Search

The fabrication of most current thermal insulation materials from polymeric foams has created an unfavorable impact on the environment. With the aim of reducing the use of foam plastic, this paper focuses on honeycomb paperboard, an alternative thermal insulation material which is recyclable and cost-effective, and evaluates its heat transfer performance under different conditions. The experimental results show the effective thermal conductivity of honeycomb paperboard increases as the honeycomb height or the side length increases. This paper also establishes a novel theoretical model based on a newly developed convective heat transfer correlation to predict the effective thermal conductivity under different conditions. The model's results conform well to the experimental results, and the effect of convective heat transfer is investigated quantitatively using this model. As the vertical adiabatic boundary surfaces are replaced by honeycomb walls, the convection heat transfer strictly depends on the thermal boundary condition of the honeycomb walls and highly depends on honeycomb height and side length. • The novel theoretical models involving convective heat transfer are established under different conditions. • The different heat transfer paths are quantitatively investigated based on the proposed models. • Under the condition of hot-above and cold-below, convective heat transfer in honeycomb paperboard increases as the honeycomb height increases, but decreases as the side lengths increases. • Under the condition of cold-above and hot-below, convection heat transfer in honeycomb paperboard increases as the honeycomb height or the side length increases. [ABSTRACT FROM AUTHOR]

Highlights: [•] The addition of paper waste increases the thermal performance of bricks. [•] Paper waste additions into brick increase the porosity. [•] Predictive models for simulation and optimization of heat transfer process have been developed. [•] Material conductivity, surface emissivities and mean brick temperature have been considered as input variables. [•] The design of hollows in brick models helps further improve the thermal performance. [Copyright &y& Elsevier]

The Institute for Microelectronics and Microsystems of the Italian National Research Council (Italy) has designed and fabricated a water-fed MEMS vaporizing liquid microthruster (VLM) in collaboration with the University of Salento (Italy) and KU Leuven (Belgium). Previous studies have demonstrated the device's functioning and highlighted the presence of a strong thermoelectric-hydraulic coupling that severely affects the heating and propulsive efficiencies and reliability of the device. In this regard, the current work provides a preliminary experimental investigation of a pulsed heating system actively controlled by temperature using PI-D logic (proportional and integrative actions applied to the error; derivative action applied to the output). The overall performance assessment focuses on evaluating power consumption during steady-state operation and analyzing the dynamic response of the VLM undergoing such an actively controlled pulsed heating, which has been built using both manual and data-driven offline adaptive tuning of the PID parameters. Concerning the steady-state operation, results highlight a promising enhancement of the heating efficiency to values above 0.9. The dynamic response analysis shows that operating with a single set of fixed PID parameters is not feasible and that the manual tuning is a trial-and-error approach highly dependent on the operator's experience, operating conditions, and reference temperature profile. Furthermore, shorter rise and response times require a higher proportional gain, and the overshoot experienced when crossing the saturation temperature cannot be avoided. In this paper, we show that the response of the data-driven adaptive controller solves these issues, exhibiting a reduced maximum settling time from around 59 s to less than 10 s, while the overshoot is avoided thanks to the temporal adjustment of the PID parameters. • Thermoelectric-hydraulic coupling impacts VLM heating and propulsion efficiency. • PI-D controlled pulsed heating investigated for VLM propulsion. • Steady-state efficiency boosted beyond 0.9. • Adaptive controller reduces settling time. • Data-driven approach minimizes overshoot. [ABSTRACT FROM AUTHOR]

The aim of this paper is to propose an efficient numerical scheme to deal with heat transfer problems in pipe flow with a large length/diameter ratio. The generalized finite difference method (GFDM) is combined with a space stepping algorithm (SSA) for the solution. The SSA divides the solution domain into a number of overlapping sections in the length direction of the pipe. Due to the large Peclet number, the heat transport process is dominated by advection, which allows an approximate boundary condition to be applied at the downstream cross section. The problem is then solved section by section. Using the uniform distributed points, the solution matrix for each section does not change, and only the right hand side needs to be refreshed for the changing boundary conditions. This leads to a highly efficient scheme for problems with a large pipe length. To show the accuracy of the numerical scheme, a problem with available analytical solution is studied. Then the method is applied to problems of single pipe with different pipe wall temperature and flow Reynolds number, and concentric annular pipe. Numerical results confirm the stability and efficiency of the GFDM-SSA. The method can be applied to many real world transient heat transfer problems in which the pipe is heated or cooled along its length with arbitrary wall temperature for heat exchange and other purposes. [ABSTRACT FROM AUTHOR]

