Search

This paper presents a novel seven-level inverter topology for medium-voltage high-power applications. It consists of eight active switches and two inner flying capacitor (FC) units forming a similar structure as in a conventional active neutral-point-clamped (ANPC) inverter. This unique arrangement reduces the number of active and passive components. A simple modulation technique reduces cost and complexity in the control system design without compromising reactive power capability. In addition, compared to major conventional seven-level inverter topologies, such as the neutral point clamped, FC, cascaded H-bridge, and ANPC topologies, the new topology reduces the dc-link voltage requirement by 50%. This recued dc-link voltage makes the new topology appealing for various industrial applications. Experimental results from a 2.2-kVA prototype are presented to support the theoretical analysis presented in this paper. The prototype demonstrates a conversion efficiency of around 97.2% ± 1% for a wide load range. [ABSTRACT FROM AUTHOR]

This paper proposes a novel discontinuous pulse-width modulation (DPWM) method to reduce the current harmonics and improve the system efficiency for a single-phase three-level neutral-point clamped inverter. In single-phase inverters, the unipolar pulse-width modulation (UP-PWM) method is commonly used. However, this method has the disadvantage of power losses due to numerous switching operations. Conventional DPWM methods reduce the power losses and improve efficiency but increase the current total harmonic distortion (THD). To overcome these weaknesses, this paper proposes a hybrid DPWM switching method combining two PWM methods: the UP-PWM method and the conventional DPWM method called one-pole clamped PWM method. Since the proposed DPWM method offers all the advantages of both PWM methods, the optimal performance—with regard to the power losses and current THD—is obtained. The combination of two PWM methods is investigated by analyzing the power losses and current THD. Based on the analysis, the process determining the optimal operating condition is introduced. The effectiveness of the proposed DPWM method is demonstrated through simulations and experiments. [ABSTRACT FROM AUTHOR]

The output voltage of power electronic converters is a very important quantity for dynamic control of power electronic systems. In electrical drives without electromechanical position or speed sensor, the terminal reference voltage is used to obtain the rotor position. Dead-time effects and semiconductor voltage drop lead to distortion in the actual output voltage and degrade the control performance when the back electromotive force magnitude is low. Thus, for stable low-speed operation, output voltage sensing becomes necessary. Due to the switching nature of power electronic systems, this is not a trivial task, especially when instantaneous measurement of the terminal voltage is required. In this paper, an instantaneous switching-period average voltage sensing technique is proposed that utilizes a combined approach of oversampling and filtering. Based on the theoretical analysis of the sampling- and filter-induced measurement distortion, a general solution for an optimal filter design is derived. The additional sensing circuit is integrated into the low-side gate driver of the converter outputs. This paper includes details about the hardware implementation and extensive verification measurements. [ABSTRACT FROM AUTHOR]

This paper proposes a new single-phase single-stage switched-boost inverter with four switches. Like the quasi-Z-source inverter and quasi-switched boost inverter (qSBI), the proposed inverter has the main features as continuous input current, buck/boost voltage with single-stage conversion, and shoot-through immunity. Compared to the qSBI, the proposed inverter uses one more capacitor and one less switch. This paper presents the operating principles, pulse-width modulation control strategy, parameter design guidelines, and simulation results for the proposed inverter. To verify the performance of the proposed inverter, an 800-W prototype was built with an 110 V/50 Hz output voltage in stand-alone and grid-connected modes. The simulation and experimental results matched those of the theoretical analysis. [ABSTRACT FROM AUTHOR]

In this paper, two structures are proposed for the switched-inductor quasi-Z-source inverter. In the proposed structures to extend the voltage gain of inverter, two new switched-inductor structures are used. In the proposed structures, voltage across the capacitors in the Z-source network and in the switched-inductor is symmetric and small. The other advantage of proposed inverters is known as achieving higher voltage gain per smaller duty cycle ratio (of shoot-through). Compared with a conventional continuous input current switched-inductor quasi-Z-source inverter at the same gain voltage, there is less of a ripple of input current in the proposed inverters. In this paper, at first the both the conventional and the proposed switched-inductor Z-source inventers are thoroughly investigated to find out their governing relations. Then, the proposed Z-source inverters are compared with the conventional ones by simulating them to assess their performance efficiency. Next, applying the simple boost pulse width modulation the simulation is carried out with PSCAD/EMTDC software. After that, to evaluate the obtained results, the prototypes of the proposed inverters with 48 Vdc input voltage are used. [ABSTRACT FROM PUBLISHER]

This paper deals with the analysis of the input dc-link voltage ripple in multilevel inverter based on H-bridge and level doubling network (LDN). The LDN is basically a half-bridge fed by a floating capacitor, with voltage self-balancing capability, recalling the concept of a flying capacitor configuration. The amplitude of the LDN voltage ripple is analytically determined considering both the low-order and the switching harmonic components. In particular, peak-to-peak distributions of voltage ripples over the fundamental period are analytically determined, making possible the design of dc-link capacitor relying only on the dc-voltage ripple requirements. The case study makes reference to negligible switching ripple in the output current. It well represents either grid connection or passive load having almost sinusoidal currents. Numerical simulations carried out by MATLAB/Simulink and a complete set of experimental verifications are given to confirm the theoretical developments. [ABSTRACT FROM AUTHOR]

In order to reduce switching loss of neutral point clamped three-level inverter (NPC TLI), generally discontinuous pulsewidth modulation (DPWM) is used. But it can result in dc offset and ac ripple on neutral point (NP) voltage. So a novel pulse sequence DPWM (NPSDPWM) is proposed to reduce switching loss and control NP voltage simultaneously in this paper. NP voltage is controlled by choosing proper clamping modes. To avoid unexpected switching action during changing clamping mode, an improved pulse sequence is also presented. The switching loss and NP voltage ripple of NPSDPWM, traditional and proposed DPWM in previous literature are compared, respectively. The experimental results show that NPSDPWM has well NP voltage control ability and the switching losses are reduced effectively. [ABSTRACT FROM AUTHOR]

