Search

This article introduces a power-efficient 24.25– 71-GHz multi-band phased-array receiver supporting all allocated fifth-generation mobile network new radio (5G NR) frequency range 2 (FR2) bands at 24/28/39/47 GHz and the potential 5G NR-U bands in unlicensed 57–71 GHz. A novel harmonic-selection technique is introduced to extend the operating bandwidth with low power consumption. By switching between the fundamental-selected mode, the second-harmonic-selected mode, and the third-harmonic-selected mode, only signals in the desired bands can be preserved, while the unselected mixing components are rejected. A dual-mode multi-band low-noise amplifier (LNA) based on a configurable transformer is adopted to realize broadband operation with minimized power consumption and noise figure (NF). The Hartley architecture is employed to further improve the image rejection performance. A hybrid-type polyphase filter (PPF) with a detector-based high-precision calibration block is utilized in this work to realize the Hartley operation with reduced insertion loss (IL). The proposed phased-array receiver is fabricated in a standard 65-nm bulk CMOS process. With the concerted efforts of all components, the proposed multi-band receiver can support 5G standard-compliant OFDMA-mode modulated signals up to 256QAM with a 400-MHz channel bandwidth from 24 to 71 GHz. Better than 36-dB inter-band blocker rejections can be maintained by this work. With existing of 0-dBc inter-band blockers at worst case frequencies, this receiver shows EVMs of −33.3, −30.9, −31.6, and −28.5 dB at 28, 39, 47.2, and 60.1 GHz, respectively. The power consumptions for a single receiver channel are 36, 32, 51, and 71 mW at 28, 39, 47.2, and 60.1 GHz, respectively. [ABSTRACT FROM AUTHOR]

This article introduces a power-efficient and low-cost CMOS 28-GHz phased-array beamformer supporting fifth-generation (5G) dual-polarized multiple-in-multiple-out (MIMO) (DP-MIMO) operation. To improve the cross-polarization (cross-pol.) isolation degraded by the antennas and propagation, a power-efficient analog-assisted cross-pol. leakage cancellation technique is implemented. After the high-accuracy cancellation, more than 41.3-dB cross-pol. isolation is maintained along with the transmitter array to the receiver array. The element-beamformer in this work adopts the compact neutralized bi-directional architecture featuring a minimized manufacturing cost. The proposed beamformer achieves 22% per path TX-mode efficiency and a 4.9-dB RX-mode noise figure. The required on-chip area for the beamformer is only 0.48 mm2. In over-the-air measurement, a 64-element dual-polarized phased-array module achieves 52.2-dBm saturated effective isotropic radiated power (EIRP). The 5G standard-compliant OFDMA-mode modulated signals of up to 256-QAM could be supported by the 64-element modules. With the help of the cross-pol. leakage cancellation technique, the proposed array module realizes improved DP-MIMO EVMs even under severe polarization coupling and rotation conditions. The measured DP-MIMO EVMs are 3.4% in both 64-QAM and 256-QAM. The consumed power per beamformer path is 186 mW in the TX mode and 88 mW in the RX mode. [ABSTRACT FROM AUTHOR]

This article presents a low-cost and area-efficient 28-GHz CMOS phased-array beamformer chip for 5G millimeter-wave dual-polarized multiple-in-multiple-out (MIMO) (DP-MIMO) systems. A neutralized bi-directional technique is introduced in this work to reduce the chip area significantly. With the proposed technique, completely the same circuit chain is shared between the transmitter and receiver. To further minimize the area, an active bi-directional vector-summing phase shifter is also introduced. Area-efficient and high-resolution active phase shifting could be realized in both TX and RX modes. In measurement, the achieved saturated output power for the TX-mode beamformer is 15.1 dBm. The RX-mode noise figure is 4.2 dB at 28 GHz. To evaluate the over-the-air performance, 16 H+16 V sub-array modules are implemented in this work. Each of the sub-array modules consists of four 4 H+4 V chips. Two sub-array modules in this work are capable of scanning the beam from −50° to +50°. A saturated EIRP of 45.6 dBm is realized by 32 TX-mode beamformers. Within 1-m distance, a maximum SC-mode data rate of 15 Gb/s and the 5G new radio downlink packets transmission in 256-QAM could be supported by the module. A 2 × 2 DP-MIMO communication is also demonstrated with two 5G new radio 64-QAM uplink streams. Thanks to the proposed area-efficient bi-directional technique, the required core area for a single element-beamformer is only 0.58 mm2. Compact and low-cost 5G millimeter-wave MIMO systems could be realized. [ABSTRACT FROM AUTHOR]

This article presents the first 39-GHz phased-array transceiver (TRX) chipset for fifth-generation new radio (5G NR). The proposed transceiver chipset consists of 4 sub-array TRX elements with local-oscillator (LO) phase-shifting architecture and built-in calibration on phase and amplitude. The calibration scheme is proposed to alleviate phase and amplitude mismatch between each sub-array TRX element, especially for a large-array transceiver system in the base station (BS). Based on LO phase-shifting architecture, the transceiver has a 0.04-dB maximum gain variation over the 360° full tuning range, allowing constant-gain characteristic during phase calibration. A phase-to-digital converter (PDC) and a high-resolution phase-detection mechanism are proposed for highly accurate phase calibration. The built-in calibration has a measured accuracy of 0.08° rms phase error and 0.01-dB rms amplitude error. Moreover, a pseudo-single-balanced mixer is proposed for LO-feedthrough (LOFT) cancellation and sub-array TRX LO-to-LO isolation. The transceiver is fabricated in standard 65-nm CMOS technology with flip-chip packaging. The 8TX–8RX phased-array transceiver module 1-m OTA measurement supports 5G NR 400-MHz 256-QAM OFDMA modulation with −30.0-dB EVM. The 64-element transceiver has a EIRPMAX of 53 dBm. The four-element chip consumes a power of 1.5 W in the TX mode and 0.5 W in the RX mode. [ABSTRACT FROM AUTHOR]