Search

This paper presents an original concept in which integrated over-voltage and/or over-current protections of power devices are used to produce a self-switching operation. Such a commutation is shown as a possible combination with conventional forced-switching and spontaneous-switching to simplify direct regenerative ac-dc conversion, insulating dc-ac-dc conversion and finally direct ac-ac conversion. Experimental results prove the feasibility of the concept through which the self turn-off operation is likely to offer the best practical gains. Index Terms--Direct ac-ac pulsewidth modulation (PWM) conversion, isolated dc-dc conversion, regenerative ac-dc conversion, self-switching, self turn-off, self turn-on.

The power characteristics of wind turbines are nonlinear. It is particularly true for vertical-axis turbines whose provided power is very sensitive to the load. Thus, controlling the operating point is essential to optimize the energetic behavior. Several control strategies (maximum power point tracking) can be used for the energy conversion. If the wind-turbine characteristic [C.sub.p] ([lambda]) is supposed to be a priori known, it can be used for optimal control of the torque, speed, or system output power. On the contrary, if this characteristic is unknown, an operational seeking algorithm such as fuzzy logic has to be implemented. Several structures with different associated complexity degrees can be used, in particular, the structure of the ac--dc conversion, which can be either a pulsewidth-modulation voltage-source rectifier or a simple diode bridge. A comparative study of the corresponding control strategies and architectures is proposed in this paper regarding the tradeoffs between structure complexity and energy efficiency. The analysis is based on simulations and experiments. Index Terms--Architecture, efficiency, renewable energy, wind-power generation.

The test and the characterization of medium or high-power electronic converters, under nominal operating conditions, are made difficult by the requirement of high-power electrical source and load. In addition, the energy lost during the test may be very significant. The opposition method, which consists of an association of two identical converters supplied by the same source, one operating as a generator, the other as a receptor, can be a better way to do these test. Another advantage is the possibility to realize accurate measurements of the different losses in the converters under test. In the first part of this paper, the characteristics of the method concerning loss measurements are compared to those of the electrical or calorimetric methods, then it is shown how it can be applied to different types of power electronic converters, choppers, switched mode power supplies, and pulsewidth modulation inverters. In the second part, different examples of studies conducted by the authors, and using this method, are presented. They have varying goals, from the test of soft-switching inverters to the characterization of integrated gate-commutated thyristor (IGCT) devices mounted into 2-MW choppers. Index Terms--Integrated gate-commutated thyristor (IGCT) characterizations, inverter losses measurement, opposition method, reliability test in power electronics.

Power-factor-corrector (PFC) converters are now commonly used in low-power supply systems connected to ac networks. In addition to their basic PFC properties, they constitute the best technical solution to directly obtain the compatibility with a large range of ac voltages provided by different distribution networks around the world (typically, from 85 to 265 V rms). It is the main application of these converters. This function is achieved with an additional cost and volume, and this extra price to pay needs to be minimized. In this context, we first recall the main approaches of the design of conventional PFCs based on the boost converter topology. We emphasize the different critical points of the sizing that mainly concern the input choke and the silicon devices, in regard with the choice of the switching frequency. Few ways of improvement are then presented for these conventional PFCs. In a second part, always in the context of a large input voltage range, we consider the possibility to introduce the multi-level concept to reduce the input choke and filters. A solution using a multilevel Flying Capacitor Two-Cell converter is presented. It is shown that it can lead to a significant increase of the performances, with several options of sizing which can be suited to different requirements of the applications. Index Terms--Flying capacitor multicell converter, flying capacitors, multilevel converter, power-factor corrector (PFC).

The auxiliary resonant commutated pole (ARCP) multiceLl converter is a soft-switched variant of the multicell converter. It is shown in this paper that the ARCP technique can be very efficiently used in multicell flying capacitor converters. The main properties of the resulting soft switching multicell converter are very similar to those of the hard-switched version. They are presented and validated by simulations as well as experimental results. In practice, due to the damping, the ARCP multicell converter can suffer from switching faults as in two-level ARCP inverters, but in the case of a multicell converter failures can occur in different cells. So, the main control strategies are evaluated and the switching process is discussed step by step, taking account of the main imperfections of actual control circuits. When they can occur, the switching faults are described and analyzed. Finally, an original quasisoft switching control that should give a high safety of operation is proposed. Experimental results obtained with a 900 V-100 A ARCP multicell inverter leg are given and the performances are compared with those of a hard-switched multicell inverter leg of the same rating. Index Terms--ARCP, dual-thyristor, multicell flying capacitor inverter, safe control, soft-switching, switching faults.

