Search

A 20-Gb/s transmitter is implemented in 0.13-/spl mu/m CMOS technology. An on-die 10-GHz LC oscillator phase-locked loop (PLL) creates two sinusoidal 10-GHz complementary clock phases as well as eight 2.5-GHz interleaved feedback divider clock phases. After a 2/sup 20/-1 pseudorandom bit sequence generator (PRBS) creates eight 2.5-Gb/s data streams, the eight 2.5-GHz interleaved clocks 4:1 multiplex the eight 2.5-Gb/s data streams to two 10-Gb/s data streams. 10-GHz analog sample-and-hold circuits retime the two 10-Gb/s data streams to be in phase with the 10-GHz complementary clocks. Two-tap equalization of the 10-Gb/s data streams compensate for bandwidth rolloff of the 10-Gb/s data outputs at the 10-GHz analog latches. A final 20-Gb/s 2:1 output multiplexer, clocked by the complementary 10-GHz clock phases, creates 20-Gb/s data from the two retimed 10-Gb/s data streams. The LC-VCO is integrated with the output multiplexer and analog latches, resonating the load and eliminating the need for clock buffers, reducing power supply induced jitter and static phase mismatch. Power, active die area, and jitter (rms/pk-pk) are 165 mW, 650 /spl mu/m/spl times/350 /spl mu/m, and 2.37 ps/15 ps, respectively.

A 0.622-8-Gb/s clock and data recovery (CDR) circuit using injection locking for jitter suppression and phase interpolation in high-bandwidth system-on-chip solutions is described. A slave injection locked oscillator (SILO) is locked to a tracking aperture-multiplying DLL (TA-MDLL) via a coarse phase selection multiplexer (MUX). For the fine timing vernier, an interpolator DAC controls the injection strength of the MUX output into the SILO. This 1.2-V 0.13-/spl mu/m CMOS CDR consumes 33 mW at 8Gb/s. Die area including voltage regulator is 0.08 mm/sup 2/. Recovered clock jitter is 49 ps pk-pk at a 200-ppm bit-rate offset.

A compact (1 mm /spl times/ 160 /spl mu/m) and low-power (80-mW) 0.18-/spl mu/m CMOS 3.125-Gb/s clock and data recovery circuit is described. The circuit utilizes injection locking to filter out high-frequency reference clock jitter and multiplying delay-locked loop duty-cycle distortions. The injection-locked slave oscillator output can have its output clocks interpolated by current steering the injecting clocks. A second-order clock and data recovery is introduced to perform the interpolation and is capable of tracking frequency offsets while exhibiting low phase wander.

This paper presents analyses and experimental results on the jitter transfer of delay-locked loops (DLLs). Through a z-domain model, we show that in a widely used DLL configuration, jitter peaking always exists and high-frequency jitter does not get attenuated as previous analyses suggest. This is true even in a first-order DLL and an overdamped second-order DLL. The amount of jitter peaking is shown to trade off with the tracking bandwidth and, therefore, the acquisition time. Techniques to reduce jitter amplification by loop filtering and phase filtering are discussed. Measurements from a prototype chip incorporating the discussed techniques confirm the prediction of the analytical model. In environments where the reference clock is noisy or where multiple timing circuits are cascaded, this jitter amplification effect should be carefully evaluated.

A multiplying delay-locked loop (MDLL) for high-speed on-chip clock generation that overcomes the drawbacks of phase-locked loops (PLLs) such as jitter accumulation, high sensitivity to supply, and substrate noise is described. The MDLL design removes such drawbacks while maintaining the advantages of a PLL for multirate frequency multiplication. This design also uses a supply regulator and filter to further reduce on-chip jitter generation. The MDLL, implemented in 0.18-/spl mu/m CMOS technology, occupies a total active area of 0.05 mm/sup 2/ and has a speed range of 200 MHz to 2 GHz with selectable multiplication ratios of M=4, 5, 8, 10. The complete synthesizer, including the output clock buffers, dissipates 12 mW from a 1.8-V supply at 2.0 GHz. This MDLL architecture is used as a clock multiplier integrated on a single chip for a 72/spl times/72 STS-1 grooming switch and has a jitter of 1.73 ps (rms) and 13.1 ps (pk-pk).

We present a 4-Gb/s I/O circuit that fits in 0.1-mm/sup 2/ of die area, dissipates 90 mW of power, and operates over 1 m of 7-mil 0.5-oz PCB trace in a 0.25-/spl mu/m CMOS technology. Swing reduction is used in an input-multiplexed transmitter to provide most of the speed advantage of an output-multiplexed architecture with significantly lower power and area. A delay-locked loop (DLL) using a supply-regulated inverter delay line gives very low jitter at a fraction of the power of a source-coupled delay line-based DLL. Receiver capacitive offset trimming decreases the minimum resolvable swing to 8 mV, greatly reducing the transmission energy without affecting the performance of the receive amplifier. These circuit techniques enable a high level of I/O integration to relieve the pin bandwidth bottleneck of modern VLSI chips.