Search

Reed valves are a type of check valve commonly found in a wide range of applications including air compressors, internal combustion engines, musical instruments, and even the human heart. While reed valves have been studied extensively in these applications, published research on the modeling and application of reed valves in hydraulic systems is sparse. Because the spring and mass components of a reed valve are contained in a single element, it is light and compact compared to traditional disk, poppet, or ball style check valves. These advantages make reed valves promising for use in high-frequency applications such as piston pumps, switch-mode hydraulics, and digital hydraulics. Furthermore, the small size and fast response of reed valves provide an opportunity to design pumps capable of operating at higher speeds and with lower dead volumes, thus increasing efficiency and power density. In this paper, a modeling technique for reed valves is presented and validated in a hydraulic piston pump test bed. Excellent agreement between modeled and experimentally measured reed valve opening is demonstrated. Across the range of experimental conditions, the model predicts the pump delivery with an error typically less than 1% with a maximum error of 2.2%. [ABSTRACT FROM AUTHOR]

Switch-mode hydraulic control is a compact and theoretically efficient alternative to throttling valve control or variable displacement pump control. However, a significant source of energy loss in switch-mode circuits is due to throttling during valve transitions. Hydraulic soft switching was previously proposed as a method of reducing the throttling energy loss, by absorbing, in a small variable volume chamber, the flow that would normally be throttled across the transitioning high-speed valve. An active locking mechanism was previously proposed that overcomes the main challenge with soft switching, which is a lock mechanism that releases quickly and with precise timing. This prior work demonstrated a reduction in energy losses by 66% compared to a control circuit. In this paper, a numerical model is developed for a switch-mode virtually variable displacement pump (VVDP) circuit, utilizing the proposed soft switch. The model is then used as a means of designing a proof of concept prototype to validate the model. The prototype design includes methods for controlling the soft switch spring preload, travel distance, piston displacement required to unlock the soft switch, valve command duty cycle, switching cycle period, and load pressure. Testing demonstrated that the soft switch circuit performed as expected in a baseline condition. The operating region for this prototype was found to be quite narrow. However, the model does a good job of predicting the displacement of the soft switch. [ABSTRACT FROM AUTHOR]

Switched inertance hydraulic systems (SIHS) use inductive, capacitive, and switching elements to boost or "buck" (reduce) a pressure from a source to a load in an ideally lossless manner. Real SIHS circuits suffer a variety of energy losses, with throttling of flow during transitions of the high-speed valve resulting in as much as 44% of overall losses. These throttling energy losses can be mitigated by applying the analog of zero-voltage-switching, a soft switching strategy, adopted from power electronics. In the soft switching circuit, the flow that would otherwise be throttled across the transitioning valve is stored in a capacitive element and bypassed through check valves in parallel with the switching valves. To evaluate the effectiveness of soft switching in a boost converter SIHS, a lumped parameter model was constructed. Simulation demonstrates that soft switching improves the efficiency of the modeled circuit by 42% at peak load power and extends the power delivery capabilities by 77%. [ABSTRACT FROM AUTHOR]

Abstract: Hydraulic accumulators are used in a variety of applications to minimize the pressure variation in hydraulic circuits and to store energy. Conventional hydraulic accumulators suffer from two major limitations, the hydraulic system pressure varies with the quantity of energy stored and the energy density is significantly lower than other energy domains. In this paper, a novel hydraulic accumulator is presented that uses a piston with an area that varies with stroke to maintain a constant hydraulic system pressure while the gas pressure changes. The variable area piston is sealed with a fabric reinforced rolling diaphragm. In this work, the piston radius profile is developed as a function of the piston displacement and then transformed into a function of the axial contact location between the piston and the diaphragm. The piston profile was solved numerically for a variety of conditions using both transformation methods to illustrate the geometric design trade-offs. Using a variable area gas piston with a fixed cylinder area, the maximum gas volume ratio was 1.8:1. An analysis of the energy density revealed that the constant pressure accumulator provides a 16% improvement in energy density over a conventional accumulator at a volume ratio of 2.71:1 and also exceeds the maximum energy density of a conventional accumulator at the lower volume ratio of 1.8:1. This new promising technology maintains a constant hydraulic system pressure independent of the quantity of energy stored, easing system control and allowing other circuit components to be downsized to meet the same power requirements, while also increases the energy storage density. [Copyright &y& Elsevier]

Two laser transmission welding experiments involving polyvinyl chloride are presented that aim to validate a previously presented welding model while helping to further understand the relationship between welding parameters and weld quality. While numerous previous research papers have presented the results of laser welding experiments, there exists minimal work validating models of the welding process. The first experiment explores the interaction of laser power and welding velocity while the second experiment explores the influence of clamping pressure. Using the weld width as the primary model output, the agreement between the welding experiments and the model have an average error of 5.6%. This finding strongly supports the validity of the model presented in Part I of this two paper set (Van de Ven and Erdman, 2007, ASME J. Manuf. Sci. Eng., 129, pp. 849-858). Additional information was gained regarding the operating window for laser transmission welding and the thermal decomposition of polyvinyl chloride. Clamping pressure was found to provide a small, but not statistically significant, influence on the visual appearance, weld width, and weld strength. [ABSTRACT FROM AUTHOR]

This paper discusses the development of a model of laser transmission welding that can be used as an analytical design tool. Currently the majority of laser transmission welding (LTW) applications rely on trial and error to develop appropriate process parameters. A more rigorous design approach is not commonly used primarily due to the complexity of laser welding, where small material or process parameter changes can greatly affect the weld quality. The model developed in this paper also enables optimizing operating parameters while providing monetary and time saving benefits. The model is created from first principles of heat transfer and utilizes contact conduction that is a function of temperature and pressure, Gaussian laser distribution, and many material properties that vary with temperature including the absorption coefficient. The model is demonstrated through a design example of a joint between two polyvinyl chloride parts. The model is then validated with samples welded with a diode laser system using the operating parameters developed in a design example. Using the weld width as the primary output, the error between the model and the experimental results is 4.3%, demonstrating the accuracy of the model. [ABSTRACT FROM AUTHOR]

A challenge in realizing switch-mode hydraulic circuits is the need for a high-speed valve with fast transition time and high switching frequency. The work presented includes the design and modeling of a suitable valve and experimental demonstration of the prototype in a hydraulic boost converter. The design consists of two spools driven by crank-sliders, designed for 120 Hz maximum switching frequency at a flow rate of 22.7 lpm. The fully open throttling loss is designed for <2% of the rated pressure of 34.5 MPa. The transition time is less than 5% (0.42 ms at 120 Hz) of the total cycle and the duty cycle is adjustable from 0 to 1. Leakage and viscous friction losses in the design are less than 2% of the rated hydraulic energy per cycle. The experimental results agreed well with the model resulting in a 3% variation in transition time. The use of the high-speed valve in a pressure boosts converter demonstrated boost ratio capabilities of 1.08-2.06. [ABSTRACT FROM AUTHOR]