Search

The pulp bleaching process removes or transforms the chromophore groups in the pulp, so that the final product reaches a desired brightness. However, this chemical treatment inevitably results in yield loss. Therefore, the objective of this work was to quantify the yield loss caused during the bleaching of kraft pulp of Pinus radiata delignified with oxygen. The material was submitted to three distinct ECF sequences (D0(EPO)D1D2, D0(EPO)D1P, and Z/EDP). At the end of each bleaching stage, the pulp brightness and the loss of gravimetric yield of the process were determined, and the generated filtrates were collected. From these filtrates, the pollutant load of the effluent was determined by measuring the content of total dissolved solids, the chemical oxygen demand, the concentration of total organic carbon carbon, and the adsorbable organic halogens. Among the whole sequences, the Z/EDP sequence had the lowest gravimetric yield, the highest pollutant load in the collected filtrate, and lowest potential for adsorbable organic halogens generation. There was good correlation between the loss of yield from the bleaching process and the organic load of the generated effluent; and among the techniques studied, the quantification of total organic carbon was the most appropriate method for the indirect quantification of the yield loss during the bleaching process of the studied material.

Stigmasterol is a phytosterol contained in Kraft mill effluent that is able to increase over 100% after aerobic biological treatment. This compound can act as an endocrine disrupter as its structure is similar to that of cholesterol. The aim of this study was to evaluate the removal of stigmasterol from Kraft mill effluents treated by a moving bed biofilm reactor (MBBR) with steroidal metabolite detection. The MBBR was operated for 145 days, with a hydraulic retention time of 2 days. Stigmasterol and steroidal metabolites were detected by gas chromatography with a flame ionization detector during MBBR operation. The results show that the MBBR removed 87.4% of biological oxygen demand (BOD5), 61.5% of chemical oxygen demand (COD), 24.5% of phenol and 31.5% of lignin, expressed in average values. The MBBR system successfully removed 100% of the stigmasterol contained in the influent (33 µg L(-1)) after 5 weeks of operation. In that case, the organic load rate was 0.343 kg COD m(-3) d(-1). Furthermore, different steroidal compounds (e.g., testosterone propionate, stigmast-4-en-3-one, 5α-pregnan-12-one-20α-hydroxy, 5α-pregnane-3,11,20-trione and 3α-hydroxy-5α-androstane-11,17-dione were detected in the Kraft mill effluent as potential products of phytosterol biotransformation.

Biochar microparticles were prepared from three different types of biochar, derived from waste materials, such as pine wood (BC-PW), pig manure (BC-PM) and cardboard (BC-PD) under various pyrolysis conditions. The microparticles were prepared by dry grinding and sequential sieving through various ASTM sieves. Particle size and specific surface area were analyzed using laser particle size analyzer. The particles were further characterized using scanning electron microscope (SEM). The adsorption capacity of each class of adsorbent was determined by methylene blue adsorption tests in comparison with commercially available activated carbon. Experimental results showed that dye adsorption increased with initial concentration of the adsorbate and biochar dosage. Biochar microparticles prepared from different sources exhibited improvement in adsorption capacity (7.8±0.5 mg g(-1) to 25±1.3 mg g(-1)) in comparison with raw biochar and commercially available activated carbon. The adsorption capacity varied with source material and method of production of biochar. The maximum adsorption capacity was 25 mg g(-1) for BC-PM microparticles at 25°C for an adsorbate concentration of 500 mg L(-1) in comparison with 48.30±3.6 mg g(-1) for activated carbon. The equilibrium adsorption data were best described by Langmuir model for BC-PM and BC-PD and Freundlich model for BC-PW.

Pulp and paper mill effluents (PPMEs) have been shown to increase gonad size, cause early maturation, and disrupt hormone functions in native and non-native Chilean fish. In this study, we assessed reproductive (plasma vitellogenin; VTG, gonad development) and metabolic (ethoxyresorufin-. O-deethylase activity; EROD) end points, relative liver size (LSI) and condition factor (K) of juvenile female and male rainbow trout exposed to effluents. Unlike previous studies, which have focus either on the specific effects of effluent on fish in laboratory exposures or biotic population statuses downstream of discharge sites, we simultaneously assessed the impacts of PPMES on trout using two approaches: (1) laboratory exposures of tertiary treated PPME produced from processing Eucalyptus globulus or Pinus radiata; and (2) in situ bioassay downstream of the combined discharge of the same pulp mill. Despite an increase in the average gonadosomatic index (GSI) in exposed fish, no statistical differences in gonad size between exposed and unexposed individuals was detected. However, both female and male fish exposed to effluents showed significantly higher concentrations of plasma VTG, so more in fish exposed to Eucalyptus-based effluent when compared to Pinus PPME. In addition, male fish showed intersex characteristics in all exposure assays (Eucaliptus and Pinus) and, despite the low concentration of effluent in the river (