In this paper, the zero sequence circulating current in open winding permanent magnet synchronous machine (OW-PMSM) drives with common dc bus is systematically analyzed for the first time. It is revealed that the zero sequence circulating current is affected by zero sequence back-electromotive force, cross coupling voltages in zero sequence from the machine side, pulse-width modulation induced zero sequence voltage, and inverter nonlinearity from the inverter side. Particularly, the influences from the cross coupling voltages in zero sequence and parasitic effect of inverter nonlinearity are investigated for the first time in this paper. Then, the synthetic model of the equivalent zero sequence circuit is proposed as well. Each cause is studied independently via analytical modeling, finite element analysis, and experiments. Meanwhile, to tackle this issue, the relevant suppression strategy using frequency adaptive proportional resonant controller is presented and tested on the 3 kW OW-PMSM platform. [ABSTRACT FROM AUTHOR]

This paper studies pulse width modulation (PWM) techniques suitable for a four-level five-phase open-end winding (OeW) drive. The drive comprises a five-phase induction machine, supplied using two two-level voltage source inverters with isolated and unequal dc-link voltages, in the ratio 2:1. A decoupled carrier-based (CB) PWM modulation strategy, based on unequal voltage reference sharing between the two converters, is introduced in this paper. The stability of dc-link voltages in OeW drives is investigated next, using a novel analysis technique. Several modulation methods are analyzed and the results show that application of the coupled PWM technique, with carriers having in-phase disposition, leads to overcharging of the capacitor in the dc-link of the inverter intended to operate with the lower dc-link voltage. On the other hand, the proposed decoupled CB PWM scheme naturally eliminates the dc-link capacitor overcharging problem. These findings are verified experimentally, using open-loop V/f control. Two different decoupled CB modulation methods are compared and the best performing modulation method is selected and incorporated further into an OeW drive with field-oriented control. The presented steady state and transient experimental results demonstrate that the decoupled CB PWM technique is suitable for high-performance variable speed drive applications. [ABSTRACT FROM AUTHOR]

This paper presents a pulse width modulation (PWM) technique for the minimization of the leakage current in the grid-connected/stand-alone transformerless photovoltaic (PV)-cascaded multilevel inverter (CMLI). The proposed PWM technique is integrated with the MPPT algorithm and is applied to the five-level CMLI. Furthermore, using the proposed PWM technique the high-frequency voltage transitions in the terminal and common mode voltages are minimized. Thus, the proposed PWM technique minimizes the leakage current of the PV array and electromagnetic interference filter requirement in the system without addition of any extra switches. Furthermore, this paper also presents the analysis for the terminal voltage across the PV array and the common mode voltage of the inverter based on the switching function. Using the given analysis, the effect of the PWM technique can be analyzed, as it directly links the switching function with the common mode voltage and leakage current. Also, the proposed PWM technique requires reduced number of carrier waves compared to the conventional sinusoidal pulse width modulation technique for the given CMLI. Complete details of the working principle and analysis with the support of simulation and experimental results of the proposed PWM technique are presented in this paper. [ABSTRACT FROM PUBLISHER]

This paper proposes a dual-space vector control scheme for the open-end winding permanent magnet synchronous motor (OEW-PMSM) drive fed by the dual inverter with a single dc supply. Potential zero-sequence current in the open-end winding drive system has to be considered since it causes circulating current in the winding and leads to high current stress of power semiconductor devices and high losses. Zero-sequence current in open-end winding ac motor drives is usually caused by the zero-sequence voltage, and therefore switching combinations which do not produce zero-sequence voltage are used to synthesize the reference voltage in existing methods. But even so, the zero-sequence voltage can also be produced by the dead time of the inverter. In order to suppress zero-sequence current in the OEW-PMSM drive, a dual-space vector control scheme is proposed and a novel dual-inverter space vector pulse width modulation (PWM) with the zero-sequence voltage reference is employed to regulate system zero-sequence voltage in this paper. Compared with existing dual inverter PWM strategies, the novel algorithm build a regulation mechanism for the zero-sequence voltage. The proposed method is compared with the conventional vector control by simulations and experiments, and the results shown that the proposed scheme can suppress zero-sequence current effectively. [ABSTRACT FROM AUTHOR]

Magnetically coupled impedance-source (MCIS) networks are recently introduced impedance networks intended for various high-boost applications. It employs coupled magnetic in the circuit to achieve higher voltage gain. Various MCIS networks have been proposed in the literature for myriad applications; however, due to effective role of system modeling in the closed-loop controller design, this paper is allocated to small-signal modeling and analysis of MCIS converters. The modeling is performed by means of the circuit averaging and averaged switch technique. A generalized small-signal derivation is demonstrated for pulse width modulation (PWM) MCIS converters and it is shown that the derived transfer functions can simply be applied to Y-source, Γ-source, and T-source impedance networks. Various transfer functions for capacitor voltage, output voltage, magnetizing current, input and output impedance are derived and have been validated through frequency and dynamic responses of computer simulation results. In addition, a comprehensive analysis has been done for all mentioned PWM MCIS converters regarding their circuit parameters. Furthermore, the effect of considering the equivalent series resistances of capacitor and inductor on the stability margin of MCIS converters is revealed in this paper. Finally, in order to validate the derived transfer functions and to consolidate the perfumed analysis, experimental results are presented for all mentioned MCIS converters. [ABSTRACT FROM PUBLISHER]

