Search

Carbon xerogels (CXs) were synthesized by polycondensation of resorcinol and formaldehyde, followed by thermal annealing, and subjected to hydrothermal oxidation. Solid-phase extraction (SPE) cartridges were filled with CXs and tested for extraction of metaflumizone and other seven environmental micropollutants (acetamiprid, atrazine, isoproturon, methiocarb, carbamazepine, diclofenac, and perfluorooctanesulfonic acid) before chromatographic analysis. The recoveries obtained with the pristine CX were low for most analytes, except for metaflumizone (69 ± 5%). Moreover, it was concluded that the adsorption/desorption process of the micropollutants performed better on CXs with a less acidic surface (i.e., pristine CX). Thus, cartridges were prepared with pristine CX and multi-walled carbon nanotubes (MWCNTs) in a multi-layer configuration. This reusable cartridge was able to simultaneously extract the eight micropollutants and was used to validate an analytical methodology based on SPE followed by ultra-high performance liquid chromatography-tandem mass spectrometry. A widespread occurrence of 6/8 target compounds was observed in surface water collected in rivers supplying three drinking water treatment plants and in the resulting drinking water at the endpoint of each distribution system. Therefore, the first study employing CXs and MWCNTs as sorbent in multi-layer SPE cartridges is herein reported as a proof of concept for determination of multi-class water micropollutants. [ABSTRACT FROM AUTHOR]

Graphical abstract Highlights • The influence of water matrix on the efficiency of AOTs is overviewed. • Photolysis, photocatalysis, UV/H 2 O 2 -, Fenton-, and O 3 -based processes are reviewed. • Dissolved organic matter and inorganics can act as inhibitors and/or promoters. • The effect results from the interplay of the co-existing substances. • The knowledge on the role of matrix constituents is crucial for installation of AOTs. Abstract Micropollutants (MPs) in the aquatic compartments are originated from many sources and particularly from the effluents of urban wastewater treatment plants (UWWTPs). Advanced oxidation technologies (AOTs) usually applied after biological processes, have recently emerged as effective tertiary treatments for the removal of MPs, but the oxidation rates of the single compounds may be largely affected by the constituent species of the water matrix. These species include dissolved organic matter and inorganic species (e.g., carbonate, bicarbonate, nitrite, sulphate, chloride). This review analyses the impact of such substances on common AOTs including photolysis, UV/H 2 O 2 , Fenton, photocatalysis, and ozone-based processes. The degradation efficiency of single MPs by AOTs results from the combined impact of the water matrix constituents, which can have neutral, inhibiting or promoting effect, depending on the process and the mechanism by which these water components react. Organic species can be either inhibitors (by light attenuation; scavenging effects; or adsorption to catalyst) or promoters (by originating reactive oxygen species (ROS) which enhance indirect photolysis; or by regenerating the catalyst). Inorganic species can also be either inhibitors (by scavenging effects; formation of radicals less active than hydroxyl radicals; iron complexation; adsorption to catalyst or decrease of its effective surface area) or promoters (e.g., nitrate ions by formation of ROS; iron ions as additional source of catalyst). The available data reviewed here is limited and the role and mechanisms of individual water components are still not completely understood. Further studies are needed to elucidate the wide spectrum of reactions occurring in complex wastewaters and to increase the adoption of AOTs in UWWTPs. [ABSTRACT FROM AUTHOR]

