, and the tests were conducted to obtain the accumulative characteristics of OIP under repeated lightning impulses. The accumulative characteristics of OIP with various interval time were experimentally identified to study the influence of interval time on the accumulative effect. Then, space charge in OIP samples were investigated using the pulsed electro-acoustic technique. Charge behavior in OIP was analyzed under different conditions, i.e., changing the applied times, amplitude and interval time of the applied lightning impulses. Charge injection and transport occurred during lightning impulse accumulation. The increased application of lightning impulses, high applied voltage, and short interval time contributed to the accumulation and transport of space charges. At last, the possible mechanisms of the accumulative effect are discussed in this article based on the experimental results. [ABSTRACT FROM AUTHOR]

On-line monitoring of insulation systems in power components such as power transformer bushings has significant value for their reliability. Dielectric spectroscopy is known as a powerful tool in condition assessment of power components? solid insulation. However, it is difficult to apply it on-line. Therefore, a new approach of intended use for on-line diagnosis of oil-impregnated paper, as a major insulation component of power transformers and bushings, is presented. In this technique, natural transients such as lightning and switching impulses are used as stimuli for on-line dielectric response measurements. The wide frequency range of these transients is their advantage as stimuli for dielectric spectroscopy. The influence of moisture content and temperature on the dielectric response of oil-impregnated paper has been investigated for performance evaluation of the proposed technique. It is shown that this technique can track the changes caused by moisture content and temperature in the dielectric response of oil-impregnated paper. The results of both low and high voltage study cases have been verified by comparison with Frequency Domain Spectroscopy (FDS). According to the well-matched results with FDS, the proposed technique can offer a valuable approach for frequent monitoring of dielectric properties of oil-impregnated paper insulated systems such as those commonly encountered in power transformer bushings. However, the validity range of the results depends on the bandwidth of the applied transients and other discussed measurement considerations. [ABSTRACT FROM AUTHOR]

In this paper, the initial stage and the return stroke current waveform parameters of rocket-triggered lightning flashes to the ground and to the distribution line have been analyzed. The results show that the average current, the charge transferred and the action integral associated with the Initial Stage with return strokes are greater than the corresponding values without return strokes. For the initial stage, the presence of the distribution line greatly reduces the maximum current, average current, charge transfer, and action integral by a factor of 0.35, 0.42, 0.51, and 0.19, respectively. For the return stroke, the presence of the distribution line has little effect on the other parameters except for a 2.4-fold increase in the 10-90% risetime. The presence of the distribution line affects the initial stage parameters more significantly than the return stroke parameters, probably because the lightning channel equivalent impedance of the initial stage is much smaller than that of the return stroke. The lightning channel equivalent impedance of the initial stage estimated in this paper is about 145 ohms and the estimated lightning channel equivalent impedance for the return stroke is greater than 2000 ohms. [ABSTRACT FROM AUTHOR]

Multiple strokes are the main factors affecting the safe and stable operation of power equipment. As the core lightning protection equipment, arresters are also frequently thermally collapsed due to multiple strokes. This paper investigates thermal effects of polymer-housed metal-oxide surge arrester (PMOSA) under multiple strokes. The comparative experiments of PMOSA lightning impulse are carried out through multiple strokes of experiment platform, including continuous lightning stroke and multiple strokes. Furthermore, the temperature distribution of the housing surface is obtained by infrared imager for thermal effect analysis. Subsequently, some typical DC parameters are tested to explore the association of impulse aging and thermal effects of the arrester under multiple strokes. Finally, a thermal-electric coupling model (TECM) is constructed to investigate the influence of some factors on the temperature of PMOSA from the perspective of materials and structure. The research in this paper can provide a theory reference and brief data support for improving the heat dissipation performance of arresters under multiple strokes based on structural optimization design and material modification. [ABSTRACT FROM AUTHOR]

Single horizontal and vertical grounding electrodes are often used for an earth connection of the lightning protection system. However, there are many practical situations when such electrodes have to be enhanced for better efficiency and replaced by multiple horizontal, vertical and/or inclined electrodes. This paper presents a systematic approach to evaluating and comparing the lightning performance of such grounding arrangements based on simple formulas. The contributions of this paper are: It is shown that impulse impedance Z may be derived from known formulas for low-frequency grounding resistance R; a new definition of effective length is introduced that allows for such a derivation; a collection of accurate formulas for R of all considered grounding electrode arrangements is presented; and a new concept of “effective volume” is described that enables a simple procedure to increase electrodes’ effective length. The new formulas for R, Z, and effective length of the different electrode arrangements allow an analysis that might help search for a choice of cost-effective configuration and dimensions of the grounding systems in the early design stage. [ABSTRACT FROM AUTHOR]

This paper presents the three-phase impulse overvoltage measured at the terminal of a 10 kV distribution line when the impulse current was injected into the phase conductor of the distribution line. The overvoltage observation station was installed at the terminal of the line to record the three-phase overvoltage waveforms. It is shown that the struck phase overvoltage consists of three components including the negative pulse, the stage of residual voltage maintenance and the overshoot oscillation part. The observed negative peak values of the struck phase overvoltage range from −85.4 kV to −96.0 kV in three different injected impulse levels at 90,120,150 kV charging voltage. The duration of residual voltage depends on the duration time of injected current. Furthermore, there is a strong positive relationship between the oscillation amplitude of the struck phase overvoltage and the injected current amplitude. The peak amplitudes of three-phase overvoltage always have the following magnitude relationship: struck phase C > induced phase B > induced phase A. The voltage coupling coefficients of induced phases will not exceed 0.4. The test method proposed in this paper will be helpful to the research on the lightning overvoltage response characteristics of the distribution line and the protection analysis of arresters. [ABSTRACT FROM AUTHOR]

