Search

Pseudoestrogene bisphenol A (BPA) can be important ingredient of thermochromic inks, increasingly used materials in thermal printing paper, security printing, advertising, design and as temperature indicators in medicine and food industry. BPA mass fraction in thermochromic inks can be up to several percent. Hence, disposal of items with thermochromic prints pose a risk of environmental pollution. In this work BPA mass fraction was monitored during anaerobic degradation of papers with thermochromic prints in soil in both matrices: papers and soil. The degradation conditions simulated deeper layers of waste at a landfill site. Six types of papers with prints of thermochromic ink containing 2% of BPA were subjected to anaerobic degradation over up to 150 days.

Pulp and paper industries are very important for developing the Brazilian economy. During production processes, many effluents are generated with high polluting potential. The objective of this study is to conduct an extensive literature review on the characteristics of effluents and treatment forms adopted by Brazilian mills in this industrial sector. Most consulted studies address raw (without treatment) and secondary (after biological treatment) effluents, considering their main characteristics like pH, chemical and biochemical oxygen demands (COD and BOD, respectively), color, solids, organochlorines, toxicity, estrogenic activity, and phenols. Raw effluents differ considerably in composition, depending on the type of paper produced, the pulping process employed, and other steps, like pulp bleaching. Raw effluent characteristics indicate that this effluent cannot be directly disposed of into water bodies, because it does not comply with federal and state disposal standards. Secondary effluents normally comply with Brazilian legislations, although some studies have reported COD and total phenol concentrations higher than disposal standards, suggesting that additional treatments are necessary. Treated effluent reuse was verified in some Brazilian mills, while its disposal in eucalyptus plantations has been considered a promising alternative for irrigation purposes.

The amount of compostable bioplastics collected with the food waste is constantly growing, particularly due to the bags used for collection. According to the Italian legislation, compostable bioplastics must be accepted by all biological treatment plants, including aerobic and anaerobic facilities. Anyway, the compostability standard requires only the assessment of the aerobic degradability, while it is generally not required to test the behaviour under anaerobic conditions. This aspect is evaluated in the paper, where the anaerobic degradability of bioplastic bags used for the food waste collection is assessed. First, Biochemical Methane Potential (BMP) tests were performed on four commercial types of bioplastic bags, including those designed only for the collection of food waste and the shoppers, that can be reused for the same purpose. Subsequently, an innovative approach for this kind of substrate was applied, subjecting two bags to semi-continuous co-digestion tests together with the food waste. Both tests were performed by comparing the behaviour of bioplastic bags with that of an alternative collection paper bag. Finally, tests to evaluate the influence of physical phenomena on the degradation of bioplastics were performed to better understand the results of biological tests. BMP tests indicated a good degradability (71%) of bioplastic bags, while semi-continuous tests showed a much lower degradability (27%), confirmed by the observation of the undigested bag pieces. On the contrary, the paper bag presents interesting characteristics, because its degradability in the semi-continuous tests (82%) resulted even higher than that observed in the BMP tests (74%). These results highlight an important difference between the bags mono-digestion by means of BMP tests and the semi-continuous co-digestion tests with food waste, which better simulate the full-scale operational conditions.

Early and on-site detection of environmental contaminations and physicochemical parameters of seawater is increasingly preferred to guarantee hazard minimization in many settings. In this paper, we describe a combination of microfluidic paper-based sensors (µPADs) and an Android-based smartphone application (App) for simultaneous on-site quantification of phosphate (PO

The pulp and paper industry consumes a huge amount of water and releases more polluted and colored wastewater every year. Many conventional techniques are used in the treatment of paper industry wastewater. However, for color removal from paper mill effluent, there is no proven method so far, on an industrial scale. Due to high energy input and high cost, there is an urgent need to find out a new technique that must be sustainable, economical, and environment friendly. Various methods have been investigated on bench scale and pilot scale also but no proven method for color removal on an industrial scale. The paper provides an overview of the color removal techniques from different sources of pulp and paper mill wastewater discharged by various industries. The review described various components involved in various processes for color removal from paper mill waste water. The present works focus on processes like chemical, chemical/physical, biological, physicochemical, and electrochemical applied in color removal from paper mill wastewater. The present review gives key information on the effectiveness, use, betterment, and limitations of numerous methods of treatment targeted at color removal from paper mill wastewater using various techniques still under evolution.

Funding Information: The authors are grateful with Arauco Bioforest S.A. for giving the right to use the presented results. Publisher Copyright: © 2021 The Authors A pulsed electrodialysis reversal (pEDR) process is proposed to desalinate spent water after particle removal, biological and chemical coagulation, which are commonly used as a sequence in Kraft pulp mills. pEDR affords closed-loop processing, reducing the need for freshwater intake while maintaining the quality of recirculating process streams. Compared with conventional electrodialysis, pEDR minimizes production losses (from 5 % to 0.6 %), extending the time for hydraulic reversal (from 15 min to at least 2 h). Simultaneously, the conductivity of the effluent is significantly reduced, from 2100 to 200 μS/cm, reaching a quality similar to the feed water. The operation cost (0.38 US$/m3) is factored in the techno-economic viability of the process water recirculation, which is also demonstrated for its scalability. Additionally, WinGEMS simulation highlights the benefits of installing a pEDR unit, positively impacting mill water under different recirculation rates. Overall, we show remarkable gains in water economy, operation (maintenance and fouling), and quality, which are critical factors in achieving resource sufficiency.

In this study, we investigated the airborne particles released during paper printing and paper shredding processes in an attempt to characterize and differentiate these particles. Particle characteristics were studied with real time instruments (RTIs) to measure concentrations and with samplers to collect particles for subsequent microscopy and cytotoxicity analysis. The particles released by paper shredding were evaluated for cytotoxicity by using in vitro human lung epithelial cell models. A substantial amount of particles were released during both the shredding and printing processes. We found that the printing process caused substantial release of particles with sizes of less than 300 nm in the form of metal granules and graphite. These released particles contained various elements including Al, Ca, Cu, Fe, Mg, N, K, P, S and Si. The particles released by the paper shredding processes were primarily nanoparticles and had a peak size between 27.4 nm and 36.5 nm. These paper particles contained elements including Al, Br Ca, Cl, Cr, Cu, Fe, Mg, N, Na, Ni P, S and Si, as determined by scanning electron microscope-energy dispersive X-ray spectroscopy (SEM-EDS) and single-particle inductively coupled plasma-mass spectroscopy (SP-ICP-MS) analysis. Although various metals were identified in the paper particles, these particles did not elicit cytotoxicity to simian virus-transformed bronchial epithelial cells (BEAS2B) and immortalized normal human bronchial epithelial cells (HBE1). However, future studies should investigate other cytotoxicity effects of these paper particles in various types of lung cells to identify potential health effects of the particles.