Abstract The presence of organic micropollutants (MPs) in the aquatic environment is strongly related to their difficult elimination by conventional water and wastewater treatment processes. Therefore, alternative treatment technologies are required to overcome this problem. In this domain, constructed wetlands (CWs) have gained increasing attention in the last years, mainly due to the low-cost, simple operation/maintenance and environmental friendliness of these systems. However, studies on the application of CWs to remove MPs from freshwater aquaculture effluents are still scarce. In this work, planted (Phragmites australis) vertical subsurface flow CWs, at microcosm scale, were investigated for the removal of MPs found in non-spiked freshwater aquaculture effluents, namely atrazine, isoproturon, perfluorooctanesulfonic acid (PFOS), clarithromycin, erythromycin, fluoxetine, norfluoxetine, and 2-ethylhexyl-4-methoxycinnamate (EHMC). A wider multi-component set of 36 MPs was also studied by adding these MPs at 100 ng L−1 to the same matrix (alachlor, atrazine, chlorfenvinphos, isoproturon, PFOS, azithromycin, clarithromycin, erythromycin, diclofenac, methiocarb, acetamiprid, clothianidin, thiacloprid, thiamethoxam, EHMC, simazine, atorvastatin, bezafibrate, carbamazepine, cephalexin, ceftiofur, citalopram, clindamycin, clofibric acid, diphenhydramine, enrofloxacin, fluoxetine, ketoprofen, metoprolol, norfluoxetine, ofloxacin, propranolol, tramadol, trimethoprim, venlafaxine, and warfarin). High weekly removal efficiencies (>87%) were observed for all MPs in both non-spiked and spiked experiments, with the exception of EHMC (removal rates between 0 and 86%). These results emphasize the potential of CWs to remove MPs from freshwater aquaculture effluents, but also the need to enhance the performance of these systems for the elimination of some recalcitrant MPs, such as EHMC, which was found at high concentrations in the studied effluents. Graphical abstract Unlabelled Image Highlights • Constructed wetland microcosms studied for the removal of organic micropollutants. • Spiked (36 micropollutants) and non-spiked aquaculture effluents were investigated. • Most micropollutants found in effluents were removed to below the detection limit. • Weekly removal efficiencies were higher than 87% for most spiked micropollutants. • The UV filter EHMC was the only recalcitrant micropollutant. [ABSTRACT FROM AUTHOR]

Abstract The European Union (EU) has recommended the monitoring of specific priority substances (PSs, Directive 2013/39) and some contaminants of emerging concern (CECs, Decision 2015/495) in surface waterbodies. The present study provides spatial distributions and temporal variations of a wide range of multi-class PSs and CECs in four stressed rivers in Portugal (Ave, Leça, Antuã, and Cértima). Thirteen micropollutants were found in all four rivers, including the priority pesticide isoproturon (up to 92 ng L−1), various pharmaceuticals (up to 396 ng L−1), and the UV-filter 2-ethyl-hexyl-4-methoxycinnamate (EHMC, up to 562 ng L−1) identified in Decision 2015/495. The industrial priority compound perfluorooctanesulfonic acid (PFOS) was found in three rivers (Antuã, Cértima, and Leça) below the method quantification limit, together with four pharmaceuticals not included in these EU guidelines. The already banned priority pesticide atrazine was detected in Ave, Antuã, and Leça (up to 41 ng L−1) and simazine in Cértima and Leça (up to 26 ng L−1). Acetamiprid and imidacloprid (included in Decision 2015/495) were only detected during the dry season in the Ave. Leça river was selected as a waterbody case study for assessment of fluorescence excitation-emission matrices (EEMs). These results matched the spatial distribution trend of micropollutants along the river, with stronger fluorescence response and higher concentrations being found downstream of industrial areas and urban wastewater treatment plants (WWTPs). Moreover, the fluorescence signature of surface water collected downstream of an urban WWTP aligned very well with that obtained for the respective WWTP effluent. Thus, actions are needed to preserve a good environmental status of these stressed European waterbodies. Graphical abstract Unlabelled Image Highlights • Spatial and seasonal variations of multi-class micropollutants were studied. • Four stressed rivers in Portugal were monitored in dry and wet seasons. • Ketoprofen, tramadol, enrofloxacin and thiacloprid were measured at highest levels. • The fluorescence EEMs of surface water matched the distribution of micropollutants. • Correlation of fluorescence signatures found for azithromycin, carbamazepine, EHMC. [ABSTRACT FROM AUTHOR]