This paper discusses the back-flashover (BFO) phenomena in a high-voltage (HV) vertical double-circuit transmission line by means of numerical simulations. The single- and multiphase BFOs are analyzed considering 24 cases of AC-voltage angles and nonlinear characteristic of flashovers, taking advantage of the circuit analysis method in time domain. The models used in circuit analysis are the TEM-delay model, which can take into account the non-TEM characteristics of tower and line, and the conventional models. Prior to the BFO analysis, the characteristics of circuit models are compared and discussed with the numerical electromagnetic analysis results. In BFO analysis, it is clarified that the occurrence probability of the multiphase BFO is heavily depending on the bias AC-voltages. The relation of measured BFO phases and AC-voltages are well explained by the TEM-delay model with the valid lightning current magnitude. The conventional circuit models could have underestimated the occurrence of BFOs in HV transmission lines. The analysis and discussions shown in this paper can be utilized for advanced evaluation of lightning performance of transmission lines that considers the seriousness of lightning accidents. [ABSTRACT FROM AUTHOR]

It is well known that for high voltage transmission lines in the range of 245 kV–525 kV, particularly in regions of high ground resistivity, lightning back flashover problems could be a major concern. Line arresters have been used successfully to address the problem. Underbuilt ground wires have been proposed as a viable alternative. The present paper shows that the full potential of additional ground wires could be achieved by optimizing their position on the tower. Such optimization often results in a preferred position at the level, or higher than the attachment height of the lower phase conductors; therefore the designation Embedded Ground Conductor. An essential requirement is that such positioning does not infringe in any way on the dielectric integrity of the electrical clearances and, under the influence of induced charge, does not become a source of positive streamers that may lead to additional radio or audible noise. It is found that a streamer- inhibited conductor, when properly placed, fully satisfies the above requirements. It is determined that for 245 kV, 345 kV and 420 kV lines, a streamer-inhibited embedded conductor could improve the back flashover rate by a factor of 10 or more [ABSTRACT FROM AUTHOR]

Most of the literatures dealing with time domain simulation of grounding system response to lightning surges use an electrostatic approach. In this approach frequency dependence of soil electrical parameters and plane-wave propagation constant are not included. In this paper, based on Hybrid Electromagnetic Method and simplification of it, a new method is developed to include frequency dependent parameters of soil in time domain simulation. Since only one convolution is used, the simulation time is significantly reduced. The consistency of the developed formulation while the plane-wave propagation constant is ignored is investigated through comparisons with experimental results and precise frequency domain approaches. Simulations results show ignoring both effects simultaneously can lead to high levels of error (140%), whereas the error significantly reduces when frequency dependence of soil parameters is considered. The developed model exhibits errors of about 2% to 25% compared to the results of models that take into account both effects. However, simulation results showed all these errors to be conservative. Due to neglecting propagation constant, the model is more suitable for lightning studies of grounding system with short length. [ABSTRACT FROM AUTHOR]

Direct lightning poses a serious threat to the safety of power systems. In recent years, the lightning fractal model, which can reflect the fractal characteristics and randomness of lightning leaders, has been gradually applied to direct lightning protection for substations, transmission lines, etc. However, since few studies have linked simulations with experiments, the reliability of the lightning fractal model in terms of attachment probability prediction lacks experimental verification. In this paper, a series of attachment tests are carried out under a rod-rod gap. The equivalence between simulation tests and natural lightning is discussed, and the influencing factors of the attachment results are investigated. The attachment probability is simulated and compared to the test value under each test configuration. The test results show that the fractal dimension of discharge channel is consistent with the observation results of natural lightning. Under different configurations, the test value of attachment probability basically conforms to the simulation value. In general, the dispersion of the test results is slightly greater than the simulation results, but the average probability differences are all within 10%. The test results strongly indicate that the lightning fractal model is of good reliability in the prediction of strike probability. [ABSTRACT FROM AUTHOR]

Fragility modeling and real-time risk assessment can be widely applied to evaluate and enhances the resilience of the power system to High-Impact and Low Probability events. In previous studies, fragility modeling generally targets extreme weather conditions other than thunderstorm. This paper proposes a fragility model to describe the relationship between the duration of a thunderstorm and the probability of lightning related trip-out. The duration of thunderstorms, which can usually be forecasted from the meteorological department, together with the fragility function expression can help a power company to predict the possibility of lightning related trip-out. Furthermore, this paper proposes a real-time risk assessment model that can dynamically adjust the risk value based on the update of the location, peak current, and subsequent stroke of real-time thunderstorm. A case study conducted on the lightning related trip-out data in Southwest China demonstrates that the average risk of transmission line trip-out in high risk group is about ten times that in low risk group. It clearly demonstrates that real-time risk assessment can efficiently distinguish the trip-out risks of different real-time thunderstorms. [ABSTRACT FROM AUTHOR]