In this work, we prepare cellulose nanopapers of high mechanical performance and with the electrical conductivity of a semiconductor. Cellulose nanofibers (CNF) from bleached softwood pulp were coated with polypyrrole (PPy) via in situ chemical polymerization, in presence of iron chloride (III) as oxidant agent. The structure and morphology of nanopapers were studied, as well as their thermal, mechanical and conductive properties. Nanopaper from pure CNF exhibited a very high tensile response (224 MPa tensile strength and 14.5 GPa elastic modulus). The addition of up to maximum 20% of polypyrrole gave CNF/PPy nanopapers of high flexibility and still good mechanical properties (94 MPa strength and 8.8 GPa modulus). The electrical conductivity of the resulting CNF/PPy nanopaper was of 5.2 10 −2 S cm −1 , with a specific capacitance of 7.4 F g −1 . The final materials are strong and conductive nanopapers that can find application as biodegradable flexible thin-film transistor (TFT) or as flexible biosensor.

Samples of bleached kraft pine cellulosic pulp, either treated with an enzyme preparation (a Thermomyces lanuginosus xylanase, an Aspergillus sp. cellulase, and a multienzyme preparation NS-22086 containing both these activities) or untreated, were refined in a laboratory PFI mill. The treatment with cellulases contained in the last two preparations significantly improved the pulp’s susceptibility to refining (the target freeness value of 30°SR was achieved in a significantly shorter time), increased water retention value (WRV) and fines contents while the weighted average fiber length was significantly reduced. These changes of pulp parameters caused deterioration of paper strength properties. The treatment with the xylanase, which partially hydrolyzed xylan, small amounts of which are associated with cellulose fibers, only slightly loosened the structure of fibers. These subtle changes positively affected the susceptibility of the pulp to refining (refining energy was significantly reduced) and improved the static strength properties of paper. Thus, the treatment of kraft pulps with xylanases may lead to substantial savings of refining energy without negative effects on paper characteristics.

The goal of this study is to evaluate the feasibility of PHA biosynthesis from kraft mill effluent using the batch system evaluating the biomass origin and C:N relationship influence. To evaluate feasibility, batch assays were carried out. Also, two levels of the BOD 5 :N:P relationship (100:5:1 and 100:1:0.2) and three different sludge origins were considered. Inocula were obtained from activated sludge treatment plants for a) sewage (SAS), b) paper mill (PAS) and c) kraft (KAS). The results show that the maximum Biological Oxygen Demand (BOD 5 ) and Chemical Oxygen Demand (COD) removal was 80.5% and 59.7% respectively using KAS as inoculum. In these assays, kinetics constants were 17.9±3.2 mg L −1 and 46.5±1.2 d −1 for ( K COD ) and (r max ), respectively under a BOD 5 :N:P relationship of 100:5:1. The maximum PHA accumulation was obtained under a BOD 5 :N:P relationship of 100:1:0.2 on the third day of batch assays using PAS sludge with 25.72% of the cells accumulating PHA and on the fifth day in batch using SAS and KAS sludge with 25.85% and 30.40% of cells accumulating PHA, respectively. Yields obtained for the 100:1:0.2 relationships ranged from 0.10–0.14 mg PHA mg −1 COD.

The characterization of food waste (FW) and locally available bulking agents (BA) are a prerequisite to optimizing compost recipes. This study measured the variation in FW characteristics (pH, dry matter (DM), carbon (C), wet bulk density and Total Kjeldahl Nitrogen (TKN)) produced by a restaurant and a community kitchen in downtown Montreal, Canada from May to August 2004. The project also measured the mass of FW produced by another restaurant and a group of 20-48 households, from June to August 2004. Locally available BA (hay, straw, pine wood shavings, cardboard, left over cattle feed and wheat residue pellets) were also characterized to formulate composting recipes based on the FW characteristics observed during a period representative of winter and summer conditions. Residential and restaurant FW characteristics varied significantly over the summer months, although the mass produced remained constant at 0.61 and 0.56 kg capita(-1)day(-1), respectively. In addition, the number of customers served by the restaurant increased by nearly 50% from June to August. The BA with the highest moisture adsorption capacity was found to be the wheat residue pellets, followed by chopped straw. Wheat residue pellets, chopped hay and left over cattle feed all presented a balanced C/N ratio. Wheat residue pellets and wheat straw, chopped hay and cardboard demonstrated neutral pH values. Based on the variable FW characteristics and monthly production rates, the formulation of recipes indicates that compost facilities must be flexible enough to handle seasonal variations of as much as 50% by volume.

