Search

Metal halide perovskites are promising light absorbers for multijunction photovoltaic applications because of their remarkable bandgap tunability, achieved through compositional mixing on the halide site. However, poor energy‐level alignment at the interface between wide‐bandgap mixed‐halide perovskites and charge‐extraction layers still causes significant losses in solar‐cell performance. Here, the origin of such losses is investigated, focusing on the energy‐level misalignment between the valence band maximum and the highest occupied molecular orbital (HOMO) for a commonly employed combination, FA0.83Cs0.17Pb(I1‐xBrx)3 with bromide content x ranging from 0 to 1, and poly[bis(4‐phenyl)(2,4,6‐trimethylphenyl)amine] (PTAA). A combination of time‐resolved photoluminescence spectroscopy and numerical modeling of charge‐carrier dynamics reveals that open‐circuit voltage (VOC) losses associated with a rising energy‐level misalignment derive from increasing accumulation of holes in the HOMO of PTAA, which then subsequently recombine non‐radiatively across the interface via interfacial defects. Simulations assuming an ideal choice of hole‐transport material to pair with FA0.83Cs0.17Pb(I1‐xBrx)3 show that such VOC losses originating from energy‐level misalignment can be reduced by up to 70 mV. These findings highlight the urgent need for tailored charge‐extraction materials exhibiting improved energy‐level alignment with wide‐bandgap mixed‐halide perovskites to enable solar cells with improved power conversion efficiencies. [ABSTRACT FROM AUTHOR]

Two dimensional/three‐dimensional (2D/3D) metal halide perovskite heterostructures have attracted great interest in photovoltaic and light‐emitting diode (LEDs) applications. In both, their implementation results in an improvement in device efficiency yet the understanding of these heterostructures remains incomplete. In this work the role of organic cations, essential for the formation of 2D perovskite structures is unraveled, in a range of metal halide perovskite heterostructures. These heterostructures are used to fabricate efficient green perovskite LEDs and a strong dependence between cation content and device performance is shown. The crystal structure, charge‐carrier transport and dynamics, and the electronic structure of these heterostructures are studied and it is shown that the presence of crystalline 2D perovskite inhibits electron injection and ultimately lowers device performance. This work highlights the importance of optimizing the composition of these heterostructures in ensuring optimal device performance across all parameters and suggests that developing routes to inject charge‐carriers directly into 2D perovskite structures will be important in ensuring the continued development of perovskite LEDs based on these heterostructures. [ABSTRACT FROM AUTHOR]

Metal‐halide perovskites have proven to be a versatile group of semiconductors for optoelectronic applications, with ease of bandgap tuning and stability improvements enabled by halide and cation mixing. However, such compositional variations can be accompanied by significant changes in their charge‐carrier transport and recombination regimes that are still not fully understood. Here, a novel combinatorial technique is presented to disentangle such dynamic processes over a wide range of temperatures, based on transient free‐space, high‐frequency microwave conductivity and photoluminescence measurements conducted simultaneously in situ. Such measurements are used to reveal and contrast the dominant charge‐carrier recombination pathways for a range of key compositions: prototypical methylammonium lead iodide perovskite (MAPbI3), the stable mixed formamidinium‐caesium lead‐halide perovskite FA0.83Cs0.17PbBr0.6I2.4 targeted for photovoltaic tandems with silicon, and fully inorganic wide‐bandgap CsPbBr3 aimed toward light sources and X‐ray detector applications. The changes in charge‐carrier dynamics in FA0.83Cs0.17PbBr0.6I2.4 across temperatures are shown to be dominated by radiative processes, while those in MAPbI3 are governed by energetic disorder at low temperatures, low‐bandgap minority‐phase inclusions around the phase transition, and non‐radiative processes at room temperature. In contrast, CsPbBr3 exhibits significant charge‐carrier trapping at low and high temperatures, highlighting the need for improvement of material processing techniques for wide‐bandgap perovskites. [ABSTRACT FROM AUTHOR]

