Search

Driven by climate change and the need for a more sustainable construction sector, policy is increasingly demanding and promoting timber hybrid construction methods. In the German state of Baden-Württemberg, every new public building has to be of timber or timber hybrid construction (Holzbauoffensive BW). The objective of multi-story buildings with large floor spans can only be achieved in a resource-efficient way by hybrid constructions combining timber and steel components. A research project recently completed at the Karlsruhe Institute of Technology was aimed at the development and systematic investigation of hybrid bending beams in which an advantageous combination of the materials steel and timber is used. For this purpose, steel profiles are integrated into timber cross-sections in a shear-resistant manner by adhesive bonding. As part of the experimental, numerical and analytical investigations, different cross-sections of steel and timber, as well as different construction materials, were considered (GL24h, LVL48p, LVL80p, S355 and S420). The results of large-scale four-point bending tests illustrate the potential of this new hybrid construction method. Depending on the geometry and material combinations tested, the bending stiffness could be increased by up to 250%, and the load-carrying capacity by up to 120%, compared to a glulam beam with identical dimensions. [ABSTRACT FROM AUTHOR]

The commercialization of modular timber products as cost-effective and lightweight components has resulted in innovative engineering products, e.g., glued laminated timber, laminated veneer lumber, I-beams, cross-laminated timber and solid timber joined with wedge joints. With the passage of time, timber structures can deteriorate, or new structural elements are required to increase the stiffness or load-bearing capacity in newly built structures, e.g., lintels over large-scale glazing or garages, or to reduce cross-sectional dimensions or save costly timber material while still achieving low weight. It is in such cases that repair or correct reinforcement is required. In this experimental and numerical study, the static performance of flexural timber beams reinforced with prestressed basalt BFRP, glass GFRP and hybrid glass–basalt fiber bars is shown. The experimental tests resulted in an increase in the load-carrying capacity of BFRP (44%), GFRP (33%) and hybrid bars (43%) and an increase in the stiffness of BFRP (28%), GFRP (24%) and hybrid bars (25%). In addition to this, glued laminated timber beams reinforced with prestressed basalt rods subjected to biological degradation, 7 years of weathering and prolonged exposure to various environmental conditions were examined, and an increase in the load-bearing capacity of 27% and an increase in stiffness of 28% were obtained. In addition, full-size laminated timber beams reinforced with prestressed basalt bars were investigated in the field as an exploratory test under fire conditions at elevated temperatures, and the effect of the physical–mechanical properties during the fire was examined via an analysis of these properties after the fire. In addition, a satisfactory correlation of the numerical simulations with the experimental studies was obtained. The differences were between 1.1% and 5.5%. The concordance was due to the fact that, in this study, the Young, Poisson and shear moduli were determined for all quality classes of sawn timber. Only a significant difference resulted in the numerical analysis for the beams exposed to fire under fire conditions. The experimental, theoretical and numerical analyses in this research were exploratory and will be expanded as directions for future research. [ABSTRACT FROM AUTHOR]

In this study, alder, spruce, and beech woods were used for homogeneous symmetric, inhomogeneous symmetric (combined) and inhomogeneous non-symmetric glued laminated timber (glulam) beams glued with resorcinol phenol formaldehyde (RPF) adhesive. The aim of this paper is to determine and compare the modulus of elasticity of glulam beams using three methods, i.e., analytical calculation, numerical model (FEM) and experimental testing. As an additional characteristic, the bending strength (MOR) of the beams was determined during experimental testing. Analytical calculation was used to calculate the modulus of elasticity (MOE) of glued laminated timber based on the knowledge of the modulus of elasticity of solid wood and to estimate the location of the neutral axis during bending. According to calculations, for symmetrical combinations, the deviation from the real neutral axis does not exceed 5%. In the case of the modulus of elasticity, the deviation is an average of 4.1% from that of the actual measured beams. The numerical model includes finite element modelling, where the deflection of the modelled beams can be calculated with a deviation of up to 10%. The last method was experimental testing of glued beams using four-point bending, in which, among homogeneous beams, beech glulam beams achieved the highest MOE and MOR, while alder glulam beams achieved the lowest. The combination of wood species resulted in an increase in both MOE and MOR compared to homogeneous spruce and alder beams. [ABSTRACT FROM AUTHOR]