The contamination of fresh water is a global concern. The huge impact of natural and anthropogenic organic substances that are constantly released into the environment, demands a better knowledge of the chemical status of Earth’s surface water. Water quality monitoring studies have been performed targeting different substances and/or classes of substances, in different regions of the world, using different types of sampling strategies and campaigns. This review article aims to gather the available dispersed information regarding the occurrence of priority substances (PSs) and contaminants of emerging concern (CECs) that must be monitored in Europe in surface water, according to the European Union Directive 2013/39/EU and the Watch List of Decision 2015/495/EU, respectively. Other specific organic pollutants not considered in these EU documents as substances of high concern, but with reported elevated frequency of detection at high concentrations, are also discussed. The search comprised worldwide publications from 2012, considering at least one of the following criteria: 4 sampling campaigns per year, wet and dry seasons, temporal and/or spatial monitoring of surface (river, estuarine, lake and/or coastal waters) and ground waters. The highest concentrations were found for: (i) the PSs atrazine, alachlor, trifluralin, heptachlor, hexachlorocyclohexane, polycyclic aromatic hydrocarbons and di(2-ethylhexyl)phthalate; (ii) the CECs azithromycin, clarithromycin, erythromycin, diclofenac, 17α-ethinylestradiol, imidacloprid and 2-ethylhexyl 4-methoxycinnamate; and (iii) other unregulated organic compounds (caffeine, naproxen, metolachlor, estriol, dimethoate, terbuthylazine, acetaminophen, ibuprofen, trimethoprim, ciprofloxacin, ketoprofen, atenolol, Bisphenol A, metoprolol, carbofuran, malathion, sulfamethoxazole, carbamazepine and ofloxacin). Most frequent substances as well as those found at highest concentrations in different seasons and regions, together with available risk assessment data, may be useful to identify possible future PS candidates. [ABSTRACT FROM AUTHOR]

The presence of organic pollutants in the aquatic environment, usually found at trace concentrations (i.e., between ng L −1 and μg L −1 or even lower, known as micropollutants), has been highlighted in recent decades as a worldwide environmental concern due to their difficult elimination by conventional water and wastewater treatment processes. The relevant information on constructed wetlands (CWs) and their application for the removal of a specific group of pollutants, 41 organic priority substances/classes of substances (PSs) and 8 certain other substances with environmental quality standards (EQS) listed in Directive 2013/39/EU as well as 17 contaminants of emerging concern (CECs) of the Watch List of Decision 2015/495/EU, is herein reviewed. Studies were found for 24 PSs and 2 other substances with EQS: octylphenol, nonylphenol, perfluorooctane sulfonic acid, di(2-ethylhexyl)phthalate, trichloromethane, dichloromethane, 1,2-dichloroethane, pentachlorobenzene, benzene, polychlorinated dibenzo-p-dioxins, naphthalene, fluoranthene, trifluralin, alachlor, isoproturon, diuron, tributyltin compounds, simazine, atrazine, chlorpyrifos (chlorpyrifos-ethyl), chlorfenvinphos, hexachlorobenzene, pentachlorophenol, endosulfan, dichlorodiphenyltrichloroethane (or DDT) and dieldrin. A few reports were also published for 8 CECs: imidacloprid, erythromycin, clarithromycin, azithromycin, diclofenac, estrone, 17-beta-estradiol and 17-alpha-ethinylestradiol. No references were found for the other 17 PSs, 6 certain other substances with EQS and 9 CECs listed in EU legislation. [ABSTRACT FROM AUTHOR]

The fate and removal of organic micropollutants in the environment is a demanding issue evidenced by the recent European policy. This work presents an analytical method for the trace quantification of 37 micropollutants including Priority Substances (Directive 2013/39/EU), substances of the recent watch list (Decision 2015/495/EU) and contaminants of emerging concern: pesticides, multi-class pharmaceuticals and a metabolite, estrogens and one industrial compound. The analytical method was based on solid phase extraction (SPE) followed by ultra-high performance liquid chromatography with tandem mass spectrometry (UHPLC–MS/MS), using eco-friendly solvents (ethanol and ultrapure water) both in the SPE and UHPLC, according to green analytical chemistry principles. Briefly, Oasis ® HLB cartridges were used to preconcentrate 100 mL of water samples and the reconstituted extracts were analyzed with a Kinetex™ column under reversed mode, the linear ranges extended to 200 ng L −1 ( R 2 > 0.99) for all the analytes. The method detection limits were between 0.04 and 2.26 ng L −1 and the method quantification limits were between 0.13 and 6.85 ng L −1 . The identity of the compounds was confirmed using two MS/MS transitions and its ion ratios, according to Decision 2002/657/EC. The validated method was applied to wastewater treatment plant samples, assessing the concentration of micropollutants after secondary biological and tertiary UV treatments. Lab-scale photolysis and ozonation experiments were also performed with the secondary effluents, with ozonation showing the best performance for the removal of most of the determined micropollutants. [ABSTRACT FROM AUTHOR]

