Search

Magnetically coupled impedance-source (MCIS) networks are recently introduced impedance networks intended for various high-boost applications. It employs coupled magnetic in the circuit to achieve higher voltage gain. Various MCIS networks have been proposed in the literature for myriad applications; however, due to effective role of system modeling in the closed-loop controller design, this paper is allocated to small-signal modeling and analysis of MCIS converters. The modeling is performed by means of the circuit averaging and averaged switch technique. A generalized small-signal derivation is demonstrated for pulse width modulation (PWM) MCIS converters and it is shown that the derived transfer functions can simply be applied to Y-source, Γ-source, and T-source impedance networks. Various transfer functions for capacitor voltage, output voltage, magnetizing current, input and output impedance are derived and have been validated through frequency and dynamic responses of computer simulation results. In addition, a comprehensive analysis has been done for all mentioned PWM MCIS converters regarding their circuit parameters. Furthermore, the effect of considering the equivalent series resistances of capacitor and inductor on the stability margin of MCIS converters is revealed in this paper. Finally, in order to validate the derived transfer functions and to consolidate the perfumed analysis, experimental results are presented for all mentioned MCIS converters. [ABSTRACT FROM PUBLISHER]

A multilevel H-bridge StatCom inherently contains redundancy in the available switching states. This paper develops a variation on the typical model predictive control scheme which is able to exploit this redundancy to simultaneously balance the H-bridge capacitor voltages, provide excellent current reference tracking, and minimize converter switching losses. The scheme consists of a dead-beat current controller that has been integrated with heuristic models of the voltage balancing and switching loss characteristics. The integration of a pulsewidth modulation scheme is also described. Simulation and experimental results are presented that confirm the correct operation of the control and modulation strategies. Comparison with traditional control and modulation schemes is provided in terms of the key performance indicators associated with multilevel H-bridge StatComs. [ABSTRACT FROM AUTHOR]

This paper presents a sinusoidal pulsewidth modulation (SPWM) based direct digital control with average-voltage model (AVM) and division–summation process for paralleled three-phase three-wire (3φ3W) grid-connected converters to reduce circulating currents. With the direct digital control, plant of each single-phase converter can be derived directly, and a controller is then designed to cover the variation effects of filter inductance and grid voltage. Based on SPWM and AVM over a switching cycle, each 3φ3W converter can be decomposed into three single-phase converters and each converter is controlled individually to track its sinusoidal reference current tightly, reducing circulating currents significantly. Equal current sharing is therefore also achieved. The control laws for achieving grid connection are derived in detail. In the design and implementation, the inductances corresponding to various inductor currents are measured offline and stored in the controller for scheduling loop gain cycle by cycle. Experimental and simulated results from a three-converter system confirm the analysis and discussion of the proposed control approaches. [ABSTRACT FROM AUTHOR]

A trinary multilevel converter uses a few heterogeneous H-bridge submodules (SMs) to synthesize an output voltage with multiple levels. Two major limitations of this converter are that it needs multiple dc sources and it cannot operate under pulsewidth modulation (PWM). This paper addresses these limitations by adding a low-voltage H-bridge SM to this converter and proposing a new switching algorithm. The resulting PWM-based asymmetric cascaded H-bridge converter uses only one dc source and synthesizes a high-quality output voltage. This improved converter can be a potential choice for real and reactive power support in power system applications. This paper also proposes methods for stability analysis and design of this converter. Experimental case studies evaluate the performance of the proposed converter for both standalone and grid-connected modes of operation. [ABSTRACT FROM AUTHOR]

This paper presents the active capacitor voltage-balancing (ACVB) methods based on the dynamic model for a five-level nested neutral-point piloted (NNPP) converter using hybrid carrier modulation. The traditional hybrid carrier modulation provides natural voltage balancing of floating capacitors and dc-link capacitors. First, the natural voltage-balancing ability under steady-state and ideal conditions is theoretically proved. However, there are accumulated errors and deviations of capacitor voltages in practical applications, especially under dynamic conditions. In order to address the accumulated errors and deviations of capacitor voltages, the dynamic models of floating-capacitor voltages and neutral-point voltage are established. Moreover, the ACVB method based on the dynamic model of the neutral-point voltage is proposed by injecting the zero-sequence voltage. And the ACVB method based on the dynamic model of floating-capacitor voltages is proposed by introducing the adjustment variables. The proposed ACVB methods have the advantages of simple formula, definite physical meaning, and high accuracy. Furthermore, the output voltage quality and current quality are evaluated in term of total harmonic distortion and the effect of model parameter mismatch on the proposed ACVB methods is presented. Finally, the comparative simulation and experimental results verify the correctness of the proposed ACVB methods based on the dynamic model under different conditions. [ABSTRACT FROM AUTHOR]