Generally, the mechanical strength and stiffness of old corrugated cardboard (OCC) waste paper are decreased after multiple recycling procedures. Surface sizing starch, which is extensively used in the surface sizing of paper making, accumulates after dissolving from the fibers and is transformed into pollutant during the OCC re-pulping process. To overcome the pollution and reutilization problem of the waste starch during the recycling process of OCC paper, waste starch was ionized using hydrogen peroxide (H2O2) to improve the mechanical properties of OCC paper during the reutilization. The results showed that the carboxyl group of waste starch increased with an increasing degree of ionization, resulting in enhanced copper ion adsorption capacity. Furthermore, the retention rate of the modified starch in the wet-end increased from 18.0% to 48.2%. The OCC paper presented the highest burst index and tensile strength of 8.94 kPa m2/g and 112.5 N m/g, respectively, when MS-2 was added. This work has great significance for implementation of the cleaning production of OCC waste papers and the reutilization of the waste starch.

Recycled paper fiber rejects have shown potential as a source of waste-to-resource carbohydrates for renewable chemicals production. This study examined three classes of recycled paper fines (old corrugated containers, old newspaper, and mixed office waste) and two industrial papermaking rejects streams from different recycling mills (one mill processes linerboard and the other old corrugated cardboard). The effect of chemical pretreatment using dilute sodium hydroxide, hot water and dilute sulfuric acid on enzymatic glucose and xylose yields was evaluated. Enzymatic hydrolysis results indicated that recycled fiber streams with more old corrugated cardboard have higher potential to produce carbohydrates. The recycled cardboard rejects produced more glucose and xylose per kilogram of rejects than the linerboard rejects under all untreated and pretreated conditions. The highest producing rejects sample was sodium hydroxide pretreated cardboard rejects with 373 g glucose and 61 g xylose produced per kilogram of rejects. However, a simple hot water pretreatment showed similar results, with 335 g glucose and 58 g xylose produced per kilogram of rejects. The hot water pretreatment is recommended due to its comparable yield and lower chemical addition.

Background There has been growing interest in the development of waste-specific decay factors for estimation of greenhouse gas emissions from landfills in national greenhouse gas inventories. Although engineered wood products (EWPs) and paper represent a substantial component of the solid waste stream, there is limited information available on their carbon dynamics in landfills. The objective of this study was to determine the extent of carbon loss for EWPs and paper products commonly used in Australia. Experiments were conducted under laboratory conditions designed to simulate optimal anaerobic biodegradation in a landfill. Results Methane generation rates over incubations of 307–677 days ranged from zero for medium-density fibreboard (MDF) to 326 mL CH4 g−1 for copy paper. Carbon losses for particleboard and MDF ranged from 0.7 to 1.6%, consistent with previous estimates. Carbon loss for the exterior wall panel product (2.8%) was consistent with the expected value for blackbutt, the main wood type used in its manufacture. Carbon loss for bamboo (11.4%) was significantly higher than for EWPs. Carbon losses for the three types of copy paper tested ranged from 72.4 to 82.5%, and were significantly higher than for cardboard (27.3–43.8%). Cardboard that had been buried in landfill for 20 years had a carbon loss of 27.3%—indicating that environmental conditions in the landfill did not support complete decomposition of the available carbon. Thus carbon losses for paper products as measured in bioreactors clearly overestimate those in actual landfills. Carbon losses, as estimated by gas generation, were on average lower than those derived by mass balance. The low carbon loss for particleboard and MDF is consistent with carbon loss for Australian wood types described in previous studies. A factor for carbon loss for combined EWPs and wood in landfills in Australia of 1.3% and for paper of 48% is proposed. Conclusions The new suggested combined decay factor for wood and EWPs represents a significant reduction from the current factor used in the Australian greenhouse gas inventory; whereas the suggested decay factor for paper is similar to the current decay factor. Our results improve current understanding of the carbon dynamics of harvested wood products, and allow more refined estimates of methane emissions from landfills. Electronic supplementary material The online version of this article (10.1186/s13021-018-0115-3) contains supplementary material, which is available to authorized users.

Sewage sludge/biosolids are by-wastes of municipal and industrial wastewater treatment. As sources of nutrients (C, N, P) they are widely used in intensive farming where large supplementation of organic matter to maintain fertility and enhance crop yields is needed. However, according to the report of European Commission published in 2010, only 39% of produced sewage sludge is recycled into agriculture in the European Union. This situation occurs mainly due to the fact, that the sewage sludge may contain a dangerous volume of different contaminants. For over decades, a great deal of attention has been focused on total concentration of few heavy metals and pathogenic bacteria Salmonella and Escherichia coli. The Sewage Sludge Directive (86/278/EEC) regulates the allowable limits of Zn, Cu, Ni, Pb, Cd, Cr and Hg and pathogens and allows for recovery of sludge on land under defined sanitary and environmentally sound conditions. In this paper, a review on quality of sewage sludge based on the publications after 2010 has been presented. Nowadays there are several papers focusing on new serious threats to human health and ecosystem occurring in sewage sludge – both chemicals (such as toxic trace elements – Se, Ag, Ti; nanoparticles; polyaromatic hydrocarbons; polychlorinated biphenyl; perfluorinated surfactants, polycyclic musks, siloxanes, pesticides, phenols, sweeteners, personal care products, pharmaceuticals, benzotriazoles) and biological traits (Legionella, Yersinia, Escherichia coli O157:H7)., Highlights • Sewage sludge contains organic and inorganic contaminants not regulated by law. • Total content of many compounds (heavy metals) is not a reliable indicator of toxicity. • Regular monitoring is crucial to limit a release of toxic substances to ecosystem.

Health risks from air pollutants are evaluated by comparing chronic (i.e., an average over 1 yr or greater) or acute (typically 1-hr) exposure estimates with chemical- and duration-specific reference values or standards. When estimating long-term pollutant concentrations via exposure modeling, facility-level annual average emission rates are readily available as model inputs for most air pollutants. In contrast, there are far fewer facility-level hour-by-hour emission rates available for many of these same pollutants. In this report, we first analyze hour-by-hour emission rates for total reduced sulfur (TRS) compounds from eight kraft pulp mill operations. This data set is used to demonstrate discrepancies between estimating exposure based on a single TRS emission rate that has been calculated as the mean of all operating hours of the year, as opposed to reported hourly emission rates. A similar analysis is then performed using reported hourly emission rates for sulfur dioxide (SO2) and oxides of nitrogen (NOx) from three power generating units from a U.S. power plant. Results demonstrate greater variability at kraft pulp mill operations, with ratios of reported hourly to average hourly TRS emissions ranging from less than 1 to greater than 160 during routine facility operations. Thus, if fluctuations in hourly emission rates are not accounted for, over- or underestimates of hourly exposure, and thus acute health risk, may occur. In addition to this analysis, we also demonstrate an additional challenge when assessing health risk based on hourly exposures: the lack of human health reference values based on 1-hr exposures. Implications: Largely due to the lack of reported hourly emission rate data for many air pollutants, an hourly average emission rate (calculated from an annual emission rate) is often used when modeling the potential for acute health risk. We calculated ratios between reported hourly and hourly average emission rates from pulp and paper mills and a U.S. power plant to demonstrate that if not considered, hourly fluctuations in emissions could result in an over- or underestimation of exposure and risk. We also demonstrate the lack of 1-hr human health reference values meant to be protective of the general population, including children.