Silica@polymer spheres with a core@shell structure were synthesized and thermally annealed at 800 ºC to obtain silica@carbon spheres (SiO 2 @CSs). The silica core was removed by etching with NaOH, hollow carbon spheres (CSs) being obtained. The particle size of SiO 2 @CSs and CSs increased with the ethanol/water (E/W) volumetric ratio (2, 4.5, and 7) employed in the first synthesis step (i.e. , the Stöber's method to obtain silica particles). Moreover, the average diameter of the materials prepared with E/W ratio of 2 was affected by the etching of the SiO 2 core (from 168 to 109 nm), in contrast with those synthesized at higher E/W ratios of 4.5 and 7 (251–245 and 270–284 nm, respectively). The specific surface area (S BET) of the CSs ranged from 271 to 602 m2 g−1, which are more porous than SiO 2 @CSs (S BET in the range 115–144 m2 g−1). Adsorption kinetic and equilibrium studies were carried out with diclofenac and venlafaxine as model organic micropollutants (OMPs). Despite the silica removal was not effective for all the CSs (TGA residue ranging from 3 to 46 wt%), the kinetic studies and the ATR-FTIR spectra confirmed the positive effect of having a hollow core (i.e. , removing the silica core). Equilibrium studies demonstrated that CSs prepared with an E/W ratio of 7 were the best performing material when considering both OMPs. Moreover, these CSs performed well to remove a set of 24 OMPs from wastewater effluents and thus, they are an interesting option for water or wastewater treatment. [Display omitted] • Nanostructured hollow carbon spheres (CSs) with different sizes synthesized. • First study employing CSs for the adsorption of diclofenac and venlafaxine (VFX). • Beneficial role of the hollow core within the CSs was demonstrated. • Best performance in equilibrium tests with the CSs having larger particle size. • Highest VFX adsorption capacity (61.45 mg g-1) among reported carbon materials. [ABSTRACT FROM AUTHOR]

Aquaculture is the fastest growing animal food-producing sector. Water is the central resource for aquaculture, and it is essential that its quality be preserved. Micropollutants (MPs) can reach aquaculture through anthropogenic addition or inlet water, and may cause harmful effects such as endocrine disruption and antibiotic resistance, adversely affecting the fish species being farmed. Furthermore, the discharge of aquaculture effluents into the environment may contribute to the deterioration of water courses. In this sense, the implementation of environmentally responsible measures in aquaculture farms is imperative for the protection of ecosystems and human health. The European Commission (EC) has recently launched a guiding document promoting ecological aquaculture practices; however, options for water treatment are still lacking. Conventional processes are not designed to deal with MPs; this review article consolidates relevant information on the application of advanced oxidation technologies (AOTs) and constructed wetlands (CWs) as potential strategies in this regard. Although 161 studies on the application of AOTs or CWs in aquaculture have already been published, only 34 focused on MPs (28 on AOTs and 6 on CWs), whereas the others reported the removal of contaminants such as bacteria, organic matter, solids and inorganic ions. No study coupling both treatments has been reported to date for the removal of MPs from aquaculture waters. AOTs and CWs are prospective alternatives for the treatment of aquacultural aqueous matrices. However, the type of aquaculture activity and the specifications of these available technologies should be considered while selecting the most suitable treatment option. [Display omitted] • Micropollutants in aquaculture water is a concern of the European Commission. • Chemical and biological treatments to remove these micropollutants are reviewed. • Studies with real matrices are scarce for advanced oxidation technologies (AOTs). • More studies conducted at full scale are needed for constructed wetlands (CWs). • Both AOTs and CWs can remove conventional pollutants from aquaculture waters. [ABSTRACT FROM AUTHOR]

