Search

In this study, the electromagnetic performances of dual 3‐phase permanent magnet (PM) machines with coil span of two slot‐pitches are comparatively investigated. It mainly focuses on two PM machines with different slot/pole number combinations (Ns/2p), that is, the 24‐slot/10‐pole and 24‐slot/14‐pole machines (2p = Ns/2 ± 2). First, winding configurations are illustrated for these two dual 3‐phase machines with 30° angle displacement. Then, the winding factor, back electromotive force, average torque, torque ripple, iron and PM losses, short‐circuit (SC) current, and PM irreversible demagnetisation are analysed and compared for both machines on the conditions of healthy operation and one set of three‐phase fault, that is, SC or open circuit (OC), respectively. The comparative results show that on healthy condition the 14‐pole PM machine has a slightly larger torque output. Besides, on 3‐phase OC condition, the 14‐pole machine also performs better over‐rating torque capability. In terms of iron and PM losses, the 10‐pole machine has smaller iron losses but larger PM losses than the 14‐pole machine. Moreover, on 3‐phase SC condition, the 14‐pole machine has a significantly lower risk of PM irreversible demagnetisation than the 10‐pole machine, although both machines have very similar SC currents. Finally, the 24‐slot/10‐ and 14‐pole dual 3‐phase PM machines are both prototyped and some tests are carried out for validation. [ABSTRACT FROM AUTHOR]

In this article, the rotor stress is analysed for a high-speed permanent magnet (PM) machine (HSPMM) with segmented magnets retained by a carbon-fibre sleeve. The influence of rotor PM segmentation is firstly considered in the stress analysis. It is found that when the segmented magnets are under tensile stress, significant sleeve stress concentration will occur due to magnet edging effect. By contrast, the PMs will benefit from the segmentation with reduced tangential stress. This stress reduction effect is enhanced when the number of PM segments is larger. Furthermore, the influence of PM segmentation on the worst operating scenario is determined. In order to avoid stress concentration due to PM segmentation, the design guidelines are then given by investigating the influence of sleeve thickness and interference fit. A new design scheme of sleeve thickness is proposed based on the identified worst case scenarios. Finally, a 6-slot 4-pole high speed PM machine with segmented magnets retained by carbon-fibre sleeve is prototyped and tested at the speed of 90 krpm. The rotor stability indirectly indicts the validity of the theoretical analysis and design scheme. [ABSTRACT FROM AUTHOR]

In this paper, the iron loss models for electrical machines are first reviewed. One of the most accurate iron loss models, when the temperature is constant, is identified. An improved temperature-dependent iron loss model is also introduced. By applying the improved iron loss model to the electrical machine thermal analysis, the thermal and loss analyses can be fully coupled. Based on this, an improved thermal-loss coupling analysis method for electrical machine is developed in this paper. The electrical machine iron loss tests are carried out. The analysis and measurement results are then compared in order to validate the improved thermal-loss coupling analysis method. The comparison results indicate that the temperature prediction accuracy can be significantly improved by using the improved thermal-loss coupling analysis method. [ABSTRACT FROM AUTHOR]

In this paper, the different temperature dependencies of hysteresis and eddy current losses of non-oriented Si-steel laminations are investigated. The measured iron loss results show that both the hysteresis and eddy current losses vary linearly with temperature between 40 °C to 100 °C, a typical temperature range of electrical machines. Varying rates of hysteresis and eddy current losses with the temperature are different and fluctuate with flux density and frequency. Based on this, an improved iron loss model which can consider temperature dependencies of hysteresis and eddy current losses separately is developed. Based on the improved iron loss model, the temperature influence on the iron loss can be fully considered by measuring iron losses at only two different temperatures. The investigation is experimentally validated by both the tests based on a ring specimen and an electrical machine. [ABSTRACT FROM PUBLISHER]

In this paper, the temperature dependencies of iron loss under different flux densities, frequencies, and dc bias flux densities are systematically investigated. The temperature dependence of the hysteresis loss varies significantly with the dc bias flux density while that of the eddy current loss is independent of the dc bias flux density. Based on these different characteristics of the hysteresis and the eddy current iron losses, an improved iron loss model is developed. The temperature dependence of iron loss under dc bias condition can be considered by utilizing the improved iron loss model. The developed iron loss model is validated by both tests on laminations and an electrical machine. [ABSTRACT FROM AUTHOR]

In this paper, the investigation is focused on the iron loss prediction for electrical machines fed by low switching frequency inverter. An improved iron loss model is developed after reviewing various existing iron loss models considering pulse-width modulation (PWM) influence. In order to validate the improved iron loss model, iron loss tests are carried out on an electrical machine. The predicted iron loss results match well with the measured results, which shows that the improved iron loss model is able to predict iron loss in electrical machine fed by an inverter. The comparison between the predicted iron losses with and without considering the PWM influence shows that the iron loss can be significantly increased due to the influence of PWM, especially when the switching frequency is low. [ABSTRACT FROM AUTHOR]