Search

In this article, the influence of polishing orientation on surface charge accumulation and flashover characteristics of the basin spacer in a downsized dc-gas insulated transmission line (GIL) are explored by experiments. Results show that the surface charge distribution of the polished spacers is different from the untreated one. Heteropolar charges can be observed in the polished area and outward expansion area under prestressing condition. The flashover voltages of all polished spacers are decreased. The radial polishing (RP) has the greatest impact on the flashover voltage, and the flashover voltage of the radially polished spacer is decreased by 11% under positive prestressing condition. The metal dust adsorptions of the spacers are also measured, which shows that the radially polished spacer is easier to absorb metal dust and the metal dust diffuses in the radial direction. SEM and energy spectrum scanning of different spacers show that there are more exposed alumina particles on the surface of the polished area. The microdischarge induced by alumina particles is the source of heteropolar charges. When the polished area of the spacers is repaired with epoxy paint, heteropolar charges disappear on the surface of the repaired spacer. It is confirmed that charge accumulation and flashover along the spacer surface are mainly affected by the change of surface morphology on the polished area. [ABSTRACT FROM AUTHOR]

In this study, a downsized direct current (dc)-gas-insulated transmission line (GIL) model is applied to investigate the surface charging and discharging characteristics of the basin-type spacer in 0.1-MPa SF6 and air. Under a low electric field, the surface charge accumulation is dominated by the bulk conduction of the spacer. As the charging voltage increases, gas ionization occurs in the localized strong electric field, taking over the dominant position. In 0.1-MPa SF6 gas, flashovers typically develop along the convex surface of the spacer under both positive and negative voltages because the homo-charge accumulation induced by brush discharges on the concave surface aggravates the electric field distortion at the convex side. In air, the dc flashovers have the polarity effect. Under the negative voltage, the flashover development is similar to that in SF6 gas. But for positive polarity, the space charge region of positive polarity intensifies the electric field ahead of the corona region, thus promoting the air-gap breakdown at the concave side of the spacer. [ABSTRACT FROM AUTHOR]

An engineering approach to the computational prediction of surface charging during dielectric tests of medium voltage devices is presented. It is based on a formulation of the saturation charge boundary condition applied to an iteratively estimated area on the insulation surface. The simulation procedure is explained for a simple case study including a rod electrode, shaped barrier, and grounded enclosure. Applications of this procedure to 3-D models of medium voltage devices are presented. [ABSTRACT FROM AUTHOR]

Surface charge accumulation on polymer insulating material has been recognized as an important factor for electric field distortion that results in reduction of surface flashover voltage. This paper reports on the charge accumulation behavior between a pair of finger-shaped electrodes on epoxy/Al2O3 nanocomposites under dc voltage superimposed by repetitive pulses. The charge distribution was measured by means of an electrostatic voltmeter, from which the average charge density could be calculated. Effects of dc voltage, nanofiller content, and pulse voltage on charge accumulation behavior were investigated. Obtained results showed that with the increase in the filler content from 0 wt% to 5 wt%, the average charge density increased initially then appeared to decrease. The superposition of repetitive pulses on dc voltage led to a remarkable growth in charge accumulation as compared with that when only dc voltage was applied. It is suggested that the charges are originated from local gaseous ionization and/or electrode injection, which is determined by the combined voltage. The charge density is dependent upon the surface trap, which is affected by nanofiller content. The superposition of repetitive pulse is considered as a possible reason to encourage local gaseous ionization that results in enhanced accumulation of surface charge. [ABSTRACT FROM AUTHOR]

Charge generation at the interfaces of gas-insulated switchgear or gas-insulated lines is mostly studied from a macroscopic point of view. Integral current measurements are a common method to determine the average inception field strengths and intensities of micro discharges. However, because of the lack of spatial resolution and measurement sensitivity, these experiments do not provide deeper insights on the microscopic processes. By applying surface potential measurement techniques, studying the charge generation of single interface protrusions and drawing conclusions relative to their spatial distribution have become possible. This paper presents a spatially resolved analysis of charge-generation processes at rough aluminum electrodes and insulating interfaces. The results reveal a highly inhomogeneous charge generation at the interfaces even for electric fields below 6 kV/mm. Analyzing the charge generation from a macroscopic perspective has been demonstrated to possibly underestimate the local charge generation by up to three orders of magnitude. Using sulfur hexafluoride (SF6) as the insulation gas at 0.45 MPa and Al2O3-filled epoxy resin insulators, the inception field strength for charge generation at the insulating interface is measured to be 3 kV/mm. For a technical insulation system that includes both a rough aluminum electrode and an insulating interface, significant discharge intensities are observed at a 5-kV/mm electric field. From these results, micro discharges are expected to be highly relevant for dimensioning of gas-insulated devices. [ABSTRACT FROM AUTHOR]