The five-level active neutral-point-clamped (5L-ANPC) converter has been widely studied for its excellent performance in high-power medium-voltage applications. This paper analyzes the space vector pulse width modulation (SVPWM) strategy of the 5L-ANPC converter in the virtual coordinate, and presents an optimized control strategy which can balance the neutral point (NP) voltage and avoid the dead-time effects for the first time. In this strategy, on one hand, the 125 space vectors are combined by 96 triangles in the seven-segment vector synthesis method, then the triangles are divided into seven categories which have different characteristics of balancing the NP voltage, and every category has its own principles to choose the vector sequence and compute the vector durations. On the other hand, the dead-time effects of the 5L-ANPC converter are studied in detail and the transitions between different switching states are constrained in the optimized control strategy to avoid the dead-time effects that cannot be compensated by traditional pulse-based dead-time compensation methods. Finally, the optimized SVPWM strategy is experimentally verified in this paper. [ABSTRACT FROM AUTHOR]

Compensation of nonlinear effects generated by dead-time and semiconductors voltage drop has been widely studied in the literature about two-level converters. This paper takes a closer look at those analyses for multilevel converters, specifically for a cascaded H-bridge (CHB) converter modulated with phase-shifted pulse width modulation. The interaction between the cells is analyzed for a generic $n$ -cell converter, from which a general expression for the distortion generated by the nonlinearities has been obtained. Based on this expression, a compensation signal for the overall converter is calculated on each sample time, which is a fraction of the triangular carrier used to modulate each cell, thus significantly improving the quality of the output voltage signals. Experimental validation of the proposed compensation method is presented using a three-phase four-cell CHB converter prototype of 5.5 kW. [ABSTRACT FROM AUTHOR]

In this paper, the concept of a modulated-ramp pulse-width modulation (PWM) generator is presented. The specific nonlinear behavior of this generator enables an exact linear control-to-output static conversion characteristic of DC-DC switching converters, such as the boost (step-up), buck/boost, Ćuk, or SEPIC, operating in continuous conduction mode. The resulting linearization leads to a significant improvement of the control accuracy and simplification of the converters, operating mainly in the open-loop architecture. In this paper, the concept of the modulated-ramp PWM generator is described, followed by a detailed steady-state and small-signal AC analysis. The key aspects for practical implementation are also highlighted. All results and benefits of the modulated-ramp PWM generator are demonstrated here on the boost converter power stage. [ABSTRACT FROM AUTHOR]

Multilevel cascaded H-bridge converters have found industrial application in the medium-voltage high-power range. In this paper, a generalized modulation technique for this type of converter based on a multidimensional control region is presented. Using the multidimensional control region, it is shown that all previous modulation techniques are particularized versions of the proposed method. Several possible solutions to develop a specific implementation of the modulation method are addressed in order to show the potential possibilities and the flexibility of the proposed technique. In addition, a feedforward version of this technique is also introduced to determine the switching sequence and the switching times, avoiding low harmonic distortion with unbalanced dc voltages. Experimental results are shown in order to validate the proposed concepts. [ABSTRACT FROM AUTHOR]

A new zero-voltage-switched bidirectional dc–dc converter with coupled inductors is proposed in the paper. The proposed converter can operate with a steep conversion ratio, soft switching, a continuous inductor current, and fixed switching frequency. It can also operate with the switch stresses of a conventional pulsewidth-modulation-tapped/coupled-inductor converter regardless of the direction of power flow and without any voltage spikes across the switches during turn-OFF. These features are due to a very simple auxiliary circuit that is operational regardless of the direction of power flow and absorbs energy from the leakage inductance of the coupled inductors during switch turn-OFF. In the paper, the operation and design of the converter are discussed and its feasibility is confirmed with experimental results obtained from a prototype. [ABSTRACT FROM PUBLISHER]

Semiactive quadrupler rectifiers (SAQRs) are proposed in this paper to serve as the secondary rectification circuits, which make the secondary-side voltages to be controllable and help reduce current stress and conduction losses. An interleaved isolated boost converter is developed based on the proposed SAQRs. By utilizing the pulse-width modulation (PWM) plus phase-shift (PPS) control strategy, the primary- and secondary-side voltages are well matched to reduce the current values and circulating conduction losses. With the proposed SAQRs, the voltage gain is extended and the voltage stresses on power devices and passive components used in rectification circuits are reduced to the half of the high output voltage. Hence, the efficiency is improved by using a transformer with a smaller turns ratio and reduced parasitic parameters, and by employing low-voltage rating devices with better switching and conduction performance. With optimal design, lower voltage, and current stresses on the primary-side switches, minimized input current ripple can be realized. Moreover, the zero-voltage turn on switching of the active switches and the zero-current turn off switching of the diodes can be achieved over a wide load and voltage range by the proposed SAQR-based converter and the control strategy. Meanwhile, the higher voltage gain, the lower voltage, and the current stresses on power devices can be obtained with the proposed SAQR-based converter compared with passive quadrupler rectifier-based converter. The feasibility and effectiveness of the proposed SAQRs and the derived converter are verified by a 380-V output prototype. [ABSTRACT FROM PUBLISHER]