Ozone-based water treatments were investigated to simultaneously remove organic micropollutants (OMPs) and bacteria from surface water samples collected in a river reservoir supplying a drinking water treatment plant. Among the 21 environmentally relevant OMPs selected, 15 were detected at low (< 20) ng L−1 level. Surface water samples were then spiked with these 21 OMPs (100 ng L−1) and the ozone-based treatments were tested with excess of ozone and high hydraulic retention time (HRT: 41 min). Regardless of the treatment applied (O 3 , O 3 /UVA-LEDs, and O 3 /H 2 O 2), removal efficiencies higher than 85% were always obtained for 20 out of 21 OMPs (and lower than 50% for PFOS). Thus, single ozonation was considered the best treatment solution, being afterwards investigated in terms of water disinfection at milder operating conditions (3 mg O 3 L−1 and HRT: 10 min). Under these conditions, the removals of spiked OMPs were also higher than 85% (except for PFOS), whereas bacteria (i.e. , total heterotrophs at 37 and 22 °C, E. coli and enterococci) decreased to values lower than the permissible levels for drinking water, even upon storage for 3-days. However, lower ozone doses (1.5 mg O 3 L−1) could not prevent the regrowth of total heterotrophs incubated at 37 °C, which reached levels five times higher than those recommended. Because drinking water treatments should not only consider OMPs abatement but also microbial inactivation for long periods of time, the results herein obtained point out the importance of using ozone doses capable of accomplish both targets when using single ozonation. [Display omitted] • Ozone-based treatments investigated for surface water intended for consumption. • 20 out of 21 organic micropollutants were removed (>85%) by single ozonation. • PFOS removals were lower than 50% regardless of the treatment process tested. • The treated water had sufficient microbial quality for human consumption. • Ozone doses lower than 3 mg O 3 L−1 are not recommended due to bacteria regrowth. [ABSTRACT FROM AUTHOR]

• DCF and MET are degraded efficiently under visible light, using g-C 3 N 4. • In real water matrices, DCF and MET undergo by indirect photolysis. • DCF had a competitive impact on the removal of MET. • MET had only a slight impact on the degradation of DCF. • Radical and holes play an essential role in the degradation of DCF and MET. In this work, graphite-like carbon nitride (CN) materials were activated with 417 nm light from a LED device for the photocatalytic decomposition of commonly prescribed pharmaceuticals that are recurrent as organic micropollutants (MPs) in environmental waters. The decomposition resistance of diclofenac (DCF) and metoprolol (MET) was investigated by spiking these MPs in different water matrices: ultrapure water, river water, and wastewater. The photochemical stability of both MPs, each constituent ionic species' impact, and the MPs' competitive effect during the photocatalytic treatment were investigated. The target MPs had some photochemical instability under visible light in real water samples, suggesting that the organic matter present on it may act as a photosensitizer and promote these MPs' photodegradation. Besides, competition between the MPs was verified. A noteworthy decrease in the MET kinetic constants was observed when DCF was co-occurring in solution, independently of the water matrix and the initial concentration of the competing MP. By trapping photogenerated holes and radicals with selective scavengers, we found that different ratios of the reactive species are generated during the photocatalytic process, which relies on the presence of each or both MPs. [ABSTRACT FROM AUTHOR]