Surface charge accumulation of polymer insulating materials is harmful to the safe operation of electrical equipment, especially under DC electric field excitation. In order to ensure the safety and stable operation of HVDC power system such as Gas-insulated transmission line, it is necessary to understand the influence of the surface charge on the flashover and improve the surface charge dynamic characteristics. In this paper, Epoxy resin (EP) is deposited by SiOx thin films with different plasma treatment conditions. The flashover voltages are measured with and without surface charges. The results show that the flashover occurs at lower voltage due to the accumulated charges on the EP surface. In particular, the surface charge with the same polarity of flashover discharge can reduce the surface flashover voltage significantly. Moreover, the charge decay rate is increased up to 90% by plasma treatment of 3 min, corresponding flashover voltage is increased. In addition, the flashover voltages of samples during the surface charge dissipation are obtained. Both static impact index I and dynamic impact index S are introduced to estimate effect of surface charge on dielectric surface flashover. [ABSTRACT FROM AUTHOR]

The established theories behind low-field ion-drift currents assume that the charge generation from natural ionization is the main source of the charge-carriers, and that it defines the current flowing through the insulation gas in gas-insulated direct current (DC) devices. This charge generation is assumed to be independent of the applied electric field in the cases where the electric field is sufficiently below the onset of microdischarges at the interfaces. However, the results of a few previous studies have suggested the presence of a field-dependent current contribution from some conduction processes, which might significantly accelerate the decay of the surface charges distributed on the insulator surfaces. In this paper, an extensive study on low-field charge transport is presented, and the influences of the insulation volume, electric field, and gas pressure on low-field charge transport are discussed. In accordance with the common structure employed in gas-insulated devices, Al2O3-filled epoxy resin is used in the solid parts of the device and sulfur hexafluoride (SF6) is used for gaseous insulation. At electric fields of approximately 1800 V/m, a gas current that is up to 30 times higher, when compared to the conduction currents caused by the charge generation from natural ionization, is observed. This enhanced current reveals a further conduction process acting in a limited range of low electric fields and is characterized to be independent of the applied voltage polarity. With an increase in the gas pressure, the current amplitude is found to increase linearly and higher electric field is required to reach its maximum. At electric fields below 200 V/m, the conduction current reverses its pressure dependency and increases with decreasing gas pressure. The reported findings strongly indicate that the enhanced low-field charge transport in gasinsulated devices may be owing to electrophoretic conduction. [ABSTRACT FROM AUTHOR]

Polyimide (PI) films have excellent electrical, mechanical and thermal properties in aspect of resisting corona, aging and radiation. However, the pulse voltage combined with dc voltage often causes concentration of local electrical field, which makes the surface charge behaviors more complex and threatens the system. As a means of surface treatment, direct fluorination has been proved as an effective way to improve the polymer properties, without compositing the bulk characteristics. Therefore, this paper intends to reveal the effects of fluorination on surface charge coupling behaviors of the PI films under dc and pulse voltage combination. The PI samples fluorinated for 0, 15, 45 and 60 min were obtained. Surface corona discharging was stressed under the combination of dc and pulse voltage. The surface charge accumulation, decay and distribution were measured coupled with an analysis of trap distribution. The results show the surface charge dynamic behaviors are strongly correlated with the fluorination time, pulse voltage amplitude and polarities of the dc and pulse voltage combination. The trap distribution results imply that the effect of fluorination and charging condition attribute to the change of trap depth and amount. Besides, surface charge behaviors are greatly improved by appropriate fluorination. [ABSTRACT FROM AUTHOR]

As one kind of the basic insulating materials, polyimide has been widely used in turn to turn insulation and turn to ground insulation in inverter-fed motors. However, the pulse voltage from the converter often causes overvoltage and localized high electrical field in the insulation system. During applying the pulse voltage, charges accumulate on the surface of the insulator, which could affect the dielectric property and cause the breakdown of insulation. Direct fluorination is a method to modify the surface layer of the polymers without changing the bulk properties. As a result of the fluorination, hydrogen atoms are replaced by the fluorine atoms and the component of the polymer surface is changed, which can influence the surface charge accumulation and affect the electrical properties. The experiment in this paper was focused on the effect of pulse duration and pulse number on surface charge of the polyimide films. The polyimide films with the fluorination time of 0, 15, 45 and 60 min were prepared. Surface charging was performed by corona discharging using repetitive pulse power at the temperature of 20 °C with the relative humidity of ~15%. The repetition frequency was 1 kHz and the pulse duration was 50, 110 and 210 μs, respectively. The surface charge decay was measured using a specific probe coupled with an electrostatic voltmeter. The results showed that the surface charge increases with increasing the pulse number and the duration of the microsecond pulse. [ABSTRACT FROM AUTHOR]