The electric field uniformity imposes a significant effect on the breakdown mechanisms of dielectric liquids. In general, breakdown is dominated by streamer initiation under uniform field, while it is dominated by streamer propagation under non-uniform field. This paper presents a study on identifying and quantifying the transition field factor boundary, represented by the field enhancement factor ƒ, between the two dominating breakdown mechanisms. The methods for deducing the transition field factor boundary are introduced. The first method from our previous study was developed by measuring and processing both the streamer initiation and breakdown voltages. In this paper, a new method is developed by only processing the breakdown voltage data. Based on the breakdown results reproduced from the literature, the transition field factor boundaries are derived for the mineral oil under both positive and negative lightning impulses. It is found that the negative transition field factor boundary is lower than the positive one. A four-region model is proposed to describe the effect of impulse polarity on breakdown mechanisms of dielectric liquids and to interpret the transition of breakdown mechanisms with respect to the field uniformity. [ABSTRACT FROM AUTHOR]

This paper presented an assessment of lightning energy absorption by dedicated surge arresters (SADT), which are provided to protect the distribution transformers on 10kV overhead distribution lines (OHLs). A hybrid Partial Element Equivalent Circuit-Multi-conductor Transmission Line (PEEC-MTL) code was applied to evaluate lightning surges on SADT. This method has the capability of modeling both short and long wires in OHL systems and is verified numerically and experimentally. A Monte Carlo procedure was adopted to assess the fault rate (FR) of SADT. It is found that the direct lightning strokes to the phase wire are the primary threat to the SADT, compared with the strokes to the poles as well as indirect strokes to the ground or structure nearby. Several protection schemes are identified, and their performance is evaluated from the aspects of lightning protection and economic cost. The full shielding wire (SW) scheme performs the best, but with the most expensive protection cost. The lightning energy absorption by SADT can be suppressed significantly by installing extra SAs on the adjacent poles. The scheme of two or four extra SAs together with a partial SW can achieve a balanced performance of protection effect and economic cost for the OHL. The SW for a section of the OHL alone is not enough to the lightning protection for SADT. [ABSTRACT FROM AUTHOR]

Wind turbines (WTs) can beseriously damaged by lightning strikes and they can be struck by a significant number of flashes. This should be taken into account when the WT lightning protection system is designed. Moreover, WTs represent a path for the lightning current that can modify the well-known effects of the lightning discharge in terms of radiated electromagnetic fields, which are a source of damage and interference for nearby structures and systems. In this paper, a WT struck by a lightning discharge is analyzed with a full-wave modelling approach, taking into account the details of the WT and its interactions with the lightning channel. The effects of first and subsequent return strokes are analyzed as well as that of the rotation angle of the struck blade. Results show that the lightning current along the WT is mainly affected by the ground reflection and by the reflection between the struck blade and the channel. The computed electromagnetic fields show that, for subsequent return strokes, the presence of a WT almost doubles their magnitude with respect to a lightning striking the ground. Such enhancement is emphasized when the inclined struck blade is considered. [ABSTRACT FROM AUTHOR]

This paper reports the waveform characteristics and parameters of the overvoltage at the terminal of a 1.5 km 10 kV distribution line by direct triggered lightning. The three-phase overvoltage exhibited three kinds of waveforms, all including the initial rising process of the negative peak, the transition from negative peak to the positive peak or the residual voltage, and the subsequent oscillation process. It is observed that the negative peak value of the three-phase overvoltage is between −8.2 kV and −96.1 kV and the rise time of negative peak is between 3.2 μs and 31.7 μs, while the corresponding peak value of the return stroke current is between 3.3 kA and 32.9 kA. When the return stroke current is relatively small, the negative peak value of the direct struck phase overvoltage is twice or more than that of the indirect struck phase. When it is larger, the negative peak value of the indirect struck phase overvoltage is much closer to that of direct struck phase. There is good linear relation between the negative peak value of the indirect struck phase overvoltage and the peak value of the lightning return stroke current, with correlation coefficient being 0.98 and 0.90. [ABSTRACT FROM AUTHOR]

The power distribution system’s fault root cause classification is an important but challenging problem. Traditional classifiers fail to achieve high accuracy and good generalization performance due to data insufficiency. A large volume of unlabeled data is available, which can be utilized to improve classification performance. This paper proposes a novel classifier called Robust Semi-Supervised Prototypical Network (RSSPN) based on Prototypical Network architecture and semi-supervised learning to address this issue. The proposed method can mine information from unlabeled data to improve the generalization ability and classification accuracy. Furthermore, RSSPN adopts the idea of meta-learning to obtain the “few-shot learning” ability for identifying new fault classes using very few samples encountered during the operation and update online. Experiments have been conducted on a dataset consisting of 1152 labeled samples belonging to 12 different classes and 10000 unlabeled samples. The accuracy of the proposed method is significantly better than the traditional classifiers. [ABSTRACT FROM AUTHOR]

Lightning strikes in substations may result in extremely uneven ground potential distribution, which will threaten the safety and stability of equipment in substation. However, the main parameters for evaluating the performance of grounding grids are grounding resistance and impulse impedance, and little attention is paid to the distribution of the transient ground potential differences. In addition, when measuring the impulse impedance of a grounding grid, the length of the current leads should be very large, which requires a high-capacity impulse generator to suppress the influence of lead inductance on current waveform. In this paper, a test method is proposed for the transient characteristics of grounding grid with the current-return point located in the same grid. The feasibility of the method is illustrated by analyzing the ground impedance between the current injection point and the return point, longitudinal current of the grounding conductor, transient ground potential rise and transient ground potential difference. The effects of parameters such as soil resistivity, lightning waveform, size of the grounding grid, spacing and materials of the grid conductor are discussed to demonstrate that the method can be applied to most substations. Finally, the practicality of the method is verified by experiments in a 220 kVsubstation. [ABSTRACT FROM AUTHOR]