• A fully coupled three-dimensional THMC model (DEHydrate) is developed for simulating hydrate dissociation. • The numerical results obtained from the proposed model are in good agreement with those from other simulations. • Only a small fraction of gas produced from radial hydrate dissociation is collected from the wellbore. • The model provides an effective tool to predict the mechanical behavior during hydrate dissociation. Due to high energy density and huge reserves, many trial projects worldwide have been conducted to exploit natural gas hydrates (NGH). However, most of them did not meet the commercialization requirements because of submarine hazards, low gas production and sand production. Therefore, it is important to investigate the NGH dissociation process. In this paper, a fully coupled multiphase, strongly nonlinear three-dimensional (3D) thermal–hydro–mechanical–chemical model (DEHydrate) is developed to consider the multiphysics behaviours including solid-liquid-gas multiphase flow, heat transfer, NGH phase transition and solid deformation during hydrate dissociation. The model is solved using a fully implicit finite element method. The gas-liquid flow and heat transfer are simulated by low-order elements while the solid deformation is calculated by high- or low-order elements. The behaviours of the multiphase seepage and geomechanics are fully coupled and the physical properties of the reservoir are updated iteratively based on changes in pressure, temperature and displacement. The DEHydrate simulator provides an effective tool to predict the evolution of reservoir mechanical behavior during hydrate dissociation, including transient pressure, temperature, displacement and stress in the reservoir, as well as multiphase saturation, hydrate dissociation rate/mass and gas production rate/mass. During the NGH dissociation, the initial stage exhibits a rapid dissociation rate of up to 206.23 kg/(d·m) for NGH layer with a length of 600 m and a thickness of 22 m, which subsequently decreases to 11.64 kg/(d·m). Only a small portion of the gas generated during NGH dissociation is collected at the wellbore (approximately 35.6 % after 100 days), while the majority remains trapped in the reservoir. In addition, throughout NGH dissociation, the reservoir matrix continues to move toward the wellbore in the horizontal direction. While in the vertical direction, the reservoir matrix below the wellbore moves upwards, with decreasing displacement due to low-pressure diffusion, while the reservoir matrix above the wellbore moves downwards, with increasing displacement. The largest displacements occur near the wellbore during the early stage of NGH dissociation, while in the late stage, the largest displacements occur above the reservoir. [ABSTRACT FROM AUTHOR]

In this study, a computer model based on discrete element method is employed to simulate the unsteady state heat transfer from the fuser roll to the toner and coating layer during the Xerography printing of coated papers. The model coating layers consisted of randomly arranged spherical pigment and latex particles with commercially relevant size distributions. Effects of coating characteristics, toner size, multiple toner layers, toner melting energy, toner thermal conductivity, coating layer thermal conductivity, and fuser roll temperature and pressure were investigated. Iso-thermal contours of fusing time were generated to demonstrate the relative importance of different fusing conditions and toner properties. Simulation results showed that temperature variation highly depended on the toner size, toner melting energy and the fuser roll temperature. Moreover, simultaneous coupling of the compressive stress and heat transfer indicated that the pressure exerted by the fuser roll did not significantly affect the rate of heat transfer. [Copyright &y& Elsevier]

In our previous work, the coaxial electrostatic spinning method was applied to construct nanofiber/SiBCN ceramic aerogel with an elytra-mimetic structure. The material presented excellent mechanical, insulation, oxidation resistance, and other properties. Based on preliminary experiments and literature reports, the integrated heat transfer behavior of nanofiber/SiBCN composite ceramic aerogels in high-temperature environments was affected by several factors, such as coaxial fiber size properties, fiber particle content, interactions, and spatial distribution. Moreover, the above factors overlapped and interacted with each other, and it was hard to generalize a clear law of action through traditional experiments and characterization. Therefore, the paper constructed a representative volume unit (RVE) model based on the complex spatial distribution characteristics of composite aerogels, using fractal theory, Rosseland equation theory, and multiphase model theory. This paper investigated the fiber and particle content, the size characteristics of the coaxial fibers, and the overall heat transfer process in high-temperature environments using the finite element method. The finite element simulated the effective thermal conductivity of multiphase aerogel composites under multiple parameters, such as fiber occupancy, fiber core-shell diameter ratio, temperature, and heat transfer mode. We obtained the property parameters of the complex composition of the material through fractal theory. The model was combined with finite elements to study the fiber particle content, the size characteristics of coaxial fibers, and the integrated heat transfer process in high-temperature environments. The fibers improved the absorption and reflection of thermal radiation with increasing fiber mass fraction, leading to improved ability of ceramic fiber aerogel to extinguish light. The fibers had a larger area to absorb and reflect thermal radiation. Based on the excellent extinction ability of SiC fibers, the composite ceramic aerogel had improved thermal performance at a specifically fiber-to-shell diameter ratio through a comprehensive multifactor simulation analysis. [ABSTRACT FROM AUTHOR]

