Search

Lotus-type porous copper was fabricated using a continuous casting method in pressurized hydrogen and nitrogen gas atmospheres. This study evaluates the effects of process parameters, such as the hydrogen ratio, total pressure, and transference velocity, on the resulting pore structure. A continuous casting process was developed to facilitate the mass production of lotus-type porous copper. To achieve the desired porosity and pore diameter for large-scale manufacturing, a systematic evaluation of the influence of each process parameter was conducted. Lotus-type porous copper was produced within a hydrogen ratio range of 25–50%, a transference velocity range of 30–90 mm∙min−1, and a total pressure range of 0.2–0.4 MPa. As a result, the porosity ranged from 36% to 55% and the pore size varied from 300 to 1500 µm, demonstrating a wide range of porosities and pore sizes. Through process optimization, it is possible to control the porosity and pore size. The hydrogen ratio and total pressure were found to primarily affect porosity, whereas the hydrogen ratio, transference velocity, and total pressure significantly influenced pore diameter. When considering these parameters together, porosity was most influenced by the hydrogen ratio, whereas the total pressure and transference velocity had a greater influence on pore diameter. Reducing the hydrogen ratio and increasing the transference velocity and total pressure reduced the pore diameter and porosity. This optimization of the continuous casting process enables the control of porosity and pore diameter, facilitating the production of lotus-type porous copper with the desired pore structures. [ABSTRACT FROM AUTHOR]

Based on a physical water model with a scaling factor of 0.5 and a coupled flow–heat transfer–solidification numerical model, this study investigates the influence of the submerged entry nozzle (SEN) depth on the mold surface behavior, slag entrapment, internal flow field, temperature distribution, and initial solidification behavior in slab casting. The results indicate that when the SEN depth is too shallow (80 mm), the slag layer on the narrow face is thin, leading to slag entrapment. Within a certain range of SEN depths (less than 170 mm), increasing the SEN depth reduces the impact on the mold walls, shortening the "plateau period" of stagnated growth on the narrow face shell. This allows the upper recirculation flow to develop more fully, resulting in an increase in the surface flow velocity and an expansion in the high-temperature region near the meniscus, which promotes uniform slag melting but also heightens the risk of slag entrainment due to shear stress at the liquid surface (with 110 mm being the most stable condition). As the SEN depth continues to increase, the surface flow velocity gradually decreases, and the maximum fluctuation in the liquid surface diminishes, while the full development of the upper recirculation zone leads to a higher and more uniform meniscus temperature. This suggests that in practical production, it is advisable to avoid this critical SEN depth. Instead, the immersion depth should be controlled at a slightly shallower position (around 110 mm) or a deeper position (around 190 mm). [ABSTRACT FROM AUTHOR]

As the metal additive manufacturing (AM) field evolves with an increasing demand for highly complex and customizable products, there is a critical need to close the gap in productivity between metal AM and traditional manufacturing (TM) processes such as continuous casting, machining, etc., designed for mass production. This paper presents the development of the scalable and expeditious additive manufacturing (SEAM) process, which hybridizes binder jet printing and stereolithography principles, and capitalizes on their advantages to improve productivity. The proposed SEAM process was applied to stainless steel 420 (SS420) and the processing conditions (green part printing, debinding, and sintering) were optimized. Finally, an SS420 turbine fabricated using these conditions successfully reached a relative density of 99.7%. The SEAM process is not only suitable for a high-volume production environment but is also capable of fabricating components with excellent accuracy and resolution. Once fully developed, the process is well-suited to bridge the productivity gap between metal AM and TM processes, making it an attractive candidate for further development and future commercialization as a feasible solution to high-volume production AM. [ABSTRACT FROM AUTHOR]

Continuous casting is the most common method for producing steel into semi-finished shapes like billets or slabs. Throughout this process, steel experiences mechanical and thermal stresses, which influence its mechanical properties. During continuous casting, decreased formability in steel components leads to crack formation and failure. One reason for this phenomenon is the appearance of the soft ferrite phase during cooling. However, it is unclear under which conditions this ferrite is detrimental to the formability. In the present research, we investigated what microstructural changes decrease the formability of microalloyed steels during continuous casting. We studied the hot compression behaviour of microalloyed steel over temperatures ranging from 650 °C to 1100 °C and strain rates of 0.1 s − 1 to 0.001 s − 1 using a Gleeble 3800® (Dynamic Systems Inc, Poestenkill, NY, USA) device. We examined microstructural changes at various deformation conditions using microscopy. Furthermore, we implemented a physically-based model to describe the deformation of austenite and ferrite. The model describes the work hardening and dynamic restoration mechanisms, i.e., discontinuous dynamic recrystallisation in austenite and dynamic recovery in ferrite and austenite. The model considers the stress, strain, and strain rate distribution between phases by describing the dynamic phase transformation during the deformation in iso-work conditions. Increasing the strain rate below the transformation temperature improves hot ductility by reducing dynamic recovery and strain concentration in ferrite. Due to limited grain boundary sliding, the hot ductility improves at lower temperatures (<750 °C). In the single-phase domain, dynamic recrystallisation improves the hot ductility provided that fracture occurs at strains in which dynamic recrystallisation advances. However, at very low strain rates, the ductility decreases due to prolonged time for grain boundary sliding and crack propagation. [ABSTRACT FROM AUTHOR]

This article presents a computational study of the influencing parameters on the solidification of the thermoplastic beryllium oxide slurry in an annular forming cavity. The main purpose of this paper is to study the effect of cooling and casting conditions on the solidification of the BeO suspension by considering the temperature-dependent rheological and physical properties. The results of calculations of the Bingham–Papanastasiou rheological model with experimental data in the intervals of phase transitions with different casting rates of beryllium ceramics have been validated. The use of the regularization parameter made it possible to approximate the flow of the slurry at all levels of its shear rates as highly viscous, followed by a continuous transition to a solid state. The speed of heat removal from the molding during the solidification period is determined by the speed of movement of the slurry and the temperature field on which the width of the transition region depends. The process of solidification of the slurry mass has been evaluated by changing its heat flow distribution and density along the length of the concentric channel. The obtained model calculation results make it possible to control the casting process and eventually realize a uniform structure of castings. [ABSTRACT FROM AUTHOR]

Standard AA5083 (ZSE000), AA5083 modified with 0.3 wt.% Zr and 0.3wt.% Sc (ZSE330) and AA5083 modified with 0.3 wt.% Zr, 0.2wt.% Sc and 0.1wt.%Er(ZSE321) sheets were fabricated through a short process (including a simulated twin-belt continuous casting, subsequent direct rolling, intermediate annealing, cold rolling and stress-relief annealing) to systematically investigate the influence of partially substituting Er for Sc on the microstructure, mechanical properties and corrosion resistance of short-processed Al-4.7Mg-0.6Mn-0.3Zr-0.3Sc sheets. The results show that ZSE321 presents the optimal tensile properties (UTS: 541 MPa; 0.2%PS: 469 MPa and EF:7.7%) among the three experimental sheets. This is attributed to significant grain refinement, the inhibition of the recrystallization and promotion on the precipitation of Al3(Sc, Zr, Er) nanoparticles. Furthermore, the corrosion properties of the experimental sheets were also explored in this study, and the short-processed ZSE321 sheet presents the optimum corrosion resistance. [ABSTRACT FROM AUTHOR]