Metal halide perovskite semiconductors have shown great performance in solar cells, and including an excess of lead iodide (PbI2) in the thin films, either as mesoscopic particles or embedded domains, often leads to improved solar cell performance. Atomic resolution scanning transmission electron microscope micrographs of formamidinium lead iodide (FAPbI3) perovskite films reveal the FAPbI3:PbI2 interface to be remarkably coherent. It is demonstrated that such interface coherence is achieved by the PbI2 deviating from its common 2H hexagonal phase to form a trigonal 3R polytype through minor shifts in the stacking of the weakly van‐der‐Waals‐bonded layers containing the near‐octahedral units. The exact crystallographic interfacial relationship and lattice misfit are revealed. It is further shown that this 3R polytype of PbI2 has similar X‐ray diffraction (XRD) peaks to that of the perovskite, making XRD‐based quantification of the presence of PbI2 unreliable. Density functional theory demonstrates that this interface does not introduce additional electronic states in the bandgap, making it electronically benign. These findings explain why a slight PbI2 excess during perovskite film growth can help template perovskite crystal growth and passivate interfacial defects, improving solar cell performance. [ABSTRACT FROM AUTHOR]

Owing to the bandgap‐bowing effect, mixed lead‐tin halide perovskites provide ideal bandgaps for the bottom subcell of all‐perovskite tandem photovoltaic devices that offer fundamentally elevated power‐conversion efficiencies. However, these materials suffer from degradation in ambient air, which worsens their optoelectronic properties and hinders their usability for photovoltaic applications. Such degradation pathways are not yet fully understood, especially for the perovskites in the middle of the APbxSn1‐xI3 solid solution line, which offer the narrowest bandgaps across the range. This study unravels the degradation mechanisms of APbxSn1‐xI3 perovskites, reporting clear differences between mixed lead‐tin (x = 0.5) and tin‐only (x = 0) perovskites. The dynamic optoelectronic properties, electronic structure, crystal structure, and decomposition products of the perovskite thin films are examined in situ during air exposure. Both perovskite compositions suffer from the formation of defects over the timescale of hours, as indicated by a significant reduction in their charge‐carrier diffusion lengths. For tin‐only perovskite, degradation predominantly causes the formation of energetically shallow tin vacancies and hole doping. However, for mixed lead‐tin perovskite, deep trap states are formed that significantly accelerate charge‐carrier recombination, yet leave mobilities relatively unaffected. These findings highlight the need for passivation strategies tailored specifically to mixed lead‐tin iodide perovskites. [ABSTRACT FROM AUTHOR]

Mixed lead‐tin (Pb:Sn) halide perovskites are promising absorbers with narrow‐bandgaps (1.25–1.4 eV) suitable for high‐efficiency all‐perovskite tandem solar cells. However, solution processing of optimally thick Pb:Sn perovskite films is notoriously difficult in comparison with their neat‐Pb counterparts. This is partly due to the rapid crystallization of Sn‐based perovskites, resulting in films that have a high degree of roughness. Rougher films are harder to coat conformally with subsequent layers using solution‐based processing techniques leading to contact between the absorber and the top metal electrode in completed devices, resulting in a loss of VOC, fill factor, efficiency, and stability. Herein, this study employs a non‐continuous layer of alumina nanoparticles distributed on the surface of rough Pb:Sn perovskite films. Using this approach, the conformality of the subsequent electron‐transport layer, which is only tens of nanometres in thickness is improved. The overall maximum‐power‐point‐tracked efficiency improves by 65% and the steady‐state VOC improves by 28%. Application of the alumina nanoparticles as an interfacial buffer layer also results in highly reproducible Pb:Sn solar cell devices while simultaneously improving device stability at 65 °C under full spectrum simulated solar irradiance. Aged devices show a six‐fold improvement in stability over pristine Pb:Sn devices, increasing their lifetime to 120 h. [ABSTRACT FROM AUTHOR]

Metal halide perovskite (MHP) semiconductors have driven a revolution in optoelectronic technologies over the last decade, in particular for high‐efficiency photovoltaic applications. Low‐dimensional MHPs presenting electronic confinement have promising additional prospects in light emission and quantum technologies. However, the optimisation of such applications requires a comprehensive understanding of the nature of charge carriers and their transport mechanisms. This study employs a combination of ultrafast optical and terahertz spectroscopy to investigate phonon energies, charge‐carrier mobilities, and exciton formation in 2D (PEA)2PbI4 and (BA)2PbI4 (where PEA is phenylethylammonium and BA is butylammonium). Temperature‐dependent measurements of free charge‐carrier mobilities reveal band transport in these strongly confined semiconductors, with surprisingly high in‐plane mobilities. Enhanced charge‐phonon coupling is shown to reduce charge‐carrier mobilities in (BA)2PbI4 with respect to (PEA)2PbI4. Exciton and free charge‐carrier dynamics are disentangled by simultaneous monitoring of transient absorption and THz photoconductivity. A sustained free charge‐carrier population is observed, surpassing the Saha equation predictions even at low temperature. These findings provide new insights into the temperature‐dependent interplay of exciton and free‐carrier populations in 2D MHPs. Furthermore, such sustained free charge‐carrier population and high mobilities demonstrate the potential of these semiconductors for applications such as solar cells, transistors, and electrically driven light sources. [ABSTRACT FROM AUTHOR]