Abstract: One of the most important factors in the thermal behavior of exterior walls is the thermal conductivity of the clay in their bricks. The higher the percentage of lightening additives incorporated, the better the thermal behavior of the bricks. But as their thermal characteristics are improved the mechanical properties of bricks deteriorate. The goal is to study the influence of paper pulp as a lightening additive on the thermal and mechanical properties of the fired clay, and to improve the thermal properties as far as possible without the mechanical properties falling below the required levels. This involved the preparation of test specimens that were then subjected to the corresponding assays of thermal conductivity and mechanical strength. It is found that around 15% of paper pulp can be added without the brick''s mechanical properties ceasing to comply with current legislation. This amount of paper pulp has improved conductivity properties by 39.69% compared to the clay without additives, recording a minimum conductivity value at 10°C of 0.45W/m-K. This decrease in the conductivity of the clay results in a 16% improvement in equivalent thermal transmittance for brick walls made in the same way. [Copyright &y& Elsevier]

Abstract: In this work we present a mathematical model describing the coupled heat and moisture transport in paper. The model is solved numerically and the numerical solution is used to study the interdependency of the moisture and temperature distribution in paper. The results show that variation with temperature of the saturated water vapor concentration and the sorption isotherm parameters are both important for inducing moisture desorption. It is also found that for steep relative humidity ramps moisture sorption generates temperature increments that slow down the sorption process itself. The model is also used to study the moisture gradients in a paper sheet inside a printer from Océ Technologies, which contains a warm print surface. The results predict changes in moisture content of only 0.2%, which suggests that no deformations are induced on the printed sheet. [Copyright &y& Elsevier]

Abstract: Heat management is crucial to polymer electrolyte membrane (PEM) fuel cell commercialization. Numerical modeling is often used to simulate heat transfer in the various components of the cell and specifically the gas diffusion layer (GDL). Due to the porous nature of the gas diffusion layer and its complexity of anisotropy, the effect of the structure on the thermal conductivity is usually taken into account by introducing an effective thermal conductivity. In this study, the effective thermal conductivity of carbon paper diffusion media was estimated numerically. Carbon paper is often used as the GDL in PEM fuel cells due to its ability to efficiently transport electrons, heat and gaseous species. Using the GeoDict code, a realistic three-dimensional pore morphology of carbon paper was used as the modeling domain and the governing mathematical equations were solved using the commercial software package Fluent (6.3.26) and the ThermoDict solver. The geometrical effects on the effective thermal conductivity were investigated for different geometries. It was found that the effective thermal conductivity is highly sensitive to the geometry of the porous material under investigation. The effective thermal conductivity is much larger in the in-plane direction when compared with the value in the through-plane direction. Further, the change of the effective thermal conductivity due to porosity and compression was studied. Finally, correlations for the through-plane and in-plane effective thermal conductivity were developed. [Copyright &y& Elsevier]

Abstract: Copper-zinc oxide catalyst powders were successfully impregnated into paper-based composites (catalyst paper) of ceramic and silicon carbide (SiC) fibers, prepared using an established wet papermaking process. The catalyst powders were homogeneously scattered over the fiber-mix networks tailored within the catalyst paper. Samples of catalyst paper were subjected to the methanol steam reforming (MSR) process below 300°C to produce hydrogen gas for fuel cell applications. During this process, the catalyst paper samples exhibited a higher methanol conversion efficiency and lower carbon monoxide concentration than those produced either by a commercial pellet-type Cu/ZnO catalyst or the original powdered Cu/ZnO catalyst. The high heat conductivity of the SiC fibers enhanced the catalytic performance, especially contributing to the suppression of the reverse water gas shift reaction. The heat transfer and the heat distribution inside the catalyst paper were improved by the SiC fibers. The MSR efficiency per catalyst weight was greatly influenced by the addition of pulp fibers, which made the catalyst paper porous. Results indicated that these in-paper void structures are suitable for the MSR reaction. Flexible catalyst paper is a promising, easy-to-handle material for practical MSR applications, due to the controllable heat and pore characteristics involved in the MSR performance. [Copyright &y& Elsevier]

In the high-temperature environment, a larger thermal expansion mismatch of a bimaterial leads to pronounced thermal stresses and interface crack growth. In this paper, a generalized fractional heat conduction model is used to determine the instantaneous thermal fracture behaviors of a bimaterial interface crack. An axisymmetric thermoelastic problem is solved with the aid of Goodier's thermoelastic displacement potential and Love's potential functions. A mixed initial-boundary value problem is then converted to a singular integral equation of second kind by using the Hankel and Laplace integral transforms. Numerical results of the intensity factors of heat flux and thermal stresses are evaluated using Stehfest's Laplace inversion scheme. The influence of fractional kernel functions with power and exponential law are analyzed, respectively, for aluminum-steel and steel-epoxy, respectively. The thermal stress intensity factors exhibit more wave-like behaviors based on Riemann-Liouville and Atangana-Baleanu models which is different from Caputo-Fabrizio and the complete diffusion model. • An interface crack between dissimilar materials is analyzed. • Goodier's and Love's potential functions are utilized for solving the problem. • Transient heat flux and thermal stress intensity factors are investigated. • Characteristics for various fractional heat flux kernel are considered. [ABSTRACT FROM AUTHOR]