The solidification structure characteristics are decisive for the production of extra-thick slabs. This study developed a solidification heat transfer model and a cellular automaton–finite element coupled model to investigate the solidification behavior and structure characteristics of a 475 mm extra-thick slab. The models were applied under various continuous casting process parameters and different alloy element content. The simulation results reveal that casting speed has the most significant effect on the solidification behavior of extra-thick slabs, surpassing the impact of specific water flow and superheat. The solidification structure characteristics of the 475 mm extra-thick slabs were investigated under various conditions. The findings indicate that at higher casting speeds and superheats, the average grain size increases and the grain number decreases. The average grain size initially decreases and then increases with the rise in specific water flow, reaching its minimum at approximately 0.17 L·kg−1. Additionally, the average grain radius first decreases and then slightly increases with an increase in carbon content, achieving the minimum value of about 0.17% carbon. Compared with carbon and manganese, silicon has a greater impact on the solidification structure of ultra-thick slabs, and a moderate increase in silicon content can effectively refine the grain size. This study provides a theoretical foundation for understanding the changes in solidification structure characteristics and optimizing continuous casting process parameters for 475 mm extra-thick slabs. [ABSTRACT FROM AUTHOR]

During continuous casting, coated slag is applied to molten steel to enhance heat transfer and lubrication. In this study, a numerical calculation model was built to reveal the flowing characteristic of slag according to the fundamental principles of heat transfer and viscous fluid mechanics. The flow and heat transfer behaviour of protective slag on the surface of molten steel and the flow velocity of liquid slag in slag channel gaps were calculated and analyzed. The streaming and thermal conduction situation of slag on the surface of molten steel, as well as the flow velocity of liquid flux in the slag passage gap, were calculated and analyzed. The results showed that as the thickness of the liquidus slag film increased from 10 to 12 mm, the thermal flux density at the top of the flux film layer decreased from 0.1059 to 0.0882 MW/m2. The heat flux density increased rapidly within 0.1 m of the narrow side of the mould, reaching a peak value of 2.27 MW/m2. As the viscosity temperature factor of the flux increased from 0.45 to 2.05, the maximum floating speed of the liquid film from the water inlet to the narrow side in the centre district of the mould decreased from 0.0316 to 0.028 m/s, representing a reduction of approximately 11.4%. This study can provide a reference for the design and improvement of protective slag. [ABSTRACT FROM AUTHOR]

Longitudinal crack defects are a frequent occurrence on the surface of thin slabs during the high-speed continuous casting process. Therefore, this study undertakes a detailed analysis of the solidification characteristics of hyper-peritectic steel thin slabs. By establishing a three-dimensional heat transfer numerical model of the thin slab, the formation mechanism of longitudinal cracks caused by uneven growth of the initial shell is determined. Based on the mechanism of longitudinal crack formation, by adjusting the performance parameters of the mold flux, the contradiction between the heat transfer control and lubrication improvement of the mold flux is fully coordinated, further reducing the incidence of longitudinal cracks on the surface of the casting thin slab. The results show that, using the optimized mold flux, the basicity increases from 1.60 to 1.68, the F- mass fraction increases from 10.67% to 11.22%, the Na2O mass fraction increases from 4.35% to 5.28%, the Li2O mass fraction increases from 0.68% to 0.75%, and the carbon mass fraction reduces from 10.86% to 10.47%. The crystallization performance and rheological properties of the mold flux significantly improve, reducing the heat transfer performance while ensuring the lubrication ability of the molten slag. After optimizing the mold flux, a surface detection system was used to statistically analyze the longitudinal cracks on the surface of the casting thin slab. The proportion of longitudinal cracks (crack length/steel coil length, where each coil produced is about 32 m long) on the surface of the thin slab decreases from 0.056% to 0.031%, and the surface quality of the thin slab significantly improves. [ABSTRACT FROM AUTHOR]

The effect of Al or Cu content on the microstructure and mechanical properties of continuous casting and extrusion Zn alloys has been studied by a room temperature tensile test, X-ray diffraction, and scanning electron microscope. With the increase in Al content, the microstructure of continuous casting and extrusion Zn alloys slightly coarsens, and the lamellar eutectic structure increases. The changes in the above structural factors result in a slight decrease in strength and a significant increase in the elongation of Zn-Al alloys. The strength of Zn alloys increases as the Cu content increases due to the increased content and size of the second phase in the Zn alloys. This means that the mechanical properties of Zn alloys can be adjusted by a continuous casting and extrusion process, and the improvement of equipment capacity can improve the structure and morphology of the alloys. [ABSTRACT FROM AUTHOR]

This manuscript presents a model of a system implementing individual stages of production for long steel products resulting from rolling. The system encompasses the order registration stage, followed by production planning based on information about the billet inventory status, then offers the possibility of scheduling orders for the melt shop in the form of melt sequences, manages technological knowledge regarding the principles of sequencing, and utilizes machine learning and optimization methods in melt sequencing. Subsequently, production according to the implemented plan is monitored using IoT and vision tracking systems for ladle tracking. During monitoring, predictions of energy demand and energy consumption in LMS processes are made concurrently, as well as predictions of metal overheating at the CST station. The system includes production optimization at two levels: optimization of the heat sequence and at the production level through the prediction of heating time. Optimization models and machine learning tools, including mainly neural networks, are utilized. The system described includes key components: optimization models for sequencing heats using Ant Colony Optimization (ACO) algorithms and neural network-based prediction models for power-on time. The manuscript mainly focuses on process modeling issues rather than implementation or deployment details. Machine learning models have significantly improved process efficiency and quality; the optimization of planning has reduced sequencing plan execution time; and power-on time prediction models estimate the main ladle heating time with 97% precision, enabling precise production control and reducing overheating. The system serves as an example of implementing the concept of a cyber–physical system. [ABSTRACT FROM AUTHOR]

The growing use of aluminum and its compounds has increased the volume of aluminum waste. To mitigate environmental impacts and cut down on manufacturing expenses, extensive investigations have recently been undertaken to recycle aluminum compounds. This paper outlines the outcomes of a study on fabricating standard EN AW-2007 alloy using industrial and secondary scrap through continuous casting. The resultant recycled bars were analyzed for their chemical makeup and examined for microstructural features in both the cast and T4 states, undergoing mechanical property evaluations. The study identified several phases in the cast form through LM, SEM + EDS, and XRD techniques: Al7Cu2Fe, θ-Al2Cu, β-Mg2Si, Q-Al4Cu2Mg8Si7, and α-Al15(FeMn)3 (SiCu)2, along with Pb particles. Most primary intermetallic precipitates such as θ-Al2Cu, β-Mg2Si, and Q-Al4Cu2Mg8Si7 dissolved into the α-Al solid solution during the solution heat treatment. In the subsequent natural aging process, the θ-Al2Cu phase predominantly emerged as a finely dispersed hardening phase. The peak hardness achieved in the EN AW-2007 alloy was 124.8 HB, following a solution heat treatment at 500 °C and aging at 25 °C for 80 h. The static tensile test assessed the mechanical and ductility properties of the EN AW-2007 alloy in both the cast and T4 heat-treated states. Superior strength parameters were achieved after solution heat treatment at 500 °C for 6 h, followed by water quenching and natural aging at 25 °C/9 h, with a tensile strength of 435.0 MPa, a yield strength of 240.5 MPa, and an appreciable elongation of 18.1% at break. The findings demonstrate the feasibility of producing defect-free EN AW-2007 alloy ingots with excellent mechanical properties from recycled scrap using the continuous casting technique. [ABSTRACT FROM AUTHOR]

