Search

Dielectric wall accelerators, a class of induction accelerators, employ a novel insulating beam tube to impress a longitudinal electric field on a bunch of charged particles. The surface flashover characteristics of this tube may permit the attainment of accelerating gradients on the order of 100 MV/m for accelerating pulses on the order of a nanosecond in duration. A virtual traveling wave of excitation along the tube is produced at any desired speed by controlling the timing of pulse-generating modules that supply a tangential electric field to the tube wall. Because of the ability to control the speed of this virtual wave, the accelerator is capable of handling any charge-to-mass-ratio particle; hence it can be used for electrons, protons and any ion. The accelerator architectures, key technologies and development challenges will be described.

The Dielectric Wall Accelerator (DWA) offers the potential to produce a high gradient linear accelerator for proton therapy and other applications. The current status of the DWA for proton therapy will be reviewed. Recent progress in SiC photoconductive switch development will be presented. There are serious beam transport challenges in the DWA arising from short pulse excitation of the wall. Solutions to these transport difficulties will be discussed.

A compact accelerator system architecture based on the dielectric wall accelerator (DWA) for medical proton beam therapy has been developed by the Compact Particle Acceleration Corporation (CPAC). The major subsystems are a Radio Frequency Quadrupole (RFQ) injector linac, a pulsed kicker to select the desired proton bunches, and a DWA linear accelerator incorporating a high gradient insulator (HGI) with stacked Blumleins to produce the required acceleration energy. The Blumleins are switched with solid state laser‐driven optical switches integrated into the Blumlein assemblies. Other subsystems include a high power pulsed laser, fiber optic distribution system, electrical charging system, and beam diagnostics. An engineering prototype has been constructed and characterized, and these results will be used within the next three years to develop an extremely compact 150 MeV system capable of modulating energy, beam current, and spot size on a shot‐to‐shot basis. This paper presents the details the engineering prototype, experimental results, and commercialization plans.

The Heavy-Ion Fusion Accelerator Research Program at Lawrence Berkeley Laboratory has proposed building a 10 MeV induction linac systems experiment, ILSE, to investigate accelerator physics and beam manipulations which are needed or desirable for an induction linac driver. This paper describes the experiments proposed for ILSE: transverse beam combining, drift compression, bending of space-charge-dominated beams, final focus, recirculation, and some studies of beam propagation in the environment of the reactor chamber.

An investigation is being made into the feasibility of making a compact proton dielectric wall (DWA) accelerator for medical radiation treatment based on the high gradient insulation (HGI) technology. A small plasma device is used for the proton source. Using only electric focusing fields for transporting and focusing the beam on the patient, the compact DWA proton accelerator system can deliver wide and independent variable ranges of beam currents, energies and spot sizes.

Using the dielectric wall accelerator technology, we are developing a compact induction accelerator system primarily intended for pulsed radiography. Unlike the typical induction accelerator cell that is long compared with its accelerating gap width, the proposed dielectric wall induction accelerator cell is short and its accelerating gap width is comparable with the cell length. In this geometry, the RF modes may be coupled from one cell to the next. We will present recent results of RF modeling of the cells and a prediction of the transverse beam instability on a 2-kA, 8-MeV beam.

The second axis of the dual axial radiography hydrodynamic test (DARHT-II) facility at LANL is currently in the commissioning phase. The beam parameters for the DARHT-II machine will be nominally 17 MeV, 2 kA and 1.6 mus. This makes the DARHT-II downstream system the first system ever designed to transport a high current, high energy and long pulse beam [2]. We will test these physics issues of the downstream transport system on a scaled DARHT-II accelerator with a 7.8-MeV and 950-A beam at LANL before commissioning the machine at its full energy and current. The scaling laws for various physics concerns and the beam parameters selection are discussed in this paper.

The DARHT II accelerator at LANL is preparing a series of preliminary tests at the reduced voltage of 7.8 Me V. The transport hardware between the end of the accelerator and the final target magnet was shipped to LLNL and installed on ETA II. Using the ETA II beam at 5.2 MeV we completed a set of experiments designed reduce start up time on the DARHT II experiments and run the equipment in a configuration adapted to the reduced energy. Results of the beam transport using a reduced energy beam, including the kicker and kicker pulser system will be presented.

DARHT-II, the second axis of the Dual-Axis Radiographic Hydrodynamics Test Facility, is being commissioned. DARHT-II is a linear induction accelerator producing 2-microsecond electron beam pulses at 20 MeV and 2 kA. These 2-microsecond pulses will be chopped into four short pulses to produce time resolved X-ray images. Radiographic application requires the DARHT-II beam to have excellent beam quality, and it is important to study various beam effects that may cause quality degradation of a DARHT-II beam. One of the beam dynamic effects under study is "corkscrew" motion. For corkscrew motion, the beam centroid is deflected off axis due to misalignments of the solenoid magnets. The deflection depends on the beam energy variation, which is expected to vary by plusmn0.5% during the "flat-top" part of a beam pulse. Such chromatic aberration will result in broadening of beam spot size. In this paper, we will report simulation results of our study of corkscrew motion in DARHT-II. Sensitivities of beam spot size to various accelerator parameters and the strategy for minimizing corkscrew motion will be described. Measured magnet misalignment is used in the simulation

These kickers will be used to make fast dipoles and quadrupoles which are driven by sharp risetime pulsers to provide precision beam manipulation for high current kA electron beams. This technology will be used on the 2/sup nd/ axis of the DARHT linac at LANL. It will be used to provide 4 micropulses of pulse width up to 120 nsec. Selected from a 2 /spl mu/sec., 2 kA, 20 MeV macropulse. The fast pulsers will have amplitude modulation capability to compensate for beam-induced steering effects and other slow beam centroid motion to within the bandwidth of the kicker system. Scaling laws derived from theory will be presented along with extensive experimental data obtained on the test bed ETA-II.