In the integrated circuit industry, heat is transferred through the contact between wafers and the chemical vapor deposited (CVD) 3C–SiC wafer susceptor. Understanding the out-plane thermal conductivity of CVD 3C–SiC is crucial in this context. The influence of grain size and grain boundary characteristics on out-plane thermal conductivity for <111>-oriented CVD 3C–SiC was discussed in this study. The out-plane thermal conductivity sharply decreases from 146.4 W/m⸱K to 122.3 W/m⸱K when the grain size approaches 11.04 μm. This paper suggests that the significant accumulation of dislocations at high-angle grain boundaries is the primary cause of this phenomenon. The substantial lattice strain impedes phonon transfer between grain boundaries, reducing overall phonon mobility. These findings suggest that manipulating the grain boundary angle is an effective means to fine-tune heat transfer in <111>-oriented CVD 3C–SiC. [ABSTRACT FROM AUTHOR]

In this paper, we propose a second-order adaptive DLN algorithm with different subdomain variable time steps for the 3D closed-loop geothermal system. Theoretically, the stability and convergence of the algorithm in the case of variable time steps are analyzed. In numerical experiments, the DLN algorithm is combined with an adaptive algorithm to verify not only its effectiveness and second-order convergence under any arbitrary sequence of time steps but also to improve computational efficiency. We overcome the difficulty of 3D programming, and verify the applicability and accuracy of the proposed algorithm by simulating the flow characteristics and heat transfer of the closed-loop geothermal system with 3D convection. [ABSTRACT FROM AUTHOR]

The non-Fourier heat transfer model has gained significant attention in practical engineering applications, particularly under extreme conditions. However, solving the three-dimensional non-Fourier hyperbolic heat conduction equation remains a challenge. A method for solving the three-dimensional Maxwell-Cattaneo-Vernotte hyperbolic heat conduction equation on unstructured grids is proposed, where the total diffusion term is divided into normal diffusion term and cross diffusion term, and the temperature gradient is solved by reconstruction gradient. The convergence and accuracy of this method are verified by calculating the heat transfer process of a three-dimensional hollow cylinder, and the numerical solutions are found to be consistent with existing analytical solutions. Furthermore, the effects of relaxation time on the non-Fourier heat transfer process in three-dimensional hollow cylinder and complex ceramic part are discussed. Importantly, the method presented in this paper is not influenced by the coordinate system or the shape of the calculated region, providing a theoretical reference for solving complex three-dimensional non-Fourier heat transfer problems. [ABSTRACT FROM AUTHOR]

In this paper, we proposed a novel collocation method to solve nonlinear transient heat transfer problems in typical intelligent materials. The new method is derived from the weighted residual method in which the weight of Jacobian is proven to be the best choice. In the paper, the physical variables and their fluxes are respectively approximated by two series of Lagrange interpolation polynomials at Chebyshev-Gauss-Lobatto nodes. In the proposed method, the mass matrices of the final linear system of equations are diagonal and the explicit time discretization method can be employed. Using the proposed method, we solved the heat transfer in intelligent materials and it is proven to be quite efficient and accurate, which benefits from that no large sparse matrix is generated and solved. By the proposed method, one can easily solve the problems with complex geometries. [ABSTRACT FROM AUTHOR]

• The nonlinear dynamics and thermal bidirectional coupling model of a rotor-ball bearing system is constructed. • The coupling characteristics of the interaction between vibration response and temperature variation are obtained. • The complicated jump phenomena and motion patterns in vibration response and temperature variation are demonstrated. • The characteristics affected by initial radial clearance, rotor eccentricity and lubricant viscosity are discussed. This paper focuses on the nonlinear dynamics and thermal bidirectional coupling characteristics of a rotor-ball bearing system. The motion equations of the rotor system are formulated by the Lagrange method, where the radial clearance of the ball bearing affected by thermal characteristics is considered. The heat transfer model of the ball bearing is established by combining the lumped parameter with the full thermal network, in which the frictional heat generation induced by the dynamic load of the ball bearing is considered. The heat transfer model is coupled with the motion equations of the rotor system via the mechanical model of the ball bearing. The dynamics and thermal bidirectional coupling model is solved by the step-by-step iterative solving procedure to detect the interaction between the vibration response of the rotor and the temperature variation of the ball bearing. The results show that the thermal expansion of the ball bearing results in the dynamical variation of the effective radial clearance, which makes a significant influence on nonlinear dynamics and thermal characteristics of the rotor-ball bearing system. On the other hand, the nonlinear dynamic response of the rotor leads to the nonlinear thermal characteristics of the ball bearing through the influence of the dynamic load. It is observed that there are more complicated jump phenomena and motion patterns in the vibration response and temperature variation compared to the case without thermal effects. Moreover, the jump phenomena affected by the initial radial clearance, rotor eccentricity, and lubricant viscosity are analyzed in detail. The results obtained in this paper can provide more insight into the bidirectional coupling mechanism of the nonlinear dynamics and thermal characteristics. [ABSTRACT FROM AUTHOR]

