Search

Switching ripple communication (SRC), which modulates the PWM carrier with digital data and takes the switching ripple as a signal carrier, helps power electronic converters to transfer digital data along with power. This article discusses the theory and implementation of SRC technology. It proves that the modulation using square wave and sinusoidal wave carriers is compatible. The fundamental principles of frequency hopping–differential phase shift keying (FH–DPSK) modulation are then analyzed in detail, and an improved FH–DPSK scheme is proposed to suppress output voltage disturbances, thereby maintaining power quality, reducing communication noise, and separating power control and data modulation. Furthermore, to evaluate the reliability of the communication technique, the effect of power conversion on communication is discussed in detail. Finally, a buck converter with a switching frequency of 100/83.3 kHz is set up, and the experiment achieves a 16.7 kbps bit rate using quaternary modulation, demonstrating the correctness of the scheme. [ABSTRACT FROM AUTHOR]

Following the continuous development of wide bandgap (WBG) devices and multilevel converter technology, medium voltage active front ends are becoming promising in future high-power-density and high-power applications. However, the cost issue is one of the major drawbacks, which stops the WBG devices from being widely applied in high-power areas. This article proposes a silicon carbide (SiC) and silicon (Si) hybrid five-level unidirectional rectifier. It requires only four SiC MOSFETs with relatively low blocking voltage and four Si diodes. Meanwhile, by adding snubber capacitors, all the Si devices are with low-speed switching, and the voltage stresses of fast SiC MOSFETs are minimized. In this article, operational analysis and carrier-based phase-disposition pulsewidth modulation scheme for this circuit are discussed in detail. The capacitor voltage balancing and unity power factor are both realized. Simulation and scaled-down experimental results are demonstrated to verify the proposed rectifier. Furthermore, the comparison of the hybrid five-level rectifiers is given to show the advantages of the proposed rectifier in terms of voltage stress, efficiency, and cost. [ABSTRACT FROM AUTHOR]

In this article, the output voltage control strategy of modular multilevel resonant dc converters (MMRDC) for medium-voltage wide-input-range applications is studied. First, the feasibility and influence of the switching frequency regulation and modulation index regulation are investigated in detail. It is found that the switching frequency choice has a significant effect on the voltage stress of arm inductors and the transformer. Then, based on these considerations, the modulation index regulation plus switching frequency regulation based design and control optimization is proposed. With the proposed design and control method, the switching frequency range for adapting to a wide input range is further reduced, especially under light load operating conditions. Besides, the high voltage stress on arm inductors is avoided and the high voltage dv/dt on the transformer is also eliminated. Finally, a laboratory prototype with 8–16 kV input and 375 V/60 kW output has been built and the experimental validation under a wide input range has been done. The efficiency over 96.4% under the wide input range proved the effectiveness of the optimized control methods. [ABSTRACT FROM AUTHOR]

The modularity of a modular multilevel dc converter (MMDC) makes it attractive for medium-voltage distribution systems. Inherent balance of submodule (SM) capacitor voltages is considered as an ideal property, which avoids a complex sorting process based on many measurements thereby reducing costs and enhancing reliability. This article extends the inherent balance concept previously shown for square-wave modulation to a multilevel version for MMDCs. A switching duty matrix dU is introduced: it is a circulant matrix of preset multilevel switching patterns with multiple stages and multiple durations. Inherent voltage balance is ensured with a full-rank dU. Circulant matrix theory shows that this is equivalent to a simplified common factor criterion. A nonfull rank dU causes clusters of SM voltage rather than a single common value, with the clusters indicated by the kernel of the matrix. A generalized coprime criterion is developed into several deductions that serve as practical guidance for design of multilevel circulant modulation. The theoretical development is verified through full-scale simulations and downscaled experiments. The effectiveness of the proposed circulant modulation in achieving SM voltage balance in an MMDC is demonstrated. [ABSTRACT FROM AUTHOR]

This work presents a 48-1V dc–dc converter with an on-chip switch and gallium nitride (GaN) hybrid power conversion. By series connecting a 12-level Dickson switched-capacitor with a two-phase switched-inductor circuit, the capacitors take over most of the 48-V voltage stresses. The circuit, thus, reduces to an equivalent 4-1V converter, making the on-chip 5-V transistor applicable for a 48-V high-voltage design. Due to the easy integration of on-chip switches and superior switch figures of merit over other 48-1V counterparts, this proposed design is able to achieve the highest switching frequency, the lowest external switch count, and the improved power density compared with other prior-state-of-the-arts. The prototype was fabricated using a 0.18- $\mu \text{m}$ BCD process with an evaluation board volume of 17 mm $\times $ 15 mm $\times $ 2.6 mm. The converter achieves a maximum 8-A loading capacity with the input range from 36 to 60 V and the output from 0.5 to 1 V. The measured peak power efficiency is 90.2%, and the power density is 998 A/in3 considering the power stage volume. [ABSTRACT FROM AUTHOR]

