Search

A polymer fiber-based adsorbent (AF1) composed of acrylonitrile and itaconic acid functional groups was synthesized by a radiation-induced graft polymerization technique onto hollow-gear shaped pol...

The chromatographic resins DGA and LN have been used sequentially to separate curium, californium, plutonium, and various fission products (FPs) to obtain products with a pure radioisotope or a rad...

We investigate the effect of high-surface-area self-assembled TiO2:Cu2O nanostructures for CO2 and relative humidity gravimetric detection using polyethylenimine (PEI), 1-ethyl-3-methylimidazolium (EMIM), and polyacrylamide (PAAm). Introduction of hierarchical TiO2:Cu2O nanostructures on the surface of quartz crystal microbalance sensors is found to significantly improve sensitivity to CO2 and to H2O vapor. The response of EMIM to CO2 increases fivefold for 100 nm-thick TiO2:Cu2O as compared to gold. At ambient CO2 concentrations, the hierarchical assembly operates as a sensor with excellent reversibility, while at higher pressures, the CO2 desorption rate decreases, suggesting possible application for CO2 sequestration under these conditions. The gravimetric response of PEI to CO2 increases by a factor of 3 upon introduction of a 50 nm TiO2:Cu2O layer. The PAAm gravimetric response to water vapor also increases by a factor of 3 and displays improved reversibility with the addition of 50 nm TiO2:Cu2O structures. We found that TiO2:Cu2O can be used to lower the detection limits for CO2 sensing with EMIM and PEI and lower the detection limits for H2O sensing with PAAm by over a factor of 2. Coarse-grained and all-atom molecular dynamics simulations indicate the dissociative character of ionic liquid assembly on TiO2:Cu2O interfaces and different distributions of CO2 and H2O molecules on bare and ionic liquid-coated surfaces, confirming experimental observations. Overall, our results show high potential of hierarchical assemblies of TiO2:Cu2O/room temperature ionic liquid and polymer films for sensors and CO2 sequestration.

Water electrolysis can hinder the operation of capacitive deionization (CDI) and membrane CDI (MCDI). This study is aimed at investigating the overpotential limits of CDI and MCDI (OP-MCDI) for wat...

Ethane, the second major component of shale gas, is a prospective raw feedstock to valuable chemicals and fuels. Innovative pillared ZSM-5 with various lamellar thicknesses and Si/Al ratios were su...

The salt removal capacity (SRC) of the carbon electrodes in membrane capacitive deionization (MCDI) is limited by the applied potential (

Neutralization of the bio-oil pH has been shown to generate a neutralized bio-oil aqueous phase (NBOAP) that includes most of the acidic components and a neutralized bio-oil organic phase (NBOOP) that includes hydrophobic organics, such as phenols. NBOOP can be used for fuel production, while NBOAP can be fed to microbial electrolysis cells (MECs) for hydrogen production. After pH neutralization, some organic acidic components remain in NBOOP. This work is focused on capturing acidic compounds from NBOOP through water extraction and electrosorption, and demonstrating hydrogen production via MECs. Capacitive deionization (CDI) is proven effective in capturing ions from NBOOP-contacted water and NBOAP via electrosorption. Captured acidic compounds enable the MEC application to effectively produce renewable hydrogen. Chemical oxygen demand (COD) removal of 49.2%, 61.5%, and 60.8% for 2, 4, and 10 g/L-anode/day loading were observed, corresponding to a total COD degradation of 0.19 g/L, 0.79 g/L, and 1.3 g/L, respectively. A maximum hydrogen productivity of 4.3 L-H2/L-anode/day was obtained. Major compounds in the water phase such as fatty acids, sugar derivatives, furanic and phenolic compounds were converted to hydrogen with an efficiency of 80–90%. This approach may lead the entire biomass pyrolysis process to be an overall carbon-neutral process.