To improve the strength of the metal while maintaining good plasticity, helical fibers are added to the metal matrix. How to form helical fiber and control its parameters in the preparation process are urgent problems to be solved in the study of helical fiber-reinforced metal matrix composites. In this paper, the continuous casting process of helical fiber-reinforced metal matrix composites was proposed. To reduce the difficulty of the experiment, the formation process of helical fiber on metal matrix and the relationship between the continuous casting process parameters and helical shape fiber parameters were studied by preparing helical carbon fiber-reinforced lead matrix composites with a low-melting-point metal matrix. The results show that this process can produce helical fiber-reinforced metal matrix composite stably and continuously, and the helical shape parameters of the composite can be controlled by changing the process parameters of continuous casting. To further improve the practical application of this process, helical carbon fiber-reinforced aluminum matrix composites were prepared. The test result in terms of mechanical property shows that the tensile strength and elongation of the composite were improved. This indicates that the reinforced phase of the helical structure of the metal matrix composite has higher strength and toughness compared with the matrix metal. [ABSTRACT FROM AUTHOR]

ŠTORE STEEL Ltd. is one of the three steel plants in Slovenia. Continuous cast 180 mm × 180 mm billets can undergo cooling to room temperature using a turnover cooling bed. They can also be cooled down under hoods or heat treated to reduce residual stresses. Additional operations of heat treatment from 36 h up to 72 h and cooling of the billets for 24 h, with limited capacities (with only two heat treatment furnaces and only six hoods), drastically influence productivity. Accordingly, the casting must be carefully planned (i.e., the main thing is casting in sequences), while the internal quality of the billets (i.e., the occurrence of inner defects) may be compromised. Also, the stock of billets can increase dramatically. As a result, it was necessary to consider the abandoning of cooling under hoods and heat treatment of billets. Based on the collected scrap data after ultrasonic examination of rolled bars, linear regression and genetic programming were used for prediction of the occurrence of inner defects. Based on modeling results, cooling under hoods and heat treatment of billets were abandoned at the casting of several steel grades. Accordingly, the casting sequences increased, and the stock of billets decreased drastically while the internal quality of the rolled bars remained the same. [ABSTRACT FROM AUTHOR]

The study investigates the effect of pulsed magnetic fields on undissolved carbides in high-carbon chromium bearing steel GCr15 billets. The billets were subjected to heat treatment at 950 °C, with a pulsed magnetic field of varying durations applied during the process. The influence of the pulsed magnetic field on the distribution of undissolved carbides within the billets was investigated, and the thermodynamic and kinetic mechanisms of undissolved carbides dissolution were explored. The results indicate that the area percentage of undissolved carbides in the microstructure decreases from 1.68% to 0.06% after applying a pulsed magnetic field for 10 min, and the size of undissolved carbides decreases from 17.5 μm to 4.9 μm. When a pulsed magnetic field is applied for 30 min, all undissolved carbides dissolve. The statistics demonstrate that the average size of undissolved carbides is reduced from 14.19 μm to 0.63 μm, with a reduction percentage reaching 96%. Over the same duration, the number density of the undissolved carbides decreases from (0.19~0.55)/mm2 to (0.03~0.1)/mm2, and the percentage area of the undissolved carbides decreases from (1.26~1.68)% to (0~0.02)%. Thermodynamically, applying a pulsed magnetic field lowers the dissolution energy barrier of undissolved carbides and modifies their transformation temperature. Kinetically, the rate of alloy element diffusion is enhanced by increasing the frequency of atomic jumps. This research aims to provide new insights into enhancing the contact fatigue life of bearing steel, increasing the proportion of special steel, and optimizing the steel deep-processing process. [ABSTRACT FROM AUTHOR]

Submerged entry nozzle (SEN) clogging will affect the production efficiency and product quality in the continuous casting process. In this work, the transient SEN clogging model is developed by coupling the porous media model defined by the user-defined function (UDF) and the discrete phase model (DPM). The effects of the transient SEN clogging process on the flow field, the distribution of argon gas bubbles and the fluctuation of the interface between steel and slag in the concave bottom SEN in the continuous casting slab mold with a cross-section of 1500 mm × 230 mm are studied by coupling transient SEN clogging model, DPM and volume of fluid (VOF) model. The results show that the actual morphology and thicknesses of SEN clogging are in good agreement with the numerical simulation results. The measurement result of the surface velocity is consistent with the numerical simulation result. With increasing the simulation time, the degree of SEN clogging increases. The flow velocities of molten steel flowing from the outlet of the side hole increase, because the flow space is occupied with the clogging inclusions, which leads to the increased number of argon gas bubbles near the narrow wall. The steel–slag interface fluctuation near the narrow walls also increases, resulting in the increased risk of slag entrapment. [ABSTRACT FROM AUTHOR]

Economic limitations often hinder the extensive use of fiber-reinforced concrete in full-scale structures. Addressing this, the present study explored localized reinforcement at critical interfaces, deploying a novel synchronized casting mold that deviates from segmented casting interface studies. The research prioritized the flexural, compressive, and shear characteristics at the interface between fiber-reinforced concrete and ordinary concrete with continuous casting. The results demonstrated that polyethylene (PE) fibers significantly enhance anti-cracking capabilities, surpassing steel fibers in all mechanical tests. PE fibers' high modulus of elasticity and tensile strength considerably augmented the interface's bending resistance, facilitating better load transfer and capitalizing on the fibers' tensile properties. Additionally, their low density and greater dispersion negated the sinking behavior typical of steel fibers, thereby strengthening the compressive capacity of the interface. Although a 0.75% PE fiber volume is ideal for ductility, volumes as low as 0.25% or 0.5% are economically viable if dispersion is optimal. Conversely, steel fibers, prone to sinking and clustering, offer inferior shear resistance at the interface than PE fibers, marking a significant finding for structural applications. [ABSTRACT FROM AUTHOR]

Ag-Sn-In-Ni-Te alloy ingots were produced through a heating–cooling combined mold continuous casting technique; they were then drawn into wires. However, during the drawing process, the alloy wires tended to harden, making further diameter reduction challenging. To overcome this, heat treatment was necessary to soften the previously drawn wires. The study investigated how variations in heat treatment temperature and holding time affected the microstructure, microhardness and corrosion resistance of the alloy wires. The results indicate that the alloy wires subjected to heat treatment at 700 °C for 2 h not only exhibited a uniform microstructure distribution, but also demonstrated low microhardness and excellent corrosion resistance. [ABSTRACT FROM AUTHOR]

Secondary cooling electromagnetic stirring (S-EMS) significantly impacts the internal quality of continuous casting slabs. In order to investigate the effects of S-EMS modes on segregation in slabs, a three-dimensional numerical model of the full-scale flow field, solidification, and mass transfer was established. A comparative analysis was conducted between continuous electromagnetic stirring and alternate stirring modes regarding their impacts on steel flow, solidification, and carbon segregation. The results indicated that adopting the alternate stirring mode was more advantageous for achieving uniform flow fields and reducing the disparity in solidification endpoints, thus mitigating carbon segregation. Specifically, the central carbon segregation index under continuous stirring at 320 A was 1.236, with an average of 1.247, while under alternate stirring, the central carbon segregation index decreased to 1.222 with an average of 1.227. [ABSTRACT FROM AUTHOR]