This paper presents a new space vector pulsewidth modulation scheme to reconstruct phase currents using neutral-point current sensing in three-level T-type converters (TLTTCs). For this purpose, zero vector and offset vectors are replaced with complementary active vectors. These active vectors do not affect the resultant output voltage and the voltage balance at the neutral point of TLTTCs. Hence, the pulsewidths of corresponding active vectors can be adjusted even at low speeds without much additional switching losses and low-frequency noise in the inverter. The modified switching patterns can easily be generated without significant computational complexity. The proposed method is experimentally verified using Texas Instruments TMS320F28335 and Spartan 6 controllers, on a custom designed T-type converter based on Fuji IGBT modules. [ABSTRACT FROM PUBLISHER]

A novel complementary phase disposition pulsewidth modulation method for the modular multilevel converter (MMC) with a limited number of submodules is proposed in this paper. Compared with the previous works, more practical issues have been considered, and the corresponding solutions have been provided. First, a new preset PWM signal mapping sequence and an improved virtual loop mapping (VLM) are used in the modulation. This method not only achieves a favorable capacitor voltage balance in the symmetry system but lowers the switching frequency of MMC's devices. Second, to further reduce the switching frequency, the unbalance margin of capacitor voltages is adopted to achieve the switching between the VLM and the selective VLM (SVLM). Moreover, the system robustness has been improved by considering the situation of symmetry losing, like cell fails; in these cases, the capacitor voltages of the upper and lower arms are balanced through the collaboration of the SVLM and the reconfigurable VLM. Finally, the effectiveness of the proposed method has been verified with simulation and experimental studies. [ABSTRACT FROM AUTHOR]

In this paper, a family of three-phase direct pulse-width modulated (PWM) ac–ac converters consisting of buck, boost, and buck–boost converters is proposed. The proposed converters have no commutation problem even if all of the switches are turned on or off simultaneously. They do not use lossy snubbers and do not sense the voltage polarity for commutation, and produce high-quality output voltage waveforms. The proposed converters allow the use of power MOSFETs and fast recovery freewheeling diodes independently. The use of power MOSFETs as active switches and freewheeling diodes with extremely fast recovery features lower the switching losses and enable us to reduce the volume of passive components by increasing switching frequency. The input (or output) filter inductor experiences twice of the converter switching frequency and thus can be designed with minimum size. To increase power density of the proposed converters, a three-phase three-limb coupled inductor is proposed. Three-phase coupled inductor integrates three separate coupled inductors of the proposed converters in one three-limb core. In comparison with separate coupled inductors, the three-phase coupled inductor has a smaller size with large current-handling capability. Experimental results obtained for the boost-type converter show the robustness of the proposed three-phase ac–ac converters. [ABSTRACT FROM AUTHOR]

This paper proposes a hybrid modulation strategy for asymmetrical cascaded multilevel converters operating under normal and faulty conditions on power cells. The proposed algorithm explores the advantages of both space vector (SV) and carrier-based modulation approaches. An SV is used for higher voltage cells to properly choose their voltage vectors in a way such as to avoid converter saturation, particularly under fault conditions. A generic algorithm to identify the domains of higher voltage vectors in which a reference lies, without the need for separation lines, is proposed. Then, to simplify the implementation of the algorithm, carrier-based modulation is employed for lower voltage cells, which switch with pulsewidth modulation. This suppresses the need for defining multiple switching sequences for different operational conditions, and it avoids converter saturation as much as possible, particularly under fault conditions on power cells. Simulation and experimental results for normal and faulty operational conditions are given, validating the theoretical analysis and demonstrating the good performance of the proposed hybrid modulation approach. [ABSTRACT FROM AUTHOR]

Many publications have been presented on the modulation and control of the modular multilevel converter, some of which are based on phase-shifted carrier modulation. This paper presents an analysis of how the switching frequency affects the capacitor voltages, circulating currents, and alternating voltages using phase-shifted carrier modulation. It is found that switching frequencies that are integer multiples of the fundamental frequency should be avoided as they can cause the capacitor voltages to diverge. Suitable switching frequencies are derived for which the arm and line quantities will be periodic with symmetric operating conditions in the upper and lower arms. Thus, the practical outcome of this paper is a detailed description of how the switching frequency should be chosen in order to achieve advantageous operating conditions. The theoretical results from the analysis are validated by both simulations and experimental results. [ABSTRACT FROM AUTHOR]

This paper proposes a voltage balancing method for a flying capacitor multilevel converter based on the phase-disposition sinusoidal pulsewidth modulation (PD-SPWM). This voltage balancing method uses redundant switching states, which are determined by the minimization of a cost function. The implementation of the PD-SPWM using standard triangular carriers leads to additional switching events that are due to the transitions within the same voltage level, thus increasing the switching frequency of the power devices. Such drawback can be avoided by using sawtooth carrier waveforms. Another characteristic of the proposed voltage balancing method is that it does not require the tuning of parameters to achieve optimal performance. Simulation and experimental results confirm the robustness of the proposed method operating with different loads and transient conditions. [ABSTRACT FROM PUBLISHER]