Simple and easily integrated design of flexible and transparent electrode materials affixed to polymer-based substrates hold great promise to have a revolutionary impact on the functionality and performance of energy storage devices for many future consumer electronics. Among these applications are touch sensors, roll-up displays, photovoltaic cells, health monitors, wireless sensors, and wearable communication devices. Here, we report an environmentally friendly, simple, and versatile approach to produce optically transparent and mechanically flexible all-solid-state supercapacitor devices. These supercapacitors were constructed on tin-doped indium oxide coated polyethylene terephthalate substrates by intercalation of a polymer-based gel electrolyte between two reduced graphene oxide (rGO) thin-film electrodes. The rGO electrodes were fabricated simply by drop-casting of graphene oxide (GO) films, followed by a novel low-temperature (≤250 °C) vacuum-assisted annealing approach for the in situ reduction of GO to rGO. A trade-off between the optical transparency and electrochemical performance is determined by the concentration of the GO in the initial dispersion, whereby the highest capacitance (∼650 μF cm

The ability to reuse amidoxime-based polymeric adsorbents is a critical component in reducing the overall cost of the technology to extract uranium from seawater. This report describes an evaluation of adsorbent reusability in multiple reuse (adsorption/stripping) cycles in real seawater exposures with potassium bicarbonate (KHCO3) elution using several amidoxime-based polymeric adsorbents. The KHCO3 elution technique achieved ∼100% recovery of uranium adsorption capacity in the first reuse. Subsequent reuses showed significant drops in adsorption capacity. After the fourth reuse with the ORNL AI8 adsorbent, the 56-day adsorption capacity dropped to 28% of its original capacity. FTIR spectra revealed that there was a conversion of the amidoxime ligands to carboxylate groups during extended seawater exposure, becoming more significant with longer exposure times. Ca and Mg adsorption capacities also increased with each reuse cycle supporting the hypothesis that long-term exposure resulted in converting amid...

Brush-on-brush structures are proposed as one method to overcome support effects in grafted polymers. Utilizing glycidyl methacrylate (GMA) grafted on polyethylene (PE) fibers using radiation-induced graft polymerization (RIGP) provides a hydrophilic surface on the hydrophobic PE. When integrated with atom transfer radical polymerization (ATRP), the grafting of acrylonitrile (AN) and hydroxyethyl acrylate (HEA) can be controlled and manipulated more easily than with RIGP. Poly(acrylonitrile)-co-poly(hydroxyethyl acrylate) chains were grown via ATRP on PE-GMA fibers to generate an adsorbent for the extraction of uranium from seawater. The prepared adsorbents in this study demonstrated promise (159.9 g-U/kg of adsorbent) in laboratory screening tests using a high uranium concentration brine and 1.24 g-U/kg of adsorbent in the filtered natural seawater in 21 days. The modest capacity in 21 days exceeds previous efforts to generate brush-on-brush adsorbents by ATRP while manipulating the apparent surface hydr...

Uranium adsorbed on amidoxime-based polyethylene fibers in simulated seawater can be quantitatively eluted using 3 M KHCO3 at 40 °C. Thermodynamic calculations are in agreement with the experimental observation that at high bicarbonate concentrations (3 M) uranyl ions bound to amidoxime molecules are converted to uranyl tris-carbonato complex in the aqueous solution. The elution process is basically the reverse reaction of the uranium adsorption process which occurs at a very low bicarbonate concentration (∼10−3 M) in seawater. In real seawater experiments, the bicarbonate elution is followed by a NaOH treatment to remove natural organic matter adsorbed on the polymer adsorbent. Using the sequential bicarbonate and NaOH elution, the adsorbent is reusable after rinsing with deionized water and the recycled adsorbent shows no loss of uranium loading capacity based on real seawater experiments.

The production of high-strength carbon fibers is an energy-intensive process, where a significant cost involves the wet or dry-spinning of polyacrylonitrile (PAN) fiber precursors. Melt-spinning PAN fibers would allow for significant reduction in the production cost and production hazards. Ionic liquids (ILs) are an attractive fiber-processing medium because of their negligible vapor pressure and low toxicity. In addition, they are carbon-forming precursors; upon carbonization, residual ILs can enhance the carbon yield, although primarily useful for plasticized melt-spinning of PAN precursor fibers. In this research, we investigated the influence of the molecular structure of ILs and the control of plasticizing interactions with PAN during melt-spinning. The structural, thermal, and mechanical properties of the melt-spun PAN fibers were obtained by a combination of various characterization methods, such as differential scanning calorimetry, thermogravimetric analysis, Fourier transform infrared spectroscopy, scanning electron microscopy, X-ray diffraction, and mechanical testing. These results demonstrated that the IL structure and counteranions influence the PAN fiber formation. More specifically, ILs containing bromide counteranions produced PAN precursor fibers with increased mechanical properties compared to ILs containing chloride anions. Our research can provide a foundation to understand the influence of ILs on melt-spinning of PAN fibers and provides us the guidelines for a higher cost-/energy-efficient production of PAN-based carbon fibers.

