Search

This paper describes an efficient, repetitive nanosecond pulsed power generator using a Transmission-Line-Transformer (TLT) based multiple-switch technology. Within this setup, a 10-stage TLT and ten high-pressure spark-gap switches are adopted. At the input side, ten spark-gap switches are interconnected in series via the TLT, so that all the spark-gap switches can be synchronized automatically. At the output side, all the stages of the TLT are connected in parallel, thus a low output impedance (5 Ω) is obtained, and a large output current is realized by adding the currents through all the switches. Experimental results show that 10 spark-gap switches can be synchronized within about 10 ns. The system has been successfully demonstrated at repetition rates up to 300 pps (Pulses Per Second). Pulses with a rise-time of about 11 ns, a pulse width of about 55 ns, an energy of 9-24 J per pulse, a peak power of 300-810 MW, a peak voltage of 40-77 kV, and a peak current of 6-11 kA have been achieved with an energy conversion efficiency of 93-98%. [ABSTRACT FROM AUTHOR]

This paper describes an efficient, repetitive nanosecond pulsed power generator using a Transmission-Line-Transformer (TLT) based multiple-switch technology. Within this setup, a 10-stage TLT and ten high-pressure spark-gap switches are adopted. At the input side, ten spark-gap switches are interconnected in series via the TLT, so that all the spark-gap switches can be synchronized automatically. At the output side, all the stages of the TLT are connected in parallel, thus a low output impedance (5 Ω) is obtained, and a large output current is realized by adding the currents through all the switches. Experimental results show that 10 spark-gap switches can be synchronized within about 10 ns. The system has been successfully demonstrated at repetition rates up to 300 pps (Pulses Per Second). Pulses with a rise-time of about 11 ns, a pulse width of about 55 ns, an energy of 9-24 J per pulse, a peak power of 300-810 MW, a peak voltage of 40-77 kV, and a peak current of 6-11 kA have been achieved with an energy conversion efficiency of 93-98%. [ABSTRACT FROM AUTHOR]

Industrial application of nanosecond pulsed corona technology for air purification requires high volume, high-power plasma reactors. Cylinder-wire type reactors require multiple cylinders to meet these demands. Variations in pulse waveforms per cylinder, misalignment of wires, and jitter in streamer inception could lead to an uneven energy distribution over the cylinders. Nanosecond ICCD imaging is applied to a semi-industrial scale pulsed corona reactor to study streamer inception and propagation of the streamer plasma simultaneously in 16 cylinders. The images show streamer inception of all cylinders within 9 ns. Streamer propagation and intensities are very similar for all cylinders. [ABSTRACT FROM PUBLISHER]

For pulsed corona plasma applications, it becomes important to develop pilot systems with large average power and high-energy conversion efficiency. Since the beginning of 2000, we have been working on an industrial corona plasma system with tasks of 10-30 kW in average power and higher than 90% of total energy conversion efficiency. The pulsed-power source should have the following specifications: rise time of 10-25 as, pulsewidth of 50-150 as, pulse repetition rate of up to 1000 pulses per second, peak voltage pulse of 70 kV, peak current of 3.5 kA, dc bias voltage of 10-35 kV, and energy per pulse of up to 30 J. Sixteen parallel wire cylinder reactors are used to match the source. Gas and reactor temperatures can be controlled individually with water flow around the outside of those cylinders. The system is designed for gaseous oxidation and electrostatic dust precipitation. The system has been used for up to 17 kW in average power. This paper reports the system in detail, discusses issues related to the matching between the source and the reactor, and presents an example of industrial demonstrations on odor abatement at 1000 m³/h. Finally, this paper also gives a general guideline for design of corona plasma systems. [ABSTRACT FROM AUTHOR]

By the application of pulsed corona discharges in a carbon dioxide atmosphere over a water film, the formation of methane has been observed under mild reaction conditions, without the application of a dedicated catalyst. Methane is proposed to result from hydrogenation of carbon monoxide and possibly also carbon dioxide at the NiCr alloy high-voltage electrodes, the precursors being formed by plasma-induced decomposition of carbon dioxide and water. Applying energy densities up to 46 kJ/L has yielded methane levels of approximately 440 ppm at a production efficiency of 398 pmol/J. The observed plasma chemistry occurs at ambient pressure, while gas phase heat is cooled away by the water film, the latter being thermally nearly unaffected. [ABSTRACT FROM PUBLISHER]

Matching a pulse source to a plasma load is one of the main challenges to overcome to maximize the full potential of pulsed discharges for air purification applications. In this paper, we propose experiments that investigate the matching of a nanosecond pulse source to a corona plasma reactor that is aided by a high voltage on a tertiary electrode. The corona plasma reactor is a wire-cylinder reactor, as is commonly used in pulsed power plasmas. A tertiary electrode is situated on a dielectric layer against the cylinder of the reactor. On this tertiary electrode, we can apply a pulsed RF or dc voltage to provide an additional plasma and bias voltage in the corona plasma reactor. The pulse source that energizes the main corona plasma is the nanosecond pulse source of Kumamoto University, Japan. In this paper, we show the results of experiments with a dc voltage on the tertiary electrode. We varied the amplitude of the pulsed voltage as well as the dc voltage and investigated their effect on the corona plasma with energy and ozone measurements. The results show that the matching to the reactor increases with increasing dc voltages. However, the matching effect decreases with higher repetition rates. Furthermore, ozone measurements confirmed that a better matching also results in a higher ozone production, but in a lower ozone production energy yield. [ABSTRACT FROM PUBLISHER]

Although pulsed corona technology for air purification is widely investigated by the lab experiments, large-scale application has yet to be proven. Industrial systems require large flow handling and thus, high corona power. An autonomous semi-industrial scale pilot wire-cylinder type corona reactor has been constructed for air purification demonstrations. The reactor is powered by a 10-kW spark gap-based pulsed power supply, capable of generating 60-kV 100-ns wide pulses with 1-kHz repetition rate. The pulses are optionally superimposed on a 0–30-kV dc bias to enable electrostatic precipitation. The system has been successfully applied during several field and lab experiments. Conversion data as a function of energy density are presented for NOx, NH3, H2S, toluene, limonene, and fine dust removal. The system proves feasibility of large-scale air purification by pulsed corona. [ABSTRACT FROM AUTHOR]