Abstract: Effects of suction pressure and permeability on the steam heating characteristics of the wet paper are studied. Experimental results show that suction pressure enhances the energy absorption in the wet paper and effects of suction pressure strongly appear in the high-permeability paper, and also absorbed energy rate is decreased with increasing in heating time. From the numerical simulation results it is found that increase in moisture content and decrease of pressure gradient reduce the absorbed energy rate. Dimensionless numbers are derived from the basic equations to summarize the experimental and numerical simulation results. [Copyright &y& Elsevier]

Abstract: The paper gives a progress report on a theoretical study of film condensation in microchannels. The model takes account of surface tension, vapor shear stress and gravity. The effect of channel shape is investigated for condensation of R134a in channels with cross sections: square, triangle, inverted triangle, rectangle with longer side vertical, rectangle with longer side horizontal and circle. The case considered here is where the channel wall temperature is uniform and the vapor is saturated at inlet. For a given mass flux, the local condensate film profile around the cross section is calculated together with the mean heat-transfer coefficient at different distances along the channel. Results are presented here for one vapor mass flux, one vapor temperature and one wall temperature. [Copyright &y& Elsevier]

Abstract: In this paper we study the heat transfer and fluid flow in a step-down 3-phase power transformer. In order to simplify the study we choose an element composed of two windings wound around a core. The Joule effect and the Foucault currents produce an undesirable heat in the different components of the transformer. From an economical and security point of view, there is a need to cool the transformer to preserve it from destruction. Our main objective is the cooling optimization of the power transformer. In order to attain this goal, a numerical study has been conducted for six different geometric configurations with six different flow rates of the cooling oil at the entrance. The physical properties of the fluid are supposed to be function of the temperature. The control volume method has been used to resolve the continuity, the momentum and the energy equations in the steady state. The obtained results show that the structure of the flow is somehow complex and according to the case some rolls appear at the top and the bottom of the windings, these rolls contribute to a good mixing of the fluid leading to a nearly homogeneous temperature. [Copyright &y& Elsevier]

Abstract: In the finite volume approach for incompressible flow and heat transfer, the discretization of the convection term and the treatment of the coupling between velocity and pressure are the two major issues affecting solution stability, accuracy and convergence rate. In this review paper, some recent advances made in the CFD/NHT & Enhanced Heat Transfer Center of Xi''an Jiaotong University, China, are presented and their applications in the study of heat transfer enhancement are also briefly summarized. [Copyright &y& Elsevier]

The current technologies to treat hypersaline produced water (PW), such as thermal evaporation, are usually energy-intensive and cost-prohibitive. This study developed a low-cost, robust, solar-driven carbon black and airlaid paper-based evaporator (CAPER) for desalination of PW in the Permian Basin, United States. The study aims to better understand the removal of aromatic organic compounds and heavy metals during solar distillation, water output, and heat transfer. Outdoor experiments using CAPER assisted with polystyrene foam in a single slope, single basin solar still achieved an enhanced average evaporation rate of 2.23 L per m2 per day, 165% higher than that of a conventional solar still. Analysis of heat transfer models demonstrated that CAPER solar evaporation achieved an evaporative heat transfer coefficient of ∼28.9 W m−2·K−1, 27.9% higher than without CAPER. The maximum fractional energy of evaporation and convection heat transfer inside the solar still with and without CAPER was ∼81.4% and ∼78.2%, respectively. For the PW with a total dissolved solids concentration of 134 g L−1, solar distillation removed 99.97% salts and over 98% heavy metals. The high removal efficiency of 99.99% was achieved for Ca, Na, Mg, Mn, Ni, Se, Sr, and V. Organic characterization revealed that solar distillation removed over 83% aromatic compounds. Solar desalination using CAPER provides a low-cost and high-performance process to treat PW with high salinity and complex water chemistry for potential fit-for-purpose beneficial uses. Image 1 • A carbon black and airlaid paper-based solar evaporator (CAPER) was developed. • Outdoor distillation of produced water (PW) achieved evaporation of 2.23 L m−2·d−1. • The evaporation rate of PW with CAPER is 165% higher than without CAPER. • Heat transfer coefficient with CAPER is 27.9% higher than without CAPER. • 99.97% salts, 98% metals, >83% aromatic compounds removed from 134 g L−1 TDS PW. [ABSTRACT FROM AUTHOR]