As part of the effort to develop a multi-axis electron beam transport system using stripline kicker technology for DARHT II applications, it is necessary to precisely determine the position and extent of long high energy beams (6-40 MeV, 1-4 kA, 2 microseconds) for accurate position control. The kicker positioning system utilizes shot-to-shot adjustments for reduction of relatively slow (

Improvements have been made in the performance of the ETA-II accelerator that allow a nominal 2 kA, 6 MeV beam to be focused to a spot size less that 1 mm in diameter. The improvements include reducing the energy sweep to less than /spl plusmn/0.5% over 40 ns of the pulse using a real time energy diagnostic and improving the magnetic tune of the accelerator to reduce the emittance to 8 cm-mrad. Finally, an automated tuning system (MAESTRO) was run to minimize the time dependent centroid motion (corkscrew) by adjusting the steering dipoles over the focusing solenoids. The corkscrew motion was reduced to less than /spl plusmn/0.5 mm at the output of the accelerator.

The second axis accelerator of the Dual Axis Radiographic Hydrodynamic Test (DARHT-II) facility will produce a 2-kA, 20-MeV, 2-/spl mu/s output electron beam with a design goal of less than 1000 /spl pi/ mm-mrad normalized transverse emittance. In order to meet this goal, both the beam breakup instability (BBU) and transverse "corkscrew" motion (due to chromatic phase advance) must be limited in growth. Using data from recent experimental measurements of the transverse impedance of actual DARHT-II accelerator cells by Briggs et al., we have used the LLNL BREAKUP code to predict BBU and corkscrew growth in DARHT-II. The results suggest that BBU growth should not seriously degrade the final achievable spot size at the x-ray converter, presuming the initial excitation level is of the order 100 microns or smaller. For control of corkscrew growth, a major concern is the number of "tuning" shots needed to utilize effectively the "tuning-V" algorithm. Presuming that the solenoid magnet alignment falls within spec, we believe that possibly as few as 50-100 shots will be necessary to set the dipole corrector magnet currents. We give some specific examples of tune determination for a hypothetical set of alignment errors.

During normal DARHT II operation, the beam exiting the accelerator will be well characterized by its nominal design parameters of 20-MeV, 2000-Amperes, 2-/spl mu/sec-pulse length, and 3 cm-mr unnormalized emittance. Normal operation will have the beam delivered to a beam dump via several DC magnets. A 2-way kicker magnet is used to deflect portions of the beam into the straight ahead beamline leading to either a diagnostic beamline or to the converter target beamline. During start up and or beam development periods, the beam exiting the accelerator may have parameters outside the acceptable range of values for normal operation. The Enge beamline must accommodate this range of unacceptable beam parameters, delivering the entire 80 KiloJoule of beam to the dump even though the energy, emittance, and/or match is outside the nominal design range.

The accelerator on the second-axis of the Dual-Axis Radiographic Hydrodynamic Test (DARHT-II) Facility will generate a 20 MeV, 2-4 kA, 2 /spl mu/s long electron beam with an energy variation /spl les//spl plusmn/0.5%. Four short current pulses with various lengths will be selected out of this 2 /spl mu/s long current pulse and delivered to an X-ray converter target. The DARHT-II radiographic resolution requires these electron pulses to be focused to sub-millimeter spots on bremsstrahlung targets with peak-to-peak transverse beam motion less than a few hundred microns. We have modeled the transverse beam motion, including the beam breakup instability, corkscrew motion, transverse resistive wall instability and beam induced transverse deflection in the kicker system, from the DARHT-II injector exit to the X-ray converter target. Simulations show that the transverse motion at the X-ray converters satisfies the DARHT-II radiographic requirements.

Four short current pulses with various pulse widths and spacing will be delivered to the X-ray converter target on the second-axis of the Dual-Axis Radiographic Hydrodynamic Test (DARHT-II) facility. To ensure that the DARHT-II multi-pulse target will provide enough target material for X-ray production for all four pulses, the target needs either to survive the strike of four electron pulses or to accommodate target replenishment. A distributed target may survive hitting of four electron pulses. For target replenishment, two types of target configurations are being considered: stationary target systems with beam repositioning and dynamic moving target systems. We compare these three target systems and their radiographic performance.

The accelerator for the second axis of the Dual Axis Radiographic Hydrodynamic Test (DARHT) facility will produce a 4-kA, 20-MeV, 2-/spl mu/s output electron beam with a design goal of less than 1000 /spl pi/ mm-mrad normalized transverse emittance and less than 0.5-mm beam centroid motion. In order to meet this goal, the beam transport must have excellent optics and the beam breakup instability (BBU) must be limited in growth. Using a number of simulation codes such as AMOS and BREAKUP, we have modeled the transverse impedances of the DARHT-II accelerator cells and the electron beam response to different transverse excitations such as injector RF noise, magnetic dipole fields arising from the 90-degree bend between the cathode stalk and insulator column, and downstream solenoid alignment errors. The very low Q (/spl sim/2) predicted for the most important TM dipole modes has prompted us to extend the BREAKUP code to be able to use the dipole wakefields calculated by AMOS in addition to the most usual discrete frequency BBU mode model. We present results for the predicted BBU growth and the empirical sensitivity to various machine parameters.