Search

Thin film transistor (TFT) active matrix backplanes are used in large area electronic systems, such as displays and image sensors. With backplanes being fabricated on wearable and flexible substrates, the possibilities of operational faults in backplanes have increased. These faults could either be hard faults, such as line opens or shorts or could be softer faults, such as time dependent variations in the TFT transfer characteristics. Real time diagnosis of these faults require built-in-self-test systems. While many such systems have been demonstrated to diagnose hard faults, an easily realizable system to identify soft faults, such as variations in transistor transconductance remain an open challenge. In this paper, we discuss a system that extracts the transconductance by charging and then discharging the pixel capacitor at various gate voltages for an active matrix liquid crystal display backplane. This permits a plot of the time averaged current versus the gate voltage from which the spatial variation of transconductance can be extracted. The details of the design are discussed and a proof of concept with a $3\times 4$ amorphous silicon backplane is demonstrated.

In this paper, we present the fabrication and characterization of molybdenum microheaters for high-temperature gas sensing applications. The surface morphology of dc magnetron sputtered molybdenum thin films was characterized by scanning electron microscopy and atomic force microscopy. The suspended membrane microheater consumed 104 mW to reach a maximum temperature of 800 degrees C and showed an absolute thermal resistance of 7.2 degrees C/mW. Thermal distribution patterns over the active heating area were recorded using FLIR camera. It showed a temperature gradient of 1.18 % from the center of the microheater to its periphery. The thermal and mechanical stabilities of the microheater were analyzed, and its membrane failure at higher operating temperatures was prevented. The microheater membrane deformation at different temperatures was characterized using optical profilometer, and its maximum value was found to be 16.25 mu m at 800 degrees C. The microheater response to a pulse, continuous pulse train, and constant dc voltages was characterized. Its response and recovery times are in the order of 19 and 34 ms, respectively. It showed a stable temperature with a negligible resistance drift (0.96%) over a period of 600 h. The TiO2 thin film integrated molybdenum microhotplate-based MEMS gas sensor response for CO (5000 ppb) was measured at different operating temperatures (300 degrees C-700 degrees C).

Pulmonary function tests (PFTs) are noninvasive diagnostic tests that evaluate the functionality of the lungs. Spirometry is an established diagnostic tool for the evaluation and management of lung disorders. Pulmonary function testing carried out using a spirometer provides vital information about the functional status of the respiratory system. In this study, a spirometer based on a fiber Bragg grating (FBG) sensor for PFT has been proposed. The proposed fiber Bragg grating spirometer (FBGS) is a novel, noninvasive device that has the ability to convert the rate of air flow into strain variations using an FBG sensor bonded on a cantilever. The FBGS dynamically acquires in real time, the complete breath sequence comprising of inhalation phase, pause phase, and exhalation phase, in terms of the air flow rate along with the time duration of each phase. Fundamental pulmonary parameters such as forced vital capacity (FVC), forced expiratory volume in the first second (FEV1), the FEV1/FVC ratio, and peak expiratory flow are evaluated from the data obtained from the FBGS, which will aid greatly during clinical tests. The results from the FBGS developed are compared with a standard hospital grade pneumotachograph-based spirometer for a sample size of 16 subjects to prove the efficacy of the proposed device.

We discuss the potential application of high dc voltage sensing using thin-film transistors (TFTs) on flexible substrates. High voltage sensing has potential applications for power transmission instrumentation. For this, we consider a gate metal-substrate-semiconductor architecture for TFTs. In this architecture, the flexible substrate not only provides mechanical support but also plays the role of the gate dielectric of the TFT. Hence, the thickness of the substrate needs to be optimized for maximizing transconductance, minimizing mechanical stress, and minimizing gate leakage currents. We discuss this optimization, and develop n-type and p-type organic TFTs using polyvinyldene fluoride as the substrate-gate insulator. Circuits are also realized to achieve level shifting, amplification, and high drain voltage operation.

SU8-based micromechanical structures are widely used as thermal actuators in the development of compliant micromanipulation tools. This paper reports the design, nonlinear thermomechanical analysis, fabrication, and thermal actuation of SU8 actuators. The thermomechanical analysis of the actuator incorporates nonlinear temperature-dependent properties of SU8 polymer to accurately model its thermal response during actuation. The designed SU8 thermal actuators are fabricated using surface micromachining techniques and the electrical interconnects are made to them using flip-chip bonding. The issues due to thermal stress during fabrication are discussed and a novel strategy is proposed to release the thermal stress in the fabricated actuators. Subsequent characterization of the actuator using an optical profilometer reveals excellent thermal response, good repeatability, and low hysteresis. The average deflection is $\sim 8.5~\mu \text{m}$ for an actuation current of $\sim 5$ mA. The experimentally obtained deflection profile and the tip deflection at different currents are both shown to be in good agreement with the predictions of the nonlinear thermomechanical model. This underscores the need to consider nonlinearities when modeling the response of SU8 thermal actuators. [2015-0087]