Ozonation followed by ultrafiltration (O3 + UF) was employed at pilot scale for the treatment of secondary urban wastewater, envisaging its safe reuse for crop irrigation. Chemical contaminants of emerging concern (CECs) and priority substances (PSs), microbial load, estrogenic activity, cell viability and cellular metabolic activity were measured before and immediately after O3 + UF treatment. The microbial load was also evaluated after one-week storage of the treated water to assess potential bacteria regrowth. Among the organic micropollutants detected, only citalopram and isoproturon were not removed below the limit of quantification. The treatment was also effective in the reduction in the bacterial loads considering current legislation in water quality for irrigation (i.e., in terms of enterobacteria and nematode eggs). However, after seven days of storage, total heterotrophs regrew to levels close to the initial, with the concomitant increase in the genes 16S rRNA and intI1. The assessment of biological effects revealed similar water quality before and after treatment, meaning that O3 + UF did not produce detectable toxic by-products. Thus, the findings of this study indicate that the wastewater treated with this technology comply with the water quality standards for irrigation, even when stored up to one week, although improvements must be made to minimise microbial overgrowth. [ABSTRACT FROM AUTHOR]

Numerous contaminants of emerging concern (CECs) have been found in different water bodies. Directive 2013/39/EU and Decision 2018/840/EU are consequently being implemented in the field of water policies. Twelve CECs (e.g., isoproturon, ciprofloxacin, and clarithromycin are among those listed) were detected in a municipal wastewater secondary effluent by means of solid phase extraction and ultra-high-performance liquid chromatography with tandem mass spectrometry (SPE-UHPLC-MS/MS). Different advanced oxidation processes (AOPs), based on the combination of ozone, UVA-LED and powdered TiO2, were investigated for their removal in a semi-batch operation. In addition, TiO2-coated glass rings (P25R) were characterized with different techniques (SEM, WDXRF) and used for continuous mode operation in a packed bed reactor (PBR). Among the AOPs studied, ozone-based processes were found to be more efficient than heterogeneous photocatalysis. A kinetic study was performed showing that direct ozonation is the main oxidation pathway for CEC removal. Ozone was successfully decomposed in combination with UVA-LED and P25R, resulting in an apparent rate constant of 3.2 × 10−2 s−1 higher than in the O3/LED system (1.0 × 10−3 s−1) or with ozone alone (8.6 × 10−5 s−1). Hydroxyl radical reaction could prevail over direct ozone reaction for the most refractory compounds (e.g., isoproturon). [ABSTRACT FROM AUTHOR]

• Municipal wastewater (MWW) was treated by advanced oxidation technologies (AOTs). • Direct contact membrane distillation (DCMD) was investigated as post-treatment. • Ozonation was efficient to remove 12 micropollutants (MPs) determined in MWW. • UV/H 2 O 2 as pre-treatment minimized the flux decline. • Flux decline was strongly related to the DOC content of the DCMD feed. In this work, the combination of advanced oxidation technologies (AOTs) and direct contact membrane distillation (DCMD) was investigated for the treatment of municipal wastewater collected from the secondary clarifier of a municipal wastewater treatment plant (MWWTP). Average removal efficiencies of the 12 micropollutants present in the wastewater samples were higher than 95 % with ozonation (O 3) and photolytic ozonation (UV/O 3), whereas only near 50 % of removal efficiency was achieved with UV-peroxidation (UV/H 2 O 2). When the ozone-based processes were combined with DCMD, the concentration of these micropollutants were below the detection limits in the respective permeate, increasing the quality of the treated water. However, the permeate fluxes in DCMD were remarkably higher when the wastewater was pre-treated with UV/H 2 O 2 instead of O 3 , most probably due to the better disinfection achieved by UV/H 2 O 2. It was also confirmed that the dissolved organic carbon (DOC) of the wastewater strongly affects the permeate fluxes achieved by DCMD. In this regard, the combination of the oxidation and membrane separation processes is more appropriate for wastewaters with low DOC contents (< 15 mg L−1). [ABSTRACT FROM AUTHOR]