This comment concerns a rightful doubt involved in the above paper. In the reviewed article, a novel model without empirical constants was proposed to evaluate the effective thermal conductivity of three-phase soils, and such a model was claimed to be workable for soils with porosity ranging from 0.0349 to 0.4764 at all saturation degrees. However, sufficient reasons and pictorial explanations were given in this comment to prove its inapplicability for high degrees of saturation. Besides, the inapplicable range is constantly changing, depending on the porosity, i.e. the larger the porosity, the smaller the inapplicable saturation region. Similar issues were further discussed due to its great influence on the follow-up research in this field, i.e. whether can achieve a full coverage of the applicable saturation range [0,1] for a given porosity. [ABSTRACT FROM AUTHOR]

Abstract: Three-dimensional numerical simulations of the laminar flow and heat transfer of water in silicon microchannels with non-circular cross-sections (trapezoidal and triangular) were performed. The finite volume method was used to discretize the governing equations. Numerical results were compared with experimental data available in the literature, and good agreements were achieved. The effects of the geometric parameters of the microchannels were investigated, and the variations of Nusselt number with Reynolds number were discussed from the field synergy principle. The simulation results indicate that when the Reynolds numbers are less than 100, the synergy between velocity and temperature gradient is much better than the case with Reynolds number larger than 100. There is an abrupt change in the intersection angle between velocity and temperature gradient around . In the low Reynolds number region the Nusselt number is almost proportional to the Reynolds number, while in the high Reynolds number region, the increasing trend of Nusselt number with Reynolds number is much more mildly, which showed the applicability of the field synergy principle. In addition, for the cases studied the fully developed Nusselt number for the microchannels simulated increases with the increasing Reynolds number, rather than a constant. [Copyright &y& Elsevier]

Abstract: A series of tests have been carried out with a miniature loop heat pipe (mLHP), which has been developed for consumer electronics cooling, for horizontal and four vertical orientations under different sink temperatures. The mLHP has a cylindrical evaporator of 5 mm outer diameter and 29 mm length. The steady-state operating characteristics are similar for different orientations except for the orientation where the evaporator is above the compensation chamber. At an evaporator temperature of 75 °C, an evaporator heat load up to 70 W can be reached with thermal resistance of about 0.2 °C/W. The transient behavior of the mLHP is studied in detail. In general, the mLHP can be started up with very low power input (5 W). Big temperature oscillations in the liquid line were found in many cases, however, the temperature oscillations in the evaporator are minimum. The orientations greatly influence the operating characteristics of the mLHP. At least for the horizontal orientation, the overall performance of the tested mLHP is satisfying. [Copyright &y& Elsevier]

Abstract: A great variety of flows in practical engineering applications are inherently unsteady, and virtually all of Newtonian fluid flows in nature are turbulent. In order to better capture the dynamics of such complex flows, it is appropriate to use unsteady methods. The present overview is confined to single-phase turbulent flows. The first part provides an evaluation of the performance of the unsteady RANS (URANS) method. It could be confirmed that the U-RANS method employing a full Reynolds stress model is able to capture unsteady phenomena, such as precessing vortex core phenomenon both qualitatively and in parts also quantitatively. In the second part, some important features of combustion LES are recollected and some results for flames, that were already computed by RANS-based methods in the literature, are presented. Thereby a flamelet approach is used to relate the filtered mixture fraction to density, temperature and species concentrations. It is shown that LES is able to deliver good results very close to measured data, where the flow is governed by large, turbulent structures. Flamelet chemistry appears well able to reproduce experimental data for species, in particular with regard to kinetic effects prediction, whereas equilibrium chemistry strongly deviates. However, a good predictability could be achieved when appropriate choice of boundary and inflow conditions is made. [Copyright &y& Elsevier]

Abstract: The theoretical basis and conceptual formulation of a comprehensive reactor model to simulate the thermal-fluid phenomena of the PBMR reactor core and core structures is given. Through a rigorous analysis the fundamental equations are recast in a form that is suitable for incorporation in a systems CFD code. The formulation of the equations results in a collection of one-dimensional elements (models) that can be used to construct a comprehensive multi-dimensional network model of the reactor. The elements account for the pressure drop through the reactor; the convective heat transport by the gas; the convection heat transfer between the gas and the solids; the radiative, contact and convection heat transfer between the pebbles and the heat conduction in the pebbles. Results from the numerical model are compared with that of experiments conducted on the SANA facility covering a range of temperatures as well as two different fluids and different heating configurations. The good comparison obtained between the simulated and measured results show that the systems CFD approach sufficiently accounts for all of the important phenomena encountered in the quasi-steady natural convection driven flows that will prevail after critical events in a reactor. The fact that the computer simulation time for all of the simulations was less than three seconds on a standard notebook computer also indicates that the new model indeed achieves a fine balance between accuracy and simplicity. The new model can therefore be used with confidence and still allow quick integrated plant simulations. [Copyright &y& Elsevier]