This paper presents a buck-boost dc-dc converter for LED drivers capable of delivering an output current ranging from 0.1 to 2 A and a variable output voltage ranging between 2 and 5 V, starting from an input voltage spanning from 2.7 to 5.5 V. The dc-dc converter, realized in a 0.18-μm CMOS technology with 5-V option, occupies an area of 4 mm2 including pads. The circuit features automatic mode switching and dynamic sizing of the power transistors to achieve a peak efficiency of 91%. With a switching frequency of 2.5 MHz, the achieved line regulation is lower than 0.1% V-1 and the output voltage ripple is less than 10 mV. The obtained turn-on and load transient settling time are lower than 40 μs, thus allowing pulsed operation of the LEDs, as well as switching among LEDs of different colors. [ABSTRACT FROM AUTHOR]

Distributed energy resources (DERs) are expected to provide ancillary functions including reactive power generation and harmonics compensation. Meanwhile, multilevel inverters and two-level converters with optimal pulsewidth modulation (OPWM) will be commonly used for DERs at high power levels. The challenge is to realize harmonic compensation with limited switching angles. This paper presents an online solution to realize the selective harmonics compensation (SHC), and power generation with DERs. For harmonics compensation, the selective harmonic components in the load current are detected. Then, the harmonic voltages are provided with DERs to cancel out these detected components. Since the power converter is requested to realize both harmonics filtering and power generation, limitations on harmonics compensation at the given power are discussed. Power hardware-in-the-loop-based online verifications are shown at the end of the paper. [ABSTRACT FROM AUTHOR]

In this paper, a new single-stage half-bridge (HB) resonant $LLC$ converter additionally employing one resonant capacitor and two relays with one package is proposed, compared with a single-stage HB $LLC$ converter. Moreover, a center-tapped transformer is replaced with a coupled transformer. Since the proposed converter changes the turns ratio of the coupled transformer using a relay according to low- or high-input-voltage range, it can decrease the range of its needed voltage gain. It means that the proposed converter can be designed with large transformer magnetizing inductance compared with the conventional single-stage HB $LLC$ converter. As a result, the primary conduction and turn-off losses are reduced. Moreover, in low input voltage range, it has smaller total primary wire resistance of the transformer due to parallel connection of the coupled transformer, which decreases its conduction loss. In addition, additionally employed small-sized components can be inserted to the conventional system. To confirm the operation, features, and validity of the proposed converter, universal input with low line and high line and 16.5 V/60 W output laboratory prototype targeting laptop adapters with wide-input-voltage range is built and tested. [ABSTRACT FROM AUTHOR]

Power systems for exploration rovers tend to be complex as three separate converters are necessary; in addition to a main dc–dc converter and cell equalizer for rechargeable energy storage cells, an equalizer for photovoltaic (PV) modules is desirably equipped in order to preclude negative impacts of partial shading. This paper proposes the pulse width modulation (PWM) converter integrating voltage equalizers for PV modules and energy storage cells. The proposed integrated converter comprises a switched capacitor converter, PWM buck converter, and series-resonant voltage multiplier that perform PV equalization, power conversion from the PV modules to the load, and cell equalization, respectively. Three converters can be integrated into a single unit with reducing the total switch counts, achieving not only system-level but also circuit-level simplifications. The derivation procedure of the integrated converter is explained, followed by the operation analysis. Experimental tests were performed using series-connected supercapacitor (SC) modules and solar array simulators to emulate a partial shading condition. With the integrated converter, the extractable maximum power from the PV modules significantly increased while voltage imbalance of SC modules was adequately eliminated, demonstrating the integrated performance of the proposed converter. [ABSTRACT FROM AUTHOR]

Dynamic voltage restorer (DVR) technology has become a mature power quality product. In high-power applications, DVR using a multilevel converter is commonly used. However, DVR using a multilevel direct pulse width modulation (PWM) ac–ac converter has not been well studied. This paper presents a new DVR topology using a cascaded multilevel direct PWM ac–ac converter. In the proposed scheme, the unit cell of the multilevel converter consists of a single-phase PWM ac-ac converter using switching cell structure with coupled inductors. Therefore, the multilevel converter can be short- and open-circuited without damaging the switching devices. Neither lossy RC snubber nor a dedicated soft commutation strategy is required in the proposed DVR. This improves the reliability of the DVR system. The output voltage levels of the multilevel converter increase with the number of cascaded unit cells, and a high ac output voltage is obtained by using low-voltage-rating switching devices. Furthermore, a phase-shifted PWM technique is applied to significantly reduce the size of the output filter inductor. A 1-kW prototype of single-phase DVR is developed, and its performance is experimentally verified. Finally, the simulation results are shown for a three-phase DVR system. [ABSTRACT FROM AUTHOR]