Graphical abstract Highlights • Exfoliated graphitic carbon nitride (g-C 3 N 4) was synthesised and characterized. • The metal-free photocatalyst was studied under visible light. • Efficient removal of micropollutants from secondary urban wastewater was achieved. • g-C 3 N 4 was supported on glass rings to avoid its recovery from treated wastewater. Abstract Heterogeneous photocatalysis under visible light was employed for the degradation of organic micropollutants (MPs) found in the biologically treated effluents of an urban wastewater treatment plant (UWWTP). The irradiation source consisted in 4 light emitting diodes (LEDs) with a nominal power of 400–500 W m–2 at 417 nm. Metal-free exfoliated graphitic carbon nitride (gCN T), which was synthetized through a simple thermal treatment using dicyandiamide as precursor, was employed as photocatalyst. The gCN T material was characterized using different techniques: N 2 adsorption isotherms at 77 K, electron microscopy (scanning and transmission) and diffuse reflectance UV–Vis. The photocatalytic performance of the material was compared to the commercial TiO 2 -P25, confirming that gCN T led to a remarkable higher removal efficiency of the target MPs. Most of these MPs were removed in less than 10 min to levels below the limit of quantification (carbamazepine > isoproturon > clopidogrel > diclofenac > atenolol > bezafibrate > tramadol > venlafaxine > fluoxetine). Indirect photolysis, resulting from the secondary reactive oxidants generated during the irradiation of the aqueous matrix components, was found to partially contribute for the elimination of the occurring MPs. In addition, the gCN T photocatalyst was immobilized on glass rings for use under continuous mode operation, a minimum residence time of 25 min being required to attain significant removal efficiencies. Phytotoxicity experiments showed that heterogeneous photocatalysis did not enhance the toxicity of the wastewaters. [ABSTRACT FROM AUTHOR]

Although there are no legal discharge limits for micropollutants into the environment, some regulations have been published in the last few years. Recently, a watch list of substances for European Union-wide monitoring was reported in the Decision 2015/495/EU of 20 March 2015. Besides the substances previously recommended to be included by the Directive 39/2013/EU, namely two pharmaceuticals (diclofenac and the synthetic hormone 17-alpha-ethinylestradiol (EE2)) and a natural hormone (17-beta-estradiol (E2)), the first watch list of 10 substances/groups of substances also refers three macrolide antibiotics (azithromycin, clarithromycin and erythromycin), other natural hormone (estrone (E1)), some pesticides (methiocarb, oxadiazon, imidacloprid, thiacloprid, thiamethoxam, clothianidin, acetamiprid and triallate), a UV filter (2-ethylhexyl-4-methoxycinnamate) and an antioxidant (2,6-di-tert-butyl-4-methylphenol) commonly used as food additive. Since little is known about the removal of most of the substances included in the Decision 2015/495/EU, particularly regarding realistic concentrations in aqueous environmental samples, this review aims to: (i) overview the European policy in the water field; (ii) briefly describe the most commonly used conventional and advanced treatment processes to remove micropollutants; (iii) summarize the relevant data published in the last decade, regarding occurrence and removal in aqueous matrices of the 10 substances/groups of substances that were recently included in the first watch list for European Union monitoring (Decision 2015/495/EU); and (iv) highlight the lack of reports concerning some substances of the watch list, the study of un-spiked aquatic matrices and the assessment of transformation by-products. [ABSTRACT FROM AUTHOR]

The effect of different membranes, membrane modules, feed temperatures, flow rates and solute concentrations on the permeate flux and salt rejection in direct contact membrane distillation (DCMD) was first studied with synthetic seawater and compared to distilled water. After optimizing these operating conditions, DCMD was tested with real feed samples, namely river water (RW-R), seawater (SW-R), and a secondary effluent from a municipal wastewater treatment plant (MW-R). The permeate flux achieved with MW-R was significantly lower than those obtained with the other feed samples. Two membrane module configurations (H-cell and W-cell) were then studied using SW-S, spiking diphenhydramine (DP) as model organic pollutant in some experiments. The H-cell performed better in terms of permeate quality for the same volume of permeate collected. A long experiment (500 h) was conducted with SW-R employing a larger H-cell. Severe fouling was observed, but high rejections of ion species (>99%) were recorded together with complete rejections of pharmaceuticals (diclofenac, azithromycin, clarithromycin and erythromycin) detected in SW-R at 9.53–73.53 ng L −1 (detection limits <0.16 ng L −1 ). Colonies of Escherichia coli or enterococci were not detected in 100 mL of permeate (distillate) solution, complying with the European Directive for drinking water. [ABSTRACT FROM AUTHOR]