The accurate assessment of lightning-induced over-voltages is essential for proper insulation coordination studies. In this paper, a novel machine learning based Gaussian process regression model is developed for the prediction of lightning-induced over-voltages considering wide range of ground resistivity and permittivity. The lightning-induced over-voltages have been computed using two-dimensional finite-difference time-domain technique associated with Agrawal field to line coupling model. To account for the input space variability, seven predictor variables namely: resistivity, permittivity, return stroke velocity, distance from flashpoint, return stroke peak current, front-time, and height of an overhead line are considered to determine the response variable, that is, lightning-induced over-voltages. Accordingly, the training of the Gaussian process regression model is carried out using lightning-induced over-voltages obtained from two-dimensional finite-difference time-domain technique for both first and the subsequent strokes. The estimation accuracy of model is appraised using root mean squared error indicating that the exponential kernel function has the least error than other kernel types for describing the covariance. The predictive performance is evaluated by corroborating the predictions from the model against the random test cases generated from two-dimensional finite-difference time-domain technique. The predicted results showed a good agreement with those obtained from finite-difference time-domain technique. [ABSTRACT FROM AUTHOR]

Ground wires (GW) struck by lightning are often exposed to transient impulse voltages in the MV range. This results in intense negative streamer-type corona, causing a considerable increase in the effective wire capacitance and a corresponding reduction in its surge impedance. Such variables have a significant influence on the tower top potential and on the electromagnetic coupling between the ground wire and phase conductors. Presently there is considerable uncertainty regarding the impulse corona parameters to be used in back flashover calculations. In the present paper a new method is formulated for determination of GW impulse corona parameters. The new approach is compared with two existing methods and with available experimental results. It is found that the method usually used within the IEEE has little physical justification and is excessively conservative. It is also shown that such corona parameters significantly depend on the GW height above ground, which has been totally ignored in the CIGRE method. This and other unjustified simplifying assumptions explain the surprisingly large discrepancy between values of the negative impulse corona constant recommended by CIGRE and IEC. [ABSTRACT FROM AUTHOR]

This paper presents an assessment of lightning protection schemes for overhead lines from two aspects: protection performance and economic cost. Considering the random nature of lightning, the Monte-Carlo method with a heuristic technique is applied in the assessment. The one-dimensional finite-difference time-domain method is adopted to evaluate lightning overvoltages on insulators and lightning currents in surge arresters for failure assessment. The failure rate of an overhead line is addressed under both direct lightning and indirect lightning. A reduced set of design parameters are identified. It is found that the line insulation itself with a critical flashover overvoltage of less than 200 kV is not sufficient for lightning protection, especially against direct strokes. With other protection options, however, increasing the insulation level can greatly improve the protection performance. Installing surge arresters on every pole results in the best protection performance, but could be extremely expensive due to the replacement of failed surge arresters. The shielding wire provides moderate protection performance with a relatively low cost. The combination of the shielding wire and surge arresters provides much better performance under a wide range of soil conductivity with a moderate cost. It is worth mentioning that adopting high insulation strength for overhead lines in the new-line design could lead to significant cost savings for lightning protection. Guidelines for selecting design parameter values and protection schemes are provided, as well as a procedure for performance-cost evaluation. [ABSTRACT FROM AUTHOR]

Striated YBCO-coated conductor is a variant structure of the second-generation high-temperature superconducting (HTS) tapes. The ac loss is reduced owing to the YBCO layer of the striated YBCO tape is divided into filaments by laser scribing. Hence, it is promising for practical HTS electrical application, such as HTS transformer and cable. However, when the superconducting apparatuses are operated in the power grid, it will possibly experience the lightning impulse current in some extreme working condition. Thus, the performance of striated YBCO tapes suffering from exposure to lightning current is important to be studied. In this paper, a numerical model based on the electromagnetic–thermal coupling is built to analyze the lightning current performance of the striated YBCO tapes. The influence of structural changes on the thermal stability is discussed. The standard lightning current waveform is chosen, i.e., 8/20 μs. The simulated results show that cutting the copper edges of striated YBCO tapes will significantly degrade the lightning current withstand capacity. Instead, the degradation effect of grooves is not so obvious. [ABSTRACT FROM AUTHOR]

This paper presents the results of experimental characterization of creeping discharges propagating over pressboard immersed in insulating oils, under AC and standard lightning impulse voltages. For comparison purposes, synthetic ester, rape seeds oil (natural ester) and mineral oil were also investigated. Two experimental arrangements were used: (1) a point-to-plane electrodes system where the pressboard is inserted between the electrodes such as the point is perpendicular to pressboard allowing a radial propagation of discharges; and (2) a point-to-bar electrodes system allowing a propagation of discharges in one direction, tangentially to pressboard. The characteristics of discharges propagation, their shape, stopping length (the maximum extension of creeping discharge) as well as the associated current and electrical charge versus the thickness of pressboard and the type of oil are analyzed. It is shown that the magnitude and polarity of voltage, the type of oil as well as the thickness of pressboard influence the characteristics of discharges and especially the stopping length and density of branches. The stopping length of creeping discharges is shorter for pressboard/naturel esters' interfaces than with pressboard/mineral oil interface. [ABSTRACT FROM AUTHOR]