Management of municipal solid waste is an efficient method to increase resource efficiency, as well as to replace fossil fuels with renewable energy sources due to that (1) waste to a large extent is renewable as it consists of food waste, paper, wood etc. and (2) when energy and materials are recovered from waste treatment, fossil fuels can be substituted. In this paper results from a comprehensive system study of future biological treatment of readily degradable waste in two Swedish regions are presented. Different collection and separation systems for food waste in households have been applied as well as technical improvements of the biogas process as to reduce environmental impact. The results show that central sorting of a mixed fraction into recyclables, combustibles, biowaste and inert is a competitive option compared to source separation. Use of pellets is beneficial compared to direct spreading as fertiliser. Fuel pellets seem to be the most favourable option, which to a large extent depends on the circumstances in the energy system. Separation and utilisation of nitrogen in the wet part of the digestion residue is made possible with a number of technologies which decreases environmental impact drastically, however to a substantial cost in some cases.

The total emission control target of water pollutants (e.g., COD and NH 4 –N) for a certain industrial sector can be predicted and analysed using the popular technology-based bottom-up modelling. However, this methodology has obvious uncertainty regarding the attainment of mitigation targets. The primary uncertainty comes from macro-production, pollutant reduction roadmap, and technical parameters. This research takes the paper and pulp industry in China as an example, and builds 5 mitigation scenarios via different combinations of raw material structure, scale structure, procedure mitigation technology, and end-of-pipe treatment technology. Using the methodology of uncertainty analysis via Monte Carlo, random sampling was conducted over a hundred thousand times. According to key parameters, sensitive parameters that impact total emission control targets such as industrial output, technique structure, cleaner production technology, and end-of-pipe treatment technology are discussed in this article. It appears that scenario uncertainty has a larger influence on COD emission than NH 4 –N, hence it is recommended that a looser total emission control target for COD is necessary to increase its feasibility and availability while maintaining the status quo of NH 4 –N. Consequently, from uncertainty analysis, this research recognizes the sensitive products, techniques, and technologies affecting industrial water pollution.

Pulp and paper mill sludge is a waste stream derived from the pulp and paper making industry, comprised of organic and inorganic material in the form of cellulose, hemicellulose, lignin and ash. In South Africa, approximately fivefour hundred thousand wet tonnes are produced per annum and is currently disposed via landfilling or incineration. However, these disposal methods raise environmental and financial concerns. This waste stream is an attractive feedstock for fermentable sugars, mainly glucose, recovery and can be redirected for valorisation as a feedstock for microbial fermentation to produce value-added products. Sugar recovery by enzymatic hydrolysis, as opposed to acidic hydrolysis, is a promising approach but is hampered by the lignin and inorganic material found in pulp and paper mill sludge. Several treatment steps to reduce or remove these components prior to enzymatic hydrolysis are assessed in this review. Pretreatment improves hydrolysis of cellulosic fibres and ensures a substantial yield of sugars.

The pulp and paper industry is highly dependent on forest and water resources. It has more concerns on fair utilization of these resources and their conservation for its further expansion. Present study emphasizes on the use of rice straw (agro waste) in papermaking to protect wood based resources. It further deals with ozone bleaching (Z) prior to elemental chlorine free bleaching that proved to be significant in terms of reducing the effluent load specially the reduction in toxic, recalcitrant and carcinogenic compounds. Z based sequences resulted in pulp brightness of ∼85% that was 3.6% higher than the elemental chlorine free bleaching. Bleached pulps of Z based sequences were found to be having better strength properties than elemental chlorine based sequence and thus may be adopted as improved bleaching technology. The analysis of handsheets prepared after pulp bleaching was performed using X-Ray diffraction, ATR-FTIR and SEM. Incorporating ozone stage resulted in marked reduction of 58% and 63% in total solids in bleaching wastewater. Reduction of more than 80% in BOD, COD and adsorbable organic halides was achieved in Z based bleaching in comparison to chlorine bleaching. The amount of chlorophenols, guaiacols, catechols, vanillins and syringols became negligible (approx. 90% reduction) in effluents of Z based bleaching sequences. The chlorine dioxide followed by peroxide bleaching after Z stage was found to be the most promising to reduce the effluent load.

Refining is the major process of paper formation. This study focuses on the impact of a specific enzyme (Paenibacillus cellulase) for fibers on the surfaces, the roughness and height of the fibers are also investigated. Effects of enzyme dosages and the mechanical refining action (PFI revolution) on fiber physical properties were also analyzed. The fibers were observed by scanning electron microscopy (SEM), their roughness and height were analyzed by Atomic force microscopy (AFM). Results show that the Paenibacillus cellulase pretreatment increased the drainability of both kinds of pulp at the same level of refining energy. In other words, enzymatic treatment on pulp refining consumed less refining revolutions to reach the same drainability compared to the untreated pulp. Although the viscosity of both kinds of pulp was degraded with the enzymatic treatment, the physical properties of paper had no significantly negative influence on them. The results indicated the treatment with cellulase swelled the fibers in the absence of refining, and there were better fibrillation on the fibers treated with cellulase after refining. Furthermore, the statistical analysis of AFM suggested that both kinds of pulp treated with low cellulase dosage with PFI refining had higher roughness.

The contribution of domestic lignocellulosic waste and its potential for biodegradation by components, for each category of paper and cardboard, have scarcely been reported. To achieve integral proposals, for managing this type of waste, is essential to know each individual contribution to the &ldquo, paper and cardboard&rdquo, category. The objective of this study was to characterize the paper and cardboard waste from the domestic solid waste stream, in the city of Morelia, Mexico, and estimate its methane generation potential (CH4). The generation of lignocellulosic waste was studied in a housing complex of social interest. The domestic lignocellulosic residues (DLW) that were chemically characterized were derived from paper and cardboard. The average daily generation was 0.5 kg/inhabitant. The highest content of lignin was found in newspaper (24.5%), and toilet paper was the material with the lowest lignin content (1%). The bond paper had a DLW of higher YCH4, when degraded anaerobically, in a semi-solid phase and a mesophilic regime. The variety of paper and cardboard, such as DLW, presented differences in their generation (kg/person), chemical composition (lignin content), and their potential for anaerobic biodegradability.

The safe disposal of pulp and paper mill effluent is still a threat to the environment due to the presence of several unknown organic pollutants. The comparative physico-chemical analysis of pulp and paper mill effluent-contaminated sediment (PPECS) of site 1 and site 2 showed that the sediment had an alkaline nature and was loaded with several organic pollutants and heavy metals. SEM-EDX examination showed a porous structure with a heterogeneous distribution of particles, allowing the adsorption of metal and other complex organic ions. FTIR analysis depicted the presence of a variety of functional groups, i.e., alkyl halides, phenolics, and lignin, in the contaminated sediment. GC-MS analysis showed the major presence of organic pollutants, i.e., 2-methyl-4-keto-2-pentan-2-ol and 3,7-dioxa-2,8-disilanonane,2,2,8,8-tetramethyl-5-[(trimethylsilyl)oxy], in the site 1 sediment contaminated with pulp and paper mill waste, while 2-methyl-4-keto-2-trimethylsiloxypentane, 4-ethyl-2-methoxyphenol, ethyl-2-octynoate, cis-9-hexadecenoic acid, and octadecenoic acid were detected in the site 2 sediment contaminated with pulp and paper mill waste. The genotoxicity of PPECS determined by examining Allium cepa root cell division showed chromosomal aberration. In this study, several compounds that have not been reported before were identified.