In this work, we couple theoretical and experimental approaches to understand and reduce the losses of wide bandgap Br-rich perovskite pin devices at open-circuit voltage (VOC) and short-circuit current (JSC) conditions. A mismatch between the internal quasi-Fermi level splitting (QFLS) and the external VOC is detrimental for these devices. We demonstrate that modifying the perovskite top-surface with guanidinium-Br and imidazolium-Br forms a low-dimensional perovskite phase at the n-interface, suppressing the QFLS-VOC mismatch, and boosting the VOC. Concurrently, the use of an ionic interlayer or a self-assembled monolayer at the p-interface reduces the inferred field screening induced by mobile ions at JSC, promoting charge extraction and raising the JSC. The combination of the n- and p-type optimizations allows us to approach the thermodynamic potential of the perovskite absorber layer, resulting in 1 cm2 devices with performance parameters of VOCs up to 1.29 V, fill factors above 80% and JSCs up to 17 mA/cm2, in addition to a thermal stability T80 lifetime of more than 3500 h at 85 °C. A mismatch between quasi-Fermi level splitting and open-circuit voltage is detrimental to wide bandgap perovskite pin solar cells. Here, through theoretical and experimental approaches, the authors optimize n- and p-type interfaces to achieve open-circuit voltage of 1.29 V and T80 of 3500 h at 85 °C. [ABSTRACT FROM AUTHOR]

Mixed‐halide perovskites offer ideal bandgaps for tandem solar cells, but photoinduced halide segregation compromises photovoltaic device performance. This study explores the influence of a hole‐transport layer, necessary for a full device, by monitoring halide segregation through in situ, concurrent X‐ray diffraction and photoluminescence measurements to disentangle compositional and optoelectronic changes. This work demonstrates that top coating FA0.83Cs0.17Pb(Br0.4I0.6)3 perovskite films with a poly(triaryl)amine (PTAA) hole‐extraction layer surprisingly leads to suppression of halide segregation because photogenerated charge carriers are rapidly trapped at interfacial defects that do not drive halide segregation. However, the generation of iodide‐enriched regions near the perovskite/PTAA interface enhances hole back‐transfer from the PTAA layer through improved energy level offsets, increasing radiative recombination losses. It is further found that while passivation with a piperidinium salt slows halide segregation in perovskite films, the addition of a PTAA top‐coating accelerates such effects, elucidating the specific nature of trap types that are able to drive the halide segregation process. This work highlights the importance of selective passivation techniques for achieving efficient and stable wide‐bandgap perovskite photovoltaic devices. [ABSTRACT FROM AUTHOR]

Mixed halide perovskites can provide optimal bandgaps for tandem solar cells which are key to improved cost-efficiencies, but can still suffer from detrimental illumination-induced phase segregation. Here we employ optical-pump terahertz-probe spectroscopy to investigate the impact of halide segregation on the charge-carrier dynamics and transport properties of mixed halide perovskite films. We reveal that, surprisingly, halide segregation results in negligible impact to the THz charge-carrier mobilities, and that charge carriers within the I-rich phase are not strongly localised. We further demonstrate enhanced lattice anharmonicity in the segregated I-rich domains, which is likely to support ionic migration. These phonon anharmonicity effects also serve as evidence of a remarkably fast, picosecond charge funnelling into the narrow-bandgap I-rich domains. Our analysis demonstrates how minimal structural transformations during phase segregation have a dramatic effect on the charge-carrier dynamics as a result of charge funnelling. We suggest that because such enhanced recombination is radiative, performance losses may be mitigated by deployment of careful light management strategies in solar cells. Phase segregation in mixed halide perovskite is known to alter the optoelectronic properties, but how it affects charge carriers is not clear. Here, the authors use THz spectroscopy to reveal that high carrier mobilities are well preserved, while recombination dynamics is affected by charge funnelling upon segregation. [ABSTRACT FROM AUTHOR]