This paper presents the induced voltage measured at the terminal of a 10 kV distribution line when triggered lightning taking place at a distance of 40 m. It is shown that the induced voltage waveforms exhibit three components including a slow increase preceding the initial negative peak, following a rapid polarity reversal and the attenuated oscillations. The waveform parameters are defined in this paper. The observed negative peak value ranges from −47.1 kV to −7.5 kV. The positive peak value ranges from 5.3 kV to 20.9 kV, and the peak to peak value ranges from 12.8 kV to 63.2 kV. The test results show that the negative peak value of the induced voltage at the terminal of distribution generated by nearby negative triggered lightning generally exceeds the positive peak value, and in some cases the negative peak value even reaches twice the positive peak value. The negative 10%-90% rise time ranges from 2.3 μs to 88.5 μs, and the average oscillation period is about 18 μs. Both negative and positive peaks of induced voltages show good linear relationship with the peaks of lightning return stroke current. [ABSTRACT FROM AUTHOR]

The impulse grounding performance of distribution lines tower is the key factor to lightning protection. Few field high-current impulse test researches are conducted on distribution line tower. In this paper, we used a mobile high-current impulse generator to conduct test on a 10 kV distribution line tower. The peak value of the current injection is 6 kA to 16 kA. The impulse impedance and the surface potential distribution are measured and analyzed. Based on the CDEGS software, an equivalent modeling of the experiment was carried out. The influence of soil ionization was taken into account by the method of changing the conductor radius through two rounds of calculation. The simulation and measured results were basically consistent. Experiments have shown that the soil ionization effect has an important impact on lightning performance of distribution line tower. The graphite earthing modules (GEMs) and pulling wires can significantly reduce the impulse impedance of the tower. The potential rise of the earth surface at a distance of 30 m from the tower can reach 1 kV at peak, under an injection of 7.15 kA. [ABSTRACT FROM AUTHOR]

In medium-voltage distribution lines, lightning outages associated with indirect strokes are less frequent when surge arresters are installed at close intervals. In this case, the lightning performance is mainly determined by the line response due to direct strikes, usually assessed disregarding the effect of the lightning electromagnetic pulse (LEMP). This paper examines the influence of such an electromagnetic effect on the voltages across the line insulators caused by direct lightnings. The presence of both surge arresters and a shield wire is considered. By means of adequate modeling and numerical calculations, we show that the flashover rate due to the direct strikes is increased by the LEMP. The obtained results indicate that in the statistical assessment of the direct lightning performance of lines equipped by surge arresters and shield wires, the LEMP effect is not negligible and its accurate evaluation is hence required. [ABSTRACT FROM AUTHOR]

Although the underlying phenomena when grounding electrodes discharge lightning currents are very complex, it is possible to derive simple formulas of impulse characteristics that allow for important engineering estimates. The interest in simple formulas was recently renewed, resulting in many contributions in the literature. In this paper, a parametric analysis is performed by a simulation of time-domain responses, with parameters in broad ranges. From this study, new formulas of impulse characteristics have been derived, including the expressions for ranges of parameters when grounding electrodes exhibit dominant inductive, resistive, or ionization effects. New formulas are compared with the existing ones, with experimental results, and their accuracy has been investigated. [ABSTRACT FROM AUTHOR]

During the decades-long operation, oil paper insulation in power transformers may suffer the effect of thousands of lightning impulses. Such interesting but rarely studied phenomenon, also known as accumulative effect, may cause irreversible damage to the oil paper insulation, or even premature failure. Therefore, in this work, the influence of repeated lightning impulses on the oil paper insulation, especially the mechanism behind this phenomenon, was experimentally investigated. We determined the accumulative breakdown characteristics of the oil paper insulation and observed the influence of the repeated lightning impulses on the dissolved gas in oil and the degree of polymerization. Specifically, the space charge distribution in the oil paper samples and the relationship between the interval time and accumulative breakdown characteristics were experimentally determined in the end. The test results indicate that the accumulative effect only exists in the cellulose paper rather than the transformer oil. Such effect was considered to be the consequence of electrical degradation and accumulation of space charge. [ABSTRACT FROM AUTHOR]

This paper presents the results of experimental studies about the prebreakdown phenomena in mineral oil under lightning impulse. Experiments were carried out in a non-uniform field setup with HV electrode covered by crepe paper. The results of the experiments were compared with the results of research performed for bare HV electrodes. The onset voltage, propagation velocity, time to initiation, shadowgraph photos of discharges and light emission were respectively measured or recorded during the experiments. Analysis of the research outcomes indicates that the fundamental role of paper insulation is to raise the onset voltage by shoving away the onset sites out of the region of high field stress. The insulation wrapping does not have an influence on the shape of discharge patterns and on the propagation velocity. Some of the results connected with the times to initiation points that the mechanism of discharge initiation at the HV electrode surface does not depend on the fact it is insulated. The source of ?weak points? of the paper-oil insulation system is the oil, not the surface of insulation wrapping or metal of electrode. Observation of the oscillograms of light emitted by discharge channels indicates the difference in the mechanism of discharge propagation. The surface and space charge carriers left in the interelectrode space after discharge flash play an important role. In the case of insulated electrodes, the surface charge remains longer on the surface of electrode, reducing the electric field stress which is responsible for reignition. Simultaneously, the space charge reduces the degree of channel ramification. Both the observations are clearly visible on the oscillograms of light as differences in the frequency of light impulses and their peak values. [ABSTRACT FROM AUTHOR]