To study the possibility of some residues from pulp and paper industry being used as substrates to produce seedlings in containers, three composting experiments were carried out using eucalyptus bark, pine bark and a mixture (60:40, v:v) of pine bark+eucalyptus bark. Biochemical parameters studied were: acid and alkaline phosphatases, lipase (C10), protease, urease, beta-glucosidase and total cellulases. The microbiological populations of total aerobic bacteria, total fungi, actinomycetes, nitrifying bacteria, cellulolytic bacteria and fungi were also evaluated. At the end of the process physicochemical characterization of composts was also performed. Results showed in general that the highest microbiological populations as well as for enzymatic activities occurred during the thermophilic phase (40 degrees C) of the process. On the other hand and according to the physicochemical characteristics of composts pine bark is the most appropriate material to be used in the formulation of substrates to produce plants in containers.

The effect of Fenton's reagent (FR) on surface and dispersion properties of black liquor (BL) was investigated. These properties were compared to those of indulin C (IC), a commercial lignin, and egg lecithin (Le). FR was applied at two different bulk concentrations of H2O2 (160 and 320 mM). At pH 8, a minimum in surface tension for the Fenton treated BL was observed. The dispersant ability of BL, IC and Le in oil-in-water (O/W) emulsions was studied by measuring emulsion stability and drop size. It was found that the surface activity and emulsifying capability of BL were higher than those of IC. The emulsifying capability of Le was improved by the FR treatment at low H2O2 concentration.

Dairy cattle barns are a major source of NH3 emissions to the atmosphere. Previous studies have shown that the bedding material used in the barn can influence the magnitude of NH3 emissions, but little is known about which bedding characteristics are important in this respect. The aims of this study were to assess, at a laboratory scale, the relative importance of the chemical [pH, cation exchange capacity (CEC), C:N] and physical (urine absorbance capacity, bulk density) characteristics of 5 bedding materials (chopped wheat straw, sand, pine shavings, chopped newspaper, chopped corn stalks, and recycled manure solids) on NH3 emissions from dairy cattle urine. Recycled manure solids were the most absorbent of the bedding types (4.2 g of urine/g of bedding), and sand was the least (0.3 g of urine/g of bedding). When beddings were soaked in urine to their absorbance capacities, NH3 emissions over 48 h (expressed as a proportion of the urine N absorbed) were not significantly different among bedding types, despite differences in initial bedding pH, CEC, and C:N. When equal volumes of urine were applied to equal depths of dry bedding, NH3 emissions over 48 h were significantly less from sand and pine shavings (23 and 42% of applied urine N, respectively) than from chopped newspaper, chopped corn stalks, and recycled manure solids (62, 68, and 65% of applied urine N, respectively), whereas emissions from chopped wheat straw (55% applied urine N) only differed significantly from that from sand. Differences in the chemical characteristics of the beddings did not explain differences in emission; NH3 emissions increased linearly with CEC contrary to expectations, and there was no significant relationship with initial bedding pH. The physical characteristics of bedding materials were of more importance, as NH3 emissions increased linearly with absorbance capacity and decreased as the bulk density of the packed beddings increased.

An enzymatic biobleaching sequence (L VA QPO) using a laccase from Trametes villosa in combination with violuric acid (VA) and then followed by a pressurized hydrogen peroxide treatment (PO) was developed and found to give high bleaching properties and meet dissolving pulp requirements: high brightness, low content of hemicellulose, satisfactory pulp reactivity, no significant cellulose degradation manifested by α-cellulose and HPLC, and brightness stability against moist heat ageing. The incorporation of a laccase–mediator system (LMS) to bleach sulphite pulps can be a good alternative to traditional bleaching processes since thermogravimetric analysis (TGA) showed that the laccase treatment prevented the adverse effect of hydrogen peroxide on fibre surface as observed during a conventional hydrogen peroxide bleaching treatment (PO). Although VA exhibited the best results in terms of bleaching properties, the performance of natural mediators, such as p -coumaric acid and syringaldehyde, was discussed in relation to changes in cellulose surface detected by TGA.