The local structure of dilute CrCl3 in a molten MgCl2:KCl salt was investigated by in situ x-ray absorption spectroscopy (XAS) at temperatures from room temperature to 800oC. This constitutes the first experiment where dilute Cr speciation is explored in a molten chloride salt, ostensibly due to the compounding challenges arising from a low Cr concentration in a matrix of heavy absorbers at extreme temperatures. CrCl3 was confirmed to be the stable species between 200 and 500oC, while mobility of metal ions at higher temperature (>700oC) prevented confirmation of the local structure.

Molten salts for use as heat transfer fluids in concentrated solar or nuclear power plants have experienced a resurgence over the past decade with a special focus on chloride-based salt mixtures, particularly for use in concentrating solar power and fast-spectrum nuclear reactors. Salt purification, specifically oxide removal, is required even for high purity commercial salts and can be achieved using many different methods. Carbochlorination, however, proves most effective according to thermodynamics and produces a gaseous byproduct easily removed from the salt. A variety of carbochlorinating reagents and reagent combinations were evaluated for thermodynamic favorability in the removal of common impurities in MgCl2-based feedstock or coverage gases used in industrial systems. Carbon tetrachloride exhibited superior purification thermodynamics above the melting point of common MgCl2-based salt compositions. Salt with composition of 68 : 32 mol% KCl : MgCl2 was purified on the kilogram scale by sparging with carbon tetrachloride, reducing dissolved oxide to trace levels (42 μmol MgO/kg salt). Interestingly, the lower purity salts exhibited magnesium and oxygen presence along grain boundaries in the corrosion layers while the purified salts did not, highlighting the need for decreased oxide content. The lessened corrosivity of the highly purified salt suggests a proper salt treatment may reduce dependence on specialized materials for use with molten salts.

Over millennia, nature has evolved an ability to selectively recognize and sequester specific metal ions by employing a wide variety of supramolecular chelators. Iron-specific molecular carriers—siderophores—are noteworthy for their structural elegance, while exhibiting some of the strongest and most selective binding towards a specific metal ion. Development of simple uranyl (UO22+) recognition motifs possessing siderophore-like selectivity, however, presents a challenge. Herein we report a comprehensive theoretical, crystallographic and spectroscopic studies on the UO22+ binding with a non-toxic siderophore-inspired chelator, 2,6-bis[hydroxy(methyl)amino]-4-morpholino-1,3,5-triazine (H2BHT). The optimal pKa values and structural preorganization endow H2BHT with one of the highest uranyl binding affinity and selectivity among molecular chelators. The results of small-molecule standards are validated by a proof-of-principle development of the H2BHT-functionalized polymeric adsorbent material that affords high uranium uptake capacity even in the presence of competing vanadium (V) ions in aqueous medium., Development of simple uranyl recognition motifs possessing siderophore-like binding strength and selectivity presents a challenge. Here the authors show a comprehensive theoretical and experimental study on uranyl binding with a polymeric adsorbent material decorated with a non-toxic siderophore inspired small molecule chelator.