As the main energy-consuming equipment, the reheating furnace plays an important role in the scheduling of continuous casting and hot rolling for a steel mill. This paper studies the energy consumption of cold and hot slab conversion mode in a reheating furnace, forming four conversion relationships, with the goal of minimizing the coupling function between the maximum completion time of the hot rolling and the energy waste of the reheating furnace, and modelling the scheduling of a continuous casting–hot rolling process. An improved ordered pair bat algorithm is used to solve for special process conditions of the proposed scheduling model. The effectiveness of the proposed model and algorithm is verified by solving the different slab charging sequence and conversion mode. Moreover, a comparative study of different types of batches is also conducted, and it is found that the model can save more than 5000 GJ per month for the steel mill, which can achieve the goal of effective energy saving and increasing enterprise profit. [ABSTRACT FROM AUTHOR]

During continuous slab casting, strand electromagnetic stirring (S-EMS) has a significant effect on improving the slab quality. In the current work, a numerical model based on the practical slab continuous casting machine and coupled electromagnetic field, flow field, solidification, and solute transport was established to investigate and evaluate the effect of the S-EMS installation position with various current intensities on metallurgical behavior. The model was verified by magnetic field measurement, infrared camera, and nail shooting experiments. The results show that moving the S-EMS installation position to the solidification end reduces the stirring effect due to the skin effect and the increasing thickness of the slab shell. A higher installation position is beneficial for improving the equiaxed grain rate, while a lower one is beneficial for reducing carbon segregation. The maximum segregation index and range decrease from 1.26 to 1.2 and from 0.42 to 0.36 with the installation position being decreased from −3 m to −12.8 m, respectively. The industrial trials show that S-EMS installed at 3 m has a significant effect on expanding the equiaxed grain zone and a deteriorating effect on reducing carbon segregation. [ABSTRACT FROM AUTHOR]

In this study, a novel crawler-type continuous casting (CC) technology was designed to efficiently and cost-effectively produce bulk metallic glass (BMG) slabs. As a crucial process parameter, casting temperature has a significant impact on the operation of CC devices and the quality of slabs. CC experiments of the Zr41.2Ti13.8Cu12.5Ni10.0Be22.5 (Vit1) BMG slab were carried out at the casting temperatures of 1073 K, 1123 K, and 1173 K, and the microstructure and properties of slab samples were analyzed and studied. The experimental results indicate that the BMG slabs can be prepared by CC at 1173 K and 1123 K. When the temperature is reduced to 1073 K, the Be12Ti crystal phase precipitates inside the CC slab, which has a certain impact on the thermal stability and compressive performance of the slab. The control of casting temperature does not affect the glass-forming ability (GFA) of the slab in the CC process. [ABSTRACT FROM AUTHOR]

Longitudinal cracks are a common defect on the surface of continuous casting slabs, and cause increases in additional processing costs or long-time interruptions. The accurate identification of surface longitudinal cracks is helpful to ensure the casting process is adjusted in time, which significantly improves the quality of slabs. In this research, the typical temperature characteristics of thermocouples at the position of longitudinal cracks and their adjacent locations were extracted. The principal component analysis (PCA) method was used to reduce the dimensions of these characteristics to remove the redundant information. The particle swarm optimization (PSO) method was introduced to optimize the parameter. On this basis, a recognition model of surface longitudinal cracks was established, based on a particle swarm optimization–eXtreme gradient boosting (XGBOOST) model. Finally, this model was trained and tested using longitudinal crack and non-longitudinal crack samples and compared with the decision tree, the gradient boosting decision tree (GBDT) and XGBOOST models. The test results showed that PSO-XGBOOST had the best identification performance in all evaluation indexes. The accuracy, F1 score and alarm rate results were 95.8%, 92.3% and 100%, respectively, and the false alarm rate was as low as 5.5%. The research results provide a theoretical basis and a reliable model for surface longitudinal crack identification. [ABSTRACT FROM AUTHOR]

This study proposed a new method for homogenizing continuous casting blooms based on solidification simulation calculations and industrial tests. The text describes a theoretical analysis of the solidification route of a cast billet of high-carbon alloy steel (B300A) under different process conditions. It summarizes the changing law of different under-pressure process parameters and under-pressure efficiency. The text also presents a solution to the seriousness of center shrinkage defects in the continuous casting of a large square billet of high-carbon alloy steel with the synergistic control technology of mixed light and heavy mixing under pressure. The study indicates that the center carbon segregation index of a high carbon steel continuous casting billet is 1.05, with a carbon extreme difference of not more than 0.08% and a proportion of 98.4%. Additionally, the center shrinkage is not more than a 0.5 level with a proportion of 99.5%. Meanwhile, the internal quality of cast billets has been improved, allowing for the rolling of large-size bars with a low consolidation ratio. The pass rate for internal ultrasonic flaw detection using the GB/T4162A grade is now higher than 99.95%, significantly reducing process costs and improving production efficiency for continuous casting and rolling. [ABSTRACT FROM AUTHOR]

The Hazelett continuous casting and rolling process represents a leading-edge production method for cold-rolled aluminum sheet and strip billets in the world. Its solidification microstructure significantly influences the quality of billets produced for cold rolling of aluminum sheets and strips. In this study, employing the CAFE (Cellular Automaton—Finite Element) method, we developed a coupled computational model to simulate the solidification microstructure in the Hazelett continuous casting process. We investigated the impact of nucleation parameters, casting temperature, and continuous casting speed on the microstructural evolution of the continuous casting billet. Through integrated metallographic analyses, we aimed to elucidate the controlling mechanisms underlying the Hazelett continuous casting process and its resultant microstructure. The results demonstrate that the equiaxed rate of grains increases with an increase in nucleation density, and the grain size decreases under constant cooling strength. With other nucleation parameters held constant, the grain size decreases as undercooling increases, and the columnar crystal zone expands. The nucleation density of the Hazelett continuous casting aluminum alloy has been determined to range between 1011 m−3 and 1013 m−3, and the undercooling ranges between 1 °C and 2.5 °C. The solidified grain structure can be controlled between 35 μm and 72 μm. The grain size of the continuous casting billet increases with an increase in pouring temperature and decreases as the casting speed increases. Elevating the pouring temperature positively impacts the fraction of high-angle grain boundaries and promotes the dendritic to equiaxed grain transition. Moreover, there exists potential for further optimization of continuous casting process parameters. [ABSTRACT FROM AUTHOR]