A hybrid technique incorporating a wet oxidation stage and secondary fermentation step was used to process Pinus radiata pulp mill effluent sludge. The effect of hydrothermal oxidation at high temperature and pressure on the hydrolysis of constituents of the waste stream was studied. Biochemical acidogenic potential assays were conducted to assess acid production resulting from anaerobic hydrolysis of the wet oxidised hydrolysate under acidogenic conditions. Significant degradation of the lignin, hemicellulose, suspended solids, carbohydrates and extractives were observed with wet oxidation. In contrast, cellulose showed resistance to degradation under the experimental conditions. Extensive degradation of biologically inhibitory compounds by wet oxidation did not show a beneficial impact on the acidogenic or methanogenic potential compared to untreated samples.

Treating ground bagasse or Southern yellow pine in the biodegradable ionic liquid (IL), choline acetate ([Cho][OAc]), at 100 °C for 24 h led to dissolution of hemicellulose and lignin, while leaving the cellulose pulp undissolved, with a 54.3% (bagasse) or 34.3% (pine) reduction in lignin content. The IL solution of the dissolved biopolymers can be separated from the undissolved particles either by addition of water (20 wt% of IL) followed by filtration or by centrifugation. Hemicellulose (19.0 wt% of original bagasse, 10.2 wt% of original pine, containing 14–18 wt% lignin) and lignin (5.0 wt% of original bagasse, 6.0 wt% of original pine) could be subsequently precipitated. The pulp obtained from [Cho][OAc] treatment can be rapidly dissolved in 1-ethyl-3-methylimidazolium acetate (e.g., 17 h for raw bagasse vs. 7 h for pulp), and precipitated as cellulose-rich material (CRM) with a lower lignin content (e.g., 23.6% for raw bagasse vs. 10.6% for CRM).

In order to remove wood extractive compounds from pulp mill sludge and thereby enhancing anaerobic digestibility, samples were subjected to either oxidative hydrothermal treatment (wet oxidation) or non-oxidative hydrothermal treatment (thermal hydrolysis). Treatments were carried out at 220 °C with initial pressure of 20 bar. More than 90% destruction of extractive compounds was observed after 20 min of wet oxidation. Wet oxidation eliminated 95.7% of phenolics, 98.6% fatty acids, 99.8% resin acids and 100% of phytosterols in 120 min. Acetic acid concentration increased by approximately 2 g/l after 120 min of wet oxidation. This has potential for rendering sludge more amenable to anaerobic digestion. In contrast thermal hydrolysis was found to be ineffective in degrading extractive compounds. Wet oxidation is considered to be an effective process for removal of recalcitrant and inhibitive compounds through hydrothermal pre-treatment of pulp mill sludge.

The consumption and food transfer efficiency of two commercially used termite bait materials, southern yellow pine wood and cardboard, and one potential bait material, maize (Zea mays L.) cob, were evaluated for use against the Formosan subterranean termite, Coptotermes formosanus Shiraki (Isoptera: Rhinotermitidae), in the laboratory. In the no-choice test, the consumption of wood and cob was similar and significantly more than cardboard. Tunneling under the food sources was similar. In the two-choice test, the consumption was cobwood, woodcardboard, cob = cardboard, and tunneling under these choices was cob = wood, wood = cardboard, cobcardboard. In the three-choice test, no significant difference was detected in consumption, but tunnels made under the cob were significantly more than wood and cardboard. Nile blue A was used to study food transfer of bait material among termite cohorts. Dyed cardboard, cob, or wood (0.1% Nile blue A) was provided to termites as food. Termites feeding on wood turned blue in significantly greater number at 6 h compared with cardboard and cob, but there was no significant difference after 12 h. Blue termites feeding on different bait materials were then collected and combined with undyed termites. When undyed (white) termites were placed with blue termites and food (wood block), termites turned blue in the same percentage regardless of original bait material fed on. However, when no food was provided (starvation group), the rate of white termites turning blue was dramatic; in dyed wood treatment, significantly more termites turned blue than that of cardboard, although neither were significantly different from cob. Our study is the first to show that, cob, an otherwise waste product of the food and biofuel industry, is as efficient as wood and cardboard as a termite bait matrix.