Based on the Z-source inverter, this paper proposes a novel commutation torque ripple reduction strategy for brushless DC motor (BLDCM). The proposed strategy employs the same modulation mode in both the normal conduction period and the commutation period, and the commutation torque ripple is reduced by regulating the shoot-through vector and active vector duty cycles. The proposed detection method acquires the end point of commutation by comparing the clamped terminal voltages with reference zero level, and the signal-noise-ratio of the detection is improved by avoiding the attenuation of the terminal voltages. Furthermore, a certain pulse width of the shoot-through vector can not only reduce the commutation torque ripple but also provide a new opportunity to detect the end point of commutation. Moreover, Z-source inverter provides the buck–boost ability for BLDCM drive system, then the dc voltage utilization can be improved, and the safety of the drive system can also be improved. In addition, this paper analyzes the terminal voltages during each vector. The experimental results verify the correctness of the theories and the effectiveness of the proposed approach. [ABSTRACT FROM PUBLISHER]

The increasing interest in multiphase drive systems has led to the extension of inverter topologies and pulse width modulation (PWM) methods from three-phase to multiphase occasions. Carrier-based PWM (CPWM) dominates space vector PWM when the phase number increases, because of its simple computation and modular implementation. Although intensive work has been done on modifying PWM methods to reduce the common-mode voltage (CMV), not enough work has been done on CPWM methods with CMV reduction for multiphase drives. This paper extends the phase-shifted sinusoidal PWM (PS-SPWM) method for five-phase and six-phase two-level voltage-source inverters (VSI) and employs the intersection-plotting method and Fourier analysis to reveal the nature of the CMV. Both experiment and simulation results comply with theoretical analysis that compared with the conventional SPWM, the PS-SPWM can effectively reduce the CMV in peak-to-peak value and RMS value, though it leads to a higher phase current distortion. In addition, the hardware realization of PS-SPWM for multiphase inverters by a distributed control system is presented in this paper. [ABSTRACT FROM AUTHOR]

Two three-level inverters driving an open-end winding induction motor can generate equivalent voltage waveforms as a single five-level inverter-based drive. In addition, it can bring in benefits such as reduced dc-link voltage, less number of devices, and fault-tolerant capability, which is favored in high-power motor drive applications. The main challenge with this type of configuration is the appearance of large zero-sequence current circulating between the two inverters, which generates extra losses in the switching devices and the motor as well as affects the normal operation of the machine. Another challenge is to balance the dc-link neutral point voltage of the two three-level inverters. This paper has proposed a simplified decoupled space-vector pulsewidth-modulation (PWM) strategy to eliminate the averaged zero-sequence voltage in each switching cycle by the placement of redundant vectors of each individual inverter using a time shift. Neutral point voltage balance is further achieved by adjusting the time duration of the redundant vectors. In this paper, it is shown that it is possible to operate this kind of drive configuration with a single dc power supply and achieve averaged zero-sequence voltage elimination and neutral-point voltage balancing at the same time. Experimental results of a 5.5-kW dual three-level inverter drive using the proposed PWM strategy are presented, which validates the control method and drive configuration. [ABSTRACT FROM PUBLISHER]

To reduce the common-mode voltage (CMV) and eliminate the CMV spikes for two-level voltage source inverters (2L-VSIs), an improved model predictive control (MPC) based CMV reduction method is proposed in this paper considering dead-time effects. First, an improved voltage vector (VV) preselection strategy is proposed to reduce the CMV spikes caused by the dead time. Second, a new hybrid VV preselection strategy based on a delay compensation strategy and a modified current sector division strategy is proposed to completely eliminate the CMV spikes. As the proposed hybrid VV preselection based MPC strategy makes full use of the six nonzero VVs of the 2L-VSI, the current total harmonic distortions and ripples are reduced. The simulation and experiments are carried out to verify the effectiveness of the proposed strategy. [ABSTRACT FROM AUTHOR]

In this paper, a novel space-vector pulsewidth modulation technique for a five-level active neutral-point clamped (5L-ANPC) inverter is proposed to eliminate the common-mode voltage (CMV). For the 5L-ANPC inverter, which produces a good output voltage performance and lowdv/dt, the total 125 voltage vectors can be generated, among which the proposed scheme employs only 19 voltage vectors producing a zero CMV. Due to the limitation of voltage vectors selected, the dc-link capacitor voltages of the 5L-ANPC inverter cannot be balanced by themselves. Therefore, the capacitor voltages of the inverter should be controlled by choosing the redundant switching states appropriately. The validity of the proposed modulation scheme has been verified by simulation and experimental results. [ABSTRACT FROM AUTHOR]

Common-mode voltage (CMV) is known as a major cause of premature motor failures. The form and amplitude of the CMV generated by any converter depends on both the circuit topology and modulation technique. Among single stage ac–ac converters employed in drive applications, the Z-source ultra sparse matrix converter (ZSUSMC) is a desirable choice due to reduced number of switches in its structure and voltage boosting capability. Based on these considerations, this paper aims to: 1) theoretically determine and compare the CMV of the ZSUSMC with four well-known impedance networks, namely, cascaded, switched-inductor, quasi, and series, in its structure and 2) propose modulation techniques for CMV reduction in the ZSUSMCs. To this end, first, it is shown that the ZSUSMC, depending on the impedance network used in its structure, provides more freedom to choose from redundant switching states compared to the ultra sparse matrix converter. Then, by taking advantage of this feature, novel modulation strategies that attenuate the CMV without affecting the boosting capability are developed. The proposed modulation schemes are based on avoiding the switching states most contributing to the CMV during a switching period. Through hardware-in-the-loop studies, the effectiveness of the proposed modulation strategies in reducing the CMV of the ZSUSMCs is verified. [ABSTRACT FROM AUTHOR]