A new series of amidoxime-based polymer adsorbents were synthesized at the Oak Ridge National Laboratory (ORNL) by electron beam induced grafting of acrylonitrile and itaconic acid onto polyethylene fiber. Hydroxylamine derivatives of poly(acrylonitrile) (PAN) moiety are demonstrated to possess two kinds of functional groups: open-chain amidoxime and cyclic imide dioxime. The open-chain amidoxime is shown to convert to imide dioxime on heat treatment in the presence of an aprotic solvent, like dimethylsulfoxide (DMSO). The formation of amidoxime and imide dioxime was confirmed by 13C CP-MAS spectra. The adsorbents were evaluated for uranium adsorption efficiency at ORNL with simulated seawater spiked with 8 ppm uranium and 5 gallon seawater in a batch reactor, and in flow-through columns with natural seawater at the Marine Science Laboratory (MSL) of Pacific Northwest National Laboratory (PNNL) at Sequim Bay, WA. The DMSO-heat-treated sorbents adsorbed uranium as high as 4.48 g-U/kg-ads. from seawater. Experimental evidence is presented that the poly(imide dioxime) is primarily responsible for enhanced uranium adsorption capacity from natural seawater. The conjugated system in the imide dioxime ligand possesses increased electron donation ability, which is believed to significantly enhance the uranyl coordination in seawater.

Sodium amide (NaNH2), a readily available strong base, was investigated as an efficient reagent for chemical activation of mesoporous carbon (MC) in the temperature range of 400–900 °C, aiming to enhance the CO2 adsorption performance. Total surface area and pore volume of the activated MC increase greatly with the activation temperature up to 700 °C and then tend to level off. Small micropores with a diameter

The extraction of uranium from seawater has received significant interest recently, because of the possibility of a near-limitless supply of uranium to fuel the nuclear power industry. While sorbent development has focused primarily on polymeric sorbents, nanomaterials represent a new area that has the potential to surpass the current polymeric sorbents, because of the high surface areas that are possible. Mesoporous carbon materials are a stable, high-surface-area material capable of extracting various chemical species from a variety of environments. Herein, we report the use of a dual templating process to understand the effect of pore size on the adsorption of uranyl ions from a uranyl brine consisting of seawater-relevant sodium, chloride, and bicarbonate ions. It was found that pore size played a more significant role in the effective use of the grafted polymer, leading to higher uranium capacities than the surface area. Therefore, the pore size must be tailored to meet the demands of the extraction ...

The need to secure future supplies of energy attracts researchers in several countries to a vast resource of nuclear energy fuel: uranium in seawater (estimated at 4.5 billion tons in seawater). In this study, we developed effective adsorbent fibers for the recovery of uranium from seawater via atom-transfer radical polymerization (ATRP) from a poly(vinyl chloride)-co-chlorinated poly(vinyl chloride) (PVC-co-CPVC) fiber. ATRP was employed in the surface graft polymerization of acrylonitrile (AN) and tert-butyl acrylate (tBA), precursors for uranium-interacting functional groups, from PVC-co-CPVC fiber. The [tBA]/[AN] was systematically varied to identify the optimal ratio between hydrophilic groups (from tBA) and uranyl-binding ligands (from AN). The best performing adsorbent fiber, the one with the optimal [tBA]/[AN] ratio and a high degree of grafting (1390%), demonstrated uranium adsorption capacities that are significantly greater than those of the Japan Atomic Energy Agency (JAEA) reference fiber in ...

The Pacific Northwest National Laboratory (PNNL) is evaluating the performance of adsorption materials to extract uranium from natural seawater. Testing consists of measurements of the adsorption of uranium and other elements from seawater as a function of time using flow-through columns and a recirculating flume to determine adsorbent capacity and adsorption kinetics. The amidoxime-based polymer adsorbent AF1, produced by Oak Ridge National Laboratory (ORNL), had a 56-day adsorption capacity of 3.9 ± 0.2 g U/kg adsorbent material, a saturation capacity of 5.4 ± 0.2 g U/kg adsorbent material, and a half-saturation time of 23 ± 2 days. The ORNL AF1 adsorbent has a very high affinity for uranium, as evidenced by a 56-day distribution coefficient between adsorbent and solution of log KD,56day = 6.08. Calcium and magnesium account for a majority of the cations adsorbed by the ORNL amidoxime-based adsorbents (61% by mass and 74% by molar percent), uranium is the fourth most abundant element adsorbed by mass an...

