Search

Titanium meshes are widely utilized in alveolar bone augmentation, and this study aims to enhance the properties of titanium meshes through heat treatment (HT) and the synergistic finishing technology of electric field and flow field (EFSF). Our findings illustrate that the titanium mesh exhibits improved mechanical properties following HT treatment. The innovative EFSF technique, in combination with HT, has a substantial impact on improving the surface properties of titanium meshes. HT initiates grain fusion and reduces surface pores, resulting in enhanced tensile and elongation properties. EFSF further enhances these improvements by significantly reducing surface roughness and eliminating adhered titanium powder, a byproduct of selective laser melting printing. Increased hydrophilicity and surface-free energy are achieved after EFSF treatment. Notably, the EFSF-treated titanium mesh exhibits reduced bacterial adhesion and is non-toxic to osteoblast proliferation. These advancements increase its suitability for clinical alveolar bone augmentation.

Large-size mandible graft has huge needs in clinic caused by infection, tumor, congenital deformity, bone trauma and so on. However, the reconstruction of large-size mandible defect is challenged due to its complex anatomical structure and large-range bone injury. The design and fabrication of porous implants with large segments and specific shapes matching the native mandible remain a considerable challenge. Herein, the 6% Mg-doped calcium silicate (CSi-Mg6) and β- and α-tricalcium phosphate (β-TCP, α-TCP) bioceramics were fabricated by digital light processing as the porous scaffolds of over 50% in porosity, while the titanium mesh was fabricated by selective laser melting. The mechanical tests showed that the initial flexible/compressive resistance of CSi-Mg6 scaffolds was markedly higher than that of β-TCP and α-TCP scaffolds. Cell experiments showed that these materials all had good biocompatibility, while CSi-Mg6 significantly promoted cell proliferation. In the rabbit critically sized mandible bone defects (∼13 mm in length) filled with porous bioceramic scaffolds, the titanium meshes and titanium nails were acted as fixation and load bearing. The results showed that the defects were kept during the observation period in the blank (control) group; in contrast, the osteogenic capability was significantly enhanced in the CSi-Mg6 and α-TCP groups in comparison with the β-TCP group, and these two groups not only had significantly increased new bone formation but also had thicker trabecular and smaller trabecular spacing. Besides, the CSi-Mg6 and α-TCP groups showed appreciable material biodegradation in the later stage (from 8 to 12 weeks) in comparison with the β-TCP scaffolds while the CSi-Mg6 group showed much outstanding mechanical capacity in vivo in the early stage compared to the β-TCP and α-TCP groups. Totally, these findings suggest that the combination of customized strength-strong bioactive CSi-Mg6 scaffolds together with titanium meshes is a promising way for repairing the large-size load-bearing mandible defects. [ABSTRACT FROM AUTHOR]

Featured Application: The proposed protocol, starting from a careful prediction of the final result with the ideal relationship between the prosthesis and soft tissues, aims to improve the GBR approach, particularly for critical atrophies.Background: Treating extended alveolar defects is challenging for their irregular shape and lack of hard and soft tissues. Virtual planned guided bone regeneration (GBR) with customized meshes aims to optimize the treatment by reducing the risk of dehiscence. The mucosa characteristics are crucial in preserving the bone graft covering and vitality. Methods: Two three-dimensional and extended defects, a mandibular posterior and anterior maxillary atrophy were reconstructed with a particulate graft and a digitally customized scaffold. The workflow entailed merging the pre-operatory clinical related data from intra-oral scanning with the radiologic ones from cone beam-CT. A final ideal prediction of the soft tissue relationship with the implant-borne prosthesis was virtually elaborated, conditioning the design of the titanium membrane fitting the bone defects. Results: A good matching between the scaffold and the bone surface was intra-operatory noted; no complications were registered in the first months of healing with complete integrity of the soft tissues above the graft. Conclusions: A careful evaluation of the soft tissues and a forecast of their final relationship with the implant and prosthesis can improve digital mesh/membrane manufacturing with a suitable healing process up to implant placement and loading, favoring peri-implant tissue stability over time. [ABSTRACT FROM AUTHOR]

