Search

Traditional coiled tubing radial drilling with the same diameter cannot support deep and ultra-deep wells for high-pressure hydraulic jet drilling due to small diameter and sizeable hydraulic loss over long distances. The novel downhole movable pipe radial hydraulic drilling technique extracts a small diameter high-pressure injection pipe from the (tubing pipe) oil pipe and then drills it horizontally into the formation to form a radial hole. Dynamic sealing is the core of this technology, which achieves high-pressure fluid sealing while ensuring the injection pipe smoothly slides out of the oil pipe. A sealing tool is designed between the tubing and the injection pipe to prevent the leakage of high-pressure fluid. In this paper, the finite element model of the sealing tool was established, and the deformation and stress of the sealing tool under different interference and fluid pressure were simulated and analyzed. The relationship between stress distribution and contact pressure under the corresponding conditions was obtained. The results show that the von Mises stress increases significantly with the increase in fluid pressure under certain interference conditions. When the fluid pressure was 35 MPa, 52 MPa, and 70 MPa, the maximum von Mises stress was 29.65 MPa, 30.87 MPa, and 32.47 MPa, respectively, within a reasonable range. The stress peak area changes simultaneously, indicating that the possible damage location changes with the fluid pressure change. The maximum contact pressure between the sealing ring and the smooth rod increases with interference and fluid pressure, which always meets the sealing conditions. A laboratory test bench was built to test the high-pressure sealing performance of the sealing tool. Combined with the simulation data and test results, the downhole continuous rod dynamic sealing tool was modified to provide theoretical guidance for practical application. [ABSTRACT FROM AUTHOR]

Compressive stress in glass‐to‐metal seals is crucial to ensure sealing quality and service reliability. Photoluminescence spectroscopy (PS), which relies on the piezospectroscopic effect of Cr‐doped α‐Al2O3, shows promise for stress detection owing to its rapid detection, non‐destruction, and high resolution. The premise of the PS technique is to fill a glass matrix with alumina particles and detect signals from the alumina. In this study, the interaction between alumina particles and the glass matrix was analyzed to calibrate the measured stresses and investigate the stress state in the glass. Test results for glass‐to‐metal seals are believed to consist of simultaneous internal residual stress and external applied stress. The internal residual stress is formed due to the coefficient of thermal expansion mismatch between glass and alumina and is assumed to transfer by radial compression. In the experiment, it was detected by the PS technique and verified by X‐ray diffraction using an unstressed sample without metal housing. The external applied stress is formed due to metal housing compaction and possibly transferred by the shear effect. The stress distribution within the pre‐stressed sample containing metal housing was also measured by the PS technique. Then, calibrations were conducted on the measured stresses based on the deduced stress transfer relationships. Finally, finite element models were established to simulate the internal residual stress and external applied stress respectively to prove the validity of the calibration method, and mutually anastomotic results were obtained within the target margin of error. [ABSTRACT FROM AUTHOR]

To meet the requirements of alumina ceramics in delicate electronics, there is an urgent need for a low-temperature bonding technology that can realize a good combination of alumina and metal. In this work, alumina ceramics and nickel metals were successfully connected at a low temperature (25–150 °C) by Al-Ni self-propagating nanofoil as a heat source. The interface microstructure and element distributions of the solder joints from cross-section and fracture surface were investigated. In addition, the solder joint formation process was simulated by finite element analysis and molecular dynamics. These results showed that their shear strengths could be continuously improved with the growing temperature, which were 17.4 MPa (room temperature, 25 °C), 19.5 MPa (50 °C), 22.9 MPa (100 °C) and 25.69 MPa (150 °C). The Al 2 O 3 /Al-Ni nanofoil/Ni solder joints were prone to crack at the corner and boundary at Al 2 O 3 /solder interfaces due to the stress concentration. Moreover, the increase in ambient temperature not only raises the melting time and transient temperature during the self-propagating reaction, but also improves the interdiffusion of Ni and Sn atoms at the Ni/Sn interfaces. [ABSTRACT FROM AUTHOR]