The main objective of this study is to investigate the thermal profiles of a trailer-scale gasifier in different zones during the course of gasification and also to elaborate on the design, characteristics and performance of the gasification system using different biomass feedstock. The purpose is to emphasize on the effectiveness of distributed power generation systems and demonstrate the feasibility of such gasification systems in real world scenarios, where the lingo-cellulosic biomass resources are widely available and distributed across the board. Experimental data on the thermal profiles with respect to five different zones in the gasifier and a comprehensive thermal-chemical equilibrium model to predict the syngas composition are presented in detail. Four different feedstock-pine wood, horse manure, red oak, and cardboard were evaluated. The effects of C, H, O content variations in the feedstock on the thermal profiles, and the efficiency and viability of the trailer-scale gasifier are also discussed.

The use of coagulation and flocculation for tertiary treatment of pulp and paper mill effluent was investigated, where the evaluation was based on the removal of nitrogen (N), phosphorus (P) and BOD from post-coagulated wastewater. The study was undertaken on laboratory scale aerobic stabilisation basins (ASB). Two post coagulated (alum) wastewaters were studied, where the BOD:N:P ratios were 100:1.3:0.06 and 100:1.3:0.3. These wastewaters were treated in two identical concurrent simulations (A & B). The influent ratio for 'A' was selected representing the composition of actual coagulated Pinus radiata sulfite pulp effluent mixed with paper mill effluent. The input composition for 'B' represented a typical P concentration found in existing pulp and paper mill effluents. Unmodified sludge collected from a mill-pond was added at 4% v/v to each simulation replicating the treatment conditions at full-scale. Similar high percentage removals of BOD and COD occurred after 28 days (two HRTs) which were 94 and 67% respectively for 'A', and 98 and 70% respectively for 'B', where both remained at steady state during the third HRT. A statistical analysis of the data revealed that there was no significant difference in the sample variance of the BOD and COD results. Refereed/Peer-reviewed

International audience; Nitrified leachate may still require an additional bio-denitrification step, which occurs with the addition of often-expensive chemicals as carbon source. This study explores the applicability of low-cost carbon sources such as garden refuse compost and pine bark for the denitrification of high strength landfill leachates. The overall objective is to assess efficiency, kinetics and performance of the substrates in the removal of high nitrate concentrations. Garden refuse and pine bark are currently disposed of in general waste landfills in South Africa, separated from the main waste stream. A secondary objective is to assess the feasibility of re-using green waste as by-product of an integrated waste management system. Denitrification processes in fixed bed reactors were simulated at laboratory scale using anaerobic batch tests and leaching columns packed with immature compost and pine bark. Biologically treated leachate from a Sequencing Batch Reactor (SBR) with nitrate concentrations of 350, 700 and 1100 mgN/l were used for the trials. Preliminary results suggest that, passed the acclimatization step (40 days for both substrates), full denitrification is achieved in 10-20 days for the pine bark and 30-40 days for the compost.

Aim of this study is to investigate the effect of adding sodium borohydride (NaBH4) in kraft pulping. First of all, six kraft cooks were carried out for varying active alkali and sulfidity. Then, kraft methods for K1 and K6 cooks were modified by adding 1, 2 and 3% NaBH4. The results indicated that modifying kraft method (K1) by adding 3% NaBH4 (KB13) resulted in 9.97% (relative percentage) yield increase and 10.1% (relative percentage) kappa reduction. Although the mechanical properties of NaBH4 modified pulps were lower compared to the kraft pulps, NaBH4 modified pulps were much brighter.

Estrogenic activity of kraft pulp mill effluents (P. radiata, E. globulus and mixed -50% E. globulus and 50% P. radiata) was evaluated by the yeast estrogen screen assay. The estrogenic activity values were relatively low, ranking between 1.475 and 0.383 ng/L of EE2 eq. (Estrogenic equivalent of 17 a-ethynylestradiol), where the highest value corresponds to the E. globulus effluent and the lowest value to the P. radiata effluent. Analysis by solid phase extraction (SPE) and gas chromatography—mass spectrometry (GC-MS) of chemical compounds present in all three effluents detected at least five major groups of organic compounds, corresponding to fatty acids, hydrocarbons, phenols, sterols and triterpenes. Comparison of analytical and biological data suggests that sterols could be the cause of the estrogenic activity in the evaluated effluent., This work was partially supported by Fondecyt Grant No. 1070509 and a CONICYT AT 24080124 grant for S. Chamorro’s Ph.D. dissertation. Authors thank Prof. J P Sumpter (GLAXO Research and Development Limited, Brunel University) for providing us the S. cerevisiae recombinant. Authors thank CONICYT- CSIC grant (Folio: 2007-138).