This work presents a soft templating approach for mesoporous carbon using the polyphenolic heterogeneous biomass, chestnut tannin, as the carbon precursor. By varying synthesis parameters such as tannin:surfactant ratio, cross-linker, reaction time and acid catalyst, the pore structure could be controllably modulated from lamellar to a more ordered hexagonal array. Carbonization at 600 °C under nitrogen produced a bimodal micro-mesoporous carbonaceous material exhibiting enhanced hydrogen bonding with the soft template, similar to that shown by soft-templating of phenolic-formaldehyde resins, allowing for a tailorable pore size. By utilizing the acidic nature of chestnut tannin (i.e. gallic and ellagic acid), hexagonal-type mesostructures were formed without the use of an acid catalyst. The porous carbon materials were activated with ammonia to increase the available surface area and incorporate nitrogen-containing functionality which led to a maximum CO2 adsorption capacity at 1 bar of 3.44 mmol/g and 2.27 mmol/g at 0 °C and 25 °C, respectively. The ammonia-activated carbon exhibited multiple peaks in the adsorption energy distribution which indicates heterogeneity of adsorption sites for CO2 capture.

A high-sensitivity 4H–SiC temperature sensor and an alpha detector have been fabricated using additively printed metal contacts. The surface morphology and electrical conductivity of the printed electrodes were established prior to Schottky diode development. 4H–SiC Schottky diodes with direct-write printed silver contacts on the 5 μm-thick epilayer on 4H–SiC were characterized electrically in terms of the forward and reverse current–voltage and high-frequency capacitance–voltage characteristics. The turn-on voltage of the Schottky diodes, as established from the forward current–voltage characteristics measured up to a temperature of 400 °C, showed a linear temperature dependence. Schottky diodes with direct-write printed Ag electrodes were able to measure alpha particles emitted from Americium-241. The high temperature and radiation response of the Schottky diodes show their suitability for multi-modal sensor fusion on the 4H–SiC platform for harsh environment applications.

The development of technology to harvest the uranium dissolved in seawater would enable access to vast quantities of this critical metal for nuclear power generation. Amidoxime polymers are the most promising platforms for achieving this separation, yet the design of advanced adsorbents is hindered by uncertainty regarding the uranium binding mode. In this work we use XAFS to investigate the uranium coordination environment in an amidoxime-phosphonic acid copolymer adsorbent. In contrast to the binding mode predicted computationally and from small molecule studies, a cooperative chelating model is favoured, attributable to emergent behavior resulting from inclusion of amidoxime in the polymer. Samples exposed to seawater also display a feature consistent with a μ(2)-oxo-bridged transition metal, suggesting the formation of an in situ specific binding site. These findings challenge long held assumptions and provide new opportunities for the design of advanced adsorbent materials.

Limited resource availability and population growth have motivated interest in harvesting valuable metals from unconventional reserves, but developing selective adsorbents for this task requires structural knowledge of metal binding environments. Amidoxime polymers have been identified as the most promising platform for large-scale extraction of uranium from seawater. However, despite more than 30 years of research, the uranyl coordination environment on these adsorbents has not been positively identified. We report the first XAFS investigation of polyamidoxime-bound uranyl, with EXAFS fits suggesting a cooperative chelating model, rather than the tridentate or η2 motifs proposed by small molecule and computational studies. Samples exposed to environmental seawater also display a feature consistent with a μ2-oxo-bridged transition metal in the uranyl coordination sphere, suggesting in situ formation of a specific binding site or mineralization of uranium on the polymer surface. These unexpected findings challenge several long-held assumptions and have significant implications for development of polymer adsorbents with high selectivity.

A novel ligand-functionalized adsorbent material was prepared using a combination of radiation-induced graft polymerization (RIGP) and click chemistry (1,3 cycloaddition reaction). The design of the ligand-containing amidoxime functionality is based on its chelating efficiency with uranium. In this process, RIGP is used to graft polymer chains on fiber substrates, where the fibers are prepared by irradiating and treating polyethylene (PE) with different bulk ratios of vinyl benzyl chloride and acrylic acid or itaconic acid. Furthermore, chemical modifications of these fibers are performed using a two-step process, where novel bisimidoxime ligands are incorporated into fibers. These ligands contain imidedioxime, which is known to be a uranophile. Also, the core structure of the ligand containing three donor atoms facilitates the formation of chelate with uranyl ion in media such as seawater. Density functional theory calculations were performed to quantify the binding strength with the uranyl ion. When tes...

