Search

This paper focuses on studying and simulating a GaAs1-xPx/Si1-yGey/Ge triple-junction solar cell structure. First, the strain and the bandgap energy associated to the SiGe layer have been studied. The optimal germanium concentration is 0.88 with a strain around 0.45%. Then, the phosphor concentration effect on the strain and the bandgap energy of the upper layer GaAs1-xPx/Si0.12Ge0.88 has been optimized. At room temperature, the optimal output parameter reach Jsc=34.41mA/cm², Voc=1.27V, FF=88.42% and =38.45% for an absorber thickness of 4.5µm and x=0.47, with a strain that doesn't exceed 1.5%. This study has enabled us to design a high-efficiency, low cost 3J solar cell. [ABSTRACT FROM AUTHOR]

This paper focuses on the simulation and optimization of electrical and optical properties such as current density-voltage (J-V ) , external quantum efficiency (EQE) and the photoluminescence spectra (PL) of InSb/GaAs quantum dot solar cell (QDSC). The InSb QDs have been inserted in the intrinsic region of p-i-n GaAs solar cell. Our results have been shown that 30 InSb/GaAs QD layers provide a relative enhancement of 22.35% and 29.30% of the short-circuit current and the efficiency, respectively. With the same number of the QD layers, the absorption range edge of low energy photons has been extended from 900 to 1400 nm. The electrical features obtained for InSb/GaAs QDSC have been compared with those obtained for InAs/GaAs QDSC in goal to show the better structure. The PL spectra has been also compared with experimental result for the same structure. Moreover, the QDSC has been optimized with respect to the thickness of QDs. The optimal conversion efficiency of 10 QD layers is improved from 14.85% to 18.30% by increasing the thickness of the QDs from 5 nm to 20 nm. [ABSTRACT FROM AUTHOR]

This work deals with the modeling and optimization of the CuInGaSe/CdS based structure for photovoltaic applications. We took into consideration the effect of the gallium concentration and the temperature on the strain, band gap energy, absorption and efficiency of the structure. It has been demonstrated that increasing the gallium concentration increases the ban gap energy, while increasing temperature decreases it. These two parameters vary the efficiency significantly. For x = 30% and T = 300 K, the band gap energy is equal to 1.15 eV with a deformation of 0.5% and efficiency around 20%. We have also found that at this value of the band gap energy the structure absorbs most of the incident photons. Then to achieve a reliable cell based on CuInGaSe/CdS it is adequate to find a compromise between the gallium concentration in the alloy, the temperature and the strain. [ABSTRACT FROM AUTHOR]

A combination of a Copper Indium Gallium Selenide (CIGS) and Silicon (Si) layer has been recognized as an excellent choice for producing heterojunction based solar cells with improved efficiency and low cost processing techniques. The quaternary compound CIGS and silicon (Si) regions exhibit a lattice mismatch of about 5%, which induces a strain and impacts the electronic characteristics of the CIGS/Si heterojunction solar cell. A new viewpoint suggests the integration of a silicon germanium (Si 1-y Ge y) layer in the CIGS/Si region to reduce the impact of lattice mismatch. The objective of this study is to investigate how different gallium and germanium concentrations (x Ga and y Ge) affect the following factors: lattice mismatch (ε) , critical thickness (h c) and absorption coefficient (α)of CIGS/SiGe based solar cells. It also aims to analyze how these concentrations impact the primary parameters used to evaluate solar cell performance such as external quantum efficiency, short circuit current density, fill factor, open circuit voltage and conversion efficiency. The simulation results agree well with the existing theoretical and experimental literature data, confirming the suitability of the physical characteristics employed in this numerical study. By tuning the concentrations of Gallium and Germanium, it is feasible to attain an efficiency of 24% owing to the lattice compensation phenomenon in Si 1-y Ge y layers. These findings hold significant implications for the development and advancement of solar cell technology, as well as for enhancing their conversion efficiency and commercialization. • A strain-compensated CIGS/Si structure was achieved by adding SiGe layer. • The incorporation of SiGe improves the absorbance and EQE of the CIGS solar cell. • The improvement of the solar performances of the CIGS is ensured by the SiGe layer. • Optimizing Ga, Ge concentrations makes it possible to achieve an efficiency of 24%. [ABSTRACT FROM AUTHOR]

The electrical properties of InAsP/Si quantum dot solar cell (QDSC) are numerically studied and analyzed in this paper. Many effects like number of quantum dot (QD) layers inserted and Arsenic content of InAs x P 1-x on photovoltaic properties such as current density-voltage J-V and the external quantum efficiency (EQE) are investigated. Our results have been shown that the optimal Arsenic content is 0.6. With 30 InAsP/Si QDs layers, relative enhancements of about 7% and 6.70% of short-circuit current and efficiency are achieved, respectively. Otherwise, the absorption range edge of low energy photons was extended from 1120 to 1200 nm. This reveals that introduction of QDs in the intrinsic region of p -i- n Silicon (Si) solar cell enhances significantly the device characteristics beyond what has been reported for conventional semiconductor-based solar cells. [ABSTRACT FROM AUTHOR]

In this study, we experimentally elaborated Copper- and Indium-doped Zinc Oxide (Cu: ZnO and In: ZnO) thin films at different temperatures (T 1 = 480 °C and T 2 = 520 °C), the doping ratio were varied between 0% and 8%. Using a low cost solution-based chemical deposition, we have developed a ZnO thin film deposition process that offers fine-control of the surface morphology. It consists in spraying a volatile compound of the material to be deposited on a substrate maintained at high temperature to cause a chemical reaction in order to form at least one solid product. Therefore, the proposed ZnO doped layer is highly promising for applications for the next-generation solar cells. [ABSTRACT FROM AUTHOR]