Pulp-and-paper mills produce various types of contaminants and a significant amount of wastewater depending on the type of processes used in the plant. Since the generated wastewaters can be potentially polluting and very dangerous, they should be treated in wastewater treatment plants before being released to the environment. This paper reviews different wastewater treatment processes used in the pulp-and-paper industry and compares them with respect to their contaminant removal efficiencies and the extent of greenhouse gas (GHG) emission. It also evaluates the impact of operating parameters on the performance of different treatment processes. Two mathematical models were used to estimate GHG emission in common biological treatment processes used in the pulp-and-paper industry. Nutrient removal processes and sludge treatment are discussed and their associated GHG emissions are calculated. Although both aerobic and anaerobic biological processes are appropriate for wastewater treatment, their combination known as hybrid processes showed a better contaminant removal capacity at higher efficiencies under optimized operating conditions with reduced GHG emission and energy costs.

Burning of joss paper and incense is still a very common traditional custom in countries with a majority Chinese population. The Hungry Ghost Festival which is celebrated in the 7 month of the Chinese calendar is one of the events where joss paper and incense are burned as offerings. This study investigates the impact of the Ghost Month Festival (open burning event) on air quality by analysis of the chemical composition of particulate matter (PM) and rainwater samples collected during this event, compared with data collected throughout the year, as well as bottom ash samples from burning the original joss paper and incense. The results showed that the change in the chemical composition of the rainwater and PM2.5 (PM ≤ 2.5 μm) atmospheric samples could be correlated directly with burning events during this festival, with many elements increasing between 18% and 60% during August and September compared to the yearly mean concentrations. The order of percentage increase in elemental composition (in rain water and PM2.5) during the Hungry Ghost Festival is as follows: Zn > Ca > K > Mg > Fe > Al > Na ∼ Mn ∼ Ti ∼ V > Cu > As > Ni > Co > Cd > Cr > Pb. The chemical composition of the original source materials (joss paper and incense for combustion) and their associated bottom ash were analysed to explain the impact of burning on air quality. MOE (Min. of Education, S’pore) Published version

Large areas of mine tailings are reclaimed by applying organic amendments such as paper mill sludge (PMS). Although mining industries can use PMS freshly generated by paper mills, operational constraints on paper industries make temporary landfilling of this material an unavoidable alternative for the paper industries, creating the most prominent PMS source for mining industries. This study aimed to quantify soil greenhouse gas (GHG) emissions (N2O, CO2, and CH4) after application of landfilled PMS (LPMS; i.e., excavated from a landfill site at a paper mill) and LPMS combined with a seeding treatment of white clover (Trifolium repens L.) on nonacidic mine tailings site prior to reforestation. Soil N2O, CO2, and CH4 fluxes were measured after applications of 50 and 100 Mg dry LPMS ha−1 during two consecutive snowfree seasons on two adjacent sites; LPMS was applied once in the first season. The LPMS application increased N2O emissions (7.6 to 34.7 kg N2O-N ha−1, comprising 1.04 to 2.43% of applied N) compared with the unamended control during the first season; these emissions were negligible during the second season. The LPMS application increased CO2 emissions (~5800 to 11,400 kg CO2–C ha−1, comprising 7 to 27% of applied C) compared with the unamended control on both sites and in both seasons. Fluxes of CH4 were negligible. White clover combined with LPMS treatments did not affect soil GHG emissions. These new GHG emission factors should be integrated into life-cycle analyses to evaluate the C footprint of potential symbioses between the mining and paper industries. Future research should focus on the effect of PMS applications on soil GHG emissions from a variety of mine tailings under various management practices and climatic conditions to plan responsible and sustainable land reclamation.

Advanced Oxidation Processes (AOPs) are called to fill the gap between the treatability attained by conventional physico-chemical and biological treatments and the day-to-day more exigent limits fixed by environmental regulations. They are particularly important for the removal of anthropogenic pollutants and for this reason, they have been widely investigated in the last decades and even applied in the treatment of many industrial wastewater flows. However, despite the great development reached, AOPs cannot be considered mature yet and there are many new fields worthy of research. Some of them are going to be briefly introduced in this paper, including hybrid processes, heterogeneous semiconductor photocatalysis, sulphate-radical oxidation and electrochemical advanced oxidation for water/wastewater treatment. Moreover, the use of photoelectrochemical processes for energy production is discussed. The work ends with some perspectives that can be of interest for the ongoing and future research., Los Procesos de Oxidación Avanzada (POAs) están llamados a llenar el vacío entre la tratabilidad alcanzada por los tratamientos físico-químicos y biológicos convencionales y los límites cada día más exigentes fijados por la normativa medioambiental. Son particularmente importantes para la remoción de contaminantes antropogénicos y por esta razón han sido ampliamente investigados en las últimas décadas e incluso aplicados en el tratamiento de muchos flujos de aguas residuales industriales. Sin embargo, a pesar del gran desarrollo alcanzado, los POA aún no pueden considerarse maduros y existen muchos campos nuevos dignos de investigación. Algunos de ellos se presentarán brevemente en este artículo, incluidos los procesos híbridos, la fotocatálisis de semiconductores heterogéneos, la oxidación por radicales de sulfato y la oxidación electroquímica avanzada para el tratamiento de agua/aguas residuales. Además, se discute el uso de procesos fotoelectroquímicos para la producción de energía. El trabajo finaliza con algunas perspectivas que pueden ser de interés para las investigaciones en curso y futuras.

A bleached kraft pulp mill in Nova Scotia has discharged effluent wastewater into Boat Harbour, a former tidal estuary within Pictou Landing First Nation since 1967. Fifty years of effluent discharge into Boat Harbour has created >170,000 m3 of unconsolidated sediment, impacted by inorganic and organic contaminants, including metal[loid]s, polycyclic aromatic hydrocarbons (PAHs), dioxins, and furans. This study aimed to characterize metal(loid)-impacted sediments to inform decisions for a $89 million CAD sediment remediation program. The remediation goals are to return this impacted aquatic site to pre-mill tidal conditions. To understand historical sediment characteristics, spatiotemporal variation covering ~quarter century, of metal(loid) sediment concentrations across 103 Boat Harbour samples from 81 stations and four reference locations, were assessed by reviewing secondary data from 1992 to 2015. Metal(loid) sediment concentrations were compared to current Canadian freshwater and marine sediment quality guidelines (SQGs). Seven metal(loid)s, As, Cd, Cr, Cu, Pb, Hg, and Zn, exceeded low effect freshwater and marine SQGs; six, As, Cd, Cr, Pb, Hg, and Zn, exceeded severe effect freshwater SQGs; and four, Cd, Cu, Hg, and Zn, exceeded severe effect marine SQGs. Metal(loid) concentrations varied widely across three distinct temporal periods. Significantly higher Cd, Cu, Pb, Hg, and Zn concentrations were measured between 1998 and 2000, compared to earlier, 1992–1996 and more recent 2003–2015 data. Most samples, 69%, were shallow (0–15 cm), leaving deeper horizons under-characterized. Geographic information system (GIS) techniques also revealed inadequate spatial coverage, presenting challenges for remedy decisions regarding vertical and horizontal delineation of contaminants. Review of historical monitoring data revealed that gaps still exist in our understanding of sediment characteristics in Boat Harbour, including spatial, vertical and horizontal, and temporal variation of sediment contamination. To help return Boat Harbour to a tidal estuary, more detailed sampling is required to better characterize these sediments and to establish appropriate reference (background) concentrations to help develop cost-effective remediation approaches for this decades-old problem.

