Search

This paper presents the implementation of a two-stage light-emitting diode (LED) driver based on commercial integrated circuits (IC). The presented LED driver circuit topology, which is designed to drive a 150 W LED module, consists of two stages: AC-DC power factor correction (PFC) stage and DC/DC power converter stage. The implementation of the PFC stage uses IC NCP1608, which uses the critical conduction mode to guarantee a unity input power factor with a wide range of input voltages. The DC/DC power converter with soft-switching characteristics for the entire load range uses IC FLS2100XS. Furthermore, the design of an electromagnetic interference (EMI) filter for the LED driver and the dimming control circuit are discussed in detail. The hardware prototype, an LED lighting system, with a rated power of 150 W/32 V from a nominal 220 V/50 Hz AC voltage supply was tested to show the effectiveness of the design. The presented LED driver was tested for street lighting, and the experimental results show that the power factor (PF) was higher than 0.97, the total harmonics distortion (THD) was lower than 7%, and the efficiency was 91.7% at full load. The results prove that the performance of the presented LED driver complies with the standards: IEC61000-3-2 and CIRSP 15:2009.

Currently, oil pollution at sea is one of the serious marine pollution issues that are of great concern to the international community. The incidents of oil exploitation and transportation in the world have become a great threat to the environment in general and ecosystems in particular. Many oil spills have occurred with serious long-term consequences for the ecological environment. Oil pollution in the East Sea in general and oil pollution in the Vietnam Sea in particular are not out of that situation. Marine ecosystems are one of the most important resources for Vietnam's development. However, in recent years, the marine ecosystem has been subject to many negative impacts from the environment, especially the risk of pollution caused by the oil spill when Vietnam is a country with large oil exploitation and import and export activities. In fact, evaluation methods have been widely applied to accurately identify losses. These losses will be an important basis to make decisions to sanction pollution acts. It is also the forecast information channel for ministries and agencies in development planning and devising strategies to minimize losses from the oil spill.

Zr-doped titania of anatase structure type has been prepared by a combined sol–gel and chemical vapour deposition (CVD) process. The material has been characterized by XRD, TEM and chemical analysis. The photocatalytic performance has been investigated in the oxidative decomposition of the pharmaceutical ibuprofen (IBP) down to low ppm concentrations. The change of the composition of the reaction solution after photocatalytic treatment was followed by UV–Vis spectroscopy and GC/MS. Formation of reaction intermediates was studied by HPLC coupled electrospray ionization time-of-flight mass spectrometry ESI-TOF-MS. The catalytic performance has been studied by varying the catalyst and substrate concentration as well as changing the catalyst-to-substrate ratio. The influence of pH, adsorption and re-use of the catalyst has been tested. The results confirm the high catalytic activity of Zr-doped titania compared to pure titania at low catalyst loading. The material shows the improved textural mesoporosity. However, more reaction intermediates were formed, leading to faster deactivation of the photocatalyst. ESI-TOF-MS measurements point to the formation of a couple of reaction intermediates, which poison the catalyst.

The preparation of nanoporous materials with enhanced stability using an improved synthesis route using reactive inorganic silica and alumina species is reported. This way improved mesoporous molecular sieves were obtained. The synthesized aluminum substituted mesoporous molecular materials (Al-MMS) contain very large pores of 50–200 A size combined with an improved pore wall thickness. Increased wall thickness and Al substitution lead to an improved chemical stability against alkaline solution. The textural, structural and acid properties are investigated by physico-chemical methods. The catalytic performance acidic materials was tested in the benzoylation reaction; amino functionalized materials were studied in the base catalyzed Michael addition.

Pulse width modulation strategies have been developed for indirect matrix converters (IMCs) in order to improve their performance. In indirect matrix converters, the LC input filter is used to remove input current harmonics and electromagnetic interference problems. Unfortunately, due to the existence of the input filter, the input power factor is diminished, especially during operation at low voltage outputs. In this paper, a new space vector modulation (SVM) is proposed to compensate for the input power factor of the indirect matrix converter. Both computer simulation and experimental studies through hardware implementation were performed to verify the effectiveness of the proposed modulation strategy.