High-surface-area amidoxime and carboxylic acid grafted polymer adsorbents developed at Oak Ridge National Laboratory were tested for sequestering uranium in a flowing seawater flume system at the PNNL-Marine Sciences Laboratory. FTIR spectra indicate that a KOH conditioning process is necessary to remove the proton from the carboxylic acid and make the sorbent effective for sequestering uranium from seawater. The alkaline conditioning process also converts the amidoxime groups to carboxylate groups in the adsorbent. Both Na2CO3–H2O2 and hydrochloric acid elution methods can remove ∼95% of the uranium sequestered by the adsorbent after 42 days of exposure in real seawater. The Na2CO3–H2O2 elution method is more selective for uranium than conventional acid elution. Iron and vanadium are the two major transition metals competing with uranium for adsorption to the amidoxime-based adsorbents in real seawater. Tiron (4,5-dihydroxy-1,3-benzenedisulfonic acid disodium salt, 1 M) can remove iron from the adsorben...

Seawater contains uranium at an average concentration of 3.3 ppb, as well as a variety of other ions at either overwhelmingly higher or similar concentrations, which complicate the recovery of uranium. This report describes an investigation of the effects of various factors such as uranium speciation and presence of salts including sodium, calcium, magnesium, and bicarbonate, as well as trace elements such as vanadium on uranium adsorption kinetics in laboratory experiments. Adsorption models are also developed to describe the experimental data of uranium extraction from seawater. Results show that the presence of calcium and magnesium significantly slows down the uranium adsorption kinetics. Vanadium can replace uranium from amidoxime-based adsorbent in the presence of sodium in the solution. Results also show that bicarbonate in the solution strongly competes with amidoxime for binding uranium, and thus slows down the uranium adsorption kinetics. Developed on the basis of the experimental findings, the ...

Poly(acrylamidoxime) fibers are the current state of the art adsorbent for mining uranium from seawater. While the acid dissociation constants, pKa, of characteristic amidoxime and carboxylate ligands have been reported in the literature, the proton affinity distribution of the poly(acrylamidoxime) fiber is yet to be established. Herein, we report the poly(acrylamidoxime) proton affinity distribution between pH 2 and pH 10 via the stable numerical solution of the adsorption integral equation using splines (SAIUS) algorithm. Two peaks in the proton affinity distribution of poly(acrylamidoxime) were observed: the neutral to anionic dissociation of the carboxylate monomer between pH 3.2 and pH 4.4 (pKa ≈ 4.0) and the protonated to neutral dissociation of the acyclic amidoxime monomer between pH 5.6 and pH 6.8 (pKa ≈ 6.1). The acidity constants obtained for the carboxylate and amidoximate monomers vary from the acidity constants of acetic acid and acetamidoxime, respectively. These variations in acidity can b...

Extraction of uranium (U) from seawater for use as a nuclear fuel is a significant challenge due to the low concentration of U in seawater (∼3.3 ppb) and difficulties to selectively extract U from the background of major and trace elements in seawater. The Pacific Northwest National Laboratory (PNNL)’s Marine Sciences Laboratory (MSL) has been serving as a marine test site for determining performance characteristics (adsorption capacity, adsorption kinetics, and selectivity) of novel amidoxime-based polymeric adsorbents developed at Oak Ridge National Laboratory (ORNL) under natural seawater exposure conditions. This manuscript describes the performance of three formulations (38H, AF1, AI8) of amidoxime-based polymeric adsorbents produced at ORNL in MSL’s ambient seawater testing facility. The adsorbents were produced in two forms, fibrous material (40–100 mg samples) and braided material (5–10 g samples), and exposed to natural seawater using flow-through columns and recirculating flumes. All three formu...