This paper presents a numerical investigation of the flexural behavior of timber beams externally strengthened with carbon-fiber-reinforced polymer (CFRP) sheets. At first, the accuracy of linear elastic and elastic-plastic models in predicting the behavior of bare timber beams was compared. Then, two modeling approaches (i.e., the perfect bond method and progressive damage technique using the cohesive zone model (CZM)) were considered to simulate the interfacial behavior between FRP and timber. The models were validated against published experimental data, and the most accurate numerical procedure was identified and subsequently used for a parametric study. The length of FRP sheets varied from 50% to 100% of the total length of the beam, while different FRP layers were considered. Moreover, the effects of two strengthening configurations (i.e., FRP attached in the tensile zone only and in both the tensile and compressive zones) on load-deflection response, flexural strength, and flexural rigidity were considered. The results showed that elastic-plastic models are more accurate than linear elastic models in predicting the flexural strength and failure patterns of bare timber beams. In addition, with increasing FRP length, the increase in flexural strength ranged from 10.3% to 52.9%, while no further increase in flexural strength could be achieved beyond an effective length of 80% of the total length of the beam. Attaching the FRP to both the tensile and compressive zone was more effective in enhancing the flexural properties of the timber beam than attaching the FRP to the tensile zone only. [ABSTRACT FROM AUTHOR]

This study delved into the combustion properties of combined glulam bonded using polyurethane (PUR) and resorcinol-phenol-formaldehyde (RPF) adhesives. The experiment involved three distinct wood species, namely, spruce, alder, and beech, which were combined in homogeneous, non-homogeneous symmetrical, and non-homogeneous asymmetrical arrangements. These species were selected to represent a spectrum, namely, softwood (spruce), low-density hardwood (alder), and high-density hardwood (beech). The varying combinations of wood species illustrate potential compositions within structural elements, aiming to optimize mechanical bending resistance. Various parameters were measured during combustion, namely, the heat release rate (HRR), peak heat release rate (pHRR), mass loss rate (MLR), average rate of heat emission (ARHE), peak average rate of heat emission (MARHE), time to ignition (TTI), and effective heat of combustion (EHC). The findings indicate that incorporating beech wood into the composite glulam resulted in an increase in heat release, significantly altering the burning characteristics, which was particularly evident at the second peak. Conversely, the use of spruce wood exhibited the lowest heat release rate. Alder wood, when subjected to heat flux at the glued joint, displayed the highest heat emission, aligning with the results for EHC and MARHE. This observation suggests that wood species prone to early thermal decomposition emit more heat within a shorter duration. The time to ignition (TTI) was consistent, occurring between the first and second minute across all tested wood species and combinations. Notably, when subjected to heat flux, the glulam samples bonded with PUR adhesive experienced complete delamination of the initial two glued joints, whereas those bonded with RPF adhesive exhibited only partial delamination. [ABSTRACT FROM AUTHOR]

These elements are innovative and of interest to many researchers for the reinforcement of wooden elements. For the reinforced beam elements, the effect of the reinforcement factor, FRP and steel elastic modulus or FRP and steel arrangement of the reinforcement on the performance of the flexural elements was determined, followed by reading the load-displacement diagram of the reinforced beam elements. The finite element model was then developed and verified with the experimental results, which was mainly related to the fact that the general theory took into account the typical tensile failure mode, which can be used to predict the flexural strength of reinforced timber beams. From the tests, it was determined that reinforced timber beam elements had relatively ductile flexural strengths up to brittle tension for unreinforced elements. As for the reinforcements of FRP, the highest increase in load-bearing capacity was for carbon mats at 52.47%, with a reinforcement grade of 0.43%, while the lowest was for glass mats at 16.62% with a reinforcement grade of 0.22%. Basalt bars achieved the highest stiffness, followed by glass mats. Taking into account all the reinforcements used, the highest stiffness was demonstrated by the tests of the effectiveness of the reinforcement using 3 mm thick steel plates. For this configuration with a reinforcement percentage of 10%, this increase in load capacity was 79.48% and stiffness was 31.08%. The difference between the experimental and numerical results was within 3.62–27.36%, respectively. [ABSTRACT FROM AUTHOR]