The competence of novel fungal consortium, consisting of Nigrospora sp. LDF00204 (accession no. KP732542) and Curvularia lunata LDF21 (accession no. KU664593), was investigated for the treatment of pulp and paper mill effluent. Fungal consortium exhibited enhanced biomass production under optimized medium conditions, i.e., glucose as carbon (C), sodium nitrate as nitrogen (N), C/N 1.5:0.5, pH 5, temperature 30 °C, and agitation 140 rpm, and significantly reduced biochemical oxygen demand (85.6%), chemical oxygen demand (80%), color (82.3%), and lignin concentration (76.1%) under catalytic enzyme activity; however, unutilized ligninolytic enzymes, such as laccase (Lac), manganese peroxidase (MnP), and lignin peroxidase (LiP), were observed to be 13.5, 11.4, and 9.4 U/ml after the third cycle of effluent treatment in repeated batch process. Scanning electron microscopy (SEM) of fungal consortium revealed their compatibility through intermingled hyphae and spores, while the FTIR spectra confirmed the alteration of functional groups ensuring structural changes during the effluent treatment. Gas chromatography/mass spectroscopy (GC-MS) analysis showed the reduction of complex compounds and development of numerous low-molecular-weight metabolites, such as 1-3-dimethyl benzene, 2-chloro-3-methyl butane, pentadecanoic acid, and 1-2-benzene dicarboxylic acid, during the treatment, demonstrating the massive potential of the novel fungal consortium to degrade recalcitrant industrial pollutants.

Pulp and paper industry produces massive amounts of sludge from wastewater treatment, which constitute an enormous environmental challenge. A possible management option is the conversion of sludge into carbon-based adsorbents to be applied in water remediation. For such utilization it is important to investigate if sludge is a consistent raw material originating reproducible final materials (either over time or from different manufacturing processes), which is the main goal of this work. For that purpose, different primary (PS) and biological sludge (BS) batches from two factories with different operation modes were sampled and subjected to pyrolysis (P materials) and to pyrolysis followed by acid washing (PW materials). All the materials were characterized by proximate analysis, total organic carbon (TOC) and inorganic carbon (IC), attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR) and N2 adsorption isotherms (specific surface area (SBET)and porosity determination). Sludge from the two factories proved to have distinct physicochemical properties, mainly in what concerns IC. After pyrolysis, the washing step was essential to reduce IC and to considerably increase SBET, yet with high impact in the final production yield. Among the materials here produced, PW materials from PS were those having the highest SBET values (387-488 m2 g-1). Overall, it was found that precursors from different factories might originate final materials with distinct characteristics, being essential to take into account this source of variability when considering paper mill sludge as a raw material. Nevertheless, for PS, low variability was found between batches, which points out to the reliability of such residues to be used as precursors of carbon adsorbents. L'Oreal Portugal published

The general tendency in the pulp industry towards reduced fresh water consumption and minimum effluent causes major deposit problems in mills. Chemical pulp bleach plants are affected by several types of mineral deposits, the most frequent being calcite, barite and calcium oxalate. In this review, the phenomena leading to scaling in chemical pulp bleaching are discussed, together with strategies for limiting deposits. The merits of various chemical methods in estimating scaling risks are compared. Chemical speciation methods are used throughout this review to gain a better understanding and prediction of scaling phenomena. Coupled chemical process simulations are anticipated to be a crucial way of solving deposition problems in bleach plants.

Hemicelluloses and lignin present in the spent liquor (SL) of neutral sulfite semichemical (NSSC) pulping process can potentially be converted into value-added products such as furfural, hydroxymethylfurfural, levulinic acid, phenols and adhesives. However, the direct conversion of hemicelluloses and lignin of SL into value-added products is uneconomical due to the dilute nature of the SL. To have a feasible downstream process for utilizing lignocelluloses of SL, the lignocelluloses should initially be separated from the SL. In this study, an adsorption process (via applying activated carbon) was considered for isolating the dissolved lignin and hemicelluloses from the SL of an NSSC pulping process. Under the optimal conditions of pH, SL/AC weight ratio, time and temperature of 5.7, 30, 360 min and 30 °C, the maximum lignin and hemicellulose adsorptions were 0.33 and 0.25 g/g on AC. The chemical oxygen demand (COD) and turbidity of the SL were decreased by 11% and 39%, respectively, as a result of lignocellulose adsorption on AC. Also, the incineration behavior of the SL-treated AC was studied with a thermo-gravimetric analysis (TGA).

A lab-scale granular activated carbon sequencing batch biofilm reactor (GAC-SBBR), a combined adsorption and biological process, was developed to treat real wastewater from a recycled paper mill. In this study, one-consortia of mixed culture (4000–5000 mg/L) originating from recycled paper mill activated sludge from Kajang, Malaysia was acclimatized. The GAC-SBBR was fed with real wastewater taken from the same recycled paper mill, which had a high concentration of chemical oxygen demand (COD) and adsorbable organic halides (AOX). The operational duration of the GAC-SBBR was adjusted from 48 h to 24, 12 and finally 8 h to evaluate the effect of the hydraulic retention time (HRT) on the simultaneous removal of COD and AOX. The COD and AOX removals were in the range of 53–92% and 26–99%, respectively. From this study, it was observed that the longest HRT (48 h) yielded a high removal of COD and AOX, at 92% and 99%, respectively.

Pulp and paper mills generate varieties of pollutants depending upon type of the pulping process being used. This paper presents the characteristics of wastewater from South India Paper Mill, Karnataka, India which is using recycled waste paper as a raw material. The raw wastewater consists of 80-90 mg L( - 1) suspended solid and 1,010-1,015 mg L( - 1) dissolved solid. However, pH varied from 5.5-6.8. The biochemical oxygen demand and chemical oxygen demand ranged from 200-210 and 1,120-1,160 mg L( - 1), respectively. Aerobic treatment of raw effluent attribute to significant reduction in suspended solid (range between 25 to 30 mg L( - 1)) and total dissolved solid (range between 360 to 390 mg L( - 1)). However, pH, temperature, and electrical conductivity were found superior after treatment. Copper, cadmium, iron, lead, nickel, and zinc were found in less quantity in raw effluent and were almost completely removed after treatment. The dendrogram of the effluent quality parameters clearly indicate that South India Paper Mill does not meet Minimal National Standard set by central Pollution Control Board to discharge in agricultural field.