Mixed tin‐lead halide perovskites are promising low‐bandgap absorbers for all‐perovskite tandem solar cells that offer higher efficiencies than single‐junction devices. A significant barrier to higher performance and stability is the ready oxidation of tin, commonly mitigated by various additives whose impact is still poorly understood for mixed tin‐lead perovskites. Here, the effects of the commonly used SnF2 additive are revealed for FA0.83Cs0.17SnxPb1−xI3 perovskites across the full compositional lead‐tin range and SnF2 percentages of 0.1–20% of precursor tin content. SnF2 addition causes a significant reduction in the background hole density associated with tin vacancies, yielding longer photoluminescence lifetimes, decreased energetic disorder, reduced Burstein–Moss shifts, and higher charge‐carrier mobilities. Such effects are optimized for SnF2 addition of 1%, while for 5% SnF2 and above, additional nonradiative recombination pathways begin to appear. It is further found that the addition of SnF2 reduces a tetragonal distortion in the perovskite structure deriving from the presence of tin vacancies that cause strain, particularly for high tin content. The optical phonon response associated with inorganic lattice vibrations is further explored, exhibiting a shift to higher frequency and significant broadening with increasing tin fraction, in accordance with lower effective atomic metal masses and shorter phonon lifetimes. [ABSTRACT FROM AUTHOR]

Trap‐related charge‐carrier recombination fundamentally limits the performance of perovskite solar cells and other optoelectronic devices. While improved fabrication and passivation techniques have reduced trap densities, the properties of trap states and their impact on the charge‐carrier dynamics in metal‐halide perovskites are still under debate. Here, a unified model is presented of the radiative and nonradiative recombination channels in a mixed formamidinium‐cesium lead iodide perovskite, including charge‐carrier trapping, de‐trapping and accumulation, as well as higher‐order recombination mechanisms. A fast initial photoluminescence (PL) decay component observed after pulsed photogeneration is demonstrated to result from rapid localization of free charge carriers in unoccupied trap states, which may be followed by de‐trapping, or nonradiative recombination with free carriers of opposite charge. Such initial decay components are shown to be highly sensitive to remnant charge carriers that accumulate in traps under pulsed‐laser excitation, with partial trap occupation masking the trap density actually present in the material. Finally, such modelling reveals a change in trap density at the phase transition, and disentangles the radiative and nonradiative charge recombination channels present in FA0.95Cs0.05PbI3, accurately predicting the experimentally recorded PL efficiencies between 50 and 295 K, and demonstrating that bimolecular recombination is a fully radiative process. [ABSTRACT FROM AUTHOR]

The production of highly efficient single‐ and multijunction metal halide perovskite (MHP) solar cells requires careful optimization of the optical and electrical properties of these devices. Here, precise control of CH3NH3PbI3 perovskite layers is demonstrated in solar cell devices through the use of dual source coevaporation. Light absorption and device performance are tracked for incorporated MHP films ranging from ≈67 nm to ≈1.4 µm thickness and transfer‐matrix optical modeling is utilized to quantify optical losses that arise from interference effects. Based on these results, a device with 19.2% steady‐state power conversion efficiency is achieved through incorporation of a perovskite film with near‐optimum predicted thickness (≈709 nm). Significantly, a clear signature of photon reabsorption is observed in perovskite films that have the same thickness (≈709 nm) as in the optimized device. Despite the positive effect of photon recycling associated with photon reabsorption, devices with thicker (>750 nm) MHP layers exhibit poor performance owing to competing nonradiative charge recombination in a "dead‐volume" of MHP. Overall, these findings demonstrate the need for fine control over MHP thickness to achieve the highest efficiency cells, and accurate consideration of photon reabsorption, optical interference, and charge transport properties. [ABSTRACT FROM AUTHOR]

Mixed‐halide perovskites are essential for use in all‐perovskite or perovskite–silicon tandem solar cells due to their tunable bandgap. However, trap states and halide segregation currently present the two main challenges for efficient mixed‐halide perovskite technologies. Here photoluminescence techniques are used to study trap states and halide segregation in full mixed‐halide perovskite photovoltaic devices. This work identifies three distinct defect species in the perovskite material: a charged, mobile defect that traps charge‐carriers in the perovskite, a charge‐neutral defect that induces halide segregation, and a charged, mobile defect that screens the perovskite from external electric fields. These three defects are proposed to be MA+ interstitials, crystal distortions, and halide vacancies and/or interstitials, respectively. Finally, external quantum efficiency measurements show that photoexcited charge‐carriers can be extracted from the iodide‐rich low‐bandgap regions of the phase‐segregated perovskite formed under illumination, suggesting the existence of charge‐carrier percolation pathways through grain boundaries where phase‐segregation may occur. [ABSTRACT FROM AUTHOR]