A new family of high-surface-area polyethylene fiber adsorbents named the AF series was recently developed at the Oak Ridge National Laboratory (ORNL). The AF series adsorbents were synthesized by radiation-induced graft polymerization of acrylonitrile and itaconic acid (at different monomer/comonomer mol ratios) onto high surface area polyethylene fibers. The degree of grafting (%DOG) of AF series adsorbents was found to be 154–354%. The grafted nitrile groups were converted to amidoxime groups by treating with hydroxylamine. The amidoximated adsorbents were then conditioned with 0.44 M KOH at 80 °C followed by screening at ORNL with sodium-based synthetic aqueous solution, spiked with 8 ppm uranium. The uranium adsorption capacity in simulated seawater screening ranged from 170 to 200 g-U/kg-ads irrespective of %DOG. A monomer/comonomer molar ratio in the range of 7.57–10.14 seemed to be optimum for highest uranium loading capacity. Subsequently, the adsorbents were also tested with natural seawater at ...

In order to ensure a sustainable reserve of fuel for nuclear power generation, tremendous research efforts have been devoted to developing advanced sorbent materials for extracting uranium from seawater. In this work, a porous aromatic framework (PAF) was surface-functionalized with poly(acrylonitrile) through atom-transfer radical polymerization (ATRP). Batches of this adsorbent were conditioned with potassium hydroxide (KOH) at room temperature or 80 °C prior to contact with a uranium-spiked seawater simulant, with minimal differences in uptake observed as a function of conditioning temperature. A maximum capacity of 4.81 g-U/kg-ads was obtained following 42 days contact with uranium-spiked filtered environmental seawater, which demonstrates a comparable adsorption rate. A kinetic investigation revealed extremely rapid uranyl uptake, with more than 80% saturation reached within 14 days. Relying on the semiordered structure of the PAF adsorbent, density functional theory (DFT) calculations reveal coopera...

Alkaline conditioning of the amidoxime based adsorbents is a significant step in the preparation of the adsorbent for uranium uptake from seawater. The effects of various alkaline conditioning parameters such as the type of alkaline reagent, reaction temperature, and reaction time were investigated with respect to uranium adsorption capacity from simulated seawater (spiked with 8 ppm uranium) and natural seawater (from Sequim Bay, WA). An adsorbent (AF1) was prepared at the Oak Ridge National Laboratory by radiation-induced graft polymerization (RIGP) with acrylonitrile and itaconic acid onto high-surface-area polyethylene fibers. For the AF1 adsorbent, sodium hydroxide emerged as a better reagent for alkaline conditioning over potassium hydroxide, which has typically been used in previous studies, because of higher uranium uptake capacity and lower cost over the other candidate alkaline reagents investigated in this study. Use of sodium hydroxide in place of potassium hydroxide is shown to result in a 21...

A high-surface-area polyethylene-fiber adsorbent (AF160-2) has been developed at the Oak Ridge National Laboratory by radiation-induced graft polymerization of acrylonitrile and itaconic acid. The grafted nitriles were converted to amidoxime groups by treating with hydroxylamine. The amidoximated adsorbents were then conditioned with potassium hydroxide (KOH) by varying different reaction parameters such as KOH concentration (0.2, 0.44, and 0.6 M), duration (1, 2, and 3 h), and temperature (60, 70, and 80 °C). Adsorbent screening was then performed with simulated seawater solutions containing sodium chloride and sodium bicarbonate, at concentrations found in seawater, and uranium nitrate at a uranium concentration of ∼7–8 ppm and pH 8. Fourier transform infrared spectroscopy and solid-state NMR analyses indicated that a fraction of amidoxime groups was hydrolyzed to carboxylate during KOH conditioning. The uranium adsorption capacity in the simulated seawater screening solution gradually increased with co...

The hydrogenation of levulinic acid has been studied using Ru supported on ordered mesoporous carbons (OMCs) prepared by soft-templating. P- and S-containing acid groups were introduced by postsynthetic functionalization before the addition of 1 % Ru by incipient wetness impregnation. These functionalities and the reaction conditions mediate the activity and selectivity of the levulinic acid hydrogenation. The presence of S-containing groups (Ru/OMC-S and Ru/OMC-P/S) deactivates the Ru catalysts strongly, whereas the presence of P-containing groups (Ru/OMC-P) enhances the activity compared to that of pristine Ru/OMC. Under mild conditions (70 °C and 7 bar H2 ) the catalyst shows high selectivity to γ-valerolactone (GVL; >95 %) and high stability on recycling. However, under more severe conditions (200 °C and p H 2=40 bar) Ru/OMC-P is particularly able to promote GVL ring-opening and the consecutive hydrogenation to pentanoic acid.