A Moving Bed Bioreactor (MBBR) was operated during 333 days. Two different effluents were fed in six different phases. Phases I and II were fed with effluent where Pinus radiata was used as raw material, while phases III to VI were fed with effluent where Eucalyptus globulus was used as raw material. The HRT was reduced from 85 to 4 h, and the BOD5:N:P ratio (100:5:1, 100:3:1 and 100:1:1) was also simultaneously evaluated as an operation strategy. When MBBR was operated with Pinus radiata influent, the performance presents a high BOD5 removal level (above 95%), although COD removal is below 60%. Most of the recalcitrant COD contained in the effluent has a molecular weight higher than 10,000 Da. When MBBR was operated with Eucalyptus globulus influent, the performance is around 97.9-97.6% and 68.6-65.1% for BOD5 and COD, respectively (with HRT up to 17 h). In the Pinus radiata and Eucalyptus globus effluents, the color was mainly found in the molecular weight fraction up to 10,000 Daltons.

WOS: 000253250900001 PubMed: 17531474 The aim of this work was to study the effect of adding PS, AQ and NaBH4 into kraft pulping with special attention given to NaBH4. Kraft, kraft-AQ, PS, and kraft-NaBH4 Pulps were produced under the same cooking conditions and the pulps produced were compared in terms of pulp and paper properties. Kraft method was modified by adding 0.1% AQ, 4% PS and 2% and 4% NaBH4 and the resultant pulps displayed an increase in pulp yield and reduction in both kappa number and screening rejects. On the other hand, there observed an increase in both pulp yield and kappa number when the kraft was modified to PS method. The benefits of NaBH4 addition into kraft pulping was a significant reduction in kappa number and screening rejects and a significant increase in pulp yield. The most notable outcome of NaBH4 was 66.6% increase in pulp brightness when 4% NaBH4 was added into kraft pulping. Of unrefined pulps, unrefined kraft pulp displayed the highest strength of pulp, which is described as tear index at a constant tensile index. Of refined pulps, kraft-AQ showed the highest pulp strength when refined to 6000 and 12,000 revs in PFI mill. (c) 2007 Elsevier Ltd. All rights reserved.

The pulp and paper industry has invested heavily over recent years in cleaner processing, to reduce losses and minimise its impact on the environment. Over the past fifteen years, a New Zealand integrated bleached kraft mill has undergone a comprehensive programme of upgrades to increase production, reduce water consumption and streamline its biological treatment process. Whilst the overall discharge of contaminants from the site decreased, the treatment system performance did not show a concurrent improvement as may have been expected. Reduced BOD removal, low dissolved oxygen levels, and poor solids settlability were symptomatic of phosphorus limitation in the aerated lagoon treatment system. The wastewater entering the system was found to be phosphorus limited at a BOD:P ratio of 100:0.2. Mono-ammonium-phosphate was supplemented, at approximately 30 kg P/d, to raise the phosphorus levels to a BOD:P ratio of 100:0.3. Treatment efficiencies improved very quickly after phosphorus dosage, with a 50% reduction in BOD and TSS discharge, a significant increase in dissolved oxygen levels, and improved BOD removal (85% to 93%). This case study demonstrates that whilst more closed operation can result in reduced discharge of organic loads, there may be negative impacts on the availability of nutrients for balanced biological growth.

Pitch deposit is one of the most troublesome problems for the paper mills in South China that use the masson pine as a raw material to make paper. The triglyceride has been identified as the main composition accounting for pitch problem. in order to set down effective pitch control scheme, the triglyceride content in papermaking process must be measured quantitatively. A method to measure the content of triglyceride in masson wood pulp was developed based on UV spectrophotometer in the present work. The UV spectrogram and characteristic peak location of standard glycerol trioleate as well as the effect of measuring time on absorbency were discussed. The results showed that at 412 nm the relation between absorbency and consistency of glycerol trioleate was linear and the pertinent coefficient reached 0. 971 in the range of reagent dosage and consistency in this experiment. The absorbency decreased linearly with measuring time and the pertinent coefficient reached 0. 990 2. The results of reproductive experiment showed that the recoveries were 98%-104%0 and the accuracy was 1. 27%-4. 03% for the samples in consistency 1. 25-0. 50 g x L(-1). With this method, the content of triglyceride in hexane extractive of masson TMP and acid SP were measured respectively. The degradative effect of triglyceride before and after enzyme treatment for masson wood pulp was also evaluated. The results showed that the triglyceride content was relatively high, about 50% both in the total extractive of masson TMP and acid SP. After enzyme treatment, the content of triglyceride in masson TMP and acid SP was reduced by 46. 31% and 35. 55% respectively.