Laboratory research of wood–CFRP (carbon fiber reinforced polymer) structural elements, especially beams, is a scientific issue undertaken by many scientists. Research is often complemented with numerical analysis with the use of complex finite element method (FEM) models. Modern FEM software offers models that can reproduce such properties and phenomena as orthotropy and plasticity of wood and CFRP, delamination and mechanical behavior of adhesive layers, and damage of a strengthened element. The author of the paper reproduces numerical laboratory research of a four-point bending test of a glulam beam strengthened with CFRP tape. The main goal of the numerical research is an analysis of how the complexity of the FEM model influences the results of calculations, especially stress, deflection, and bearing capacity of the glulam beam. In some cases, a simpler model can be satisfactory, especially for a structural engineer, who takes into account serviceability limit states (permissible deflection of a structural member) and assumes that stress should not exceed the yield stress of timber. [ABSTRACT FROM AUTHOR]

Damage often develops in glued laminated timber members under high bending loads due to natural defects in the timber, which results in their low load-bearing capacity and stiffness. In order to improve the bending mechanical properties of glulam beams, a new type of longitudinal glulam reinforcement with pre-stressed basalt fibre-reinforced polymer composites (BFRP) was developed using the Near Surface Mounted (NSM) technique. The strengthening method consisted of two pre-stressed BFRP bars glued into the grooves at the bottom side of the beam; meanwhile, for the second strengthening alternative, the third BFRP bar was embedded into the groove at the top side of the beam. Therefore, an experimental study was carried out to verify this strengthening technique, in which fifteen full-size timber beams were tested with and without bonded BFRP bar reinforcement in three series. According to the results of this experimental study, it can be seen that the effective load-bearing capacity of the reinforced beams increased up to 36% and that the stiffness of the beams increased by 23% compared to the unreinforced beams. The tensile stresses in the wooden fibres were reduced by 11.32% and 25.42% on average for the beams reinforced with two and three BFRP bars, respectively. On the other hand, the compressive stresses were reduced by 16.53% and 32.10% compared to the unreinforced beams. The usual failure mode saw the cracking of the wood fibres at the defects, while for some specimens, there were also signs of cracks in the epoxy adhesive bond; however, the crack propagation was, overall, significantly reduced. The numerical calculations also show a good correlation with the experimental results. The difference in the results between the experimental and numerical analysis of the reinforced and unreinforced full-sized beams ranged between 3.63% and 11.45%. [ABSTRACT FROM AUTHOR]

To increase the sustainability of prefabricated timber buildings and constructions, composite timber beams with "box" cross-sections were developed in collaboration with an industry partner. They were constructed from a solid timber frame and from webs made of residual waste wood-particle boards from prefabricated timber buildings production. The developed beams' design concepts presented in this paper were governed by architectural features of prefabricated timber buildings, geometrical limitations, available production technology, and structural demand related to various possible applications. The paper presents the results of experimental bending tests of six variations of the developed composite timber beams constructed by mechanical fasteners only. The developed design concept of composite timber beams without adhesives is beneficial compared to glued beams in terms of design for deconstruction and lower VOC emissions. The tests were conducted to study the influence of the following parameters on the beams' mechanical behavior: (i) web material (oriented strand boards (OSBs) vs. cement-particle boards); (ii) the influence of beam timber frame design (flanges and web stiffeners vs. flanges, web stiffeners, and compressive diagonals), and (iii) the influence of stiffener–flange joint design. Besides the beams' load-bearing capacities, their linear and non-linear stiffness characteristics were the main research interest. While adding compressive timber diagonals did not prove to significantly increase the stiffness of the beams in the case of cement-particle board webs, it increased their load-bearing capacity by enabling the failure of flanges instead of prior webs and stiffener–flange joints failure. For beams with OSB webs, failure of the bottom flange was achieved already with the "basic" timber frame design, but timber diagonals proved beneficial to increase the stiffness characteristics. Finally, mechanical characteristics of the developed beams needed in structural design for their application are provided together with further development guidelines. [ABSTRACT FROM AUTHOR]

The aim of this study was to assess the potential of hardwoods harvested in Croatian forests for the production of glued laminated timber (glulam), mainly of those species for which there is no published performance assessment. Nine sets of glulam beams were produced: three sets using lamellas from European hornbeam, three sets from Turkey oak, and three sets from maple. Each set was characterized by a different hardwood species and surface preparation method. The surface preparation methods included planing, planing followed by sanding with fine grit, and planing followed by sanding with coarse grit. The experimental investigations included shear tests of the glue lines in dry conditions and bending tests of the glulam beams. The shear tests showed satisfactory performance of the glue lines for the Turkey oak and European hornbeam, but not for the maple. The results of the bending tests showed superior bending strength of the European hornbeam compared to the Turkey oak and maple. Planing followed by rough sanding of the lamellas was shown to have a significant influence on the bending strength and stiffness of the glulam from Turkey oak. [ABSTRACT FROM AUTHOR]