In voltage-source inverters (VSIs), dead time is used to prevent shoot-through over switching devices. However, the existence of the dead time will distort the output phase current, which degrades the performance of the inverter as well as influences the common-mode voltage (CMV), particularly in CMV elimination relevant modulation schemes, such as zero-common-mode (CM) pulsewidth modulation (PWM)-based paralleled inverters. In the light of the situation that the normal sampling-based dead-time compensation (DTC) methods are often disturbed by the current ripple, this paper introduces a novel DTC method for the VSI, which can mitigate the impact of the current ripple and improve the accuracy of DTC. The proposed method deduces the real-time current ripple, which can reconstruct the actual trajectory of phase-leg currents, and the peak values corresponding to rising and falling edges for PWM signals can be predicted. In this way, DTC can be implemented based on the direction of relevant instantaneous switching currents and finally improves the accuracy. Especially, the current-ripple-prediction-based DTC can help to improve the CMV distortion caused by the dead time for paralleled inverters with zero-CM PWM. Simulation and experimental results are provided to validate that the proposed method can be applied to different topologies and modulation schemes with good performance. [ABSTRACT FROM AUTHOR]

This paper proposes a transformerless line-interactive uninterruptible power supply (UPS) with low ground leakage current. A high-efficiency bidirectional inverter is suggested, which performs the line-interactive UPS functions with low ground leakage current. It has a full-bridge inverter and a bidirectional switch, which operate with the unipolar pulsewidth modulation. Because the bidirectional switch operates at the line-frequency, switching losses can be lower than the previous transformerless inverters. As the inverter operates, the parasitic capacitance between the inverter and the ac voltage ground is clamped to zero voltage for a positive line cycle and to the ac voltage for a negative line cycle, respectively. Thus, the parasitic capacitance can be prevented from being charged or discharged, which ensures the absence of the ground leakage current. The operation modes of the proposed system are described. The control schemes are presented to design the proposed inverter for the line-interactive UPS. Experimental results for a 2.0 kW prototype are discussed to verify the performance of the proposed system. [ABSTRACT FROM AUTHOR]

This paper proposes the new clamping angle control (CAC) pulse width modulation (PWM) method to restore its maximum linear modulation range of voltage source inverters (VSIs) reduced by the duty ratio limitation in hardware implementation, which makes the VSIs to operate nonlinearly in the high modulation range. The deadtime and the bootstrap gate driver circuit mainly cause this duty ratio limitation in practice. In particular, the bootstrap gate driver circuit is used in many industrial applications by avoiding the additional power supply to apply the gate-source voltage of power switches, and therefore making the VSIs to be small size with the low cost. First, the proposed CACPWM method is theoretically analyzed. Then, it is applied in the high modulation range to overcome the limitation of the duty ratio due to the use of the bootstrap gate driver circuit. Thereafter, its practical effectiveness is verified by both simulation and experimental tests. Also, the resulting harmonic distortions are compared with those by the conventional PWM methods. [ABSTRACT FROM AUTHOR]

An adaptive control of DPWM implementable in clamped-three-level inverters with two strings of photovoltaic (PV) panels in cascaded connection is proposed in this paper. The proposed modulation is developed based on the so-called circuit-level decoupling concept. It is able to provide balance line voltage even under unbalanced dc links. The unequal dc voltages appeared due to asymmetric maximum point of power trackings (MPPTs) are controlled by proper injection of zero-sequence voltage to the common mode voltage, while the total dc voltage is regulated based on the voltage commands generated by the MPPT of each string. Thus, both PV strings are able to be operated based on their MPPTs while there is almost no low-order harmonic distortion at the inverter output current. Compared with the previous methods, the high capability of the proposed method is evaluated by simulation study and experimental tests. [ABSTRACT FROM AUTHOR]

This paper presents an improved analytical model for estimating the high-frequency current ripple of interior permanent magnet synchronous machines due to pulsewidth modulation (PWM) switching. The proposed model accounts for the impact of slotting effect, magnetic saturation, and cross-coupling between the $d$ - and $q$ -axis. The model is subsequently used to investigate several factors that influence the PWM-induced current ripple. These include the PWM switching frequency, fundamental frequency (i.e., machine speed), dc-bus voltage, current control angle (i.e., γ angle), and the excitation current amplitude (i.e., saturation level). Experiments have been conducted to verify the analytical prediction results. These results show that the analytical model can predict the PWM-induced current ripple waveshape very well for many operating conditions and accurately estimate its rms value over a complete fundamental period. [ABSTRACT FROM AUTHOR]

This paper investigates a multilevel inverter composed of series/parallel-connected H-bridges. The presented structure can be used for applications in which the use of semiconductor switches with low-voltage and low-current ratings is intended. A comprehensive system model, an overall control strategy to adjust the output voltage with constant magnitude and frequency, and a level-shifted PWM (LS-PWM) strategy based on a voltage vectors unidimensional analysis and a plane analysis are presented. The LS-PWM is capable of mitigating the low-frequency circulating current, thus generating multilevel voltage signals with low harmonic distortion, maximum number of levels, and low dv/dt. In addition, considering a wide range of values of voltages and currents and various power levels, the total converter losses are reduced compared with the conventional multilevel converters. Two multilevel conventional inverters with the same number of semiconductor switches are used for comparison. Simulation and experimental results demonstrate the feasibility of the studied converter. [ABSTRACT FROM AUTHOR]

This paper presents a nine-level transformer-based inverter requiring only eight switches. The envisaged structure consists of two standard H-bridges fed from a single dc source. Besides, a single-phase transformer is employed to aid the process of intermediate voltage level generation. An ad-hoc pulsewidth modulation scheme based on boolean logic form equations is developed to derive the gating pulses. An effortless extension of the proposed inverter to a higher number of voltage levels is also achieved by generalizing the switching functions. Furthermore, the superior performance of the proposed topology is demonstrated through a comprehensive cost-based analysis. Finally, the validation of the proposed topology is accomplished through experiments on a down-scale prototype, and the measurement results are included. [ABSTRACT FROM AUTHOR]

