Search

The micro-discharge effect limits the development of high-frequency microwave power components to miniaturization and integration. Therefore, it has become a focus of research to effectively suppress the micro-discharge effect, increase the micro-discharge threshold, and strengthen the environmental stability of high-frequency microwave devices. In this study, different elemental ratios of carbon (C)/silver (Ag)/titanium (Ti) composite films were obtained by multi-target magnetron co-sputtering technology and then systematically analyzed for micro-discharge effects. When the doping ratio of C/Ag/Ti was 3.538/1/0.013, the corresponding maximum secondary electron emission coefficient (δmax) decreased to 1.01 owing to the suppression of secondary electron emission by the increase in the content of sp2 hybrid bond. The micro-discharge threshold of Ku band waveguide filters coated with moderate C/Ag/Ti composite films showed an optimal performance of 10 000−12 500 W, which was increased by approximately 20 times. Moreover, the microstructure of the composite films exhibited higher density and flatness with a tiny increase in the titanium doping ratio, representing good environmental stability. Thus, the effective suppression of the secondary electron emission yield, significant improvement in the micro-discharge threshold, and enhancement of the environment stability of microwave components could be realized simultaneously by reasonably controlling the content of titanium in silver and titanium co-doped carbon-based composite films. [ABSTRACT FROM AUTHOR]

The micro-discharge effect is a failure mechanism that often appeared in space microwave devices under vacuum conditions, such as RF (radio frequency) cavity, RF satellite missile, and antenna launching communication system. How to control micro-discharge effectively and simply has become a research hotspot. In this paper, we have prepared a series of doping silver (Ag)/carbon (C) composite films by double target magnetron sputtering technology and have significantly reduced the maximum secondary electron emission coefficient (δmax) from 2.522 to 1.04 when the doping ratio of Ag/C is 1.345. Theoretically, the continuous increase of sp2 hybrid bond content tuned by the existing Ag nanoparticles has a greater contribution to the conductivity and inhibition of secondary electron emission in the Ag/C composite films. Meanwhile, the gradually emerged "multi-trap" surface structure with the increase of Ag doping content has further increased the collision between excited secondary electrons and free electrons, achieving an obvious inhibition effect. The results demonstrate that secondary electron emission can be suppressed effectively by tuning the structural feature of two kinds of compounded materials with low δmax. It is of great significance in physical mechanism analysis and design of the new doping process. [ABSTRACT FROM AUTHOR]

The occurrence of passive intermodulation (PIM) is inevitable in high-power microwave devices. It interferes with wireless communication and radar systems, resulting in severe deterioration of receiving performance. So far, narrowband PIM analyzers have been realized for different business bands. However, they are incapable of testing wideband systems. To solve this problem, rack-mounted analyzers piled with multiple narrowband analyzers were implemented. While such solutions significantly increase the volume, cost, and power consumption, they cannot provide a wide, continuous bandwidth for PIM localizations. Aiming to solve this problem, we propose a novel solution for realizing ultrawideband PIM analyzers. Based on the principle of cooperative radio frequency and baseband (RF-BB) nulling, we demonstrate an experimental prototype working within a continuous frequency band covering three octaves, exhibiting promising potential in PIM testing applications. [ABSTRACT FROM AUTHOR]

Many radio frequency measurement systems require multicarrier signals with coherent phases between carriers with different frequencies. A typical example is the signal generator which is used in multicarrier multipactor (MM) testing systems. In this paper, we propose a new approach for the generation of coherent multicarrier signals based on a state-of-the-art phase-locked loops technique. Different from existing systems that rely on a heavy use of commercial microwave instruments, this generator can be implemented with on-shelf chips and devices. As an example, an ultrahigh frequency band generator is implemented and how to implement the in-system calibration of this generator in an experimental multipactor testing system is demonstrated. Based on the proposed approach, performing a quantitative experimental research on MM becomes affordable for an ordinary microwave laboratory, which may promote the in-depth experimental study in this area. It can also be used in a wide range of applications such as MIMO and phased array systems. [ABSTRACT FROM AUTHOR]