Organohalide perovskites have emerged as promising light-sensing materials because of their superior optoelectronic properties and low-cost processing methods. Recently, perovskite-based photodetectors have successfully been demonstrated as both broadband and narrowband varieties. However, the photodetection bandwidth in perovskite-based photodetectors has so far been limited to the near-infrared regime owing to the relatively wide band gap of hybrid organohalide perovskites. In particular, short-wavelength infrared photodiodes operating beyond 1 µm have not yet been realized with organohalide perovskites. In this study, narrow band gap organic dyes are combined with hybrid perovskites to form composite films as active photoresponsive layers. Tuning the dye loading allows for optimization of the spectral response characteristics and excellent charge-carrier mobilities near 11 cm2 V−1 s−1, suggesting that these composites combine the light-absorbing properties or IR dyes with the outstanding charge-extraction characteristics of the perovskite. This study demonstrates the first perovskite photodiodes with deep near-infrared and short-wavelength infrared response that extends as far as 1.6 µm. All devices are solution-processed and exhibit relatively high responsivity, low dark current, and fast response at room temperature, making this approach highly attractive for next-generation light-detection techniques. [ABSTRACT FROM AUTHOR]

Traps limit the photovoltaic efficiency and affect the charge transport of optoelectronic devices based on hybrid lead halide perovskites. Understanding the nature and energy scale of these trap states is therefore crucial for the development and optimization of solar cell and laser technology based on these materials. Here, the low-temperature photoluminescence of formamidinium lead triiodide (HC(NH2)2PbI3) is investigated. A power-law time dependence in the emission intensity and an additional low-energy emission peak that exhibits an anomalous relative Stokes shift are observed. Using a rate-equation model and a Monte Carlo simulation, it is revealed that both phenomena arise from an exponential trap-density tail with characteristic energy scale of ≈3 meV. Charge-carrier recombination from sites deep within the tail is found to cause emission with energy downshifted by up to several tens of meV. Hence, such phenomena may in part be responsible for open-circuit voltage losses commonly observed in these materials. In this high-quality hybrid perovskite, trap states thus predominantly comprise a continuum of energetic levels (associated with disorder) rather than discrete trap energy levels (associated, e.g., with elemental vacancies). Hybrid perovskites may therefore be viewed as classic semiconductors whose band-structure picture is moderated by a modest degree of energetic disorder. [ABSTRACT FROM AUTHOR]

The article offers information on the hysteresis in the current–voltage characteristics of vapor‐deposited perovskite solar cells. Topics discussed include usage of interface engineering in producing crystalline perovskite material; information on planar heterojunction solar cells; and the chemical vapor deposition process.

Highest reported efficiency cesium lead halide perovskite solar cells are realized by tuning the bandgap and stabilizing the black perovskite phase at lower temperatures. CsPbI2Br is employed in a planar architecture device resulting in 9.8% power conversion efficiency and over 5% stabilized power output. Offering substantially enhanced thermal stability over their organic based counterparts, these results show that all‐inorganic perovskites can represent a promising next step for photovoltaic materials. [ABSTRACT FROM AUTHOR]

The photoluminescence, transmittance, charge-carrier recombination dynamics, mobility, and diffusion length of CH3NH3PbI3 are investigated in the temperature range from 8 to 370 K. Profound changes in the optoelectronic properties of this prototypical photovoltaic material are observed across the two structural phase transitions occurring at 160 and 310 K. Drude-like terahertz photoconductivity spectra at all temperatures above 80 K suggest that charge localization effects are absent in this range. The monomolecular charge-carrier recombination rate generally increases with rising temperature, indicating a mechanism dominated by ionized impurity mediated recombination. Deduced activation energies Ea associated with ionization are found to increase markedly from the room-temperature tetragonal ( Ea ≈ 20 meV) to the higher-temperature cubic ( Ea ≈ 200 meV) phase adopted above 310 K. Conversely, the bimolecular rate constant decreases with rising temperature as charge-carrier mobility declines, while the Auger rate constant is highly phase specific, suggesting a strong dependence on electronic band structure. The charge-carrier diffusion length gradually decreases with rising temperature from about 3 μm at −93 °C to 1.2 μm at 67 °C but remains well above the optical absorption depth in the visible spectrum. These results demonstrate that there are no fundamental obstacles to the operation of cells based on CH3NH3PbI3 under typical field conditions. [ABSTRACT FROM AUTHOR]