DC transformers based on power electronics are key items of equipment for medium voltage dc (MVDC) distribution systems. Both high and low step-ratio dc–dc conversions are required to interface dc links at different voltages to form an integrated dc distribution system. The transformer-coupled resonant modular multilevel dc–dc converter (RMMC) is well-suited to high step-ratio connection between an MVDC network and a low voltage dc network but it is not suitable in low step-ratio conversion for linking two MVDC networks with similar but not identical voltages. This article presents a circuit evolution of the high step-ratio transformer-coupled RMMC into its low step-ratio transformer-less RMMC counterpart. These two RMMCs share the same structure and the same resonant process within the resonant submodule stack giving rise to the same operational advantages. Also, the circuit design experience can be readily transferred from one to the other. From these two base RMMC circuits, a family of RMMCs with further configurations is elaborated that provide a wider variety of connection options for MVDC distribution systems. In this circuit family, each high step-ratio transformer-coupled RMMC has a low step-ratio transformer-less RMMC counterpart and one can be transformed into the other via the circuit evolution process presented. The theoretical analysis for both high and low step-ratio RMMCs has been verified through full-scale simulations of medium voltage examples and further verified through down-scaled experiments on laboratory prototypes. [ABSTRACT FROM AUTHOR]

The crosstalk voltage on the gate-source terminal of SiC power mosfets in a phase-leg circuit is composed of the gate–drain capacitor introduced voltage and the common-source inductor introduced voltage. The mathematical model of the crosstalk voltage indicates that to suppress two types of crosstalk voltage, there exists a contradictory requirement on the off-state gate loop impedance. This challenge reduces the effectiveness of conventional crosstalk elimination methods. As an improvement, a crosstalk voltage suppression circuit that synchronously eliminates the crosstalk voltage of gate–drain capacitance and the common-source inductance is proposed. In this article, instead of creating low-impedance gate loop in the off-state, a high-impedance gate loop is formatted to eliminate the voltage drop on the common-source inductance. Meanwhile, the potential false turn-on or the negative voltage spikes caused by gate–drain capacitance is eliminated by the precharge voltage in the gate-source capacitor. The required prestored charge is analyzed considering the nonlinear behavior of the junction capacitance of the SiC mosfets. The proposed gate driver is experimentally verified in different switching conditions. [ABSTRACT FROM AUTHOR]

Three-phase current reconstruction techniques with a single current sensor have been studied for permanent magnet synchronous machines (PMSMs) drive system due to its reducing cost and volume. In order to minimize the current reconstruction dead zone in the conventional method with a single dc-link current sensor, a strategy to couple multiple available positions through the single current sensor is proposed in this paper. With the proposed method, two independent equations of the stator currents can be obtained by sampling the single current sensor twice in both zero voltage vectors and active voltage vectors. By solving these two equations, the phase current reconstruction can be achieved accurately, which moves the current reconstruction dead zone toward six corner area of the space vector hexagon. Meanwhile, in order to guarantee the proposed method suitable in the whole linear modulation region, the suitable selection of the pulsewidth modulation switching period is analyzed in detail. Furthermore, the optimal selections of multiple sampling positions are discussed to lower the actual implementation difficulty of the proposed method. Finally, the experimental results on the PMSM demonstrate that the reconstructed phase currents with the proposed method can be always in consistent with the actual measured currents under different working conditions. [ABSTRACT FROM AUTHOR]

Three-phase transformerless multilevel converters are widely used in the high-voltage photovoltaic power generation systems because of their low total harmonic distortion, high power density, and high conversion efficiency. One three-level flying capacitor converter and dual T-type three-level circuits can be combined to derive the compact and cost-effective nested five-level converter. However, due to the lack of an isolation transformer, the common-mode current is generated to degrade the converter performance. First, the common-mode equivalent circuit model of the nested five-level converter is initially derived to further explore its common-mode current generation mechanism. Then, the zero common-mode space vector modulation (ZCM-SVM) is proposed to reduce the common-mode current, which chooses the specific zero common-mode voltage space vectors to synthesize the reference vector. Then, an advanced coordinate transformation is introduced to realize the flexible sector selection and reduce the complexity of the vector action time calculation. The proposed modulation achieves the common-mode current suppression with high dc bus voltage utilization. Finally, the effectiveness of the proposed ZCM-SVM strategy is verified by simulation and experimental results. [ABSTRACT FROM AUTHOR]