Two pulp and paper industrial wastes, lime mud (LM) and recovery boiler ash (RB), have low moisture contents, low heavy metal contaminations and contain various carbonate compounds which contribute to a high pH. Metal finishing wastewater (MF-WW) has a low pH, high levels of TDS and high contaminations from Cr, Cu, Pb and Zn. The heavy metals from MF-WW were removed by sorption and precipitation mechanisms. LM gave better results in removing heavy metals from MF-WW than RB. At a reaction time of 45min, the maximum removal efficiencies for Cr (93%) and Cu (99%) were obtained at 110gL(-1) of LM, but at 80gL(-1) for Pb (96%) and Zn (99%). Treatment with LM gives a higher sludge volume than with RB. However, the leachability of heavy metals from LM is lower. Leachability of heavy metals in the sediment for all selected treatment conditions is within government standards.

The toxicity of bleached Kraft pulp mill effluents (BKME) is usually attributed to chemical compounds which are produced and released throughout various stages of pulp and paper production. The main objective of the present work was to detect sub-lethal responses of goldfish (Carassius auratus) to secondary treated BKME which was treated with Rhizopus oryzae. A total of 96 carps (C. auratus; 11 +/- 3 g) were exposed to different concentrations of the post-treated effluent (0, 1, 10, 25, 50, and 100%), in 28 days semi-static tests. Several biomarkers were then evaluated to assess the toxicological effects: induction of CYP1A (metabolic processes of organic compounds in liver), change in steroid profiles (11-Ketotestosterone, 17beta-estradiol), histopathology of liver and gonads and somatic indices (GSI, HSI) for endocrine disruption and other physiological disturbances. The most significant results show an induction of CYP1A in both sexes and a decrease of 17beta-estradiol concentrations in females. Histopathological changes such as liver tissue degeneration were observed in fish exposed to 50 and 100% of the BKME. Although the BKME was biologically treated there are some chemical compounds in the effluent that are capable to affect fish physiology, however, a clear evidence for endocrine disruption was not found.

Ecolabeled paper towels are manufactured using post-consumer recycled material and sold in markets using a recycle logo. Environmentally conscious consumers purchase these paper towels and thereby contribute to improving environmental quality. In this paper, we estimate the implicit value placed by consumers on ecolabeled paper towels using a hedonic price function and conduct an expenditure analysis using Heckman's selection model. Using the data set from the Internet-based grocery stores called as Peapod we find that some consumers recognize ecolabels on paper towels and place a substantial, positive price premium on them. The expenditure analysis indicates that for the preferred functional form, the demand for ecolabeled paper towels is inelastic for environmentally conscious consumers. The simulated results from the selection model indicate that a small subsidy for ecolabeled paper towels will not substantially change consumers' purchase decisions.

Agro-based pulp and paper mills in India are one of the most polluting industries; in addition, they are high consumers of raw water. Growing scarcity of high quality freshwater as well as stringent regulatory standards is compelling these units to explore appropriate water management options. Based on data obtained through a questionnaire survey and plant visits, this work provides an overview of the water use and effluent treatment status in Indian agro-residue and recycled pulp and paper mills. The challenges faced by this sector are reviewed and practices adopted by progressive units to minimize freshwater use are illustrated through case studies.

Two PCP-degrading bacterial strains, Bacillus cereus (ITRC-S6) and Serratia marcescens (ITRC-S7) were used for the treatment of pulp and paper mill effluent at conditions; 1.0% glucose and 0.5% peptone at 30 +/- 1 degrees C at 120 rpm for 168 h of incubation. These two bacterial strains effectively reduced colour (45-52%), lignin (30-42%), BOD (40-70%), COD (50-60%), total phenol (32-40%) and PCP (85-90%) within 168 h of incubation. However, the highest reduction in colour (62%), lignin (54%), BOD (70%), COD (90%), total phenol (90%) and PCP (100%) was recorded by mixed culture treatment. The bacterial mechanism for the degradation of pulp and paper mill effluent may be explained by an increase in the cells biomass using added co-substrates resulting liberation of significant amount of chloride due to bacterial dechlorination of chlorolignins and chlorophenols this showed reduction in colour, lignin and toxicity in the effluent. Further, GC-MS analysis of ethyl acetate-extractable compounds from treated pulp paper mill effluent reinforces the bacterium capability for the degradation of lignin and pentachlorophenol, as many aromatic compounds such as 2-chlorophenol, 2, 4, 6-trichlorophenol and tetrachlorohydroquinone, 6-chlorohydroxyquinol and tetrachlorohydroquinone detected which were not present in the untreated effluent.

The bagasse fly ash, obtained from the local sugar industry, has been used as an inexpensive and effective adsorbent for the removal of color from pulp and paper industry. Effect of various operating variables, viz., contact time, initial concentration, adsorbent dose and particle size on the removal of color has been studied and discussed. It is found that for optimum removal of color, contact time for adsorption equilibrium equals to 60 min., at dosage of 2 g/l of baggase fly ash. The material exhibits good removal capacity (86%) and follows both the Langmuir and the Freundlich models.

This article describes a study on the viability of using waste from the paper industry: biomass boiler ash and green liquor dregs to fabricate mortars and concretes. Both types of ash were characterized by obtaining their chemical and mineralogical composition, their organic matter content, granulometry, adsorption and other common tests for construction materials. Seven different mortars were fabricated, one for reference made up of cement, sand, and water, three in which 10, 20, or 30% of the cement was replaced by biomass ash, and three others in which 10, 20, or 30% of the cement was replaced with dregs. Test specimens were fabricated with these mortars to conduct flexural and compression tests. Flexural strength is reduced for all the mortars studied. Compressive strength increases for the mortars fabricated with biomass ash and decreases for the mortar with dregs. Finally, 5 concretes were made, one of them as a reference (neither biomass ash nor dregs added), two of them with replacements of 10 and 20% of biomass ash instead of cement and another two with replacements of 10 and 20% of dregs instead of cement. The compressive and tensile splitting strength increase when a 10% of ash is replaced and decrease in all the other cases. The modulus of elasticity always decreases.

Some Chilean copper slag dumps from the nineteenth century still remain, without a proposed use that encourages recycling and reduces environmental impact. In this paper, the copper slag abandoned in landfills is proposed as a new building material. The slags studied were taken from Playa Negra and Puquios dumps, both located in the region of Atacama in northern Chile. Pozzolanic activity in lime and Portland cement systems, as well as the alkali activation in pastes with copper slag cured at different temperatures, was studied. The reactivity of the slag was measured using thermogravimetric analysis (TGA), scanning electron microscopy (SEM), X-ray diffraction (XRD), electrical conductivity and pH in aqueous suspension and Fourier Transform Infrared Spectroscopy (FTIR). Furthermore, copper slag-Portland cement mortars with the substitution of 25% (by weight) of cement by copper slag and alkali-activated slag mortars cured at 20 and 65 °C were made, to determine the compressive strength. The results indicate that the ancient copper slags studied have interesting binding properties for the construction sector.