Wall fusion of buried pipelines can occur if the driving voltage and available current is sufficiently high. For example, it can occur from direct lightning strikes to earth, close to the pipelines’ routing. However, not all factors for defining the energy discharge needed to fuse the pipe wall are thoroughly investigated or understood. This paper enriches the ongoing research activities in an attempt to understand such detrimental damages. In particular, the paper formulates its research contents around a documented wall fusion incident on an underground gas transmission system, due to a nearby direct lightning strike. The investigation embraces field, laboratory, and modeling activities to provide insights on the damaging mechanism. Of particular importance in understanding this mechanism is the influence of soil ionization. To this end, a model is developed to investigate the soil-ionized flow of the lightning discharge current—into the pipeline's metal wall, through existing coating defects—thus revealing its detrimental effect. [ABSTRACT FROM AUTHOR]

High entrance capacitances of ultrahigh-voltage (UHV) transformers make it difficult to generate impulses with standard front time during the lightning impulse tests. In this paper, we discuss the feasibility of examining the longitudinal insulation design of a transformer via impulses with a front time longer than the standard value. We consider the following features: transient voltage distributions and insulation characteristics of longitudinal insulation. The transient voltages of two UHV windings are measured with a capacitive voltage sensor under impulses with different front times. The results demonstrate that the front time of the applied impulse has little effect on the gradient voltage distributions and the oscillatory component of the transient voltage, but it determines the front time of transient voltages. Therefore, the relationship between breakdown characteristics of the turn-to-turn insulation and the front time is studied. Experimental results revealed that whatever the insulation thickness, an increase in the front time of the applied impulse decreases the breakdown voltage, but this variation is within acceptable tolerance when the front time changes from 1.2 μs to 6 μs. Thus, as long as the front time is restricted within 6 μs, we can ensure the validity of lightning impulse tests on the examination of longitudinal insulation designs. [ABSTRACT FROM AUTHOR]

This two-part paper is intended to inform power system engineers, electrical engineering academicians, and suppliers of electrical apparatus of the threat of wildfires initiated from mal-operation of electrical grids and the unexploited opportunity to develop proper solutions and preventive means to such lethal events. This part (Part I) reviews and categorizes research in different fields of science and industrial projects that attempt to address wildfire issues. The topics include prediction and prevention means, detection methods, monitoring and surveillance techniques, suppression methods, allocation and mapping algorithms, and a summary of research and educational efforts. Subsequently, this paper highlights the damages and negative effects that a wildfire can cause to the electric grid and the interruptions to its continuous operation. Finally, this paper analyzes and categorizes the various scenarios of faulty electrical networks that may lead to wildfires. Part I of this paper provides the ground work and information for the solutions and discussions presented in Part II. [ABSTRACT FROM AUTHOR]

Dependence of lightning electric field waveform parameters on distance between the lightning channel and the field measuring point is examined. The analyses are performed based on representative wideband electric field waveforms that were obtained by averaging individual waveforms produced by negative return strokes at distances ranging from 10 to 500 km. The methodology employed for finding the representative waveforms using a large database is described in the companion paper. In this article, we present evolution with distance of the following waveform parameters: zero-to-peak rise time, zero-crossing time, ratio of the initial electric field peak to the opposite polarity overshoot, all for the ground wave, and the ratio of the ground wave initial electric field peak to the peak of the first skywave. We also present a catalog of representative waveforms for different distances, time of day, and stroke order. Additionally, we examine the peak-to-peak and zero-to-zero time intervals between the ground wave and the first skywave that are often used for estimating the apparent ionospheric reflection height. [ABSTRACT FROM AUTHOR]

This paper is aimed at the variation of AC and lightning impulse (LI) breakdown voltages of samples enriched with fullerene (C 60) nanoparticles (NPs) of natural ester, which stand out as an alternative to mineral oils. C 60 nanofluids with long-term stability and good dielectric properties are examined in this study on five samples for concentrations of NPs ranging 0.05 to 0.4 g/L concentrations. The AC and LI breakdown voltage measurements of each sample are repeated thirty times and the conformity of these measurements of the normal distribution is tested with the Shapiro-Wilk test. Conformity of all samples to normal distribution is accepted by this test and withstand voltages are calculated at 1%, 10% and 50% breakdown probabilities. The AC breakdown voltage performances of 0.3 and 0.4 g/L C 60 nanofluids are increased compared to natural ester. This increase rate is 5.1% and 7.8%, respectively. The withstand voltages at 1% and 10% breakdown probabilities increase by 20.2% and 13.2% compared to natural ester at 0.4 g/L C 60 nanofluid. 0.1 g/L C 60 nanofluid has 8.2% better performance than natural ester at LI breakdown voltages. Withstand voltages of 1% and 10% probability of this nanofluid are 6.5% and 7.7% higher than natural ester, respectively. These measurement results show that C 60 doped nanofluids can meet performance requirements in power system equipment with high power demands. [ABSTRACT FROM AUTHOR]