Linear ramp slope compensation (LRC) and quadratic slope compensation (QSC) are commonly implemented in peak-current-mode-controlled dc–dc converters in order to minimize subharmonic and chaotic oscillations. Both compensating schemes rely on the linearized state-space averaged model (LSSA) of the converter. The LSSA ignores the impact that switching actions have on the stability of converters. In order to include switching events, the nonlinear analysis method based on the Monodromy matrix was introduced to describe a complete-cycle stability. Analyses on analog-controlled dc–dc converters applying this method show that system stability is strongly dependent on the change of the derivative of the slope at the time of switching instant. However, in a mixed-signal-controlled system, the digitalization effect contributes differently to system stability. This paper shows a full complete-cycle stability analysis using this nonlinear analysis method, which is applied to a mixed-signal-controlled converter. Through this analysis, a generalized equation is derived that reveals for the first time the real boundary stability limits for LRC and QSC. Furthermore, this generalized equation allows the design of a new compensating scheme, which is able to increase system stability. The proposed scheme is called polynomial curve slope compensation (PCSC) and it is demonstrated that PCSC increases the stable margin by 30% compared to LRC and 20% to QSC. This outcome is proved experimentally by using an interleaved dc–dc converter that is built for this work. [ABSTRACT FROM AUTHOR]

Three-level converters typically feature low switching loss and small filter size. In order to realize a high-power-density design for three-level converters, SiC MOSFETs may be selected instead of using Si insulated-gate bipolar transistors. However, all-SiC-MOSFET-based converters suffer from extremely high total cost. In this paper, a SiC MOSFET and Si device hybrid active neutral-point-clamped (ANPC) converter is proposed. It consists of four Si active switches and only two SiC MOSFETs. Thus, it has lower total cost compared to the all-SiC-MOSFET-based ANPC converter. Furthermore, a dedicated modulation scheme is proposed to completely move all the switching events from Si devices to SiC MOSFETs by using redundant switching states. As a result, the switching losses are significantly reduced and extremely high efficiency is achieved. The proposed converter has fully utilized the low-switching-loss advantage of SiC MOSFETs and the low-cost advantage of Si devices, which shows significant superiority in high-end grid-connected inverter and rectifier applications. [ABSTRACT FROM AUTHOR]

Multilevel converters are widely employed in the 30–50 kW medium-voltage grid-connected photovoltaic (PV) generation systems due to their higher power quality and lower switching losses compared with the two-level converters. Dual T-type three-level converters and one three-level diode neutral point clamped circuit can be integrated to derive a simplified five-level modular composited converter (5L-MCC) for the medium-voltage PV grid-connected systems. However, realizing the capacitor voltage balance is a challenge to enhance its reliability. First, the model of dc capacitor voltage variation of the 5L-MCC is discussed to expose a limitation once the nearest three-vector synthesis method is employed with conventional space vector modulation (SVM). In order to extend the operational range, a hybrid space vector modulation (HSVM) strategy is proposed, which integrates the optimized SVM switching sequence for the low-modulation ($M\,< \,0.5$ ) and a simplified vector synthesis method for the high-modulation region ( $M\geq 0.5$). The proposed hybrid modulation maintains the dc capacitor voltage balance over the full modulation range and power factor. Finally, the effectiveness of the proposed HSVM strategy is verified with the simulation and experimental results. [ABSTRACT FROM PUBLISHER]

Switched reluctance motor (SRM) drives are one competitive technology for traction motor drives. This paper proposes a novel and flexible SRM fault-tolerant topology with fault diagnosis, fault tolerance, and advanced control functions. The converter is composed of a single-phase bridge and a relay network, based on the traditional asymmetrical half-bridge driving topology. When the SRM-driving system is subjected to fault conditions including open-circuit and short-circuit faults, the proposed converter starts its fault-diagnosis procedure to locate the fault. Based on the relay network, the faulty part can be bypassed by the single-phase bridge arm, while the single-phase bridge arm and the healthy part of the converter can form a fault-tolerant topology to sustain the driving operation. A fault-tolerant control strategy is developed to decrease the influence of the fault. Furthermore, the proposed fault-tolerant strategy can be applied to three-phase 12/8 SRM and four-phase 8/6 SRM. Simulation results in MATLAB/Simulink and experiments on a three-phase 12/8 SRM and a four-phase 8/6 SRM validate the effectiveness of the proposed strategy, which may have significant economic implications in traction drive systems. [ABSTRACT FROM AUTHOR]