Electromagnetic continuous casting technology serves as a significant means for enhancing the casting performance of 2219 aluminum alloy. Investigating the influence of electromagnetic field variations on the solidification process is crucial for studying the microstructure and mechanical properties of electromagnetic cast billets. Through experimental research, variations in the microstructure and mechanical properties were examined for ordinary direct chill casting, as well as three different electromagnetic power casting ingots. The COMSOL software (COMSOL Multiphysics 6.0) was utilized to simulate the temperature and flow field, enabling an explanation of the resulting performance changes. The results showed the effect on electromagnetic continuous casting technology by the electromagnetic field generated by the Lorentz force and melt stirring, improving the melt flow and temperature distribution so that the melt center and the edge of the melt forcible convection were enhanced, thus realizing the tissue refinement, mechanical properties, and Cu element segregation of the improvement. With an increase in electromagnetic power, the distribution of the temperature field was more homogeneous, the segregation phenomenon was more alleviated, and the improvement in mechanical properties was more significant. The optimal microstructure and mechanical properties were achieved at a power of 20.0 kW, with a 74.7% improvement in grain refinement in the center and a tensile strength increase of 30.8%. Additionally, significant improvements were observed in segregation phenomena. [ABSTRACT FROM AUTHOR]

This study presents the development of a novel material for a spherical impact pad for tundishes during steel production, focusing on improving steel cleanliness and flow optimization. Traditional low-carbon and ultra-low carbon concrete (LCC/ULCC) materials are replaced with a new cement-free mixture, utilizing a sol–gel method binder. This innovative approach leads to the creation of IPC TECAST BPV CST, a refractory concrete with enhanced resistance to corrosion and shape stability under extreme conditions. The material's effectiveness is demonstrated through operational tests, showing remarkable durability and no erosion defects after extensive use in casting liquid metal. The sol–gel binder significantly reduces the carbon footprint and energy consumption during the drying process, compared to traditional concretes. This study concludes that the new material not only withstands the dynamic environment of liquid steel but also ensures consistent dynamic flow conditions throughout the steel casting process, marking a significant advancement in tundish impact pad technology. [ABSTRACT FROM AUTHOR]

In this paper, the fluid flow, slag entrainment and solidification process in a slab mold were studied using physical modeling and numerical simulation. The effect of two types of submerged entry nozzles (SENs) was also studied. The results showed that the surface velocity for type A SEN was larger than that using type B SEN. For type A SEN, the maximum surface velocity was 0.63 m/s and 0.56 m/s, and it was 0.20 m/s and 0.18 m/s for type B SEN. The larger shear effect on the top surface made the slag at narrow face impacted to the vicinity of 1/4 wide face, while the slag layer at the top surface was relatively stable for type B SEN. Increasing the immersion depth of SEN decreased the surface velocity and slag entrainment. For type A SEN, the thickness of the solidified shell at the narrow face of the mold outlet was thin (12.3 mm) and there was a risk of breakout. For type B SEN, the liquid steel with high temperature would flow to the meniscus and it was beneficial to the melting of the mold flux. The thickness of the solidified shell at the narrow face of the mold outlet was increased. Furthermore, the surface velocity was also increased and it was not recommended for high casting speed. [ABSTRACT FROM AUTHOR]

Exploring the mechanism of the α-ferrite precipitation process on high-temperature properties plays an important guiding role in avoiding slab cracks and effectively regulating quality. In this work, in situ observation of the α-ferrite sustained precipitation behavior for peritectic steel during the austenitic phase transition process has been investigated using high-temperature confocal scanning laser microscopy. Meanwhile, the high-temperature evolution of the phase fractions during the phase transition process was quantitatively analyzed based on the high-temperature expansion experiment using the peak separation method. Furthermore, the high-temperature properties variations of the casting slab during the α-ferrite sustained precipitation process were investigated with the Gleeble thermomechanical simulator. The results show that the film-like ferrite precipitated along the austenite grain boundaries at the initial stage of phase transition, then needle-like ferrite initiates rapid precipitation on film-like ferrite when the average thickness reaches 15~20 μm. Hot ductility reached a minimum at the ferrite phase fraction fα = 10~15%, while high-temperature properties returned to a higher level after fα > 40~45%. The appearance of a considerable amount of needle-like ferrite and grain refinement effectively improves the high-temperature properties with the α-ferrite precipitation process advances. [ABSTRACT FROM AUTHOR]

The bearing steel's high-temperature brittle zone (1250 °C–1100 °C), second brittle zone (1100 °C–950 °C), and low-temperature brittle zone (800 °C–600 °C) were determined by the reduction in area and true fracture toughness. The crack sensitivity was strongest at temperatures of 1200 °C, 1000 °C, and 600 °C, respectively. Various experimental and computational methods were used to establish the phase type, microstructure, size, and mechanical properties of carbides in bearing steel. The critical conditions for crack initiation in the matrix (FCC-Fe, FCC-Fe, and BCC-Fe)/carbides (striped Fe0.875Cr0.125C, netted Fe2.36Cr0.64C, and spherical Fe5.25Cr1.75C3) were also investigated. The values for the high-temperature brittle zone, the second brittle zone, and the low-temperature brittle zone were 13.85 MPa and 8.21 × 10−3, 4.64 MPa and 6.52 × 10−3, and 17.86 MPa and 1.86 × 10−2, respectively. These were calculated using Eshelby's theory and ABAQUS 2021 version software. The ability of the three carbides to cause crack propagation was measured quantitatively by energy diffusion: M3C > MC > M7C3. This study analyzed the mechanism of carbide precipitation on the formation of high-temperature cracks in bearing steel casting. It also provided the critical conditions for carbide/matrix interface cracks in bearing steel continuous casting, thus providing effective support for improving the quality of bearing steel casting. [ABSTRACT FROM AUTHOR]

The intermediate-temperature embrittlement range was examined for Fe, Al, Cu, and Ni alloys. It was found that this embrittlement occurs in many alloys, although the causes are very diverse. Embrittlement can be due to fine matrix precipitation, precipitate free zones, melting of compounds at the grain boundaries, segregation of elements to the boundaries, and, additionally for steel, the presence of the soft ferrite film surrounding the harder austenite matrix. Grain boundary sliding and segregation to the boundaries seem to dominate the failure mode at the base of the trough when intergranular failure takes place. When cracking is due to the presence of hydrogen or liquid films at the boundary, then the dissociation along the boundaries is so easy, it is often independent of the strain rate and is always intergranular. In the other cases when failure occurs, if the deformation is carried out at a high strain rate, it is normally transgranular (e.g., hot rolling giving rise to edge cracking). However, when the strain rate is reduced to that of creep (e.g., bending during continuous casting of steel), failure can also take place by grain boundary sliding, and intergranular failure then becomes the favoured mode. [ABSTRACT FROM AUTHOR]

Primary dendrite information is one of the most important metrics to measure the quality of continuous cast slabs. The contrast of low magnification images is very low under the influence of illumination and sampling devices, so the traditional dendrite detection method has the problem of missed detections. We propose an automatic dendrite detection method based on an improved Hough transform, which effectively improves the accuracy and efficiency of primary dendrite detection. By using the local grayscale features of the image, a genetic algorithm-based local contrast enhancement algorithm is proposed. Compared with the traditional contrast enhancement algorithm, it can retain all the information of the dendrites. Combined with the image binarization method based on Hessian matrix, we can obtain more detailed information about the dendrites. According to the continuity and solidification characteristics of dendrites, the Hough transform is improved to extract dendrite information, which effectively reduces the computational cost of the Hough transform. The experimental results show that the method of this paper has versatility, and the error is four pixels compared with the manual method, which can provide a reliable basis for the subsequent judgement of the quality of cast billets. [ABSTRACT FROM AUTHOR]