In this paper, we study the magnetohydrodynamic (MHD) flow and heat transfer of the fractional Jeffrey fluid in a straight channel, of which the cross section is a two-dimensional irregular convex domain. We consider a spatial fractional operator to modify the classical Fourier's law of thermal conduction, and obtain the time-space fractional coupled model. The fractional coupled model is solved numerically by the L 2 − 1 σ method in the temporal direction and the unstructured mesh finite element method in the spatial direction. Besides, we prove the stability and convergence of the numerical scheme. In order to reduce the computational time, a fast method is proposed. Finally, a numerical example is given to verify the theoretical analysis and the efficiency of the fast method. Furthermore, an example is considered to discuss the effects of the fractional parameters on the MHD flow and heat transfer of the fractional Jeffrey fluid. [ABSTRACT FROM AUTHOR]

• Time-varying buckling and post-buckling of tapered columns in fire. • Temperature-dependent material properties. • The convective–radiative condition. • Geometric nonlinearity and yield strength. • Effects of transient localised fire on the tapered column. This paper presents time-varying flexural buckling and post-buckling responses of tapered columns under a transient fire of which the temperature is non-uniform along the length. First, the transient temperature field within the column is determined by solving a dimensionally reduced transient heat transfer problem considering the convection-radiation boundary conditions and temperature-dependent (TD) material properties. Subsequently, the von Kármán geometric nonlinear theory is applied to obtain the nonlinear equilibrium equation. The nonlinear heat transfer and equilibrium equations are solved by the differential quadrature (DQ) method. According to a yield criterion, the ultimate load at which the material failure occurs is predicted. The influences of a transient localised fire on the temperatures, buckling and post-buckling responses of tapered steel tubular columns are discussed. [ABSTRACT FROM AUTHOR]

Abstract The present comment concerns some doubtful results included in the above paper. [ABSTRACT FROM AUTHOR]

The diffusion characteristics of liquid kerosene in a supersonic combustor equipped with a thin strut under the effect of evaporation and combustion heat-release were discussed in this paper. A series of experiments and numerical simulations were carried out both in cold inflow (T t = 300 K) and high enthalpy inflow (T t = 1680 K). The experimental data of kerosene diffusion and combustion were captured by high-speed camera and schlieren equipment. Based on the Euler-Lagrangian method, the evaporation and diffusion process of liquid kerosene under different inflow and heat-release conditions were studied. Through the analysis of the basic data of the ground test and numerical simulation, the kerosene diffusion and penetration depth were obtained and analyzed. The results showed that the diffusion of kerosene vapor is affected by both the injection momentum and the evaporation momentum. The evaporation of liquid kerosene could effectively improve the penetration depth of kerosene vapor, and the maximum proportion could reach 60%. The combustion heat-release greatly enhanced the diffusion ability of kerosene vapor by increasing evaporation strength of liquid kerosene and pressure in the heat-release zone, and the diffusion and combustion of kerosene were positively coupled with each other. With the investigation in this paper, a mechanism on kerosene diffusion in the supersonic combustor was explained. • Kerosene diffusion characteristics were analyzed with evaporation characteristics. • Evaporation momentum was defined and effect on kerosene diffusion was discussed. • The enhancement of kerosene diffusion with combustion heat-release was discussed. [ABSTRACT FROM AUTHOR]

On-orbit Servicing in the form of space-manufacturing, refuelling, assembly and robotic manipulation are deemed to become a fundamental part of the space market in the short-to-middle term. One of the key aspects to reach extensive use of OOS operations is having a standardized, reliable, and cost-effective interface that embeds as much functionality as possible to simplify operations. In this context, SENER Aeroespacial has developed SIROM (Standard Interface for Robotic Manipulation), which provides mechanical coupling, electric interface, thermal and data transfer in a single compact solution. In this paper, the current design for SIROM is presented, with a focus on the electronics subsystem and the integration of the electromechanical design. A functional breakdown of the electronic boards is presented after a review of the current state of the art. For the validation, a TRL6 Test Campaign that was successfully passed in early 2021, including vibration, temperature, vacuum and life tests. Its results are presented here, along with the details of the functional validation on the context of the EROSS project in May/June 2021. To conclude the paper, on-going projects involving the SIROM interface are reviewed, finishing with future lines of development on the SIROM roadmap. • On Orbit Servicing is becoming a fundamental part of the space market. • SENER designed the SIROM interface for this purpose, developing a fully integrated model in 2021. • SIROM has passed a qualification campaign for Technology Readiness Level 6. • SIROM has been validated in the H2020 project EROSS in an On Orbit Servicing scenario. • SIROM is developing to reach TRL 8 as part of European projects (MIRROR, PERIOD). [ABSTRACT FROM AUTHOR]