Abstract Background One of the most recent innovations in bone augmentation surgery is represented by computer-aided-design/computer-aided-manufacturing (CAD/CAM) customized titanium meshes, which can be used to restore vertical bone defects before implant-prosthetic rehabilitations. The aim of this study was to evaluate the effectiveness/reliability of this technique in a consecutive series of cases. Methods Ten patients in need of bone augmentation before implant therapy were treated using CAD/CAM customized titanium meshes. A digital workflow was adopted to design virtual meshes on 3D bone models. Then, Direct Metal Laser Sintering (DMLS) technology was used to produce the titanium meshes, and vertical ridge augmentation was performed according to an established surgical protocol. Surgical complications, healing complications, vertical bone gain (VBG), planned bone volume (PBV), lacking bone volume (LBV), regenerated bone volume (RBV), average regeneration rate (RR) and implant success rate were evaluated. Results All augmented sites were successfully restored with definitive implant-supported fixed partial dentures. Measurements showed an average VBG of 4.5 ± 1.8 mm at surgical re-entry. Surgical and healing complications occurred in 30% and 10% of cases, respectively. Mean values of PBV, LBV, and RBV were 984, 92, and 892 mm3, respectively. The average RR achieved was 89%. All 26 implants were successfully in function after 1 year of follow-up. Conclusions The results of this study suggest that the bone augmentation by means of DMLS custom-made titanium meshes can be considered a reliable and effective technique in restoring vertical bone defects.

Background: Treating extended alveolar defects is challenging for their irregular shape and lack of hard and soft tissues. Virtual planned guided bone regeneration (GBR) with customized meshes aims to optimize the treatment by reducing the risk of dehiscence. The mucosa characteristics are crucial in preserving the bone graft covering and vitality. Methods: Two three-dimensional and extended defects, a mandibular posterior and anterior maxillary atrophy were reconstructed with a particulate graft and a digitally customized scaffold. The workflow entailed merging the pre-operatory clinical related data from intra-oral scanning with the radiologic ones from cone beam-CT. A final ideal prediction of the soft tissue relationship with the implant-borne prosthesis was virtually elaborated, conditioning the design of the titanium membrane fitting the bone defects. Results: A good matching between the scaffold and the bone surface was intra-operatory noted; no complications were registered in the first months of healing with complete integrity of the soft tissues above the graft. Conclusions: A careful evaluation of the soft tissues and a forecast of their final relationship with the implant and prosthesis can improve digital mesh/membrane manufacturing with a suitable healing process up to implant placement and loading, favoring peri-implant tissue stability over time.

Bone augmentation procedures represent a real clinical challenge. One option is the use of titanium meshes. Additive manufacturing techniques can provide custom-made devices in titanium alloy. The purpose of this study was to investigate the material used, which can influence the outcomes of the bone augmentation procedure. Specific test samples were obtained from two different manufacturers with two different shapes: surfaces without perforations and with calibrated perforations. Three-point bending tests were run as well as internal friction tests to verify the Young's modulus. Test samples were placed in two different buffered solutions and analyzed with optical microscopy. A further SEM analysis was done to observe any microstructural modification. Three-point flexural tests were conducted on 12 specimens. Initial bending was observed at lower applied stresses for the perforated samples (503 MPa) compared to non-perforated ones (900 MPa); the ultimate flexural strength was registered at 513 MPa and 1145 MPa for perforated and non-perforated samples, respectively. Both microscopic analyses (optical and SEM) showed no significant alterations. Conclusions: A normal masticatory load cannot modify the device. Chemical action in the case of exposure does not create macroscopic and microscopic alterations of the surface. [ABSTRACT FROM AUTHOR]