The plasma rotating electrode process (PREP) is an ideal method for the preparation of metal powders such as nickel-based, titanium-based, and iron-based alloys due to its low material loss and good degree of sphericity. However, the preparation of silver alloy powder by PREP remains challenging. The low hardness of the mould casting silver alloy leads to the bending of the electrode rod when subjected to high-speed rotation during PREP. The mould casting silver electrode rod can only be used in low-speed rotation, which has a negative effect on particle refinement. This study employed continuous casting (CC) to improve the surface hardness of S800 Ag (30.30% higher than mould casting), which enables a high rotation speed of up to 37,000 revolutions per minute, and silver alloy powder with an average sphericity of 0.98 (5.56% higher than gas atomisation) and a sphericity ratio of 97.67% (36.28% higher than gas atomisation) has been successfully prepared. The dense S800 Ag was successfully fabricated by laser powder bed fusion (LPBF), which proved the feasibility of preparing high-quality powder by the "CC + PREP" method. The samples fabricated by LPBF have a Vickers hardness of up to 271.20 HV (3.66 times that of mould casting), leading to a notable enhancement in the strength of S800 Ag. In comparison to GA, the S800 Ag powder prepared by "CC + PREP" exhibits greater sphericity, a higher sphericity ratio and less satellite powder, which lays the foundation for dense LPBF S800 Ag fabrication. [ABSTRACT FROM AUTHOR]

The influence of Ti on the behavior of hot ductility was examined in four different Ti-containing micro-alloyed steels with a constant content of Nb. Thermomechanical investigations using a dilatometer were carried out to simulate the conditions during casting and cooling in the strand of a continuous caster with temperatures in the range of 650–1100 °C, strain rates of 0.01 s−1 and 0.001 s−1, and reheating rates between 60 and 180 Kmin−1. To understand the fracture mechanism, optical (LOM) and scanning electron microscopy (SEM), elemental analysis via energy dispersive X-ray spectroscopy (EDX), MatCalc "Scheil–Guilliver" calculations, and precipitation kinetics calculations were carried out for the critical conditions, showing low hot ductility between Ar3 and Ae3 temperatures and a brittle to ductile transition temperature at 900 °C. The existence of TiNb(CN), thin ferrite formation, and grain boundary sliding (GBs) due to limited dynamic recrystallization (DRX) has been documented and discussed. As a result, the reheating rate has no sufficient effect on the ductility. The existence of Nb-rich TiNb(CN) of sizes below ~1 μm triggers brittle fracture by increasing the frequency of micro-voids around grain boundaries. It can be stated that if the conditions in the hot ductility trough are avoided, the addition of Ti and high strain support minimize the risk of crack formation. [ABSTRACT FROM AUTHOR]

Al 6082 aluminum alloy has excellent corrosion resistance, strength, and formability. However, owing to the recrystallization effect of a hot working process, coarse grains form easily in this material, which reduces its strength and service life. The novel continuous casting direct rolling (CCDR) method can prevent the deterioration of this material. Thus, we used CCDR Al 6082 aluminum alloy as the research material in this study. By subjecting a CCDR Al 6082 aluminum alloy to heat treatment (T4 and T6) and cold rolling, the influence of recrystallization effect on its mechanical properties and on impact failure resistance were explored. The results demonstrated that the specimen subjected to T4 heat treatment had a higher elongation and that the specimen subjected to T6 heat treatment had a higher strength. After cold rolling, the hardness and strength of the specimens subjected to different heat treatments (coded T4R4 and T6R4) increased because of the work's hardening effect. Moreover, the elongations of both specimens decreased, but they were higher than the industrial standard (>10%). The strength of specimen T6R4 was higher (up to 400 MPa) than specimen T4R4. Moreover, relative to specimen T4R4, specimen T6R4 had greater tensile and Charpy impact failure toughness. [ABSTRACT FROM AUTHOR]

The control of the solidification structure of a casting billet is directly correlated with the quality of steel. Variations in superheat can influence the transition from columnar crystals to equiaxed crystals during the solidification process, subsequently impacting the final solidification structure of the billet. In this study, a model of microstructure evolution during billet solidification was established by combining simulation and experiment, and the dendrite growth microstructure evolution during billet solidification under different superheat was studied. The results show that when the superheat is 60 K, the complete solidification time of the casting billet from the end of the 50 mm section is 252 s, when the superheat is 40 K, the complete solidification time of the casting billet is 250 s, and when the superheat is 20 K, the complete solidification time of the casting billet is 245 s. When the superheat is 20 K, the proportion of the equiaxed crystal region is higher—the highest value is 53.35%—and the average grain radius is 0.84556 mm. The proportion of the equiaxed crystal region decreases with the increase of superheat. When the superheat is 60 K, the proportion of the equiaxed crystal region is the lowest—the lowest value is 46.27%—and the average grain radius is 1.07653 mm. Proper reduction of superheat can obviously reduce the size of equiaxed crystal, expand the area of equiaxed crystal and improve the quality of casting billet. [ABSTRACT FROM AUTHOR]

Understanding the phenomena that cause jet oscillations inside funnel-type thin-slab molds is essential for ensuring continuous liquid steel delivery, improving flow pattern control, and increasing plant productivity and the quality of the final product. This research aims to study the effect of the nozzle's internal design on the fluid dynamics of the nozzle-mold system, focusing on suppressing vorticity generation below the nozzle's tip. The optimized design of the nozzle forms the basis of the results obtained through numerical simulation. Mathematical modeling involves fundamental equations, the Reynolds Stress Model for turbulence, and the Multiphase Volume of Fluid model. The governing equations are discretized and solved using the implicit iterative-segregated method implemented in FLUENT®. The main results demonstrate the possibility of controlling jet oscillations even at high casting speeds and deep dives. The proposed modification in the internal geometry of the nozzle is considered capable of modifying the flow pattern inside the mold. The geometric changes correspond with 106% more elongation than the original nozzle; the change is considered 17% of an inverted trapezoidal shape. Furthermore, there was a 2.5 mm increase in the lower part of both ports to compensate for the inverted trapezoidal shape. The newly designed SEN successfully eliminated the issue of jet oscillations inside the mold by effectively preventing the intertwining of the flow. This improvement is a significant upgrade over the original design. At the microscale, a delicate force balance occurs at the tip of the nozzle's internal bifurcation, which is influenced by fluctuating speeds and ferrostatic pressure. Disrupting this force balance leads to increased oscillations, causing variations in the mass flow rate from one port to another. Consequently, the proposed nozzle optimization design effectively controls microscale fluctuations above this zone in conjunction with changes in flow speed, jet oscillation, and metal–slag interface instability. [ABSTRACT FROM AUTHOR]

The influence of centerline segregation on the low-temperature impact toughness of the heat-affected zone (HAZ) of welded joints was studied by welding experiments on X70 steel plates rolled from continuous casting slabs with segregation grades of class 2 and class 3. The experimental results show that the impact toughness at HAZ from class 2 slab steel plate is more stable and has excellent low-temperature toughness than that of class 3 slab steel plate. The impact toughness of the HAZ of the class 3 slab steel plate is low to 100 J at −40 °C and has a severe fluctuation range (~150 J), and the delamination phenomenon is also observed in the fracture cross-section. The reason for this phenomenon is due to the enrichment of C and Mn elements in the centerline segregation zone. The formation of abnormal microstructure (martensite/bainite) in the segregation zone leads to stress concentration, which easily weakens the low-temperature toughness of the joint. [ABSTRACT FROM AUTHOR]