Power densities required to operate active-matrix organic-light-emitting diode (AMOLED) based displays for high luminance applications, lead to temperature rise due to self heating. Temperature rise leads to significant degradation and consequent reduction in life time. In this work numerical techniques based computational fluid dynamics (CFD) is used to determine the temperature rise and its distribution for an AMOLED based display for a given power density and size. Passive cooling option in form of protruded rectangular fins is implemented to reduce the display temperature.

Direct measurement of three-dimensional (3-D) forces between an atomic force microscope (AFM) probe and the sample benefits diverse applications of AFM, including force spectroscopy, nanometrology, and manipulation. This paper presents the design and evaluation of a measurement system, wherein the deflection of the AFM probe is obtained at two points to enable direct measurement of all the three components of 3-D tip-sample forces in real time. The optimal locations for measurement of deflection on the probe are derived for a conventional AFM probe. Further, a new optimal geometry is proposed for the probe that enables measurement of 3-D forces with identical sensitivity and nearly identical resolution along all three axes. Subsequently, the designed measurement system and the optimized AFM probe are both fabricated and evaluated. The evaluation demonstrates accurate measurement of tip-sample forces with minimal cross-sensitivities. Finally, the real-time measurement system is employed as part of a feedback control system to regulate the normal component of the interaction force, and to perform force-controlled scribing of a groove on the surface of polymethyl methacrylate.

Disease conditions like malaria, sickle cell anemia, diabetes mellitus, cancer, etc., are known to significantly alter the deformability of certain types of cells (red blood cells, white blood cells, circulating tumor cells, etc.). To determine the cellular deformability, techniques like micropipette aspiration, atomic force microscopy, optical tweezers, quantitative phase imaging have been developed. Many of these techniques have an advantage of determining the single cell deformability with ultrahigh precision. However, the suitability of these techniques for the realization of a deformability based diagnostic tool is questionable as they are expensive and extremely slow to operate on a huge population of cells. In this paper, we propose a technique for high-throughput (800 cells/s) determination of cellular deformability on a single cell basis. This technique involves capturing the image(s) of cells in flow that have undergone deformation under the influence of shear gradient generated by the fluid flowing through the microfluidic channels. Deformability indices of these cells can be computed by performing morphological operations on these images. We demonstrate the applicability of this technique for examining the deformability index on healthy, diabetic, and sphered red blood cells. We believe that this technique has a strong role to play in the realization of a potential tool that uses deformability as one of the important criteria in disease diagnosis.

Multifrequency atomic force microscopy is a powerful nanoscale imaging and characterization technique that involves excitation of the atomic force microscope (AFM) probe and measurement of its response at multiple frequencies. This paper reports the design, fabrication, and evaluation of AFM probes with a specified set of torsional eigen-frequencies that facilitate enhancement of sensitivity in multifrequency AFM. A general approach is proposed to design the probes, which includes the design of their generic geometry, adoption of a simple lumped-parameter model, guidelines for determination of the initial dimensions, and an iterative scheme to obtain a probe with the specified eigen-frequencies. The proposed approach is employed to design a harmonic probe wherein the second and the third eigen-frequencies are the corresponding harmonics of the first eigen-frequency. The probe is subsequently fabricated and evaluated. The experimentally evaluated eigen-frequencies and associated mode shapes are shown to closely match the theoretical results. Finally, a simulation study is performed to demonstrate significant improvements in sensitivity to the second- and the third-harmonic spectral components of the tip–sample interaction force with the harmonic probe compared to that of a conventional probe.

Electronic monitoring of perimeters plays vital roles in homeland security, management of traffic and of human-wildlife conflict. This paper reports the design and development of an optical beam-interruption-based ranging and profiling sensor for monitoring perimeters. The developed sensor system can determine the distance of the object from the sensing units and its temporal height profile as the object crosses the system. Together, these quantities can also be used to classify the object and to determine its speed. The sensor is designed, fabricated, and evaluated. The design enables compact construction, high sensitivity, and low measurement crosstalk. The evaluation demonstrates accuracy better than 98.5% in the determination of height and over 94% in determination of the distance of an object from the sensing units. Finally, a strategy is proposed to classify the objects based on the obtained height profiles. The strategy is demonstrated to correctly classify the objects despite differences in their speed and the location at which they cross the system.