In order to prevent the power switching devices (e.g., an insulated-gate bipolar transistor, IGBT) from shoot-through in voltage-source converters during a switching period, the dead time is added either in the hardware driver circuits of the IGBTs or implemented in software in pulse width modulation (PWM) schemes. Both solutions will contribute to a degradation of the injected current quality. As a consequence, the harmonics induced by the dead time (referred to as “dead-time harmonics” hereafter) have to be compensated in order to achieve a satisfactory current quality, as required by standards. In this paper, the emission mechanism of dead-time harmonics in single-phase PWM inverters is, thus, presented considering the modulation schemes in detail. More importantly, a repetitive controller has been adopted to eliminate the dead-time effect in single-phase grid-connected PWM converters. The repetitive controller has been plugged into a proportional-resonant-based fundamental-frequency current controller so as to mitigate the dead-time harmonics and also to maintain the control of the fundamental-frequency grid current in terms of dynamics. Simulations and experiments are provided, which confirm that the repetitive controller can effectively compensate the dead-time harmonics and other low-order distortions, and also, it is a simple method without hardware modifications. [ABSTRACT FROM AUTHOR]

This paper presents a hybrid pulse width modulation-based discontinuous modulation (D-HPWM) strategy with dc-link voltage balancing for a three-level neutral-point-clamped (NPC) traction inverter drive. The results are then compared with continuous-hybrid-PWM (C-HPWM) to check the performance improvement. The HPWM strategy uses both the advantages of carrier- and space-vector-based PWM strategies. The duty cycles are generated using the carrier-based strategy to reduce the computational time and complexity of the system and redundant vector states are used to keep the two dc-link capacitor voltages balanced. As discontinuous PWM (DPWM) reduces the switching losses considerably compared to the continuous PWM, the DPWM strategy is developed in this paper for the HPWM-based strategy. Detailed comparison studies are then carried out in MATLAB/Simulink and PLECS to show the conduction and switching loss distribution with change in modulation index for different power switches. A 54.0-kW surface permanent magnet synchronous machine (PMSM) is used for this simulation studies. Moreover, the total inverter loss and losses in each insulated gate bipolar transistor (IGBT) are also compared. Detailed experimental performance analysis is also carried out with a scaled down prototype of a 6.0-kW surface PMSM, NPC inverter, and real-time emulator DSpace, to show the capacitor voltage deviation with both control strategies. [ABSTRACT FROM PUBLISHER]

This paper characterizes the sampling effect in digital sinusoidal pulse width modulation (SPWM) of voltage source inverter (VSI). The time-domain analysis presented in this paper establishes the relation between the fundamental frequency, carrier frequency, and the sampling frequency at different modulation indices of the SPWM. The analysis investigates the effect of sampling frequency of the digital controller on the output of the VSI. It is shown that the low-frequency harmonic components appear in the frequency spectrum of the VSI output voltage due to sampling. As a result, the output current of digitally controlled VSI is stepped in nature. The double Fourier integral solution of the switched waveform for inner and outer integral limits has been used to derive the expression. The integral solution is obtained using Jacobi-Anger expansions. The generalized results developed in this paper are useful to investigate the sampling effect in high switching frequency DSPWM. The proposed sampling effect has been analyzed for SPWM of single-phase H-bridge inverter. The analytical results are verified using simulation and experimental results. The experimental results have been obtained with the use of field-programmable gate array (FPGA) as a digital controller. [ABSTRACT FROM PUBLISHER]

A new pulsewidth modulation (PWM) strategy which is an alternative approach of the discontinuous PWM (DPWM) for a three-level neutral-point-clamped (NPC) inverter is proposed in this paper. A three-level NPC inverter is completely mature and very well-established topology in high-power applications. However, the three-level NPC inverter has an inheritance problem of the neutral-point voltage unbalancing due to the split dc-link capacitors. This structure can cause large neutral-point voltage ripple. Furthermore, output currents of the three-level NPC inverter are distorted by the neutral-point voltage ripple. Therefore, the neutral-point voltage must be controlled. In this paper, a new DPWM method using two different offsets for the neutral-point ripple reduction is proposed and the effectiveness of the proposed DPWM method is verified by using the simulation and the experimental results. [ABSTRACT FROM PUBLISHER]

A four-level five-phase open-end winding (OeW) drive topology is introduced in this paper. The drive comprises a five-phase induction machine with open-end stator windings, supplied using two two-level voltage-source inverters with isolated and unequal dc-link voltages, in the ratio 2 : 1. The topology offers the advantages of a modular structure with fewer semiconductor components and has a greater potential for fault tolerance, as compared with an equivalent single-sided four-level drive. Due to the large number of switching states, development of a suitable space vector pulsewidth-modulation (PWM) method can be challenging. Hence, this paper examines the implementation of two-level-shifted carrier-based PWM methods. The effect of dead time on the drive performance is discussed, and it is shown that simultaneous PWM switching of both inverters can lead to degraded output phase voltage waveforms. Detailed analysis of this phenomenon is presented, a solution is proposed, and the modified modulation techniques are incorporated in an experimental setup, at first in conjunction with $V/f$ control. Once the proof of concept has been provided, full field-oriented control is implemented in this OeW drive topology for the first time; detailed experimental testing is conducted, and results are reported. [ABSTRACT FROM AUTHOR]

Based on the Z-source inverter, this paper proposed a novel approach to zero-crossing point (ZCP) detections during the shoot-through vectors for sensorless brushless dc motor (BLDCM). The proposed approach separates the ZCP detections from speed adjustment, and makes the shoot-through vector not influence the motor speed-adjustment directly, while the zero-vectors and active-vectors are used exclusively to adjust the speed of BLDCM. With the proposed approach, the sensorless BLDCM can operate in a wide speed range without switching the detection points and the reference levels, and it is unnecessary to change the reference levels according to the PWM technique. The terminal voltages limited by diode can be directly compared with the reference zero level during the shoot-through vectors, so as to reduce the detection error caused by attenuation. Moreover, Z-source inverter not only provides boost voltage for sensorless BLDCM drive system, but also improves the utilization rate of dc source voltage and the safety of the drive system. In addition, this paper analyzed the terminal voltages of the floating phase during each vector. The experimental results verified the correctness of above theories and proved the effectiveness of the proposed approach. [ABSTRACT FROM AUTHOR]