Changes in the condition of existing timber structures can be caused by fatigue or biological attack, among other things. Replacing damaged timber is still very expensive, so it seems more advisable to repair or reinforce damaged elements. Therefore, in order to improve the static performance analysis of timber structures, reinforcement applications in timber elements are necessary. In this experimental study, technical-scale glulam beams measuring 82 × 162 × 3650 mm, which were reinforced with carbon strands and carbon laminates, were tested in flexure. A four-point bending test was used to determine the effectiveness of the reinforcement used in the timber beams. Internal strengthening (namely, glued carbon cords placed into cut grooves in the last and penultimate lamella) and an external surface of near-surface mounted (NSM) carbon laminates glued to the bottom surface of the beam were used to reinforce the laminated ashlar beams. As a result of this study, it was found that the bending-based mechanical properties of ash wood beams reinforced with carbon fibre-reinforced polymer composites were better than those of the reference beams. In this work, the beams were analysed in terms of the reinforcement variables used and the results were compared with those for the beams tested without reinforcement. This work proves the good behaviour of carbon fibre reinforced plastic (CFRP—Carbon fibre reinforced polymer) cords when applied to timber beams and carbon laminates. This study illustrated the different reinforcement mechanisms and showed their structural properties. Compared to the reference samples, it was found that reinforcement with carbon strings or carbon laminates increased the load-bearing capacity, flexural strength and modulus of elasticity, and reduced the amount of displacement of the timber materials, which is an excellent alternative to the use of ashlar and, above all, inferior grade materials due to the current shortage of choice grade. Experimental results showed that, with the use of carbon fibre (carbon cords SikaWrap® FX-50 C—Sika Poland Sp. z o.o., Warsaw), the load bearing capacity increased by 35.58%, or with carbon cords SikaWrap® FX-50 C and carbon laminates S&P C-Laminate type HM 50/1.4 - S&P Poland Sp. z o.o., Malbork, by 45.42%, compared to the unreinforced beams. [ABSTRACT FROM AUTHOR]

This study aimed to evaluate the mechanical properties determined in a 4-point bending test of beams made of lumber from which knots had been locally removed and the resulting loss replaced with sound wood. Three sets of beams were prepared, which differed in the number of layers/lamellas and the position of the lamellas from which edge knots were removed. All the lamellas used in the tests were subjected to a modulus of elasticity assessment. In addition to the distribution of defects, it determined the position of a given piece in the beam structure. The tests showed that high mechanical properties could characterise the beams produced in this way, i.e., a modulus of elasticity close to 12 kN/mm2 and a strength above 40 N/mm2, if the lamellas without knots were located below the outer tension lamella. Significantly better results were obtained when PUR glue was used in the inserts rather than MUF. In this case, beams with an improved outer lamella in the tension zone using semi-circular inserts glued with PUR glue had an average strength of 34.6 N/mm2. [ABSTRACT FROM AUTHOR]

The paper deals with the analysis of the load-carrying capacity of a timber semi-rigid connection created from a system of two stands and a rung. The connection was made from glued laminated timber with metal mechanical dowel-type fasteners. Not only a common combination of bolts and dowels, but also fully threaded screws were used for the connection. The aim of the research and its motivation was to replace these commonly used fasteners with more modern ones, to shorten and simplify the assembly time, and to improve the load-carrying capacity of this type of connection. Each of these two types of connections was loaded statically, with a slow increase in force until failure. The paper presents results of the experimental testing. Three specimens were made and tested for each type of the connection. Experimental results were subsequently compared with numerical models. The achieved results were also compared with the assumption according to the currently valid standard. The results indicate that a connection using fully threaded screws provides a better load-carrying capacity. [ABSTRACT FROM AUTHOR]