A mathematical model of the macrosegregation of continuous cast high carbon steel billet was developed based upon a representative volume element, considering the flow of enriched liquid, solidification rate, and solidification shrinkage as well. It was found that a lower casting velocity, higher cooling intensity, and shorter solidification interval positively contributed to the inhibition of macrosegregation in a continuously cast billet when a mechanical reduction process was not applied. A numerical expression for the relative flow velocity of liquid was further proposed incorporating such aspects as casting velocity, densities of different phases, and the variation of cross section areas as well. The analysis based on this numerical expression indicated that the overall effect of the reduction process on the macrosegregation of billets depended not only on the reduction zone but also on the reduction amount and its distribution for the active reduction rolls. The test results of further practical plant trials demonstrated a reasonable agreement with the predictions obtained from the proposed numerical model, indicating the reliability of this analysis model to be employed for the continuous casting of high carbon steel billet with strand reduction process. [ABSTRACT FROM AUTHOR]

Grain-oriented electrical steel (GOES) has been used for many years for application in transformed cores due to its excellent magnetic properties. Magnetic properties are strongly influenced by obtaining a texture with a certain orientation (110) [001] for BCC structure. This is related to the easy direction of magnetization [001]. So far, the main research has been focused on obtaining a strong texture in the last stages of the process. The aim of the present study was to additionally trace textural changes for a slab after the continuous casting (CC) process and for a sheet after the hot rolling process. The scope of such an analysis has not been conducted before. With regard to the state after continuous casting (CC), the texture was related to measurements of the anisotropy of Barkhausen magnetic noises and the macrostructure of the slab. Based on the X-ray diffraction examinations that compared the texture intensity calculated from the texture coefficient of the slab, the hot rolled steel and the final product of grain-oriented electrical steel contained 3.1% of Si. The studies performed with the material taken from three different production steps showed high differences in the values of textural intensity indicating the occurrence of a crystallization texture, especially in the area of the columnar crystal zone; textural weakness after the hot rolling process and high texturing in the final product for textural components corresponding to the desired Goss texture. [ABSTRACT FROM AUTHOR]

In this study, a three-dimensional segmented coupled model for continuous casting billets under combined mold and final electromagnetic stirring (M-EMS, F-EMS) was developed. The model was verified by comparing carbon segregation in billets with and without EMS through plant experiments. The findings revealed that both M-EMS and F-EMS induce tangential flow in molten steel, impacting solidification and solute distribution processes within the billet. For M-EMS, with operating parameters of 250A-2Hz, the maximum tangential velocity (velocity projected onto the cross-section) was observed at the liquid phase's edge. For F-EMS, with operating parameters of 250A-6Hz, the maximum tangential velocity occurred at f l = 0.7 . Furthermore, F-EMS accelerated heat transfer in the liquid phase, reducing the central liquid fraction from 0.93 to 0.85. M-EMS intensified the washing effect of molten steel on the solidification front, resulting in the formation of negative segregation within the mold. F-EMS significantly improved the centerline segregation issue, reducing carbon segregation from 1.15 to 1.02. Experimental and simulation results, with and without EMS, were in good agreement, indicating that M+F-EMS leads to a more uniform solute distribution within the billet, with a pronounced improvement in centerline segregation. [ABSTRACT FROM AUTHOR]

The heat transfer of a slab is significantly influenced by roll contact during the continuous casting process. The influence of roll contact calculation methods on the predicted heat transfer results has not been previously investigated. In this work, the non-uniform solidification of the wide-thick slab was studied with a 2D heat transfer model using real roll contact method (R. method) and equivalent roll contact method (E. method). The predicted slab surface temperature and shell thickness were verified with the measured results of the infrared camera and nail shooting experiments, respectively. Then, the predicted heat transfer results (including the slab surface temperature, mushy region length, and solidification end position) for the wide-thick slab with different thicknesses and different casting speeds were calculated using the E. method and R. method, and the influence of these two roll contact methods on the predicted heat transfer results was discussed for the first time. The results show that both these two roll contact methods could be applied to accurately predict the slab surface temperature without considering the transient temperature dips in the roll–slab contact regions. However, the deviation of the predicted mushy region length and solidification end position using the E. method are obvious. Compared with the R. method, the predicted mushy region length obtained using the E. method is larger and the solidification end obviously subsequently moves along the casting direction. [ABSTRACT FROM AUTHOR]

This work studies how the sliding-gate valve (SGV) modifies the features and the dynamic behavior of the outlet jets for flat-bottom and well-bottom bifurcated submerged entry nozzles (SENs) used in continuous casting machines. Three conditions for the SGV were studied: no obstruction, moderate obstruction, and severe obstruction. The experimental study used a scaled model, employing cold water as the working fluid. A high-frequency analysis of the flow inside the SEN's bore arriving at the outlet ports was performed by employing the particle image velocimetry (PIV) technique. Low-frequency measurements of the volumetric flow at the exit port were obtained by splitting the exit jet into four quadrants and employing digital flowmeters. It was observed that reducing the SGV clearance increases the turbulence of the flow inside the SEN bore, but the flow displays ordered rather than erratic fluctuations. Flowmeter measurements showed that, regardless of the level of obstruction in the SGV, the outlet jets on flat-bottom and the well-bottom SENs have dynamic behaviors and features with significant differences. This finding is relevant because the flow distribution inside the outlet ports is directly related to the jet's wideness, affecting the recirculation pattern inside the mold and, therefore, the quality of the finished steel slab. [ABSTRACT FROM AUTHOR]

The continuous casting tundish is non-isothermal due to heat losses and temperature variation from the inlet stream, which generate relevant convection forces. This condition is commonly avoided through qualitative fluid dynamic analysis only. This work searches to establish the conditions for which non-isothermal simulations are mandatory or for which isothermal simulations are enough to accurately describe the fluid dynamics inside the tundish by quantifying the buoyant and inertial forces. The mathematical model, simulated by CFD software, considers the Navier-Stokes equations, the realizable k-ε model for solving the turbulence, and the Lagrangian discrete phase to track the inclusion trajectories. The results show that temperature does not significantly impact the volume fraction percentages or the mean residence time results; nevertheless, bigger velocity magnitudes under non-isothermal conditions than in isothermal conditions and noticeable changes in the fluid dynamics between isothermal and non-isothermal cases in all the zones where buoyancy forces dominate over inertial forces were observed. Because of the results, it is concluded that isothermal simulations can accurately describe the flow behavior in tundishes when the flow control devices control the fluid dynamics, but simulations without control devices or with a weak fluid dynamic dependence on the control devices require non-isothermal simulations. [ABSTRACT FROM AUTHOR]