Pulse width modulation (PWM) converters generate switching common-mode voltages (CMVs) across the load terminals. These voltages cause common-mode currents, leading to bearing failure in motor loads and electromagnetic interference problems. This paper presents a generalized carrier-based PWM technique for open-end winding motor drives that completely eliminates switching CMV. The proposed method is applicable to both dual two-level voltage source inverter and dual matrix converter-based open-end winding drives. Detailed analysis shows that the carrier-based method requires significantly less computation compared to the corresponding space vector implementation. This paper also outlines the relationship between the two implementations. The carrier-based method is shown to achieve superior performance in terms of resource requirements and execution time when implemented on a field-programmable gate array-based real-time control platform. Simulation and experimental results have been presented to validate the proposed method. [ABSTRACT FROM AUTHOR]

This paper presents a new multilevel selective harmonic elimination pulse-width modulation (MSHE-PWM) technique for transformerless static synchronous compensator (STATCOM) system employing cascaded H-bridge inverter (CHI) configuration. The proposed MSHE-PWM method optimizes both the dc-voltage levels and the switching angles, enabling more harmonics to be eliminated without affecting the structure of the inverter circuit. The method provides constant switching angles and linear pattern of dc-voltage levels over the modulation index range. This in turns eliminates the tedious steps required for manipulating the offline calculated switching angles and therefore, easing the implementation of the MSHE-PWM for dynamic systems. Although the method relies on the availability of the variable dc-voltage levels which can be obtained by various topologies, however, the rapid growth and development in the field of power semiconductor devices led to produce high-efficiency dc-dc converters with a relatively high-voltage capacity and for simplicity, a buck dc-dc converter is considered in this paper. Current and voltage closed loop controllers are implemented for both the STATCOM and the buck converter to meet the reactive power demand at different loading conditions. The technique is further compared with an equivalent conventional carrier-based pulse-width modulation to illustrate its enhanced characteristics. The effectiveness and the theoretical analysis of the proposed approach are verified through both simulation and experimental studies. [ABSTRACT FROM AUTHOR]

This paper presents a fast and generalized space vector pulse width modulation (SVPWM) scheme for any multilevel inverter. The SVPWM scheme generates all the available switching states and switching sequences based on two simple and general mappings, and calculates the duty cycles simply as if for a two-level SVPWM, thus independent of the level number of the inverter. Because the switching states, duty cycles, and switching sequences are all obtained by simple calculation in the proposed SVPWM scheme, no lookup table is needed and the scheme is computationally fast. The generalized method of generating the switching states (first mapping), calculating the duty cycles, and determining the switching sequence (second mapping) is described in this paper. The scheme is suitable for any reference vector with any modulation index, and can be conveniently extended to meet specific requirements, such as symmetric switching sequences. Compared with prior methods, the SVPWM scheme proposed in this paper provides two more degrees of freedom, i.e., the adjustable switching sequences and duty cycles, thus offering significant flexibility for optimizing the performance of multilevel inverters. The influence of redundant switching sequences in the output phase voltage of inverters is demonstrated for a nine-level inverter. This paper also thoroughly compares the proposed SVPWM scheme with prior methods. Both simulation and experimental results are given. [ABSTRACT FROM AUTHOR]

Three optimized pulse-width modulated (PWM) techniques for the overmodulation region of two-level inverter-fed ac drives are introduced and investigated from the harmonic loss minimization point of view. The optimization is elaborated for the lowest loss-factor, which is proportional to the square of the root mean square value of current harmonics. The loss-factors are computed for different switching numbers as the function of the motor fundamental voltage. It is shown that, with respect to the motor heating and torque ripples, the acceptable drive condition can be guaranteed by a relatively low value of an inverter switching frequency up to 96%–97% of maximal possible motor voltage. Furthermore, it is shown that the so-called three-vector methods have considerably better performance in the lower part of the overmodulation region than the so-called two-vector method for the same number of switching. The performance of the techniques is compared with other existing PWM techniques. This paper discusses the implementation details of the proposed optimal PWM techniques. The theoretical results are verified by experimental and simulation tests. [ABSTRACT FROM AUTHOR]

In trasformerless grid-connected photovoltaic (PV) systems, common-mode voltage (CMV) fluctuations cause leakage current flow through the stray capacitance of the PV panels. Shoot-through states in a quasi-Z-source inverter (q-ZSI) increase the amplitude of high-order harmonics of CMV. In this paper, by using the modulation technique based on odd pulse width modulation and minor change in the Z network of the three-phase q-ZSI, the leakage current is blocked. No extra semiconductor element is added. By the proposed technique, CMV is kept nearly constant during switching cycles. The experimental results for CMV analysis in a \text1\;\textkW prototype are presented to verify the theoretical analysis. [ABSTRACT FROM PUBLISHER]

Multilevel inverters (MLIs) have replaced conventional two-level inverters for medium-voltage high-power industrial applications. One of the best modulation techniques for MLIs is the space vector modulation (SVM). Although SVM has its own advantages, it has been overlooked for much simpler carrier-based modulation schemes in the industry. Nearest level modulation (NLM) is a simple alternative, which is functionally similar to SVM. In this paper, a new generalized SVM algorithm is presented, in which the SVM is achieved using the concept of NLM. A generalized switch matrix is introduced to derive gate pulses for the inverter, which further simplifies the algorithm. The algorithm is tested and verified for a three-phase, three-level, and five-level neutral-point-clamped inverters in both simulation and hardware. [ABSTRACT FROM PUBLISHER]