This paper presents the design and development of a novel optical vehicle classifier system, which is based on interruption of laser beams, that is suitable for use in places with poor transportation infrastructure. The system can estimate the speed, axle count, wheelbase, tire diameter, and the lane of motion of a vehicle. The design of the system eliminates the need for careful optical alignment, whereas the proposed estimation strategies render the estimates insensitive to angular mounting errors and to unevenness of the road. Strategies to estimate vehicular parameters are described along with the optimization of the geometry of the system to minimize estimation errors due to quantization. The system is subsequently fabricated, and the proposed features of the system are experimentally demonstrated. The relative errors in the estimation of velocity and tire diameter are shown to be within 0.5% and to change by less than 17% for angular mounting errors up to 30 degrees. In the field, the classifier demonstrates accuracy better than 97.5% and 94%, respectively, in the estimation of the wheelbase and lane of motion and can classify vehicles with an average accuracy of over 89.5%.

This paper presents studies on the use of carbon nanotubes dispersed in an insulating fluid to serve as an automaton for healing open-circuit interconnect faults in integrated circuits. The physics behind the repair mechanism is the electric-field-induced diffusion limited aggregation. On the occurrence of an open fault, the repair is automatically triggered due to the presence of an electric field across the gap. We perform studies on the repair time as a function of the electric field and dispersion concentrations with the above application in mind.

Editors' note:Flexible, large-area display and sensor arrays are finding growing applications in multimedia and future smart homes. This article first analyzes and compares current flexible devices, then discusses the implementation, requirements, and testing of flexible sensor arrays.—Jiun-Lang Huang (National Taiwan University) and Kwang-Ting (Tim) Cheng (University of California, Santa Barbara)

This letter studies the impact of electrode segmentation on energy harvesting with piezoelectrics. For cases where the load can be distributed, it is concluded that segmentation of electrodes helps to improve energy content by minimizing surface currents. Using a ribbon of polyvinylidene fluoride under tension as an example, we show that using a six segmented electrode improves energy content by a factor of 2.5. Power delivery remains almost constant except for an anomalous increase when the number of segments is made large. Models are developed to predict improvements in energy content and power delivery.

Purity of the glow-discharge plasma at atmospheric pressure for surface modification applications is always debatable, since it works at ambient atmosphere. We have demonstrated on the use of optical emission spectroscopy to test the purity of this kind of plasma. The effect of gas flow pattern, nature of gas, and its flow rate on the plasma chemistry was studied. The importance of proper system design in maintaining a uniform flow of heavy and inert gases as carrier gas in atmospheric glow-discharge plasma was confirmed. The surface of a plasma-treated PET sample was analyzed using X-ray photoelectron spectroscopy to verify the studies on plasma purity done using emission spectrum.

This letter investigates the influence of a corrugated gate on the transfer characteristics of thin-film transistors. Corrugations that run parallel to the length of the channel from source to drain are patterned on the gate. The author finds that these corrugations result in higher currents as compared to conventional planar-gate transistors.

The out-diffusion of germanium from the core of a photosensitive fiber under elevated temperature is exploited to form a FabryProt filter within a single fiber Bragg grating, by subjecting the diffused region to a single exposure using the standard phase-mask technique. A key aspect of our work is the measurement of the out-diffusion through energy dispersive X-ray analysis. Furthermore, we demonstrate the use of the above single-grating filter for discrimination and simultaneous measurement of strain and temperature. The proposed technique provides a significant advantage over other existing methods that require at least two gratings. � 2006 IEEE.

A novel microcomputer-based electron beam (EB) deposition technique has been developed for preparing thin films with graded composition. A conventional EB gun crucible has been modified to accommodate two constituent materials. Necessary electronic hardware and a software-based INTEL 8085 microcomputer have been built to provide the crucible rotation with the required speed and for changing the emission currents for the EB gun. Mixed oxide films of CeO/sub 2/ and SiO/sub 2/ with composition varying along their thicknesses have been prepared. The composition gradation has been altered by varying the deposition rate and rotational speed of individual constituents. The atomic percentages of Ce, Si, and O have been computed from deposition parameters and correlated with the data obtained from Auger spectroscopy.

Measurement of solar cell AC parameters is important for the design of efficient and reliable satellite power systems. In the present study, the AC parameters of Gallium Arsenide (GaAs/Ge) solar cell have been measured using impedance spectroscopy. The cell capacitance, dynamic resistance, and series resistance were measured. The results show that the transition capacitance (C/sub T/) is dominant up to 0.9 V and beyond 0.9 V diffusion capacitance is significant.