This paper presents a systematic investigation into the performance of a shielding wire on 10 kV overhead lines (OHLs) against indirect lightning, from the design point of view. The design parameters addressed include the grounding interval, grounding resistance, and position of the shielding wire. As a system outage is usually caused by insulator flashover at OHL poles under indirect lightning, the induced voltages there are investigated with the code developed from the Agrawal model. In the evaluation, the location of a lightning return stroke relative to a grounded or ungrounded pole is considered. It is found that the lightning channel positioned in the front of an ungrounded pole could completely wipe out the effect of the shielding wire. This occurs if the wave from the grounding point arrives later than the time to the peak of the voltage directly arising from the lightning return stroke. It is suggested providing the wire grounding at every pole even if the grounding resistance at some poles is much higher than the design value. Grounding spacing does not affect the induced voltages at the pole generally if the pole has been grounded. One critical parameter is identified, i.e., the distance between the shielding and outer phase wires. Minimizing the distance can effectively reduce the lightning-induced voltages. [ABSTRACT FROM AUTHOR]

High-frequency overvoltages are most dangerous for the insulation of transformer coils. It is because high-frequency pulse voltage creates an uneven distribution of voltage across the windings. The coil's first turns receive a disproportionately high voltage drop, leading to the inter-turn circuit. The paper analyzes the types of lightning pulses and proposes a new suppression method based on the anomalous skin effect in a multilayer material and the design in the form of a coil. The developed device is simulated, and the results of overvoltage monitoring at the substation with the installed high-frequency overvoltage suppression device are analyzed. [ABSTRACT FROM AUTHOR]

This paper proposes a novel layout for a grid-connected DC wind farm (DCWF) and investigates the performance under continuous operation and direct lightning strikes particularly for high soil resistivity. The DCWF employs internal dc grid that supplies generated power to the host AC utility through high voltage direct current (HVDC) transmission link. The proposed layout ensures sustainability of power supply against potential interruptions of DCWFs either during normal conditions or lightning incidents to comply with grid codes regulations. During continuous operation, the proposed layout safeguards the entire DCWF cables against flow of return currents to avert derating of conductor ampacity. Besides, protects WT nacelle switchgear and entire interface converters against hazards of surge currents. Furthermore, an effective grounding system design is proposed to introduce a low impedance path for system return currents, minimize voltage drop across grounding impedance and thus maximize DCWF delivered power to the grid. A detailed system that sufficiently represents models of system cables, grounding network and interface converters is built to verify the proposed scheme significance. The obtained results assure the capability of proposed layout to cease return currents via cable sheath during continuous operation and provide superior mitigation of lightning-associated transient voltages and currents. [ABSTRACT FROM AUTHOR]

A new approach to the characterization of CG lightning electric field waveforms using a large database is presented. The waveforms, recorded in a wide (160 Hz–500 kHz) frequency range, are categorized into groups, depending on stroke order (first or subsequent), time of day (to distinguish between the daytime and nighttime ionosphere heights), and distance range. For each group, a representative waveform (including the ground wave and one-hop skywave) was found by averaging a large number of individual amplitude-normalized waveforms on a -100 to 500 μs time scale (t = 0 corresponds to the peak of the return-stroke ground wave). In this article, the methodology of waveform classification and averaging is presented and discussed. In the companion paper, the developed methodology is applied to analyzing variation of lightning electric field waveforms of different type with distance in the 10 to 500 km range. [ABSTRACT FROM AUTHOR]

SF6 is widely used in high voltage equipment because of its outstanding characteristics as insulation medium. However, SF6 is a potent greenhouse gas, so its use and emission are regulated. CF3I has been investigated as a candidate for SF6 alternative gas, whose environmental impact is much less than that of SF6 and other fluorocarbon-based gases. In addition, a flexible gas-insulated transmission line (FGIL) is expected to be used for power transmission from offshore wind farms due to its high flexibility and low capacitance. In this paper, the feasibility of 22 kV class FGIL utilizing atmospheric pressure CF3I gas is evaluated from the viewpoint of withstand voltage with actual lightning impulse tests. The cross-sectional size of FGIL is determined by considering insulation condition, heat transfer condition, sheath electric field condition and spacer stress condition. The impulse tests for FGIL are conducted in straight and bent states, and it is revealed that the 50% breakdown voltage V50 of straight state exceeded lightning impulse withstand voltage (LIWV) for 22 kV class, and that V50 of bent state falls below LIWV. [ABSTRACT FROM AUTHOR]

Seven decades have passed since the Schumann resonances (SRs) were identified. Since then, their research interest has increased, currently being a topic of significance. Nonetheless, the papers that study their nature from the frequency perspective are in clear majority regarding those who focus on the time domain. To fill this gap in the literature and further characterize the SRs, a method to perform statistical analysis on the SRs signal in the time domain has been developed. For any given segment of data, the analysis performs a maximum likelihood estimation (MLE) of the statistical parameters from a group of previously selected distributions. After that, the best fit among the target distributions is selected through the application of Akaike information criterion (AIC). The method is tested by analyzing a month’s worth of data, showing the general analysis’ results and discussing the relationship between the chosen target distributions and common aspects between the time segments fitted to them. The reliability of the method’s results is also discussed by looking at different aspects of the analysis. Special emphasis is put over the results being correlated with lightning activity. This correlation highlights the usefulness of the method, given the well-established relationship between lightning and SRs. [ABSTRACT FROM AUTHOR]