Modular multilevel converter (MMC) is a newly emerging multilevel topology for high-voltage applications during recent years. In this paper, a new MMC is proposed, and the structure and operating principle are analyzed. Owing to the cascaded basic cells without multiwinding transformer, the voltage balancing of floating capacitors must be considered. However, the voltage fluctuation also exists, and theoretical analysis indicates that the amplitude is inversely proportional to the fundamental frequency. This paper has proposed a voltage-fluctuation-suppression method which can reduce the amplitude of the voltage fluctuation in low-frequency region. It can also be used in motor driving with pump/blowerlike load at low frequency and improve the start-up performance significantly. A low-power three-phase five-level prototype is designed and built up to demonstrate the validity of this method. [ABSTRACT FROM PUBLISHER]

The advancement in power electronics has made the use of any number of phases in ac machines possible since with the inverter, any number of phase voltages can be realized as long as the corresponding inverter exists. To supply multiphase drives requires multiphase voltage source inverters (VSIs) whose output voltages depend very much on the methods of generating the pulses to turn on and turn off the inverter devices appropriately. This paper presents an analytical technique for the determination of the expressions for the modulation signals used in the carrier-based sinusoidal and generalized discontinuous pulse width modulation schemes for two-level, five-phase voltage source converters. These expressions can be used for both balanced and unbalanced phase voltages generated by any two-level multiphase inverter, in generating the required reference signals appropriately. An example of a five-phase VSI is presented to illustrate the strategy. Simulation and experimental results are presented in which a close examination shows that both results are similar for the balanced and unbalanced load voltage cases. [ABSTRACT FROM AUTHOR]

This paper proposes a new circuit topology for a multilevel pulse width modulation (PWM) rectifier. The proposed method forms a new circuit by combining a diode clamp-type topology with a flying capacitor-type topology. The proposed circuit uses only 12 switches, despite the use of a five-level three-phase PWM rectifier. Further, the proposed circuit can obtain good performance, same as a conventional multilevel circuit. This paper describes about the features of the proposed topology; the control strategy and the loss analysis that is estimated by a circuit simulator. In addition, the basic operation of the proposed method is confirmed by simulation and experimental results. The proposed converter achieved total harmonic distortion of 3.4% for the input current and efficiency of 97.4% for a 1 kW class experimental setup. [ABSTRACT FROM AUTHOR]

This paper presents a neutral point voltage control strategy for the three-level active neutral point clamped (ANPC) converter using selective harmonic elimination pulsewidth modulation (SHE-PWM). The control strategy introduces a small change in the switching angles, which varies the duty cycle of the zero-level switching state, controls the neutral point current and, therefore, the neutral point voltage. The decision to vary a given switching angle takes into account the polarity of the output currents and the voltage across the lower dc-link capacitor. The effectiveness of the proposed strategy is verified through extensive simulation studies and experimentally validated using a low power laboratory prototype. [ABSTRACT FROM AUTHOR]

A matrix converter interfaces with three-phase ac voltage source, which creates three different virtual dc-link voltages. In this paper, a new pulsewidth modulation (PWM) method for the matrix converter is proposed to generally use these three virtual dc-link voltages. By using the two higher line-to-line voltages as the virtual dc-link voltages, the proposed method can create the identical switching sequences to those created by the conventional space vector PWM (SVPWM) method. Moreover, the proposed method is able to select the appropriate virtual dc-link voltage, according to the PWM purpose and/or load condition. In this paper, the virtual dc-link voltages adjacent to the output voltage reference are introduced to reduce output-current switching ripples. The feasibility of the proposed PWM method was verified by a computer simulation and experimental results. The output voltage and current waveforms produced by using the proposed method can be equal or better than those created using the conventional SVPWM method. Moreover, a new switching sequence that reduces output-current switching ripple can be easily adopted within the proposed PWM method. The harmonic characteristics of output current created using the proposed method are markedly improved over those using the conventional PWM method. [ABSTRACT FROM PUBLISHER]

Multiple output converters (MOCs) are widely applied to applications requiring various levels of output voltages due to their advantages in terms of cost, volume, and efficiency. However, most of the conventional MOCs cannot regulate multiple outputs tightly and they can barely avoid the cross-regulation problem. In this paper, the recently developed time-division multiple control (TDMC) method, which can regulate all of the outputs with a high accuracy, is used for a multiple output battery charger based on the phase-shift full-bridge topology to simultaneously charge three batteries. The proposed charger is able to charge three different kinds of batteries or three of the same kind of battery in different state of charges (SOCs) independently and accurately with the constant current/constant voltage (CC/CV) charge method. As a result, the strict ripple specification of a battery can be satisfied for multiple battery charges without difficulty. In addition, the proposed charger exhibits a high efficiency since the soft switching of all of the switches during the entire charge process can be guaranteed. The operating principle of the converter and the design of the controller, including the state-space average modeling, will be detailed, and the validity of the proposed method is verified through experiments. [ABSTRACT FROM PUBLISHER]