Organic-inorganic metal halide perovskite solar cells have emerged in the past few years to promise highly efficient photovoltaic devices at low costs. Here, temperature-sensitive core-shell Ag@TiO2 nanoparticles are successfully incorporated into perovskite solar cells through a low-temperature processing route, boosting the measured device efficiencies up to 16.3%. Experimental evidence is shown and a theoretical model is developed which predicts that the presence of highly polarizable nanoparticles enhances the radiative decay of excitons and increases the reabsorption of emitted radiation, representing a novel photon recycling scheme. The work elucidates the complicated subtle interactions between light and matter in plasmonic photovoltaic composites. Photonic and plasmonic schemes such as this may help to move highly efficient perovskite solar cells closer to the theoretical limiting efficiencies. [ABSTRACT FROM AUTHOR]

The article discusses a study which examines the flexible platform of perovskite semiconductors for wavelength-selective sensing and colour imaging. Topics include the production of colour imaging arrays, the comparison between photodiodes and solar cells, and control of switch off and onset wavelengths of photodiodes.

Organic semiconductors are commonly used as charge-extraction layers in metal-halide perovskite solar cells. However, parasitic light absorption in the sun-facing front molecular layer, through which sun light must propagate before reaching the perovskite layer, may lower the power conversion efficiency of such devices. Here, we show that such losses may be eliminated through efficient excitation energy transfer from a photoexcited polymer layer to the underlying perovskite. Experimentally observed energy transfer between a range of different polymer films and a methylammonium lead iodide perovskite layer was used as basis for modelling the efficacy of the mechanism as a function of layer thickness, photoluminescence quantum efficiency and absorption coefficient of the organic polymer film. Our findings reveal that efficient energy transfer can be achieved for thin (≤10 nm) organic charge-extraction layers exhibiting high photoluminescence quantum efficiency. We further explore how the morphology of such thin polymer layers may be affected by interface formation with the perovskite. The performance of perovskite solar cells can be limited by light absorption loss in organic charge extraction layers, through which sun light must propagate before reaching the perovskite. Here, the authors demonstrate that efficient energy transfer to the perovskite layer from a thin organic layer is able to eliminate this parasitic loss. [ABSTRACT FROM AUTHOR]

Halide perovskites are currently one of the most heavily researched emerging photovoltaic materials. Despite achieving remarkable power conversion efficiencies, perovskite solar cells have not yet achieved their full potential, with the interfaces between the perovskite and the charge‐selective layers being where most recombination losses occur. In this study, a fluorinated ionic liquid (IL) is employed to modify the perovskite/SnO2 interface. Using Kelvin probe and photoelectron spectroscopy measurements, it is shown that depositing the perovskite onto an IL‐treated substrate results in the crystallization of a perovskite film which has a more n‐type character, evidenced by a decrease of the work function and a shift of the Fermi level toward the conduction band. Photoluminescence spectroscopy and time‐resolved microwave conductivity are used to investigate the optoelectronic properties of the perovskite grown on neat and IL‐modified surfaces and it is found that the modified substrate yields a perovskite film which exhibits an order of magnitude lower trap density than the control. When incorporated into solar cells, this interface modification results in a reduction in the current–voltage hysteresis and an improvement in device performance, with the best performing devices achieving steady‐state PCEs exceeding 20%. [ABSTRACT FROM AUTHOR]

The efficiency and longevity of metal-halide perovskite solar cells are typically dictated by nonradiative defect-mediated charge recombination. In this work, we demonstrate a vapor-based amino-silane passivation that reduces photovoltage deficits to around 100 millivolts (>90% of the thermodynamic limit) in perovskite solar cells of bandgaps between 1.6 and 1.8 electron volts, which is crucial for tandem applications. A primary-, secondary-, or tertiary-amino–silane alone negatively or barely affected perovskite crystallinity and charge transport, but amino-silanes that incorporate primary and secondary amines yield up to a 60-fold increase in photoluminescence quantum yield and preserve long-range conduction. Amino-silane–treated devices retained 95% power conversion efficiency for more than 1500 hours under full-spectrum sunlight at 85°C and open-circuit conditions in ambient air with a relative humidity of 50 to 60%. [ABSTRACT FROM AUTHOR]