An advanced hybrid LLC series resonant converter with integrated flying-capacitor cell is proposed in this paper to enable the high step-down conversion in the high input voltage applications. The inherent flying-capacitor branch in the primary side can effectively halve the primary switch voltage stress compared with the half-bridge LLC converters. And the input voltage can be shared equally and automatically between the two series half-bridge modules without additional balance circuit or control strategies due to the built-in flying-capacitor cell. Moreover, the inherent soft switching performance during wide load range that exists in the LLC converters is still kept to reduce the switching losses, which ensures the high efficiency. Besides, the proposed converter can be extended to further decrease the switch voltage stress by employing stacked connection. Finally, a 500 ∼ 640 V-input 48 V-output 1 kW prototype is built and tested to verify the effectiveness of the proposed converter. The results prove that the proposed converter is an excellent candidate for the high input voltage and high step-down dc/dc conversion systems. [ABSTRACT FROM PUBLISHER]

The dc symmetrical component method is introduced for the analysis and control of bipolar dc distribution systems under asymmetrical operation. This method is an extension of the classical symmetrical component theory in three-phase ac power systems. The asymmetrical voltage and current in the positive and negative poles are decomposed into symmetrical components in common and differential modes. The equivalent circuit for each mode is derived, which forms decoupled mode networks. Consequently, it allows for independent investigation of each mode, and provides an insightful view of the static and dynamic behavior of a bipolar dc power system. The dc symmetrical component method is a general approach which is applicable to different aspects of system design. As an example, an enhanced common-mode voltage regulation scheme is described. It suppresses common-mode LC resonance by adding active damping control, and reduces common-mode impedance to improve power quality and voltage stability. The major theoretical conclusions are verified by experimental results. [ABSTRACT FROM AUTHOR]

Single-phase voltage source transformerless inverters have been developed for many years and have been successful commercial applications in the distributed photovoltaic (PV) grid-connected systems. Moreover, many advanced industrial topologies and recent innovations have been published in the last few years. The objective of this paper is to classify and review these recent contributions to establish the present state of the art and trends of the transformerless inverters. This can provide a comprehensive and insightful overview of this technology. First, the generation mechanism of leakage current is investigated to divide the transformerless inverters into asymmetrical inductor-based and symmetrical inductor-based groups. Then, the concepts of dc-based and ac-based decoupling networks are proposed to not only cover the published symmetrical inductor-based topologies but also offer an innovative strategy to derive advanced inverters. Furthermore, the transformation principle between the dc-based and ac-based topologies is explored to make a clear picture on the general law and framework for the recent advances and future trend in this area. Finally, a family of clamped highly efficient and reliable inverter concept transformerless inverters is derived and tested to offer some excellent candidates for next-generation high-efficiency and cost-effective PV grid-tie inverters. [ABSTRACT FROM PUBLISHER]

In this paper, a soft-switching dc/dc converter with secondary-side phase-shift control strategy is proposed to improve the conversion efficiency and minimize the primary switch voltage stress in the high input voltage applications. Zero-voltage-switching performance is achieved for both the primary- and secondary-side power devices in a wide load range to reduce the switching losses due to the secondary-side phase-shift control scheme. Furthermore, compared with the conventional phase-shift control mechanism, the circulating current at the freewheeling stage is effectively suppressed as well to minimize the conduction losses. Moreover, the voltage stress of the primary switches is only half of the input voltage by employing the improved three-level structure, which makes the low-voltage rated power devices available to improve the circuit performance. In addition, the converter can work in the buck, balance, and boost modes to achieve a relatively wide input voltage range, which is an expected advantage for the communication power system to minimize the electrolytic capacitors with an acceptable hold-up time. The operation principle is analyzed and experimental results of a 1-kW 100-kHz prototype are provided to verify the effectiveness and the advantages of the proposed converter. [ABSTRACT FROM AUTHOR]