This paper proposes and evaluates an active voltage-balancing method for stacked multicell converters (SMCs) using phase-shifted pulse width modulation. The method is easy to implement and can be applied to SMCs with any number of levels. The proposed method balances the voltages of the capacitors by modifying the duty cycle of each switch of the SMC using a proportional controller. The direction of the output current and the crossed effect among the duty cycles of the switches is considered and used to improve capacitor voltage balance. The performance of the proposed voltage-balancing method is verified experimentally for different loads, such as linear and nonlinear loads, and under transient conditions. [ABSTRACT FROM PUBLISHER]

This paper proposes a bidirectional three-level LLC resonant converter with a new pulse width and amplitude modulation control method. With different control signals, it has three different operation modes with different voltage gains. Therefore, it can achieve wide voltage gain range by switching among these three modes, which is attractive for energy storage system applications needing wide voltage variation. The proposed topology operates with constant switching frequency, which is easy to implement with digital control, and it can achieve soft switching for all the switches and diodes in the circuit as a conventional LLC resonant converter. The performance of the proposed converter is validated by the experimental results from a 1-kW prototype with 20 A maximum output current. [ABSTRACT FROM PUBLISHER]

This paper proposes a simplified space vector modulation (SVM) scheme for multilevel converters. Compared with earlier SVM methods, the proposed scheme simplifies the detection of the nearest three vectors and the generation of switching sequences, and therefore is computationally more efficient. Particularly, for the first time, the proposed scheme achieves the same easy implementation as phase-voltage modulation techniques. Another superior characteristic of the proposed scheme over earlier methods is its potential for multiphase multilevel applications. The proposed scheme also offers the following significant advantages: 1) independence of the level number of the converter; 2) more degrees of freedom, i.e., redundant switching sequences and adjustable duty cycles, to optimize the switching patterns; and 3) no need for lookup tables or coordinate transformations. These advantages make the proposed scheme well suited to large level-number applications, such as modular multilevel converters and high voltage direct current systems. Simulation and experimental results verify this new concept. [ABSTRACT FROM PUBLISHER]

This paper proposes a novel single-phase ac–ac Z-source converter based on the Γ-structure. The proposed converter uses a coupled transformer to produce the required gain. The obtained gain can be tuned by varying the turn ratio $\gamma _\Gamma$ of the transformer within the narrow range of $1 < \gamma _\Gamma < 2$. Also, the gain factor increases with decrease of the transformer turns ratio, $\gamma _\Gamma$ . Small transformer turn ratio results in more practical topology in some voltage gains. It makes the transformer design easier and reduces construction cost. Also, in the proposed topology, the input and output voltages share the same ground. In order to avoid voltage and current spikes on the switches, a commutation strategy is proposed and safe commutation is achieved without using a snubber circuit. The operating principles and steady-state analyses are presented to verify the operational concept of the proposed topology. Also, experimental results are given to verify the validation of the proposed converter. [ABSTRACT FROM AUTHOR]

This paper proposes a three-phase isolated bidirectional ac/dc converter. The converter achieves buck–boost ac/dc bidirectional conversion, sinusoidal ac current, and high-frequency electrical isolation with single-stage structure. The traditional SVPWM algorithm should be modified to keep the voltage–second balance of the transformer. The circuit derivation, operation principles, and SVPWM algorithm are presented specifically. The solution for shoot-through problem is proposed, which does not need extra dead time. To verify the theoretical analysis, the proposed converter was simulated by MATLAB/SIMULINK and a 3 kW prototype was built in the lab. The simulation and experimental results show the high power factor and the low harmonic distortion characteristics of the circuit. [ABSTRACT FROM AUTHOR]

Five-level active neutral-point clamped (5L-ANPC) converter is an attractive topology for high-power medium-voltage motor drives. This paper presents a capacitor voltage-balancing method for the 5L-ANPC converter, including the voltage balancing of dc-link capacitors and flying capacitors. In order to ensure that the series-connected or high-voltage switches of the 5L-ANPC converter are operated at fundamental frequency and the other switches are operated at a constant switching frequency, phase-shifted pulse width modulation is used to control this converter. The relationship between the average neutral-point current and zero-sequence voltage is investigated, and an optimum zero-sequence voltage is calculated to regulate the neutral-point potential. The voltage across the flying capacitor is also regulated by adjusting the switching duty cycles of two PWM signals, which varies the operation time of redundant switching states in each switching period. Simulation and experimental results are presented to verify the validity of this method. [ABSTRACT FROM AUTHOR]

The modular multilevel converter (MMC) is attractive for medium- and high-power applications because of its high modularity, availability, and power quality. In this paper, the current ripple on the dc link of the three-phase MMC derived from the phase-shifted carrier-based pulse-width modulation scheme is analyzed. A control strategy is proposed for the current ripple elimination. Through the regulation of the phase-shifted angles of the carrier waves in the three phases of the MMC, the current ripple on the dc link of the three-phase MMC can be effectively eliminated. Simulations and experimental studies of the MMC were conducted, and the results confirm the effectiveness of the proposed current ripple elimination control. [ABSTRACT FROM AUTHOR]