In this paper, dual-buck structured single-stage buck–boost inverters that use power MOSFETs to achieve high efficiency are presented. The proposed inverters require fewer switches, and half of the switches have reduced current stresses. They have no shoot-through problem; therefore, high system reliability can be obtained. The dead-time in PWM signals can be minimized or eliminated, which improving the quality of the output ac voltages and increasing the efficiency. In the proposed inverters, MOSFETs can be used without reverse-recovery issues of their body diodes to boost the efficiency and increase the switching frequency. To further improve the efficiency and stability of the proposed single-phase inverter, PWM strategies combining high- and low-frequency modulation are presented. A hardware prototype of the single-phase inverter was built and tested using resistive, inductive, and nonlinear loads. Experimental results for a 300-W prototype inverter show a 97.4% peak efficiency with a 25 kHz switching frequency. [ABSTRACT FROM AUTHOR]

Traditional model predictive control cost functions, when utilizing long prediction horizons ( $N\geq 10$) in power inverter applications, have demonstrated harmonic performances approaching that of schemes based on offline-generated optimal pulse patterns. However, long prediction horizons often prohibitively increase computational load. A different approach to maximizing harmonic performance is taken in this paper. It is shown that shaping the output voltage spectra using a simple feedback mechanism can significantly reduce the length of the required prediction horizon, facilitating a feasible computational load. When a short-horizon cost function is augmented by the feedback mechanism an excellent tradeoff between harmonic performance and switching loss is achieved, even with a prediction horizon of one. It is also shown that the feedback mechanism can be used to improve input reference tracking. Experimental verification of the proposed modulator is performed on a two-level three-phase inverter. [ABSTRACT FROM AUTHOR]

In this paper, a new carrier-based pulse width modulation (PWM) strategy providing common-mode voltage (CMV) elimination and reduced current ripple in a three-level neutral-point-clamped inverter is introduced. The employed switching sequences are made up of the three zero CMV (ZCMV) vectors, and one among the three vec-tors is applied at two ends of a half-carrier cycle. The output current ripple characteristics pertaining to those switching sequences are investigated. In a carrier cycle, the root-mean-square current ripple minimization is analyzed and an optimal sequence is derived accordingly. The presented PWM scheme results in a considerably reduced current harmonic distortion in a wide modulation region as compared to the two existing ZCMV schemes on the same average switching frequency. Also, an implementation of sawtooth-carrier-based PWM patterns is proposed for further improvement of the harmonic performance. The algorithm requires small computational burden and is straightforward for an online implementation. Simulation and experimental results are both provided to validate the good performance of the proposed PWM method. [ABSTRACT FROM PUBLISHER]

This paper presents an optimized topology for a \text3-\phi three-level inverter with complete elimination of common-mode voltage (CMV). The proposed multilevel inverter (MLI) configuration is realized by modifying a T-structure \text3-\phi inverter. The proposed configuration is an optimized solution with respect to the pulse-width modulation strategy used for CMV elimination. The given three-level inverter structure uses only 16 power semiconductor switches, which is much lower than the existing configurations. A reduced number of power semiconductor devices results in a diminished number of driver circuits, less installation space, and low cost. Further, due to the complete elimination of CMV, the proposed MLI is free from issues such as electromagnetic interference and leakage current with a reduction in filter requirement. The presented topology is also compared with other existing topologies to prove its advantage. It is an optimized solution with respect to the dc bus voltage requirement and the total voltage rating of the devices or the components used in the system. Simulation and experimental results are presented to confirm the capability of the proposed MLI. [ABSTRACT FROM AUTHOR]

As a result of dead-time, device on-state voltage drop, dc bus voltage measurement error, etc., volt-second errors degrade precise control of torque and flux linkage, particularly at low speeds. This is true for deadbeat-direct torque and flux control, which directly manipulates the volt-second vector sourced by inverters, as well as for indirect field oriented control drives. This paper introduces a real-time sensing scheme to measure the motor terminal volt-second vectors for each switching period with negligible phase lag. Based on the volt-second sensing, a model reference adaptive system-based approach is developed to decouple the volt-second errors from inverter nonlinearity, and dc bus voltage fluctuation and measurement error. By delivering an accurate volt-second vector for each switching period, torque and flux control accuracy, self-sensing performance, and parameter estimation accuracy are significantly enhanced. [ABSTRACT FROM AUTHOR]

The impedance-source network converter, utilizing a unique LC network and previously forbidden shoot-through states, provides the ability to buck and boost the input voltage in a single stage. However, the inrush shoot-through current (STC) in startup or transient process might cause undesired current stresses on converter devices. This paper focuses on the STC sensing for an effective inrush current limitation by the combined current sensing technique in the quasi-Z-source inverter. STC and phase currents for the inverter control strategy are obtained simultaneously. No extra hardware is needed and the effects of current sensor bandwidth and duty cycle on the sensing accuracy are analyzed mathematically. The voltage spike gets avoided by integrating the stray inductance into the impedance network. Finally, an STC control loop based on proposed method are embedded in the field-oriented control strategy. The inrush STC and the device current stress in the transient process get suppressed. Simulation and experimental results from a quasi-Z-source inverter validate the feasibility of the proposed methods. [ABSTRACT FROM PUBLISHER]

In signal injection sensorless drives, the injection voltage cannot be reduced under a certain value. The lower limit of the injection voltage is mainly enforced by the inverter nonlinearity that causes distortion of the injection voltage and degradation of the position estimation performance. After analyzing the inverter nonlinearity during the voltage injection, it is revealed that parasitic capacitances of insulated-gate bipolar transistors have positive effects on inverter output linearity and sensorless control. Based on this analysis, this paper proposes a method to reduce the injection voltage by connecting additional capacitors to the output terminals of the inverter. Simulation and experimental results are provided to verify the effectiveness of the proposed idea. In the experiments, using the capacitor-integrated inverter, it is shown that the injection voltage can be reduced by more than half without degrading the position estimation performance. [ABSTRACT FROM AUTHOR]