This study aimed to enhance tropical fast-growing tree species' resistance to subterranean termite (Coptotermes curvignathus) attacks through the manufacturing of polystyrene glued-laminated timber (glulam). Three young tropical wood species, namely manii (Maesopsis eminii), mangium (Acacia mangium), and rubber-wood (Hevea brasiliensis), were cut into laminae. After drying, the laminae were impregnated with styrene monomer, then polymerized using potassium peroxydisulfate as a catalyst and heat. The polystyrene-impregnated laminae were constructed using isocyanate glue and a cold press for three-layered glulam. Untreated or control glulam and solid wood specimens were also prepared. The specimens of each wood species and wood products (solid wood, control glulam, and polystyrene glulam) were exposed to the termite in a laboratory test according to Indonesian standards. The results showed that mangium wood had better resistance to the termite attack than manii and rubber-wood, with both of those woods performing the same. Among the wood products, the glulams were equal and had higher resistance to the termite attack than solid wood. To enhance the termite resistance of polystyrene glulam, we suggest that the polymer loading of polystyrene on each lamina should be increased. In our evaluation of the products' order of priority, polystyrene glulam emerged as performing best towards subterranean termites attack. [ABSTRACT FROM AUTHOR]

The aim of this study was to determine the mechanical properties of laminated beams containing selected wood species in the tension zone using a four-point bending test. Three beam types were manufactured with respect to the timber used in the tension zone, i.e., beams containing oak or beech timber of I and II quality class and pine timber with no defects (as defects had been removed). The manufactured beams were assessed with respect to bending strength and the modulus of elasticity. The obtained results were compared with the performance of BSH (Industrial beams GL made in Germany—Brettschichtholz) industrial beams. We concluded that beams made from pine timber are an appropriate alternative to spruce beams. The static bending strength of the beams made with hardwood faces was 70% higher than that of beams made with pine wood. All types of beams manufactured in the laboratory met the requirements of at least the GL24c class. [ABSTRACT FROM AUTHOR]

Timber is one of the fundamental materials of human civilization, it is very useful and ecologically acceptable in its natural environment, and it fits very well with modern trends in green construction. The paper presents innovative hollow glued laminated (GL) timber elements intended for log-house construction. Due to the lack of data on the behavior of the hollow timber section in compression perpendicular to the grain, the paper presented involves testing the compression strength of elliptical hollow cross-section glue-laminated timber specimens made of softwood and hardwood, as well as full cross-section glue-laminated softwood timber specimens. The experimental research was carried out on a total of 120 specimens. With the maximal reduction of 26% compared to the full cross-section, regardless of the type of wood and direction of load, the compression strength perpendicular to the grain of hollow specimens decreases by about 55% compared to the full cross-section, with the coefficient kc,90 equal to 1.0. For load actions at the edge and the middle of the element, kc,90 factors were obtained with a value closer to those obtained for full cross-section, which indicates the same phenomenology, regardless of cross-sectional weakening. At the same time, the factors in the stronger axis are lower by about 10%, and in the weaker axis by about 30% compared to those prescribed by the Eurocode. Experimental research was confirmed by FEM analysis. Comparative finite element analysis was performed in order to provide recommendations for future research and, consequently, to determine the optimal cross-section form of the hollow GL timber element. By removing the holes in the central part of the cross-section, the stress is reduced. The distance of the holes from the edges defines the local cracking. Finally, if the holes are present only in the central part of the element, the behavior of the element is more favorable. [ABSTRACT FROM AUTHOR]

Fire safety greatly contributes to feeling safe, and it is a key parameter for the selection of building materials. The combustibility of timber is one of the main reasons to have the strict restriction on timber for use as a building material, especially for multistory buildings. Therefore, the main prerequisite for the use of timber in buildings is to ensure adequate fire resistance, using passive and active fire protection measures. This article contains the results of mechanical and fire experimental tests of both normal and innovative hollow glued laminated timber beams. A total of 10 timber beams were tested at ambient temperature, and 3 timber beams in fire conditions, which differed in cross-section type but also in the applied fire protection. The first beam was a normal GL beam without fire protection, the second a hollow beam covered by intumescent paint, while the third was also hollow, additionally protected by mineral wool infill inside the holes. The load-carrying capacity of the hollow beam in ambient conditions was estimated at 65% of the load-carrying capacity of a normal GL beam. Fire tests indicated that hollow timber beams with both intumescent paint and mineral wool infill failed at a similar time as a normal GL beam without fire protection. One-dimensional β0 and notional charring rates βn were obtained. Time to the protective material failure was 17 min. The main cause of failure of hollow beams was the appearance of delamination due to the reduction of the lamella bonding surface. [ABSTRACT FROM AUTHOR]