The lightning performance of an overhead line due to indirect strokes is a measure of its ability to resist to surges produced by nearby lightning. The estimation of the lightning performance generally requires a huge number of calculations requiring computationally intensive simulations. In this paper, we present an approach that uses analytical expressions, leading to a very significant reduction of the required computer resources. By this analytical approach, we investigate the lightning performance under different line arrangements; the study is also devoted to assessing the improvement that can be obtained by addition of underbuilt shield wires to arrangements in which only upper shield wires are typically used: it is shown that such a measure can lead to significant enhancements in terms of lightning performance. [ABSTRACT FROM AUTHOR]

Overhead lines are important parts of distribution networks at present. Assessment and prediction of their health status is of great significance to ensure the reliable operation of distribution network. This paper presents a method for assessing and predicting the health status of overhead lines based on health index (HI). First, the key features set of overhead lines including ontological and nonontological factors is determined. Then, a calculation method for evaluating HI based on analytic hierarchy process and technique for order preference by similarity to an ideal solution is proposed. Subsequently, the health assessment results of the actual 110 and 10 kV overhead lines located in China show that the proposed method could reflect the actual situation of overhead lines well. Finally, based on the proposed method, this paper takes two areas of China, Beijing and Nanjing, which have different climatic conditions, as research objects, and studies the influence of natural factors on the health status of overhead lines, respectively. Based on the analysis results, the health statuses of the overhead lines in the two regions are predicted. The research results of this paper can provide guidance for the operation and maintenance of overhead lines. [ABSTRACT FROM AUTHOR]

The Cooray–Rubinstein formula (C–R formula) has been widely used to calculate the horizontal electric field generated by a lightning return stroke over the lossy ground. To evaluate the time-domain C–R formula by a recursive convolution, an alternative method is proposed in this paper, where the formulation in terms of the “step response” corresponding to the ground surface impedance, denoted as $k_{\varepsilon }(t)$ , is evaluated by the numerical inverse Laplace transform (NILT). Considering the good performance of Talbot's method for the NILT, Talbot's method is adopted to express $k_{\varepsilon }(t)$ in terms of a series of exponential functions, which can avoid the tedious piecewise approximation used by the available method and make the recursive convolution easier to program. In addition, some key formulae for the recursive convolution with complex poles and residues are presented in this paper. Numerical examples are provided to validate the proposed method. [ABSTRACT FROM AUTHOR]

This paper analyses the inherent difficulties in measuring the horizontal electric field from lightning and proposes some solutions to mitigate the contamination effect of the overwhelming vertical electric field. The analysis is carried out with a set of time-domain equations for the calculation of the electromagnetic fields from lightning. As these equations are scattered in several publications, in this paper they are compiled and presented in a harmonized form. Moreover, one new expression for the vertical electric field slightly below the ground surface is presented. It is shown that the horizontal electric field at the surface of lossy ground can be measured with minimum disturbance caused by the vertical electric field if the field sensor is placed slightly below the ground surface. This paper also shows that the horizontal electric field above the ground surface could be measured with the help of a pair of field sensors conveniently arranged so that the influence of the vertical electric field on the measurement is cancelled. [ABSTRACT FROM AUTHOR]

Modeling of lightning return-stroke channel affects significantly the estimation of fast-front overvoltages arising across overhead line insulators, thus, also the lightning performance of power lines. This paper introduces a simplified method for estimating the minimum lightning currents causing shielding failure flashover and backflashover of overhead transmission line insulation, as affected by lightning channel equivalent impedance. The validity of the proposed methodology is demonstrated through ATP-EMTP simulations of typical 66 up to 765-kV overhead transmission lines with variable tower ground resistance. An assessment is made of the effects of lightning channel equivalent impedance on the lightning performance of overhead lines, that is, shielding failure flashover and backflashover rates. Lightning channel equivalent impedance values of 1000 and 400 Ω are suggested, respectively, for shielding failure and backflashover studies, based on the results obtained in this paper together with a discussion on the literature data regarding channel impedance. [ABSTRACT FROM AUTHOR]

Wind turbine generators in a windfarm are connected by underground cables. Lightning sometimes strikes a nacelle or a blade. Lightning overvoltages due to a direct lightning strike to the system cause damages in the underground cable. Many parameters should be investigated to establish a rational lightning protection design for wind power generation system. Numerical simulation is a useful method to discuss the influence of the parameters on the lightning overvoltages. This paper uses an Electro-Magnetic Transients Program for the lightning surge analysis. This paper discusses the influence of grounding method of metallic sheath of the cable and grounding resistance on the lightning overvoltages for the direct lightning strike to the generation system. [ABSTRACT FROM AUTHOR]

The frequency dependence as well as the current dependence of grounding resistance affects lightning overvoltages in electric power system. This paper proposes an equivalent circuit to simulate the frequency dependence of soil resistivity and permittivity. Constants of the equivalent circuit are determined based on empirical formulas for the frequency dependence of the soil parameters proposed by Alipio and Visacro. The equivalent circuit is represented in time domain. Therefore, the equivalent circuit is applicable to the calculation of the current dependence of the grounding resistance. An influence of the frequency dependence of the soil resistivity and permittivity on the current dependence of the grounding resistance is discussed by the use of the equivalent circuit. This paper proposes a modified CIGRE model to calculate the current dependence of the grounding resistance. The equivalent circuit is very convenient and useful for engineers to carry out lightning surge analysis. [ABSTRACT FROM AUTHOR]