Search

This paper presents a new power electronic topology for a STATCOM allowing the generation of multilevel AC voltages. This topology is characterized by a modular configuration since it uses two well known four-leg two-level voltage source inverters. A Scott transformer with multiple secondary windings connects the two four-leg inverters to the grid. One of the important features of the proposed power topology is the capability to generate AC voltages with high number of levels, in spite of using only two four-leg two-level voltage source inverters. To maximize the number of voltage levels a geometric progression ratio of 3 between the windings of the transformers connected in cascade is proposed. However, to reduce the turns-ratio span, alternatively a fractional geometric ratio of 1.5 is also proposed and analyzed. A control strategy adapted to the proposed power converter topology is also presented. Besides the control of the reactive power the regulation of the four-leg inverter DC voltage will also be considered. To support the theoretical studies and assumptions, simulations and experiments are presented. Experimental results were obtained using a low power laboratory prototype. The results shown give evidence to the characteristics and features of the proposed power converter topology and control system. [ABSTRACT FROM AUTHOR]

In this paper, a static synchronous compensator (STATCOM) is proposed in which a new modular structure with conventional three-phase voltage source inverters is used to multilevel operation. The inverters are connected to a transformer in an open-end winding configuration and with three independent DC links. In this structure, the inverters will be connected in a cascade configuration. Besides the multilevel operation, the system is also characterized by low required blocking voltages for switch ratings, since the proposed STATCOM can apply the double of the DC capacitor voltage to the transformer windings. The development of the control system for the proposed topology is also presented. The operation of the proposed topology and the performance of the developed control system will be tested through several simulation and experimental tests. [ABSTRACT FROM AUTHOR]

This paper presents the effect of stray capacitances in bipolar (negative and/or positive) pulses generated by the two different topologies of the solid-state Marx modulators. According to the analysis, the stray capacitances influence the energy transfer from the Marx modulator capacitors to the load affecting the bipolar (negative and/or positive) pulse rise time. This paper deals with the structure design to reduce the influence of the stray capacitance and to improve the pulse rise time of these bipolar solid-state Marx modulators. A four-stage laboratory prototype of the two topologies has been assembled using 1200-V insulated gate bipolar transistors and diodes, operating with 1000-V dc input voltage and 1-kHz frequency, producing 4-kV bipolar pulses, with 5- \mu \texts pulse duration and 120-ns rise time, into a resistive load. [ABSTRACT FROM PUBLISHER]

Two solid-state bipolar Marx modulators are analyzed and compared regarding hold-off semiconductor voltages and open-fault tolerance capability. Normal and abnormal operating conditions are considered, such as switch synchronization mismatches, failures, and open faults. Ten-stage laboratory prototypes of two bipolar Marx modulators have been assembled using 1200-V insulated gate bipolar transistors and matching diodes, to operate at 500-V dc input voltage. Outputs are 4-kV bipolar pulses, 1% duty ratio, into resistive loads, and 1-kHz frequency. Lack of synchronization and open-fault tests confirm that only topologies with redundant switches can operate without semiconductors being subjected to double hold-off voltages while presenting current paths to clear faults. [ABSTRACT FROM PUBLISHER]

This paper presents a novel technique for the voltage droop compensation of long pulses in solid-state bipolar high-voltage Marx generators. Considering the modularity of Marx generators the compensation consists in adding one extra stage to perform as a pulsewidth modulation circuit. This stage voltage is added to the output positive or negative pulses, and an output LfCf filter is included to smooth the voltage pulse waveform. A five-stage laboratory prototype of this circuit has been assembled using 1200-V Insulated Gate Bipolar Transistors and diodes with 1000-V dc input voltage. The circuit was operated at 50-Hz bipolar pulse rate, giving 4-kV bipolar pulses, into a resistive load, with 100- \mu \texts pulsewidth and 9.5-ms relaxation time. The circuit was able to compensate 10% of bipolar pulse voltage droop. [ABSTRACT FROM PUBLISHER]