Abstract The search for lightweight, flexible, thermally stable and thermally conductive materials with good electromagnetic interference (EMI) shielding ability remains the most serious prospect in recent years. Herein, a polyacrylonitrile (PAN) based multi-phase system is fabricated using hollow cenospheres (CS), mesocarbon microbeads (MCMB) and multiwall carbon nanotubes (MWCNTs) with or without iron oxide via homogenization and vacuum assisted filtration technique. Resulting composite paper is stabilized to provide enough strength to the composite paper with thickness 0.18 mm and density 0.31–0.33 g/cm3 which can vary in accordance with cenospheres loading. Composite paper exhibits very high EMI SE value of −75.6 dB on 20 wt% cenospheres loading while a synergistic effect of dual dielectric (CS) and magnetic (iron oxide) materials in the composite paper, results in excellent EMI shielding value of −80.5 dB at a frequency of 10.3 GHz. Furthermore, the composite paper shows good thermal stability and enough thermal conductivity required for proper heat transfer management. Therefore, the development of multi-functional composite paper in one entity may get benefits of excellent EMI performance, good thermal stability and significant heat dissipation capability with the advantage of lightness and flexibility. Graphical abstract Free standing, flexible and light weight hybrid composite paper was developed by simple strategy using cenospheres and iron oxide nanoparticles as filler in a mesocarbon microbeads and multiwall carbon-nanotubes based matrix which exhibits exceptional EMI SE of −80 dB in X-band with efficient heat dissipation ability. Image 1 [ABSTRACT FROM AUTHOR]

This paper mainly analyzes the heat transfer of Carreau fluid over an infinite rotating disk, and two models with variable thermal conductivity are considered. Firstly, the governing partial differential equations (PDEs) are transformed into ordinary differential equations (ODEs) by similarity transformation. Then, the boundary value problem is solved by improved bvp4c method, which reduced sensitivity to the initial values. For shear-thinning and shear-thickening fluids, the effects of Carreau fluid index n and Prandtl number Pr on velocity and temperature fields are shown and analyzed when 0.5 ≤ n ≤ 1.5 , 1 ≤ P r ≤ 10. Furthermore, the thermal conductivity is computed under two cases. [ABSTRACT FROM AUTHOR]

Despite extensive investigations on the mechanism of laser-irradiated solid propellants, formulating an accurate model that characterizes more details of laser-target interactions remains a challenging task. In this paper, a thermal model for nanosecond pulsed laser ablation of aluminum was developed using the finite volume method which considers the instant recession on the propellant surface and the non-Fourier effect during heat conduction. The robust coupling iteration scheme adopted in the model tracks the dynamic boundary condition due to instant propellant removal. In particular, the pre-qualified threshold is used as discriminator for phase explosion and the thermal relaxation time is introduced to quantify the non-Fourier effect on heat conduction. In addition, the temperature-dependent physical and optical parameters of the propellant were also regarded in the proposed model. The numerical implementations for Gaussian laser ablation of aluminum were performed at different laser fluences and thermal relaxation times. The theoretical computation of the ablation depth coincides well with the experimental results to validate the feasibility of the model. • The thermal interaction of an ultra-short pulsed laser with metal was investigated. • The material moving front during heat transfer was modeled using finite volume method. • A modified critical threshold was used as a discriminator for metal phase explosion. • The thermal relaxation time was introduced to quantify the non-Fourier effect. [ABSTRACT FROM AUTHOR]

• The comment concerns a paper published in Chemical Engineering Science Journal. • The problem is non-similar. However the authors treated the problem as similar. • In non-similar problems one x-dependent parameter is used. The authors used three. [ABSTRACT FROM AUTHOR]

Two mistakes exist in [1]. [ABSTRACT FROM AUTHOR]

This paper describes an accurate model of the Electrical Power Subsystem (EPS) of the Thermal Analysis Support and Environment Characterization Laboratory (TASEC-Lab), a university experiment developed for using in high-altitude balloon missions to measure and analyze the convection heat transfer. A Li-ion battery and two high efficient DC–DC converters have been characterized through laboratory tests and fitting to the experimental results. The developed mathematical models described in this paper are used to carry out accurate EPS simulations and are validated by comparison with the experimental data. • Design and modeling of the electrical power subsystem of a stratospheric balloon experiment. • New Li-lion battery discharging model that describes the three main parts: initial decay, linear, and exponential decay. • Formulation of a new DC/DC converter efficiency model. • Simulation and model validation of the electrical power subsystem. [ABSTRACT FROM AUTHOR]