Distributed energy resources (DERs) are expected to provide ancillary functions including reactive power generation and harmonics compensation. Meanwhile, multilevel inverters and two-level converters with optimal pulsewidth modulation (OPWM) will be commonly used for DERs at high power levels. The challenge is to realize harmonic compensation with limited switching angles. This paper presents an online solution to realize the selective harmonics compensation (SHC), and power generation with DERs. For harmonics compensation, the selective harmonic components in the load current are detected. Then, the harmonic voltages are provided with DERs to cancel out these detected components. Since the power converter is requested to realize both harmonics filtering and power generation, limitations on harmonics compensation at the given power are discussed. Power hardware-in-the-loop-based online verifications are shown at the end of the paper. [ABSTRACT FROM AUTHOR]

The Z-source inverter (ZSI) employs an LC impedance network between the main inverter bridge and the power source. The unique feature of the ZSI is that it can operate either in buck or boost mode with a wide range of obtainable output voltages from a given input voltage. This topology also exhibits better electromagnetic-interference noise immunity when compared to a traditional voltage-source inverter (VSI). However, the LC impedance network of ZSI significantly increases the size and cost of the power converter and can make it unsuitable for low-power applications. This paper proposes a novel topology called switched boost inverter (SBI) which exhibits similar advantages of ZSI with lower number of passive components and more active components compared to ZSI. The steady-state and small-signal analyses of SBI, along with its pulsewidth modulation (PWM) control strategies, have been discussed in this paper. This paper also presents a comparison of SBI and ZSI with the same input and output parameters. The theoretical analysis given in this paper has been validated using a laboratory prototype of SBI, and the experimental results are presented for verification. The experimental harmonic spectrum of the inverter's output voltage with the proposed PWM technique is also plotted and compared with that of a traditional VSI. All the experimental results show good correlation between theory and experiments. [ABSTRACT FROM PUBLISHER]

Neutral-point (NP)-clamped three-level inverter, which is a widely used topology of multilevel converters, suffers from the NP voltage drift as its main technical drawback. The nearest-three-virtual-vector (\NTV^2) modulation method can control the NP voltage balance for any load over the full range of inverter output voltage. However, compared with the nearest-three-vector (NTV) modulation method, \NTV^2 increases the switching frequency. This paper combines \NTV^2 with NTV, and the two methods are used alternately in a fundamental cycle. The duty-cycle coefficients of the redundant small vectors are analyzed to explore the intervals where NTV can control the NP voltage balance in a fundamental cycle. The proportional parameter, which represents the combination of the two methods in hybrid space vector pulsewidth modulation, can be selected to achieve a high-performance NP balance control and low switching frequency. The steady- and transient-state behaviors of the proposed strategy are analyzed in this paper. The experimental results verify the validity of the proposed strategy. [ABSTRACT FROM PUBLISHER]

In this paper, an immune algorithm (IA) is developed for optimization of the harmonic performance of a three-phase inverter under the space-vector pulsewidth-modulation (SVPWM) control strategy. The presented algorithm employs the immune approach as the search method for finding the best optimal control vectors and action time of the three-phase inverter. As a result, the optimal control vectors and action time are calculated to minimize the objective function of the weighted total harmonic distortion of the output voltage waveforms. In addition, an experimental platform based on DSP and field-programmable gate array is built. This paper provides a detailed performance analysis of the method with comparison to the conventional SVPWM. The simulation and experimental results verify the superiority of the best control sequences generated by IA compared with the existing conventional control strategies. [ABSTRACT FROM PUBLISHER]

A new pulse width modulation (PWM) strategy which is an alternative approach of the discontinuous PWM (DPWM) for a three-level neutral-point-clamped (NPC) inverter is developed and presented in this paper. The proposed PWM scheme not only takes advantage of the special properties available in NPC inverters, but also reduces the switching loss of the inverter along with an inherent neutral point (NP) voltage control. Based on a circuit-level decoupling concept, the NPC inverter can be decoupled into two three-level Buck converters in every defined operating section, and thereby the controller design can be simplified. The salient features of the proposed scheme, as compared with the existing carrier-based DPWM strategies, are: 1) its reduced computational processing time, 2) its capability to balance the dc-link voltage without any additional control, and 3) its reduced complexity, e.g., only one carrier wave needed for pulse width modulating. Same as a space-vector modulation, the maximum modulation index, 1.1547, can be attainable by the proposed scheme. Moreover, compared to conventional continuous sinusoidal PWM, using this technique proposed here, the switching losses of the devices can be reduced by one third. In order to explain the operation of this topology properly, the decoupling principle including the driving signal synthesis and the NP potential variation are analyzed in detail in this paper. Finally, the viability and performance of the proposed modulation scheme are shown through simulation and experimental results in a laboratory prototype. [ABSTRACT FROM PUBLISHER]

This paper discusses the implementation of level-shifted and phase-shifted carrier-based modulation methods, in conjunction with a multiphase open-end winding drive topology. The considered drive is supplied using two five-phase two-level voltage source inverters (VSIs), with input provided from two isolated supplies of equal dc voltages. The topology is known to yield the same space-vector pattern as a corresponding three-level inverter in single-sided supply mode. It is shown in this paper that, with the application of a simple logic, the same phase voltage waveforms result as those obtainable with the appropriate carrier-based modulation scheme applied to the three-level VSI in single-sided supply mode. While the outcomes of the modulation techniques are the same, the open-end winding topology offers certain advantages, such as modularity and absence of capacitor voltage balancing requirements. The analysis is conducted for selected modulation methods using voltage and current waveforms, spectra Fast Fourier Transform (FFT), and total harmonic distortion as figures of merit. Theoretical considerations are verified by means of simulation and experimental results. [ABSTRACT FROM PUBLISHER]