The paper deals with the analysis of the rotational stiffness of a semirigid connection created from a system of two stands and a rung. The connection was made from glued laminated timber with metal mechanical dowel-type fasteners. Not only a common combination of bolts and dowels but also fully threaded screws were used for the connection. The aim of the research and its motivation was to replace commonly used fasteners with more modern ones, to shorten and simplify the assembly time, and to improve the load-carrying capacity of this type of connection. Each of these two types of connection was loaded to the level of 60%, 80%, and 100% of the ultimate limit state value. Subsequently, the rotational stiffness was determined for each load level after five loading and unloading cycles. This paper presents the results and comparison of the experimental testing and the numerical modeling. The obtained results were also compared with the assumption according to the currently valid standard. [ABSTRACT FROM AUTHOR]

Glulam beams are increasingly used in the construction industry because of their high strength and the possibility of using round timber with smaller cross-sections. The load-bearing capacity of beams is strongly related to the quality of the outer layers and, in the case of wood, especially the tension zones. For these reasons, this study decided to replace the outer lamella with tensile plywood. The produced beams were subjected to static bending strength and modulus of elasticity evaluation. It was shown that the best static bending strength values were obtained for beams containing plywood in the tension layer. However, the change in structure in the tension zone of beams made of glued laminated timber results not only in an increase in the load capacity of elements produced in this way but also in a decrease in the range/range of the obtained results of bending strength. This way of modifying the construction of glued laminated beams allows a more rational use of available pine timber. [ABSTRACT FROM AUTHOR]

Engineered wood products (EWP) such as glulam beams are gaining more and more popularity due to several advantages resulting from the wood itself, as well as the constant search for structural materials of natural origin. However, building materials face some requirements regarding their strength. Thus, the study aimed to assess the static bending strength of structural beams produced with the use of pine wood, after the periodic loading of approximately 80 kN for a year. The manufactured beams differed in the type of facing layers, i.e., pine timber with a high modulus of elasticity and plywood. The produced beams, regardless of their structure, are characterized by a similar static bending strength. Moreover, it has been shown that the loading of beams in the range of about 45% of their immediate capacity does not significantly affect their static bending strength and linear modulus of elasticity. [ABSTRACT FROM AUTHOR]

This study investigates the optimization of the design of timber floor joists, taking into account the self-manufacturing costs and the discrete sizes of the structure. This non-linear and discrete class of optimization problem was solved with the multi-parametric mixed-integer non-linear programming (MINLP). An MINLP optimization model was developed. In the model, an accurate objective function of the material and labor costs of the structure was subjected to design, strength, vibration and deflection (in)equality constraints, defined according to Eurocode regulations. The optimal design of timber floor joists was investigated for different floor systems, different materials (sawn wood and glulam), different load sharing systems, different vertical imposed loads, different spans, and different alternatives of discrete cross-sections. For the above parameters, 380 individual MINLP optimizations were performed. Based on the results obtained, a recommended optimal design for timber floor joists was developed. Engineers can select from the recommendations the optimal design system for a given imposed load and span of the structure. Economically suitable spans for timber floor joists structures were found. The current knowledge of competitive spans for timber floor joists is extended based on cost optimization and Eurocode standards. [ABSTRACT FROM AUTHOR]

Engineered wood products, such as glulam beams, attract much attention from the building industry in recent years. Therefore, there is a constant necessity to seek new models of structural beams, which assume the use of outsized sawn wood pieces as an alternative for the standard construction timber. Three variants of glulam beams, composed of the main yield and side boards arranged in various structures, were proposed. Moreover, the usefulness of wedge-jointed, small-sized timber pieces was also investigated. The manufactured beams were tested, in terms of their mechanical properties, such as bending strength, elastic energy, modulus of elasticity, and resilience. The outcomes have shown that the beams manufactured using wedge-bonded timber of lower grade do not deviate considerably from beams produced from homogeneous lamellas. Furthermore, the results of modulus of elasticity, in the case of the three-layered beams composed of both small-sized non-homogenous main yield and side boards, exceeded the requirements from EN 14080. It allowed us to classify the obtained materials as GL 32c, which is the highest grade specified within the standard. [ABSTRACT FROM AUTHOR]

