Search

Membrane separation technology is one of the cost effective and most efficient technologies for treatment of wastewater from textile industry. However, development of membranes with better performance and thermal stability is still a highly challenging task. In this study, successful preparation of a novel thermally stable polyimide (PI) polymer was demonstrated using 2,4,6-trimethyl-1,3-phenylenediamine, 4,4′-diaminodiphenylmethane and 1,2,4,5-benzenetetracarboxylic dianhydride components. PI was selected as representative candidate because of its excellent thermal stability (decomposition temperature of 529 °C), as revealed by thermogravimetric analysis. Furthermore, PI polymer was used to fabricate ultrafiltration (UF) membrane by phase inversion process. This UF membrane is especially interesting as it allowed for almost complete penetration of monovalent (NaCl) and divalent (Na 2 SO 4) inorganic salts because of its molecular weight cut off of 9320 Da. Moreover, the membrane exhibited very good surface hydrophilicity with the water contact angle of 67.6°. This PI-based UF membrane was found to be substantially effective as it showed high pure-water and dye-permeation fluxes of 345.10 and 305.58 L m−2 h−1 at 0.1 MPa, respectively. Besides, the membrane exhibited a rejection of 98.65% toward the direct red 23 dye (100 ppm) at 0.1 MPa. Thus, this PI-based UF membrane is highly beneficial and acts as a potential candidate for dye removal from wastewater produced by textile industry. [ABSTRACT FROM AUTHOR]

A pilot-scale ultrafiltration (UF)–nanofiltration (NF) integrated membrane system (IMS) which included a self-cleaning crossflow UF filtration process and a dual-stage NF process with a capacity of 100 m 3 ·d − 1 NF permeation water was established for seawater softening investigation. The separation performance of the dual-stage NF process under different conditions, such as operating pressure, recovery rate, and inlet flowrate, was extensively investigated; long-term performance and energy consumption of the dual-stage NF process were analyzed as well. The results showed that during the long-term operation, UF could provide qualified filtrate for NF. The dual-stage NF process achieved high separation performance with good permeate quality, especially high rejection of Ca 2 + and Mg 2 + (> 90%). In addition, the dual-stage NF process showed good anti-fouling characteristics, with the normalized NF permeate flux maintaining at an essential constant value of about 14 L·m − 2 ·h − 1 at 3.5 MPa, and DOC rejection around 90% during the long-term experiment. Energy consumption of the dual-stage NF process increased with the increase of the operating pressure and the decrease of the raw seawater temperature, which was about 1.8 kWh·m − 3 at 3.5 MPa and 25 °C. [ABSTRACT FROM AUTHOR]

Membrane fouling is the main problem during the nanofiltration (NF) process of brackish water desalination due to the existence of natural organic matter, especially humic acid (HA). Moreover, the conventional membrane cleaning method would do great harm to the environment because large amount of chemicals were employed. In order to control organic fouling, a novel cleaning method via direct osmosis backwash (DOBW) by injecting high salinity (HS) solution was developed. Different operating conditions for HS-DOBW technology in the actual process were systematically investigated. The results demonstrated that there was a strong driving force to lift and sweep the foulants from the membrane surface which would be carried over to the brine. The optimal conditions in terms of HS (150 kg/m 3 NaCl solution) flow rate of 0.121 L/min were selected for the subsequent experiments. The results showed that the fouling could be almost fully reversible (more than 99.78% permeate water flux recovery), and the membrane needed to be cleaned for about 10 min because of the appearance of HA on membrane surface at the fouling time of 24 h. Most importantly, the HS-DOBW technology is very effective in keeping the membrane continuously clean and ensuring stable permeate production. [ABSTRACT FROM AUTHOR]

Abstract: Flat sheet asymmetric PSf/clay nanocomposite membranes with different clay dosage were prepared by phase inversion method. Dimethyl acetamide was used as a solvent and water was used as a coagulant. PEG 400 was used as a pore forming additive in the casting solution. The morphology and structure of membranes were analyzed by scanning electron microscope, transmission electron microscope and X-ray diffractometer. The performance of membranes was evaluated in terms of pure water flux (PWF), protein rejection, porosity, contact angle, tensile strength and elongation at break respectively. Results showed that clay had a good dispersion in the PSf matrix. The addition of clay additive increased the ratio of large pore in the skin layer and weakened the tensile strength. PWF and porosity of membranes increased with the increase of clay dosage. With increase in clay dosage from 0wt.% to 6wt.%, the PWF increased from 342Lm−2 h−1 to 382Lm−2 h−1. [Copyright &y& Elsevier]

Abstract: Nanofiltration (NF) membranes are playing a more and more important role in brackish and seawater softening process, wastewater reclamation and other industrial separation. In this study, ultrafiltation (UF) and NF (ESNA3, Hydranautics) were assembled to an integrated membrane system (IMS) as pretreatment prior to seawater reverse osmosis (SWRO) to evaluate the NF efficiency of seawater softening. The influences of NF feed property (the feed from UF1 with 100kDa MWCO and UF2 with 20kDa MWCO, respectively), operating pressure (0.5–3.0MPa), cross-flow velocity (0.028–0.048m/s) and feed temperature (5–17°C) on the softening efficiency in terms of the NF flux and ion rejection were investigated. The results showed that the high softening efficiency of NF membrane could be achieved using UF membrane with smaller MWCO (20kDa). NF system using UF2 as pretreatment process yielded a higher flux of 61.4L/(m2 h) with Ca2+, Mg2+, SO4 2− rejection of 44.37%, 73.26% and 99.82%, respectively, under the optimum operating conditions of operating pressure at 1.5MPa, cross-flow velocity at 0.035m/s and feed temperature at 12.5°C. And, the relatively excellent selectivity of divalent ions and univalent ions can be obtained by ESNA3 membrane compared to that of other NF membranes reported in the literature, indicating that the ESNA3 membrane seems to be appropriate for seawater softening process. [Copyright &y& Elsevier]