The aim of this paper is to explain the intrinsic short-circuit tolerance of an IGBT multicell inverter when a commutation failure occurs. Such a failure may either be a wrong gate voltage (malfunctioning of the driver board, auxiliary power supply failure, dv / dt disturbance) or an intrinsic IGBT failure (over-voltage/avalanche stress, temperature overshoot). IGBT stresses are studied and show that no opening of the bonding can appear and consequently no risk of explosion. That is why, owing to the imbricated cells structure, an IGBT short-circuit failure may be withstood for a few switching periods, with nevertheless nonoptimized output waveforms. The design, the lab-test of a sensor able to perform monitoring as well as the failure diagnosis are also presented. This real-time diagnosis allows either a safe stop or a remedial control strategy based on the reconfiguration of the PWM modulator. The reconfiguration strategy enables decrease internal stresses and optimize the output shape. A fail-safe operating may be gained for high power applications. Index Terms--Fail-safe operation, faults, multicell converters, multilevel converters, redundancy.

The imbricated-cell multilevel converter is well suited to high power applications. It allows the series connection of n switches with natural voltage sharing between these switches enabled through the connection of n - 1 flying capacitors. This paper deals with the application of soft-switching on this topology; to date, only the hard-switching mode has been studied. The use of soft switching enables an increase of the switching frequency (resulting in the size reduction of the flying capacitors) without a decrease of the converter efficiency. Of the soft switching methods considered, the Auxiliary Resonant Commutated Pole (ARCP) technique was chosen due to the relative ease in which it can be incorporated into the converter topology. Furthermore, this technique offers numerous advantages: loss reduction, no added stress to the switches and compatibility with PWM control. The main properties of the ARCP multicell converter are the same as the hard-switched topology: an increase of the apparent output switching frequency and natural self-balancing of the flying-capacitor voltages. This paper presents the results of both simulations performed and measurements taken from an experimental set-up in order to study the viable system functioning. The introduction of soft-switching strongly complicates the theoretical study of the balancing mechanisms, however. As a result, the authors depend on simulations to validate the natural balancing effect during soft switching. Lastly, a general method of loss measurement is presented. Results show that the converter losses are reduced by at least 30%. Index Terms--ARCP, multicell converter, opposition method, soft switching, ZVS.

Multicell converters were introduced ten years ago and, over this period, their properties have been thoroughly analyzed. Since then, this concept has lead to some other innovative topologies which are briefly presented in this paper. Different ways to introduce soft switching in multicell converters are investigated. The concept of distributing power over several switches, giving more degrees of freedom and using less passive components, is extended further with the stacked multiceli topology. Finally, direct ac-ac converters using the multicell approach are described. Index Terms--AC-AC power conversion, insulated gate bipolar transistors, multilevel systems, power electronics, power systems harmonics, resonant power conversion, variable-speed drives.

Component counts and oversimplified reliability rules may lead to the conclusion that multilevel converters are less safe than two-level converters, just because they use more components. A better approach might be to consider that they use a different arrangement of components and also that the consequence of faults may be very different. This paper is focused on the study of the consequences of faults in hard-switching and soft-switching multicell converters. Solutions to minimize the consequences of major faults are described. Index Terms--Fault currents, fault detection, fault location, fault tolerance, insulated gate bipolar transistors, multilevel systems, power electronics, power systems harmonics.

This article shows both theoretical and experimental analyses of a fully integrated CMOS active gate driver (AGD) developed to control the high dv/dt of GaN transistors for both 48 and 400 V applications. To mitigate negative effects in the high-frequency spectrum emission, an original technique is proposed to reduce the dv/dt with lower switching losses compared to classical solutions. The AGD technique is based on a subnanosecond delay feedback loop, which reduces the gate current only during the dv/dt sequence of the switching transients. Hence, the dv/dt and di/dt can be actively controlled separately, and the tradeoff between the dv/dt and EON switching energy is optimized. Since GaN transistors have typical voltage switching times on the order of a few nanoseconds, introducing a feedback loop from the high voltage drain to the gate terminal is quite challenging. In this article, we successfully demonstrate the active gate driving of GaN transistors for both 48 and 400 V applications, with initial open-loop voltage switching times of 3 ns, due to a full CMOS integration. Other methods for dv/dt active control are further discussed. The limits of these methods are explained based on both experimental and simulation results. The AGD showed a clear reduction in the peak dv/dt from –175 to –120 V/ns for the 400 V application. [ABSTRACT FROM AUTHOR]