Passive intermodulation (PIM) potentially occurs in all high-power passive microwave devices. It can severely deteriorate the receiving performance of wireless communication and radar systems. To date, the simultaneous localization of multiple PIM sources in practical microwave devices is still a technical challenge. In this paper, we indicate that if a reference PIM source can be introduced into the standard PIM testing system, and the amplitude and frequency-dependent phase difference between the reference and the real PIM products can be used to construct a k-space multicarrier signal, PIM localization algorithms for both wideband and narrowband devices can be proposed based on the inverse k-space Fourier transform and inverse optimization of the partial multicarrier signal. Simulation and experimental results validate the effectiveness of the proposed approaches. These methods can solve the difficulty of multipoint PIM localization, and can be widely used in the design, production, testing, and troubleshooting of high-power microwave systems. [ABSTRACT FROM AUTHOR]

The newly discovered “long-term” multicarrier multipactors that can be induced by low-energy electric fields potentially threatens the reliability of spaceborne microwave systems. It also causes a new technical challenge to the prediction of the global occurrence threshold of multicarrier multipactors. In this paper, we propose efficient approaches to rapidly compute the fluctuation of space electrons in the evolving process of a multicarrier multipactor, based on which Monte Carlo approaches are developed to efficiently find the global “worst case” waveforms and the occurrence thresholds for both “single-event” and “long-term” multipactors. The proposed approaches can be used for wideband devices, providing an efficient integrated solution for the multicarrier multipactor analysis for practical high-power microwave devices with inhomogeneous field distribution. [ABSTRACT FROM PUBLISHER]

Terahertz technology is one of the research fronts in the microwave society. Among many technical challenges, achieving high-power terahertz radiation has been attracting many efforts. In this paper, we investigate the possibility of power synthesis at low-end frequencies of the terahertz gap based on discrete sources. We show that by applying precision digital phase control, such a power synthesis can be achieved, overcoming the difficulty of phase alignment at these frequencies. For demonstration, we implement a 110-GHz prototype system employing solid-state impact avalanche and transit time diodes. Using a simulation- and measurement-based design methodology, the impedance matching of the designed cavity is able to be simultaneously obtained at both the RF bias and the 110-GHz frequency without using any absorbing material. Detailed design, simulation, and measurement of the prototype are introduced and the experimental results comply well with analytical expectations. Analysis shows that with increased wide digital bit width, the proposed approach is able to provide sufficient phase control precision, making it possible to be used in the power synthesis applications at low terahertz frequencies. [ABSTRACT FROM AUTHOR]

In nature, most of the surfaces are rough and waveguide flanges are not exception. And these surfaces topography are of high importance in the response of the waveguide flanges connection system. These surfaces topography are usually described by statistical parameters. And statistical parameters depend strongly on the resolution of the roughness‐measuring instrument, and hence the values of statistical parameters are not unique for a surface. As a result, the predictions of passive intermodulation (PIM) level of microwave devices based on these statistical parameters also may not be unique to a pair of contacting surfaces. Fortunately, fractal method is independent on the resolution of the roughness‐measuring instrument. Therefore, the randomness of the rough surface is not affected by the differences in the model. Consequently, if PIM level of rectangular waveguide is predicted with fractal parameters, the predicted value will be unique. Based on this motivation, a new model is developed. In this model, the fractal method is used to characterize the surface topography of waveguide flanges. Then, the third order PIM level of a rectangular waveguide flange is predicted. The analytic results are verified by PIM test set‐up. This work is help to understand PIM phenomenon and design the low‐PIM waveguide. [ABSTRACT FROM AUTHOR]

• Surface engineered Ag/Al substrates by carbon coating for space microwave devices. • K s factor is extracted from the angular-dependent SEY coefficient measurement by using the Vaughan model. • Low-cost, easy-to-scale process is provided to reduce the SEY coefficient by 35%. High power microwave devices have been suffering from secondary electron yield (SEY), which occurs at the surface and leads to increases in energy dissipate and noise level in microwave cavities. The suppression of SEY in microwave materials is significant for space applications. In this work, we report a surface roughness evolution mechanism induced by carbon coating on a widely-used microwave cavity material Ag/Al. The competition between the preferred growth and the island growth modes leads to the roughness enhancement in the 60 nm carbon coated Ag/Al substrates. By extracting the smooth factor K s in Vaughan model from the angular dependent SEY measurement, we attribute the suppression of SEY to the intrinsic low SEY of the carbon film and the high surface roughness. Our work demonstrates a low-cost, easy-to-scale coating process to effectively prevent the formation of secondary electron avalanche in space borne microwave devices. [ABSTRACT FROM AUTHOR]