In this paper, a generalized switching technique for cascaded H -bridge (CHB) converters is proposed. To take advantage of both low- and high-frequency modulation techniques, a hybrid modulation method is utilized. The proposed technique employs the low-frequency switching for voltage balancing of the dc-link capacitors, and the high-frequency sinusoidal pulse-width modulation switching for shaping the input ac current. Using the proposed technique, the stable operating region of CHB converters is extended. The proposed technique is capable of maintaining the dc voltages balanced even under critical operating conditions in which the load of one H-bridge cell is removed. The validity and effectiveness of the proposed method is confirmed by several simulation and experimental tests on a seven-level CHB rectifier. [ABSTRACT FROM AUTHOR]

In electric vehicle (EV) energy storage systems, a large number of battery cells are usually connected in series to enhance the output voltage for motor driving. The difference in electrochemical characters will cause state-of-charge (SOC) and terminal voltage imbalance between different cells. In this paper, a hybrid cascaded multilevel converter which involves both battery energy management and motor drives is proposed for EV. In the proposed topology, each battery cell can be controlled to be connected into the circuit or to be bypassed by a half-bridge converter. All half-bridges are cascaded to output a staircase shape dc voltage. Then, an H-bridge converter is used to change the direction of the dc bus voltages to make up ac voltages. The outputs of the converter are multilevel voltages with less harmonics and lower dv/dt, which is helpful to improve the performance of the motor drives. By separate control according to the SOC of each cell, the energy utilization ratio of the batteries can be improved. The imbalance of terminal voltage and SOC can also be avoided, fault-tolerant can be easily realized by modular cascaded circuit, so the life of the battery stack will be extended. Simulation and experiments are implemented to verify the performance of the proposed converter. [ABSTRACT FROM AUTHOR]

The modular multilevel converter (MMC) is attractive for medium- or high-power applications because of the advantages of its high modularity, availability, and high power quality. The voltage balancing of the floating capacitors in the cascaded submodules of the MMC is a key issue. In this paper, a voltage-balancing control method is proposed. This method uses the phase-shifted carrier-based pulsewidth modulation scheme to control high-frequency current components for capacitor voltage balancing in the MMC without measuring the arm currents. Simulations and experimental studies of the MMC were conducted, and the results confirm the effectiveness of the proposed capacitor voltage-balancing control method. [ABSTRACT FROM AUTHOR]

The five-level active neutral-point (NP)-clamped (ANPC) converter is a newly emerging topology which can overcome the drawbacks of traditional NP-clamped and flying-capacitor multilevel converters. This paper presents a comprehensive theoretical analysis of the NP potential balancing issue and demonstrates that the NP potential can be naturally balanced under ideal and steady conditions. An NP potential balancing method based on zero-sequence voltage injection is presented. By calculating the average NP currents of all key zero-sequence voltages, the most appropriate zero-sequence voltage is selected to generate the demanded NP current, which can also limit the switching frequency of the series-connected insulated-gate bipolar transistors to the fundamental frequency. A three-phase five-level ANPC inverter prototype is built up, and both steady and dynamic experimental results are presented to verify the validity of this method. [ABSTRACT FROM PUBLISHER]

Improved pulse regulation (IPR) control, a novel control technique for switching dc–dc converters, is proposed and studied in this paper. According to the output voltage and load current of the switching dc–dc converter, IPR control technique achieves output voltage regulation by generating control pulse train made up of some preset control pulses with different duty ratios. IPR control needs only comparators, triggers, and some simple logic devices, without error amplifier and the corresponding compensation circuit of pulse width modulation control scheme, thus IPR control scheme is easy to realize, benefits with excellent transient performance and stability. The principle and operation of IPR control scheme are introduced and illustrated with buck converter operating in discontinuous conduction mode as an example. Simulation and experimental results are presented to show that IPR-controlled converter has much lower output voltage ripple and more accurate output voltage regulation than PR converter. [ABSTRACT FROM PUBLISHER]

This paper presents a flyback switch-mode rectifier (SMR) with spread harmonic spectrum. The SMR switching control is conducted by a charge-regulated pulsewidth modulation (PWM) scheme with constant turn-on period. The inherently stable discontinuous conduction mode operation is preserved to yield good line drawn power quality. In voltage loop, a quantitatively designed PI feedback controller is augmented with a robust error cancellation control scheme. Further improved dc output voltage regulation and input power quality performances are achieved under varied operating conditions. In spread harmonic spectrum control, the harmonic spectral properties of the developed flyback SMR are first analyzed. Then, the dedicated random switching scheme is developed to let its switch current harmonic spectrum be dispersedly distributed. In the proposed random switching scheme, the PWM turn-off period is modulated using 1-b binary sequence, pseudo random binary sequence, and 4-b binary sequences. Under randomized harmonic spectrum, the SMR control performances are not sacrificed. [ABSTRACT FROM PUBLISHER]