Hydro-pneumatic springs often work under high pressure and alternating load conditions, which can easily cause seal damage, leakage, and serious failure. Relevant studies have shown that the dynamic seal failure of hydro-pneumatic springs is the main cause of hydro-pneumatic spring failure, and the sealing performance of GS sealing rings directly determines the service life of hydro-pneumatic springs. The influence of different sealing structure parameters on the sealing performance of GS sealing of hydro-pneumatic springs has been studied, which can provide effective theoretical guidance for the design of sealing structures related to hydro-pneumatic springs. However, the existing research on hydro-pneumatic springs mainly focuses on the characteristics of damping and stiffness; there is a relative lack of research on sealing performance and sealing structure, and the performance change law of GS seals under different working conditions is unclear. In this paper, a GS seal ring is selected as the main seal of the hydro-pneumatic spring, the material parameters of the GS seal ring are obtained via the single-axis compression test, and the finite element simulation method is used to establish the sealing model under different compression ratios of 10–30% and different pressure impacts of 5–30 MPa. By doing so, the stress nephogram, sealing ring shape, and sealing contact pressure of the GS sealing ring under different simulation parameters are obtained. From the test results, the decrease in compression ratio after the wear of the sealing ring is the main reason for the seal leakage of the hydro-pneumatic spring. The maximum contact stress of the sealing ring occurs at the lip of the step ring, and the maximum sealing pressure of the sealing ring is determined by the contact pressure of sealing surfaces II and III. The sealing performance of the GS-type combination sealing ring is affected by the compression ratio of the sealing ring and the impact pressure; when the compression ratio of the sealing ring is 15%, the sealing ring can meet the sealing work needs below 25 MPa. The research results provide a theoretical basis for the design of GS sealing of hydro-pneumatic springs and the effective improvement of the life and reliability of related equipment. [ABSTRACT FROM AUTHOR]

Top seal failure of ram blowout preventer (BOP) is one of the main factors leading to well control risk. The constitutive model and parameters of nitrile butadiene rubber (NBR) were optimized by compression and tensile tests, and the failure analysis model of the contact seal of the ram BOP top seal was built. The nonlinear contact mechanical behavior of the connection part of the BOP top seal was analyzed by the finite element method. Then, the influence of corrosion and wear defects at the top seal position of the 2FZ35-70 BOP under rated working pressure on the contact seal were studied, and the results showed that the overall contact pressure distribution of the top seal corrosion defects was uniform, the local contact pressure of the corrosion pit edge increased, and the top contact pressure decreased. The overall contact pressure of the wear defect of the top seal decreased linearly, the contact pressure at the maximum depth of the wear defect was the smallest, and the contact pressure gradually decreased to both sides. Ultimately, to guarantee the safety and reliability of the ram BOP, it is suggested that the acceptable depths of the seal corrosion pit and the wear at the top of the ram BOP are 4.0 mm and 0.2 mm, respectively, thus the reliability evaluation problem of the quantitative seal of the ram BOP top seal is solved. [ABSTRACT FROM AUTHOR]

Aiming to accurately predict the leakage rate of the sealing interface, this work proposes a two-dimensional finite element model of a proton exchange membrane fuel cell, which includes the microscopic surface morphology and the asperity contact process of the components. First of all, we constructed the surface morphology of the seal by the two-dimensional W-M (Weierstrass–Mandelbrot) fractal function and explored the influence of fractal dimension (D) and scale parameter (G) on the surface profile. Furthermore, the finite element method and Poiseuille fluid theory were adopted to obtain the deformation variables of the asperity under different clamping pressures and leakage rates. Moreover, we quantitatively analyzed the impact of surface roughness on the clamping pressure and leakage rate. It was found that both the surface amplitude and surface roughness are positively correlated with G and negatively correlated with D. Surface morphology is proportional to D but has no relationship with G. Additionally, the deformation asperity decreases exponentially with growing clamping pressure, and the leakage rate is consistent with the experimental values at a clamping pressure of 0.54 MPa. With the same leakage rate, when the seal surface roughness value is less than 1 μm, a doubled roughness value leads to an increase of 31% in the clamping pressure. In contrast, when the surface roughness of the seal is greater than 1 μm, a doubled roughness value induces an increase of 50% in the corresponding clamping pressure. [ABSTRACT FROM AUTHOR]

This paper presents a new type of three-axis gyroscope. The gyroscope comprises two independent parts, which are nested to further reduce the structure volume. The capacitive drive was adopted. The motion equation, capacitance design, and spring design of a three-axis gyroscope were introduced, and the corresponding formulas were derived. Furthermore, the X/Y driving frequency of the gyroscope was 5954.8 Hz, the Y-axis detection frequency was 5774.5 Hz, and the X-axis detection frequency was 6030.5 Hz, as determined by the finite element simulation method. The Z-axis driving frequency was 10,728 Hz, and the Z-axis sensing frequency was 10,725 Hz. The MEMS gyroscope's Z-axis driving mode and the sensing mode's frequency were slightly mismatched, so the gyroscope demonstrated a larger bandwidth and higher Z-axis mechanical sensitivity. In addition, the structure also has good Z-axis impact resistance. The transient impact simulation of the gyroscope structure showed that the maximum stress of the sensitive structure under the impact of 10,000 g@5 ms was 300.18 Mpa. The gyroscope was produced by etching silicon wafers in DRIE mode to obtain a high aspect ratio structure, tightly connected to the glass substrate by silicon/glass anode bonding technology. [ABSTRACT FROM AUTHOR]