In this work we have determined the room temperature electrochemical reactions of SnO2 thin films and mesoporous carbons filled with SnO2 anodes with Na, and compare the results with those obtained during the reaction with Li. We show that SnO2 can reversibly deliver up to 6.2 Li/SnO2 whereas the reaction with Na is significantly limited. The initial discharge capacity is equivalent to less than 4 Na/SnO2, which is expected to correspond to the formation of 2 Na2O and Sn. This limited discharge capacity suggests the negative role of the formed Na2O matrix upon the reversible reaction of Sn clusters. Moreover, the reversible cycling of less than 1 Na/SnO2, despite the utilization of 6–7 nm SnO2 particles, is indicative of sluggish reaction kinetics. The origin of this significant capacity reduction is probably due to the formation of a diffusion limiting interface. Furthermore, there is a larger apparent hysteresis compared to Li. These results point to the need to design composite structures of SnO2 nanoparticles with suitable morphological and conductivity components.

The viability of seawater-based uranium recovery depends on the uranium adsorption rate and capacity, since the concentration of uranium in the oceans is relatively low (3.3 μg L−1). An important consideration for a fast adsorption is to maximize the adsorption properties of adsorbents such as surface areas and pore structures, which can greatly improve the kinetics of uranium extraction and the adsorption capacity simultaneously. Following this consideration, macroporous monolith adsorbents were prepared from the copolymerization of acrylonitrile (AN) and N,N′-methylene-bis(acrylamide) (MBAAm) based on a cryogel method using both hydrophobic and hydrophilic monomers. The monolithic sorbents were tested with simulated seawater containing a high uranyl concentration (∼6 ppm) and the uranium adsorption results showed that the adsorption capacities are strongly influenced by the ratio of monomer to the crosslinker, i.e., the density of the amidoxime groups. The preliminary seawater testing indicates the high salinity content of seawater does not hinder the adsorption of uranium.

An innovative strategy for post-synthesis nitrogen-doping of mesoporous carbons (MCs) with high yields (>90%) at low temperatures (230–380 °C) by using a strong base, sodium amide (NaNH2), was developed. The as-prepared N-doped MCs exhibit a significantly enhanced CO2 adsorption performance in terms of capacity and selectivity when compared to their parent MCs.

More than 1000× uranium exists in the oceans than exists in terrestrial ores. With nuclear power generation expected to increase over the coming decades, access to this unconventional reserve is a matter of energy security. With origins in the mid-1950s, materials have been developed for the selective recovery of seawater uranium for more than six decades, with a renewed interest in particular since 2010. This review comprehensively surveys materials developed from 2000–2016 for recovery of seawater uranium, in particular including recent developments in inorganic materials; polymer adsorbents and related research pertaining to amidoxime; and nanostructured materials such as metal–organic frameworks, porous-organic polymers, and mesoporous carbons. Challenges of performing reliable and reproducible uranium adsorption studies are also discussed, as well as the standardization of parameters necessary to ensure valid comparisons between different adsorbents.

The incorporation of robust porous frameworks into polymer fibers with handleable morphologies and flexible chemical compositions exhibits significant advantages for device fabrication in a wide range of applications. However, the soft linear polymeric chains of the fibers make the generation of nanopores extremely challenging. Herein, a facile synthetic strategy based on a combination of functional monomer grafting and hyper-crosslinking technology is developed for the porous engineering of polymeric fibers. In this methodology, the nanoporous framework originating from the hyper-crosslinking of aromatic monomers is covalently grafted onto fibers, which is beneficial to retaining their unique fiber morphology and to preserving their excellent mechanical properties. Moreover, this promising protocol can be further extended to the porous functionalization of polymeric matrices with diverse morphologies for target-specific applications.