Impedance source inverters (ISIs) are gaining attention due to features such as single-stage conversion, buck-boost capability, and inherent shoot-through protection. To maintain the required ac output voltage, typically ISIs are operated at a higher dc-link voltage due to constrained modulation index. This also increases voltage stress across capacitors and switches of the converter. This voltage stress is approximately double compared to that of voltage source inverter with preboost stage (Boost-VSI). To mitigate this problem, a new pulsewidth modulation (PWM) scheme for the active-front-end based ISIs (AFE-ISIs) is proposed. The proposed scheme enables the ISIs to produce high ac gain with lower voltage stress across the capacitor and switches. In other words, the proposed scheme blends the advantages of Boost-VSI into ISIs. With the new PWM scheme, there are also reductions in output voltage total harmonic distortion, switching frequency ripple in the inductor current, and power loss in the converter. A prototype of the current-fed switched inverter, an AFE-ISI, is designed, and the proposed PWM scheme is implemented. Experimental results obtained are in accordance with the proposed theory and show that the voltage stress has reduced from 325 V to 203 V for an ac output of 110 V. [ABSTRACT FROM AUTHOR]

An LED driver consisting of dimmable current balancing circuits (CBCs) and a boost converter with drain voltage balance (DVB) and phase-shifted pulsewidth modulation (PSPWM) control schemes is presented. To reduce the power loss on conventional linear current regulators, CBCs are employed. The DVB control scheme is proposed to maintain a desired constant voltage across the CBCs, so as to increase current balance and achieve high efficiency of the CBCs. Thus, the bus voltage of the boost converter is adaptively regulated based on the DVB control. The PSPWM control scheme can alleviate the variation of the bus current provided by the boost converter. As a result, the transient ripple of the bus voltage can be reduced when the light-emitting diode (LED) strings are turned on and off. Furthermore, the utilization of DVB control is increased when the PWM dimming duty cycle becomes lower. The experimental results demonstrate that the minimum voltage among the CBCs is always kept at the lowest constant level while maintaining the required current passing through the LED strings. The efficiency of the CBCs is kept almost the same for different LED currents and is over 95%. Thus, a high-efficient parallel-string dimmable LED driver with simple circuitry can be achieved. [ABSTRACT FROM PUBLISHER]

A novel dual-mode control scheme is developed here to enable synchronous buck converters (SBC) to operate in a continuous-conduction mode under heavy-load conditions and in a discontinuous-conduction mode under light-load conditions. When an SBC operates in a discontinuous-conduction mode, a quasi-resonant valley switching technique can be employed to turn on a synchronous switch, perform zero-voltage switching at main switches, and improve the light-load efficiency. The proposed scheme does not require the addition of an auxiliary circuit in the SBC, providing it with the advantages of low cost and easily built-in integrated circuits. To verify its feasibility, an SBC equipped with the proposed control scheme is developed, with output voltage and output power of 5 V and 25 W, respectively. [ABSTRACT FROM PUBLISHER]

The interleaved PFC topologies have been widely used since they allow for smaller components, improved thermal performance, better transients, and reduced current ripple. In this letter, conventional two-phase interleaved universal input PFC topology is modified to obtain dual independent outputs for server applications, which minimizes the transient effects of interleaving legs on each other through two split dc buses. A new digital control method using only one current sensor located on the negative dc rail is proposed to control the dual-output interleaved PFC converter. Double-loop digital control of two interleaving stages is implemented using a single low-cost microcontroller (TMS320F28027-PiccoloA). In the proposed control technique, the control circuitry, input voltage, and current sensing circuits are shared between two PFC power stages, which minimize the size and the cost of the design significantly. [ABSTRACT FROM AUTHOR]

This study presents a space vector pulsewidth modulation algorithm for five-phase converters operating in the overmodulation region that forbids the use of zero vectors, covering the whole overmodulation range and providing minimum x\--y voltages. Avoiding zero vectors reduces the content of low-order current harmonics and, at the same time, reduces the common-mode voltage (CMV) by 40%. The method is first implemented using medium and large voltage space vectors, showing good performance in terms of current harmonic content. Then, the algorithm is applied to the case when four large vectors are used, further reducing the peak-to-peak CMV by 80% and still demonstrating a satisfactory performance. Both methods are experimentally compared to existing overmodulation algorithms obtaining better current quality and lower peak-to-peak CMV. [ABSTRACT FROM AUTHOR]

Voltage total harmonic distortion and quadratic voltage ripple criteria are accepted figures of merit of a multilevel pulse width modulation (PWM) converter voltage quality. The dominating frequency domain approach does not deliver simple closed-form expressions and practically requires accounting up to 40–50 switching harmonics. Assuming infinitely high switching frequency, suggested time domain approach to a multilevel multiphase PWM voltage quality evaluation provides closed-form piece-wise analytical solutions. These simple formulas clearly reveal the dependence on modulation index for arbitrary voltage level and odd phase numbers. The results are applicable to any type of multilevel converters (including interleaved, open winding and other) operated with nearest level/nearest space vector modulation and relatively high switching frequency. [ABSTRACT FROM PUBLISHER]