Summary. Air conditioning systems in vehicles require long-term reliability during their entire service life. Especially, a good sealing function is needed for the prevention of coolant leaking. Unfortunately, in specific cases, after a particular time, screw connections of the air conditioning circuit lose their tightness, and the coolant starts to leak. Therefore, this paper focuses on the analysis and design optimisation of screw connections. We used the finite element method for describing the sealing, screw and disc spring behaviour. Then, we proposed a new design of the disc spring to obtain the proper force-deformation characteristics of the connection and ensure the tightness of the screw connection. [ABSTRACT FROM AUTHOR]

In the process of copper alloy hot continuous rolling, the problem of copper sticking to the roller seriously affects the surface quality, performance, and service life of the copper products. Roll sticking occurs as the adhesion energy of Cu is lower than that of Fe and the Fe-Cu interface, and the severe surface deformation which forces the copper into direct contact with the roll during the process of profile rolling. Based on the copper deformation law and adhesion phenomenon in the hot continuous rolling process, a rolling deformation model and roll copper adhesion model or copper alloy hot continuous rolling were established, and their simulation was realized using finite element software. Through finite element modeling of the hot rolling deformation zone, the distribution of the temperature, contact normal stress, and exposure rate in the hot rolling deformation zone were obtained, which were consistent with the actual roll adhesion phenomenon and copper adhesion position. To address the copper sticking behavior of the rolls, the process optimization method of matching the motor speed with the elongation coefficient (the 1# and 2# motor speeds were adjusted to 1549 r/min and 1586 r/min, respectively), adjusting the roll gap to 7.9 mm, and increasing the number and pressure of roll spray nozzles were put forward, which effectively solved the problem of copper sticking to the roll, significantly improved the surface quality of the copper and the service life of the roll, and can be used in production. [ABSTRACT FROM AUTHOR]

Solid-state dissimilar bi- or multi-metallic bonding is promising for achieving lightweight or multifunctional components in automotive, nuclear power and aerospace industries. To understand how to achieve a high-quality bonding interface between dissimilar materials, aluminium alloy (Al)–steel (Fe) bimetal gears manufactured under hot forge bonding were systematically investigated. In this work, comprehensive analyses of forge bonding mechanics, microstructure features, bonding interface behaviours and resulting mechanical properties were undertaken using ex/in-situ experiments and finite element modelling. The results revealed that the bonding behaviour and microstructure evolution were significantly affected by the mechanical property mismatch between the two dissimilar workpieces (AA6082 and E355). This mismatch could be effectively adjusted by setting different forging temperatures. The interfacial bonding strengths of AA6082 and E355, manufactured at low and high temperatures, were observed to be governed by interdiffusion and oxide particles, respectively. Balancing interdiffusion and oxide breaking appears to be key to achieving optimized interface strength for dissimilar bimetallic forge bonding technology. [Display omitted] • Bimetallic gears were proved that can be effectively manufactured through solid-state hot forge-bonding. • Correlations between processes interface properties were established. • The interface behaviours were affected by the mechanical property mismatch. • Balancing interdiffusion and oxide breaking appears key to achieving optimized interface strength. [ABSTRACT FROM AUTHOR]

• Compressive responses of canted coil spring and spring ring are well predicted. • Wear of spring-energized PTFE seals under ultra-high cycle operations is assessed. • Simulated worn seal cross section is in fair agreement with the measured one. • Sealing capability is evaluated via Reynolds equation and successfully validated. Spring-energized polytetrafluoroethylene (PTFE) seals are typically utilized to meet requirements of long service life due to their excellent temperature and chemical resistance. After high-cycle operations, the contact pressure between the seal lip and the associated counterpart possibly decrease because of the wear on the contact surface and this eventually leads to loss of the sealing capability. Evaluations of the wear and resulting sealing performance of the seal are rather essential, however, the corresponding experiments are generally time consuming and costly. Simulation procedures for the seal based on the finite element analysis were therefore developed in the current study. Experimental and numerical investigations of mechanical behaviors of the canted coil spring and PTFE materials were first performed. A wear analysis model for the spring-energized PTFE seal used in a glue dispenser with reciprocating motions for semiconductor equipment was subsequently constructed. The modified Archard model was implemented into a self-coded user subroutine of commercial finite element software to assess the amount of wear on the seal. Simulation results revealed that the geometry dimensions of the worn seal are in fair agreement with those of the corresponding samples. Contact pressure distributions of the seal lip were also examined during the operations. Peak of the contact pressure was found to gradually decrease along with the increase of cycles due to the wear, and potential fluid leakage was then assessed via the Reynolds equation. Numerical calculations showed that no leakage would occur after ultra-high cycle operations which was consistent with practical observations. [ABSTRACT FROM AUTHOR]