Conjugated resin acids (RAs) in fish bile are considered a sensitive chemical indicator of exposure to pulp and paper mill effluent, and were used in this study to monitor the post-spill situation of a lake area (Southern Lake Saimaa) contaminated by black liquor discharged from a mill in June 2003. From the exposure perspective of populations of wild roach and perch, which were studied for their bile RAs at four time periods (July 2003, September 2003, May 2004, July 2004), the exceptional event passed in 2 months or less. Perch had lower concentration of RAs in bile than roach in all sampling areas and all times. Besides the current emissions present in the water column, part of the exposure status of the roach population to RAs seemed to derive from historically contaminated sediments. In order to test this hypothesis, a laboratory experiment with perch and roach, along with three teleosts (rainbow trout, brown trout and whitefish), was conducted. The species were simultaneously exposed for 7 days to RAs (23 microg/l). We calculated a perch/roach-ratio to investigate the difference in origin of exposure between perch and roach populations in the wild and in the laboratory. One year after the spill, the perch/roach-ratio of bile RAs was 0.25 (CV 25%) at 1 km from the mill. This is in contrast to that found under the sole waterborne conditions (0.44; CV 24%), supporting the idea that sediments serve as an additional source of RAs in roach. Additionally, bioconcentration factor log BCF(bile(RA)) was calculated to assess hepatobiliary performance and the capacity to excrete RAs in fish.

India has a large number of paper manufacturing units, with mills varying in size of operations and type of product, scattered all over the length and breadth of the country. Present study deals with the survey of four different pulp and paper mills (Mill A, Mill B, Mill C and Mill D) in India, differing in their scale of operation as well as raw material usage. Physico-chemical characterization of wastewaters produced by different processing units like digestor house liquors, bleaching section, paper machine backwaters, combined inlet to the ETP and outlet to ETP, for all the four mills, was conducted. Different parameters like pH, Color, COD, BOD, percent Na, SAR, TDS and Total hardness were analyzed and compared. Highly significant differences were thus found between all the processing units of all four mills with p values < 0.01. This evaluation showed that though these mills have effluent treatment facilities installed in their premises, improvements are still needed to increase their efficiencies for treating the discharged wastewaters.

Paper industries using different raw materials such as hard wood, bamboo, baggase, rice-straw and waste papers and bleaching chemicals like chlorine, hypochlorite, chlorine dioxide, hydrogen peroxide, sulphite and oxygen were studied to estimate organic pollution load and Adsorbable Organic Halides (AOX) per ton of production. The hard wood based paper industries generate higher Chemical Oxygen Demand (COD) loads (105-182 kg t(-1)) and Biochemical Oxygen Demand (BOD) loads (32.0-72 kg t(-1)) compared to the agro and waste paper based industrial effluents. The bleaching sequences such as C-EP-H-H, C-E-H-H, C-E-Do-D1 and O-Do-EOP-D1 are adopted in the paper industries and the molecular elemental chlorine free bleaching sequence discharges low AOX in the effluent. The range of AOX concentration in the final effluent from the paper industries was 0.08-0.99 kg t(-1) of production. Water consumption was in the range of 100-130 m(3) t(-1) of paper production for wood based industries and 30-50 m(3) for the waste paper based industries. Paper machine effluents are partially recycled after treatment and pulp mill black liquor are subject to chemical recovery after evaporation to reduce the water consumption and the total pollution loads. Hypochlorite bleaching units of textile bleaching processes generate more AOX (17.2-18.3 mg l(-1)) and are consuming more water (45-80 l kg(-1)) whereas alkali peroxide bleaching hardly generates the AOX in the effluents and water consumption was also comparatively less (40 l kg(-1) of yarn/cloth).

At present, there is no reliable method in use that unequivocally describes paper industry material flows and makes it possible to compare geographical regions with each other. A functioning paper industry Material Flow Account (MFA) that uses uniform terminology and standard definitions for terms and structures is necessary. Many of the presently used general level MFAs, which are called frameworks in this article, stress the importance of input and output flows but do not provide a uniform picture of material recycling. Paper industry is an example of a field in which recycling plays a key role. Additionally, terms related to paper industry recycling, such as collection rate, recycling rate, and utilization rate, are not defined uniformly across regions and time. Thus, reliably comparing material recycling activity between geographical regions or calculating any regional summaries is difficult or even impossible. The objective of this study is to give a partial solution to the problem of not having a reliable method in use that unequivocally describes paper industry material flows. This is done by introducing a new material flow framework for paper industry in which the flow and stage structure supports the use of uniform definitions for terms related to paper recycling. This new framework is termed the Detailed Wheel of Fiber.

PubMedID: 26739011 This paper aimed to analyze short-term changes in landscape pattern that primarily results from building development in the east coast of Mersin Province (Turkey). Three sites were selected. Ikonos (2003) and Quickbird (2009) images for these sites were classified, and land cover transformations were quantitatively analyzed using cross-tabulation of classification results. Changes in landscape structure were assessed by comparing the calculated values of area/edge and shape metrics for the earlier and later dates. Area/edge metrics included percentage of land and edge density, while shape metrics included perimeter-area ratio, fractal dimension, and related circumscribing circle (RCC) metrics. Orchards and buildings were dominating land cover classes. Variations in patch edge, size, and shapes were also analyzed and discussed. Degradation of prime agricultural areas due to building development and implications of such development on habitat fragmentation were highlighted. © 2016, Springer International Publishing Switzerland.

Communities across Canada rely heavily on natural resources for their livelihoods. One such community in Pictou County, Nova Scotia, has both benefited and suffered, because of its proximity to a pulp and paper mill (currently owned by Northern Pulp). Since production began in 1967, there have been increasing impacts to the local environment and human health. Environmental reports funded by the mill were reviewed and compared against provincial and federal regulatory compliance standards. Reports contrasted starkly to societal perceptions of local impacts and independent studies. Most environmental monitoring reports funded by the mill indicate some levels of compliance in atmospheric and effluent emissions, but when compliance targets were not met, there was a lack of regulatory enforcement. After decades of local pollution impacts and lack of environmental compliance, corporate social responsibility initiatives need implementing for the mill to maintain its social licence to operate.

The complexity of residual toxic organics from biologically treated effluents of pulp and paper mills is a serious concern. To date, it has been difficult to choose the best treatment technique because each of the available options has advantages and drawbacks. In this study, two different treatment techniques using laboratory-scale aerobic sequencing batch reactors (SBRs) were tested with the same real recycled paper mill effluent to evaluate their treatment efficiencies. Two attached-growth SBRs using granular activated carbon (GAC) with and without additional biomass and a suspended-growth SBR were used in the treatment of real recycled paper mill effluent at a chemical oxygen demand (COD) level in the range of 800–1300 mg/L, a fixed hydraulic retention time of 24 h and a COD:N:P ratio of approximately 100:5:1. The efficiency of this biological treatment process was studied over a 300-day period. The six most important wastewater quality parameters, namely, chemical oxygen demand (COD), turbidity, ammonia (expressed as NH 3 –N), phosphorus (expressed as PO 4 3 –P), colour, and suspended solids (SS), were measured to compare the different treatment techniques. It was determined that these processes were able to almost completely and simultaneously eliminate COD (99%) and turbidity (99%); the removals of NH 3 –N (90–100%), PO 4 3 –P (66–78%), colour (63–91%), and SS (97–99%) were also sufficient. The overall performance results confirmed that an attached-growth SBR system using additional biomass on GAC is a promising configuration for wastewater treatment in terms of performance efficiency and process stability under fluctuations of organic load. Hence, this hybrid system is recommended for the treatment of pulp and paper mill effluents.