As one of the basic insulating materials, polyimide films have been widely used in turn to turn insulation and turn to ground insulation in wind turbine generators. However, the pulse voltage from the converter often causes overvoltage and localized high electrical field in the insulation system. Surface charge could affect the dielectric property and cause the breakdown of insulation. Direct fluorination is a method to modify the surface layer of the polymers without changing the bulk properties. As a result of the fluorination, hydrogen atoms are replaced by the fluorine atoms and the component of the polymer surface is changed, which can influence the surface charge accumulation and affect the electrical properties. The experiment in this paper was focused on the effect of direct fluorination on surface charge of polyimide films under pulse voltage. The polyimide films with the fluorination time of 15, 30, 45 and 60 min were prepared, together with the unfluorinated one as a comparison. Surface charging was performed by corona discharging using repetitive pulse power at the temperature of 25 °C with the relative humidity of ~45%. The rising time of the pulse was 25 μs and the frequency was set at 200, 400, 600 and 1000 Hz, respectively. The surface charge decay was measured using a specific probe coupled with an electrostatic voltmeter. The results showed that the surface charge behavior was affected by the fluorination, corona discharging time, pulse voltage amplitude and frequency. [ABSTRACT FROM PUBLISHER]

Silicone rubber (SiR), as a basic insulating material, is widely used in insulators for HVDC transmission lines. The prominent characteristics of the SiR coating are the hydrophobicity and the hydrophobicity recovery, which can suppress the development of leakage currents and dry-band discharges, and prevent the flashover incidents. Fluorination is a method to change the chemical component of the surface layer of polymers, which could induce the corresponding change in hydrophobicity and some electrical properties, thus influencing the dc surface flashover characteristics. Room temperature vulcanized (RTV) SiR samples were fluorinated in a stainless reaction vessel at about 298K (25°C) using a F2/N2 mixture with 12% F2 by volume and 0.05 MPa (500 mbar) for respectively 5, 10, 15 and 20 minutes. The hydrophobicity of samples with different fluorination time was measured by the static contact angle tests after corona aging. The variation of hydrophobicity with the lapse of time was recorded. Dc flashover tests in different conditions were carried out between two plane electrodes on top of the material sample. The flashover voltage was found to be associated with the surface hydrophobicity status of samples. Obtained results showed the effects of the fluorination on the surface charge, hydrophobicity performance and dc flashover voltage. It is suggested that the appropriate fluorination can improve surface hydrophobicity and suppress surface charge accumulation, thus raising the dc flashover voltage. [ABSTRACT FROM AUTHOR]

Polymeric insulating materials exposed to pulse voltage with a nanosecond rise time in pulsed power have drawn increasing attention. Surface charge accumulation and decay on the charged polymers are very important parameters related to discharge. Nanocomposite technology has been used to improve the electrical properties of polymeric insulating materials. Therefore, it must be confirmed whether the nanosecond rise time of pulse voltage on the dynamic behaviour of surface charge on polymeric nanocomposites is different from that without nanoparticles. In this paper, we attempted to clarify the effect of the rise time on the electrical properties of epoxy/TiO2 nanocomposites focusing on surface charge accumulation and decay. Samples were prepared by dispersing nano-scale TiO2 particles into epoxy (EX) by mixing with shear force. Corona charging tests were performed at room temperature with a relative humidity of ~ 40%. The charge distribution was measured by means of an electrostatic voltmeter. The results show that the rise time plays an important role in the accumulating charge as well as the charge decay rate and varies with the concentration of nanoparticles and charge polarity. It is suggested that charge dynamics are dependent upon the rise time. [ABSTRACT FROM AUTHOR]

It seems generally accepted that HVDC technology is to become increasingly relevant in power systems. With this expected future advance of HVDC, the use of gas insulated switchgear or lines for dc application are getting increasingly interesting. As in the case of dc the electric fields are determined resistively in contrast to the capacitive fields in the case of ac, gas insulated technology has to be revisited. In many previous works surface charging of model spacers was investigated. However, the ion flow problem to properly account for the electric conduction in the gas has not yet been solved. Further, no combination with inhomogeneous electric conductivity determined for example by temperature profiles from ohmic heating in nominal condition has been performed so far. In this paper, the gas conductivity arising from ions produced by natural radiation is computed by solving the ion flow field problem, and its role is compared to spacer bulk conductivities. Further, the impact of temperature profiles on spacer charging is investigated. The results indicate that for actual disc spacers, the spacer bulk conductivity is more important than that from the gas ionized by natural radiation. Especially in the case of polarity reversal, thermally enhanced spacer charging can result in considerable increase of tangential field strengths. [ABSTRACT FROM PUBLISHER]