Background: One of the most recent innovations in bone augmentation surgery is represented by computer-aided-design/computer-aided-manufacturing (CAD/CAM) customized titanium meshes, which can be used to restore vertical bone defects before implant-prosthetic rehabilitations. The aim of this study was to evaluate the effectiveness/reliability of this technique in a consecutive series of cases. Methods: Ten patients in need of bone augmentation before implant therapy were treated using CAD/CAM customized titanium meshes. A digital workflow was adopted to design virtual meshes on 3D bone models. Then, Direct Metal Laser Sintering (DMLS) technology was used to produce the titanium meshes, and vertical ridge augmentation was performed according to an established surgical protocol. Surgical complications, healing complications, vertical bone gain (VBG), planned bone volume (PBV), lacking bone volume (LBV), regenerated bone volume (RBV), average regeneration rate (RR) and implant success rate were evaluated. Results: All augmented sites were successfully restored with definitive implant-supported fixed partial dentures. Measurements showed an average VBG of 4.5 ± 1.8 mm at surgical re-entry. Surgical and healing complications occurred in 30% and 10% of cases, respectively. Mean values of PBV, LBV, and RBV were 984, 92, and 892 mm3, respectively. The average RR achieved was 89%. All 26 implants were successfully in function after 1 year of follow-up. Conclusions: The results of this study suggest that the bone augmentation by means of DMLS custom-made titanium meshes can be considered a reliable and effective technique in restoring vertical bone defects. [ABSTRACT FROM AUTHOR]

Bone augmentation procedures represent a real clinical challenge. One option is the use of titanium meshes. Additive manufacturing techniques can provide custom-made devices in titanium alloy. The purpose of this study was to investigate the material used, which can influence the outcomes of the bone augmentation procedure. Specific test samples were obtained from two different manufacturers with two different shapes: surfaces without perforations and with calibrated perforations. Three-point bending tests were run as well as internal friction tests to verify the Young’s modulus. Test samples were placed in two different buffered solutions and analyzed with optical microscopy. A further SEM analysis was done to observe any microstructural modification. Three-point flexural tests were conducted on 12 specimens. Initial bending was observed at lower applied stresses for the perforated samples (503 MPa) compared to non-perforated ones (900 MPa); the ultimate flexural strength was registered at 513 MPa and 1145 MPa for perforated and non-perforated samples, respectively. Both microscopic analyses (optical and SEM) showed no significant alterations. Conclusions: A normal masticatory load cannot modify the device. Chemical action in the case of exposure does not create macroscopic and microscopic alterations of the surface.

Objective. To analyze the results of using titanium meshes for anterior fusion in spinal reconstruction in pediatric patients. Material and Methods. Design: A retrospective cohort study from 2011 to 2014. Spinal reconstruction in 108 patients aged 8 months to 17 years was performed with titanium meshes filled with bone autografts. The indications for surgery were Pott’s disease (n = 41), non-specific chronic spondylitis and its sequences (n = 42), spinal tumors (n = 11) and congenital spinal deformities (n = 6). Additional posterior instrumentation was carried out in case of multilevel spinal reconstruction or for spinal deformity. Clinical and radiological FU results were evaluated at the 6, 12, 18 months after surgery with the analy- sis of infection reactivation risk, changes in the apical Cobb angle and dynamics of block formation in anterior fusion zone. Results. No cases of infection reactivation or process aggravation were detected during 6 months after surgery. Two pa- tients (with TB spondylitis and giant cell tumor) had deterioration of vertebral destruction with mesh instability in the period from 6 to 12 months after surgery. No one case of mesh stability preservation was associated with deformity pro- gression. Solid bone block was formed in 97 % of operated patients at 12 months after surgery. Conclusion. Using of meshes in reconstructive surgery on the spine in children does not increase the rate of postoperative complications even in infectious spondylitis, due to biological inertia of the non-resorbable material.

Titanium meshes are widely utilized in alveolar bone augmentation, and this study aims to enhance the properties of titanium meshes through heat treatment (HT) and the synergistic finishing technology of electric field and flow field (EFSF). Our findings illustrate that the titanium mesh exhibits improved mechanical properties following HT treatment. The innovative EFSF technique, in combination with HT, has a substantial impact on improving the surface properties of titanium meshes. HT initiates grain fusion and reduces surface pores, resulting in enhanced tensile and elongation properties. EFSF further enhances these improvements by significantly reducing surface roughness and eliminating adhered titanium powder, a byproduct of selective laser melting printing. Increased hydrophilicity and surface-free energy are achieved after EFSF treatment. Notably, the EFSF-treated titanium mesh exhibits reduced bacterial adhesion and is non-toxic to osteoblast proliferation. These advancements increase its suitability for clinical alveolar bone augmentation., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest., (Copyright © 2023 Wang, Wang, Ayisen, Ren, Luo and Wang.)