Bisphenol A (BPA) is a chemical widely used both in plastics production as a food and beverage container and in thermal papers as a color developer. Dietary consumption is the main route of human exposure to BPA, but dermal absorption through handling different papers might be underestimated or ignored. In this study, BPA in different paper products, including different types of papers, receipts and Chinese currencies, were investigated. BPA was detected in receipts (n = 87) and Chinese currencies (n = 46) with concentrations of 0.17-2.675 × 10(4) μg per g paper and 0.09-288.55 μg per g paper, respectively. Except for parchment papers (n = 3), copy papers (n = 3) and food contact papers (n = 3), BPA was measured in all of the other paper products, with levels of 0.01-6.67 μg per g paper. BPA transferred from thermal papers to common papers increased with the increasing contact pressure. Compared with that in water, the migration speed of BPA was doubled in the synthetic sweat. Washing hands could reduce BPA dermal exposure, and washing hands with lotion was the most efficient way. However, about 19-47% of BPA was still found on hands after different washing methods. Dermal absorption via handling of receipts and papers was estimated to be 36.45 ng per day for the general population and 1.54 × 10(-3) to 248.73 μg per day for a cashier. These values are below the maximum doses recommended by the U.S. Environmental Protection Agency and the European Food Safety Authority. However, due to its uncertain adverse effects on human beings, long-term BPA exposure through dermal absorption should be paid more attention, particularly for some occupational populations.

Uptake properties of Ni2+ were examined for unmilled and milled paper sludge calcined at various temperatures to develop a new usage of waste paper sludge. Since paper sludge mainly consists of cellulose ([C6H(10)O5]n) fibers, calcite (CaCO3), kaolinite (Al2Si2O5(OH)4) and talc (Mg3Si(4)O(10)(OH)2), amorphous and crystalline CaO(MgO)-Al(2)O(3)-SiO(2) compounds are formed by calcining paper sludge. Wet and dry milling treatments were performed to accelerate solid-state reaction to form the above mentioned target compounds. The crystalline phases originally present decompose at increasing calcining temperature (up to 800 degrees C) in the order cellulose

The seasonal physico-chemical and microbial quality of Gola river water has been analyzed after confluence of pulp paper mill waste. The study revealed that it has enhanced 20-30 times pollution load of BOD, COD, TDS, TSS, sulphate, chloride, sodium, nitrate, potassium, lignin and phenol after mixing of pulp paper mill waste with river water in all season. Further, it induced the bacterial growth by increasing most probable number value of E. coli was 1.57 x 10(4), 1.6 x 10(4), 1.37 x 10(4) and SPC count was 1.68 x 10(4), 1.64 x 10(4), 1.67 x 10(4)/100 ml during summer, monsoon, winter respectively. While the most probable number value in river water before mixing of pulp paper mill waste was 1.4 x 10(2), 1.82 x 10(2), 1.5 x 10(2) and SPC count was 2.8 x 10(3), 2.89 x 10(3), 2.78 x 10(3)/100 ml during summer, monsoon and winter respectively. This indicated from 88-114 fold increase in most probable number value of E. coli and 56.55-60.0 times increase in SPC count of river water after mixing of effluent in summer, monsoon and winter. Moreover, the most probable number value in effluent itself before mixing was 3.4 x 10(2), 3.3 x 10(2), 2.8 x 10(2) and SPC count was 6 x 10(4), 6.5 x 10(4), 6 x 10(4)/100 ml during summer, monsoon, winter, respectively. Furthermore, it was revealed that the seasonal variation also regulated the bacterial population dynamics as per the physico-chemical quality, in which E. coli was found highest at the rate of (5.9 x 10(4)), E. aerogenes (5.3 x 10(4)), P. aeruginosa (1.3 x 10(4)), S. aureus (3.2 x 10(3)), K. pneumoniae (2.6 x 10(4)), Enteritidis (1.1 x 10(4)) on monsoon season and V. cholerae (7.4 x 10(2)), V. vulnificus (9.2 x 10(2))/100 ml in river water when contaminated with pulp paper mill waste in monsoon season. Thus, the monsoon season showed presence of FC and TC indicated the thermo-tolerant and disease causing group of bacterial population in effluent and its sequence was observed as monsoon>summer>winter. This indicated the growth of many pathogenic and non-pathogenic bacteria for health hazards with contamination of pulp paper waste in aquatic ecosystem within the vicinity of pulp paper mill industry.

Applications of manures to agricultural fields have increased soil test values for P to high levels in parts of the USA and thus increased the likelihood that P will be transported to surface water and degrade its quality. Waste paper applications to soils with high STP (soil test P) may decrease the risk of P transport to surface water by decreasing DRP (dissolved reactive P) by the formation of insoluble Al–P complexes and providing organic matter to improve infiltration. A field experiment was conducted near Booneville, AR (USA) to assess the effects of different rates of a waste paper product addition on STP, soil bulk density, and total soil C with a soil with approximately 45 mg Bray1-P kg 21 soil (dry weight). A Leadvale silt loam soil (fine-silty, siliceous, thermic Typic Fragiudult) was amended with 0, 22, 44, or 88 Mg waste paper product ha 21 to supply approximately 90, 170, or 350 kg Al ha 21 , respectively. One year after additions, there was a strong negative correlation between waste paper product application rates and soil bulk density, and a strong positive correlation between rates and total soil C content. Soil bulk density and total C 2 yr after additions, and soil DRPand Bray1-P were not affected by waste paper additions. These results support the hypothesis that decreases in DRP in runoff from soils receiving waste paper additions were probably due to changes in soil organic matter and bulk density, rather than changes in the chemical forms of soil P.

Combustion of spent vacuum residue hydrodesulfurization catalyst and incineration of paper sludge were carried out in thermo-gravimetric analyzer and an internally circulating fluidized-bed (ICFB) reactor. From the thermo-gravimetric analyzer-differential thermo-gravimetric curves, the pre-exponential factors and activation energies are determined at the divided temperature regions, and the thermo-gravimetric analysis patterns can be predicted by the kinetic equations. The effects of bed temperature, gas velocity in the draft tube and annulus, solid circulation rate, and waste feed rate on combustion efficiency of the wastes have been determined in an ICFB from the experiments and the model studies. The ICFB combustor exhibits uniform temperature distribution along the bed height with high combustion efficiency (>90%). The combustion efficiency increases with increasing reaction temperature, gas velocity in the annulus region, and solid circulation rate and decreases with increasing waste feed rate and gas velocity in the draft tube. The simulated data from the kinetic equation and the hydrodynamic models predict the experimental data reasonably well.