Photocatalytic ozonation was employed for the first time in continuous mode with TiO 2 -coated glass Raschig rings and light emitting diodes (LEDs) to treat urban wastewater as well as surface water collected from the supply area of a drinking water treatment plant (DWTP). Different levels of contamination and types of contaminants were considered in this work, including chemical priority substances (PSs) and contaminants of emerging concern (CECs), as well as potential human opportunistic antibiotic resistant bacteria and their genes (ARB&ARG). Photocatalytic ozonation was more effective than single ozonation (or even than TiO 2 catalytic ozonation) in the degradation of typical reaction by-products (such as oxalic acid), and more effective than photocatalysis to remove the parent micropollutants determined in urban wastewater. In fact, only fluoxetine, clarithromycin, erythromycin and 17-alpha-ethinylestradiol (EE2) were detected after photocatalytic ozonation, by using solid-phase extraction (SPE) pre-concentration and LC-MS/MS analysis. In surface water, this treatment allowed the removal of all determined micropollutants to levels below the limit of detection (0.01–0.20 ng L −1 ). The efficiency of this process was then assessed based on the capacity to remove different groups of cultivable microorganisms and housekeeping (16S rRNA) and antibiotic resistance or related genes ( intI1, blaTEM , qnrS , sul1 ). Photocatalytic ozonation was observed to efficiently remove microorganisms and ARGs. Although after storage total heterotrophic and ARB (to ciprofloxacin, gentamicin, meropenem), fungi, and the genes 16S rRNA and intI1 , increased to values close to the pre-treatment levels, the ARGs ( blaTEM , qnrS and sul1 ) were reduced to levels below/close to the quantification limit even after 3-days storage of treated surface water or wastewater. Yeast estrogen screen (YES), thiazolyl blue tetrazolium reduction (MTT) and lactate dehydrogenase (LDH) assays were also performed before and after photocatalytic ozonation to evaluate the potential estrogenic activity, the cellular metabolic activity and the cell viability. Compounds with estrogenic effects and significant differences concerning cell viability were not observed in any case. A slight cytotoxicity was only detected for Caco-2 and hCMEC/D3 cell lines after treatment of the urban wastewater, but not for L929 fibroblasts. [ABSTRACT FROM AUTHOR]

• N-doped reduced graphene oxide was synthesized using melamine (M) as N source (rGO-M). • A rGO-M-PVDF composite membrane was prepared by including rGO-M in a PVDF matrix. • rGO-M-PVDF promoted the activation of persulfate in continuous mode. • Conversions of micropollutants in the range 54–91% were obtained. • rGO-M-PVDF showed resistance towards fouling phenomena. Metal-free carbon-based polymer nanocomposite membranes were employed for the first time for activated persulfate oxidation in continuous mode of operation. For that purpose, reduced graphene oxide doped with nitrogen by using melamine as source (rGO-M) was included as catalytic active phase in a poly(vinylidene fluoride) matrix (PVDF). The performance of the resulting composite membrane (rGO-M-PVDF) was compared against that obtained with supported membranes prepared by simple filtration of rGO-M into a PTFE substrate. The uniform distribution of rGO-M within both the surface pores and cross-sectional channels of the composite rGO-M-PVDF membrane (with a thickness of 292 ± 20 μm) was confirmed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM), while its main structural features were studied by X-ray diffraction (XRD) and Raman spectroscopy. The quite good performance of this composite membrane was demonstrated by the degradation of three fluoroquinolone antibiotics at ppb level in ultrapure water (100 μg L−1 each), leading to average pollutant mass removal rates in the range 2.05–2.73 mg m−2 h−1. Conversions of the pharmaceuticals in the range 54–91% were obtained even after 24 h of operation in full continuous mode. Persulfate conversion was confirmed and high resistance to fouling was observed with this novel catalytic membrane. Average pollutant mass removal rates in the range 0.34–0.77 mg m−2 h−1 were obtained in preliminary experiments performed with surface water instead of ultrapure water, highlighting the need for additional studies on both water matrix effects and process optimization. [ABSTRACT FROM AUTHOR]