Numerous studies have shown that the geometry of micro-joints significantly affects the strength of the so joined timber element. The bending strength increases by creating a larger bonding area by increasing the length of the wedge joint. Although this type of joint has been successfully used for many years, it can still be troublesome to make. For these reasons, the present study investigated an easy-to-fabricate wedge joint, which we folded during the beams' formation and glued with the same adhesive as the individual lamellas. Although the research has not fully answered all the questions relevant to both scientific and technological curiosity, it indicates the great potential of this solution. Following the principle adopted in the ongoing wood optimisation work, we concluded that the beams of the target cross-section should be produced, and it should only be possible to cut them to a certain length. In this approach, we only removed defects at critical points for the beam structure and, in this way, up to 30% of the timber processed could be saved or better utilised. [ABSTRACT FROM AUTHOR]

This paper presents the formulae and finite element analysis models for predicting the Modulus of Elastic (MOE) and Modulus of Rupture (MOR) of Cathay poplar finger-jointed glulam. The formula of the MOE predicts the MOE of Cathay poplar glulam glued with one-component polyurethane precisely. Three formulae are used to predict the MOR, and Equation (12) predicts the MOR of Cathay poplar glulam precisely. The finite element analysis simulation results of both the MOE and MOR are similar to the experimental results. The predicted results of the finite element analysis are shown to be more accurate than those of the formulae, because the finite element analysis considers the glue layers, but the formulae do not. Three types of typical failure modes due to bending were summarized. The bending properties of Cathay poplar glulam were compared to those of Douglas fir glulam. The results show that Cathay poplar glulam has a lower stiffness, but a marginally higher strength. One-component polyurethane adhesive is shown to be more effective than resorcinol formaldehyde resin adhesive for Cathay poplar glulam. This study shows that Cathay poplar has the potential to be a glulam material in China. [ABSTRACT FROM AUTHOR]

In this paper, dynamic analyses of two untypical, modern footbridges made of glued-laminated timber are presented. One of them is among the longest cable-stayed bridges for pedestrians in the world, made of such a structural material. Both structures are qualified as having low sensitivity to vibrations. The results of numerical modal analysis using FEM and non-destructive experimental dynamic tests of investigated footbridges are compared. Important differences in obtained results are captured, which are identified as the positive effect in relation to design aspects. Moreover, the same in situ measurements confirm the high level of damping in footbridges made of glued-laminated wood, which is a very significant and distinguishing feature not commonly recognized. The study also calls attention to the choice of timber as an advisable material for footbridges. This is not only because of environmentally friendly and aesthetic reasons, but also due to providing highly satisfying vibration comfort for pedestrians. [ABSTRACT FROM AUTHOR]

With the development of wooden structures and buildings, there is a need to research physical and numerical tests of wood-based structures. The presented research is focused on construction and computational approaches for new types of joints to use in wooden structures, particularly glued lamella elements made of wood and wood-based composites. This article focuses on improving the frame connection of a wooden post and a beam with the use of fasteners to ensure better load-bearing capacity and stiffness of the structure. In common practice, bolts or a combination of bolts and pins are used for this type of connection. The aim is to replace these commonly used fasteners with modern ones, namely full thread screws. The aim is also to shorten and simplify the assembly time in order to improve the load-bearing capacity and rigidity of this type of frame connection. Two variations of the experimental test were tested in this research. The first contained bolts and pins as connecting means and the second contained the connecting means of a full threaded screw. Each experiment contained a total of two tests. For a detailed study of the problem, we used a 2D or 3D computational model that models individual components, including fasteners. [ABSTRACT FROM AUTHOR]

Composite materials are increasingly used to strengthen existing structures or new load-bearing elements, also made of timber. In this paper, the effect of the number of layers of Carbon Fiber Reinforced Polymer (CFRP) on the load-bearing capacity and stiffness of Glued Laminated Timber beams was determined. Experimental research was performed on 32 elements—a series of eight unreinforced beams, and three series of eight reinforced beams: with one, three and five layers of laminate each. The beams with a cross-section of 38 mm × 80 mm and a length of 750 mm were subjected to the four-point bending test according to standard procedure. For each series, destructive force, deflection, mode of failure, and equivalent stiffness were determined. In addition, for the selected samples, X-ray computed tomography was performed before and after their destruction to define the quality of the interface between wood and composite. The results of the conducted tests and analyses showed that there was no clear relationship between the number of reinforcement layers and the load-bearing capacity of the beams and their stiffness. Unreinforced beams failed due to tension, while reinforced CFRP beams failed due to shear. Despite this, a higher energy of failure of composite-reinforced elements was demonstrated in relation to the reference beams. [ABSTRACT FROM AUTHOR]