Longevity has been a long-standing concern for hybrid perovskite photovoltaics. We demonstrate high-resilience positive-intrinsic-negative perovskite solar cells by incorporating a piperidinium-based ionic compound into the formamidinium-cesium lead-trihalide perovskite absorber. With the bandgap tuned to be well suited for perovskite-on-silicon tandem cells, this piperidinium additive enhances the open-circuit voltage and cell efficiency. This additive also retards compositional segregation into impurity phases and pinhole formation in the perovskite absorber layer during aggressive aging. Under full-spectrum simulated sunlight in ambient atmosphere, our unencapsulated and encapsulated cells retain 80 and 95% of their peak and post-burn-in efficiencies for 1010 and 1200 hours at 60° and 85°C, respectively. Our analysis reveals detailed degradation routes that contribute to the failure of aged cells. [ABSTRACT FROM AUTHOR]

Hybrid metal-halide perovskites are promising new materials for use in solar cells; however, their chemical stability in the presence of moisture remains a significant drawback. Quasi two-dimensional (2D) perovskites that incorporate hydrophobic organic interlayers offer improved resistance to degradation by moisture, currently still at the cost of overall cell efficiency. To elucidate the factors affecting the optoelectronic properties of these materials, we have investigated the charge transport properties and crystallographic orientation of mixed methylammonium (MA)-phenylethylammonium (PEA) lead iodide thin films as a function of the MA-to-PEA ratio and, thus, the thickness of the "encapsulated" MA lead-halide layers. We find that monomolecular charge-carrier recombination rates first decrease with increasing PEA fraction, most likely as a result of trap passivation, but then increase significantly as excitonic effects begin to dominate for thin confined layers. Bimolecular and Auger recombination rate constants are found to be sensitive to changes in electronic confinement, which alters the density of states for electronic transitions. We demonstrate that effective charge-carrier mobilities remain remarkably high (near 10 cm²V−1s−1) for intermediate PEA content and are enhanced for preferential orientation of the conducting lead iodide layers along the probing electric field. The trade-off between trap reduction, electronic confinement, and layer orientation leads to calculated charge-carrier diffusion lengths reaching a maximum of 2.5 μm for intermediate PEA content (50%). [ABSTRACT FROM AUTHOR]

Metal halide perovskite photovoltaic cells could potentially boost the efficiency of commercial silicon photovoltaic modules from ~20 toward 30% when used in tandem architectures. An optimum perovskite cell optical band gap of ~1.75 electron volts (eV) can be achieved by varying halide composition, but to date, such materials have had poor photostability and thermal stability. Here we present a highly crystalline and compositionally photostable material, [HC(NH2)2]0.83Cs0.17Pb(l0.6Br0.4)3, with an optical band gap of ~1.74 eV, and we fabricated perovskite cells that reached open-circuit voltages of 1.2 volts and power conversion efficiency of over 17% on small areas and 14.7% on 0.715 cm² cells. By combining these perovskite cells with a 19%-efficient silicon cell, we demonstrated the feasibility of achieving >25%-efficient four-terminal tandem cells. [ABSTRACT FROM AUTHOR]

The performance of perovskite solar cells has been progressing over the past few years and efficiency is likely to continue to increase. However, a negative aspect for the integration of perovskite solar cells in the built environment is that the color gamut available in these materials is very limited and does not cover the green-to-blue region of the visible spectrum, which has been a big selling point for organic photovoltaics. Here, we integrate a porous photonic crystal (PC) scaffold within the photoactive layer of an opaque perovskite solar cell following a bottom-up approach employing inexpensive and scalable liquid processing techniques. The photovoltaic devices presented herein show high efficiency with tunable color across the visible spectrum. This now imbues the perovskite solar cells with highly desirable properties for cladding in the built environment and encourages design of sustainable colorful buildings and iridescent electric vehicles as future power generation sources. [ABSTRACT FROM AUTHOR]

The article discusses Atomic-scale microstructure of metal halide perovskite. Topics include hybrid metal halide perovskites are highly favorable materials for efficient photovoltaic and optoelectronic applications; Atomic-resolution transmission electron microscopy is well suited to provide new insights but is challenging because of the highly beam-sensitive nature of hybrid perovskites.