Variations in the corrosion behavior of biomedical NiTi alloys in Cl− containing and acidic environments present a problem with their biological implantation. The objective of this research was to evaluate the synergy of the microstructure, the corrosion behavior, and the biocompatibility of novel continuous-cast NiTi alloys and to compare them with commercial NiTi alloys. The two alloys have a practically identical nominal chemical composition, but they differ in production technology. The continuous casting technology involved vacuum induction melting of the basic components and vertical continuous casting, while the commercial NiTi alloy was produced through a process of casting, hot rolling, and forming into square shapes. The microstructure was revealed to determine the surface area and size of grains. The corrosion of a commercial nickel–titanium alloy and one prepared by a novel continuous casting method in acidic and chloride-containing solutions was studied via analytical and electrochemical tests. Localized corrosion characteristics related to oxide properties, when exposed to 9 g L−1 NaCl solution, were examined with focused ion beam analysis and subsequent microchemical analysis of the formed corrosive products. Corrosion potential over time and the oxide film resistance were analyzed using linear polarization measurements. To obtain a preliminary estimate of biocompatibility, human fibroblast cells were used in indirect contact, i.e., alloy conditioning medium. The continuous casting method resulted in a reduction in the average grain size in comparison to the commercial sample and better corrosion stability of the sample in an acidic environment. Also, in a solution of 9 g L−1 NaCl the commercial sample showed high values for the corrosion current density (jcorr = 6 μA cm−2), which indicated low corrosion resistance, while the continuous casting sample possessed much better corrosion stability and lower values for the corrosion current density (jcorr = 0.2 μA cm−2). In line with that, elemental analysis of the corroded surfaces showed higher Cl− ion deposition over the surface layer of the commercial sample, suggesting local oxide breakdown. Moreover, NiTicc reached a value three times higher for polarization resistance (Rp = 270 kΩ cm2) over time in comparison to the commercial sample (Rp~100 kΩ cm2). Biocompatibility evaluation showed that human fibroblast cells exhibited altered metabolic activity. An MTT assay showed that cells' mitochondrial activity dropped below that of control cells in the presence of both materials' supernatants. [ABSTRACT FROM AUTHOR]

This paper is based on the surface defects of casting billets in the production process of nonoriented silicon steel plates at a steel plant in North China. Taking the parameters of a slab mold in the nonoriented silicon steel production process as a prototype, the flow field characteristics of the mold under the same section, different drawing speed and immersion depth were systematically studied by using a LES (large eddy simulation) and VOF (volume of fluid) coupling algorithm. The results show that under the current conditions, when the critical slag entrapment speed increases from 1.0 m/min to 1.2 m/min, the nozzle insertion depth increases linearly with the critical slag entrapment speed, while when the nozzle insertion depth exceeds 130 mm, the increasing effect of further increasing the nozzle insertion depth on the critical slag entrapment speed begins to decrease. When the drawing speed of continuous casting is kept constant at 1.4 m/min, the abnormal fluctuation height of the steel slag interface is significantly improved when the angle of the water nozzle is increased from 15° to 20°, and the proportion of slag entrapment is also reduced from 0.376% to 0.015%. When the nozzle angle is 25°, the slag entrapment ratio is reduced to 0%, and the steel slag interface also ensures a certain activity. The numerical simulation results were applied to the industrial site, and the slag inclusion rate and crack rate of the billet in the continuous casting process of nonoriented silicon steel were obviously improved after the optimization process. [ABSTRACT FROM AUTHOR]

Impurity elimination in tundishes is an essential metallurgical function in continuous casting. If inclusions in a tundish cannot be effectively removed, their presence will have a serious impact on the quality of the bloom. As a result, this research investigates the locations of inclusion particles in a six-strand induction-heating tundish in depth, combining the flow, temperature, and inclusion trajectories of molten steel under electromagnetic fields. The results show that a pinch effect occurred in the induction-heating tundish, and a rotating magnetic field formed in the channel, with a maximum value of 0.158 T. The electromagnetic force was directed toward the center of the axis, and its numerical distribution corresponds to the magnetic flux density distribution, with a maximum value of 2.11 × 105 N/m3. The inclusion particles' movement speed accelerated as the molten steel's temperature rose, and their distribution in the channel was identical to the rotating flow field distribution. When the steel's temperature rose from 1750 K to 1850 K, the removal percentage of inclusion particles in the discharge chamber rose by 9.20%, the removal rate at the outlet decreased from 8.00% to 3.00%, and the adhesion percentage of inclusion particles in the channel decreased from 48.40% to 44.40%. [ABSTRACT FROM AUTHOR]

Carbon segregation is the major and classical internal defect in the continuous casting process of carbon steel. Based on the combined electromagnetic stirring equipment for new billet in a steel plant, China, the influence of combined electromagnetic stirring (M-EMS + F-EMS) on the carbon segregation of 300 mm × 340 mm special-shaped billet was studied via numerical simulation and on-site industrialization tests. The Lorentz force and carbon solute distribution were simulated under different EMS parameters. The formation mechanism of the carbon segregation of medium carbon steel with different combined electromagnetic stirring processes was analyzed. The results show that: (1) with the combined action of "solute flushing" effect and gravity, the carbon concentration in the loose side of the medium carbon steel casting billet is gradually lower than the fixed side, while the carbon concentration on the fixed side gradually accumulates more; and (2) under the action of combined electromagnetic stirring, the segregation index of casting billet could be controlled to remain between 0.96–1.05 and shows an increasing change in solidification from the skin to the center. When the current and frequency of M-EMS are 250 A and 2.0 Hz and the F-EMS are 180 A and 8.0 Hz, the carbon segregation defects in the special-shaped (300 mm × 340 mm) casting billet can be significantly improved. [ABSTRACT FROM AUTHOR]

A three-dimensional model is established to investigate the effect of argon injection mode, argon flow rate and casting speed on the gas–liquid two-phase flow behavior inside a slab continuous casting mold. The Eulerian–Eulerian model is employed to simulate the gas–liquid flow, and the population balance model is applied to describe the bubble breakage and coalescence process in the mold. The numerical simulation results of the bubble size distribution are verified using the water model experiment. The results show that the flow field and bubble distribution are similar between the argon injection at the upper submerged entry nozzle (SEN) and tundish upper nozzle (TUN), while the number density is larger for the argon injection of TUN. The coalescence rate of bubbles and the bubble size inside the mold increase with increasing argon flow rate. When the argon flow rate exceeds 4 L/min, the flow pattern of liquid steel changes from double-roll flow to complex flow, with aggravation of the level fluctuation of the top surface near the SEN. When the casting speed increases, the bubble breakup rate increases and results in a decrease in the size of bubbles inside the mold. At a high casting speed, the flow pattern tends to form double-roll flow, and the liquid level at the narrow face of the top surface increases. [ABSTRACT FROM AUTHOR]

This document is a summary of a special issue of the journal Metals titled "Advances in Molten Metal Refining Process." The issue includes ten articles that cover various aspects of molten metal refining processes, focusing on iron, steel, aluminum, magnesium, and titanium. The articles discuss topics such as the evolution of vortex structures in continuous casting molds, the excitation of micro-scale flow near the solid-liquid interface, the optimization of electrode insertion depths in magnesia furnaces, the behavior of hydraulic jumps during the continuous casting process, the bubble size distribution in single-snorkel furnaces, the refining process of slot-porous matched dual tuyeres, the desulfurization process in Kanbara reactors, the wear and efficiency of graphite rotors in aluminum refinement, and the prediction of bending forces in hot-rolled plates. The articles present mathematical models, numerical simulations, and experimental results to advance the understanding and optimization of molten metal refining processes. [Extracted from the article]