In this paper, an isolated series asymmetrical half-bridge converter (SA-HBC) is proposed to satisfy the high power and high input-voltage requirements. In the proposed converter, two half-bridge modules with series configuration are adopted in the primary side to reduce the switch voltage stress to half of the input voltage. Moreover, the series half-bridge cells share the same transformer and leakage inductance, which simplifies the circuit structure. Zero-voltage-switching transition is achieved for all the active switches by employing the asymmetrical control scheme to reduce the switching losses. Furthermore, the voltages of the input capacitors are automatically balanced without any additional components or complex control methods. In addition, a family of dc–dc converters with series half-bridge structure is explored to give a universal discussion and extensive applications of the proposed contributions for the high input-voltage systems. Finally, a 500–600-V input 48-V output 1-kW prototype operating with 100 kHz switching frequency is built and tested to demonstrate the effectiveness of the proposed SA-HBC converter. The efficiency of 95% at full load is realized. [ABSTRACT FROM AUTHOR]

An advanced symmetrical voltage quadrupler rectifier (SVQR) is derived in this paper to serve as the secondary rectification topology, which helps to extend the converter voltage gain and reduce the output diode voltage stresses. The output voltage is four times of the conventional full-bridge voltage rectifier with the same transformer ratio, which benefits to reduce the turns ratio of the transformer and decrease the parasitic parameters. Also, low voltage-rated diodes with high switching performance can be applied to improve the efficiency. Meanwhile, all the diodes in SVQR have the same voltage and current stresses, which simplifies the thermal design. Furthermore, two output electrolytic capacitors are connected in series to share the high output voltage, and the voltage balance can be realized naturally without any additional voltage-sharing scheme. A clear picture is made in this paper to give a general framework and universal applications for the derived SVQRs for high step-up and high output voltage conversion systems. A dual boost converter is used as an example to demonstrate the clear advantages of the derived SVQRs. [ABSTRACT FROM AUTHOR]

In order to eliminate the common-mode (CM) leakage current in the transformerless photovoltaic (PV) systems, the concept of the virtual dc bus is proposed in this paper. By connecting the grid neutral line directly to the negative pole of the dc bus, the stray capacitance between the PV panels and the ground is bypassed. As a result, the CM ground leakage current can be suppressed completely. Meanwhile, the virtual dc bus is created to provide the negative voltage level for the negative ac grid current generation. Consequently, the required dc bus voltage is still the same as that of the full-bridge inverter. Based on this concept, a novel transformerless inverter topology is derived, in which the virtual dc bus is realized with the switched capacitor technology. It consists of only five power switches, two capacitors, and a single filter inductor. Therefore, the power electronics cost can be curtailed. This advanced topology can be modulated with the unipolar sinusoidal pulse width modulation (SPWM) and the double frequency SPWM to reduce the output current ripple. As a result, a smaller filter inductor can be used to reduce the size and magnetic losses. The advantageous circuit performances of the proposed transformerless topology are analyzed in detail, with the results verified by a 500-W prototype. [ABSTRACT FROM AUTHOR]

First, the limitations of the conventional interleaved boost converters in high-step-up and high-output-voltage applications are addressed in this paper. Then, a general derivation law of the nonisolated converters from their isolated counterparts is proposed and studied to give a universal solution for high-performance topology deduction. By employing the direct energy transfer concept, a family of nonisolated high-step-up interleaved boost converters is originated to make the turns ratio of a built-in transformer as another design freedom for the voltage gain extension. The derived converters have the advantages of large voltage conversion ratio, low power switch voltage stress, small input current ripple, and zero-voltage-switching soft-switching performance. The steady-state operation of the derived converter is analyzed, and the circuit performance is summarized to explore its advantages in the high-step-up, high-output-voltage, and large-current conversion systems. Finally, a 1-kW prototype with 40-V input and 380-V output voltages is implemented and tested to show the effectiveness of the derived converters. One of the main contributions of this paper is that a clear picture is made on the universal derivation law to generate high-step-up and high-performance dc/dc converters. [ABSTRACT FROM PUBLISHER]

A novel isolated zero-voltage-transition (ZVT) boost converter with coupled inductors is proposed in this paper to satisfy the high power, high step-up, and isolated requirements. In the proposed converter, the input-parallel configuration is adopted to share the large input current and to reduce the conduction losses, while the output-series structure is employed to double the output voltage gain. Consequently, a transformer with a low turns ratio can be applied, which makes the transformer design and optimize easily. Moreover, the active clamp circuits are employed to reduce the switch voltage stress and to recycle the energy stored in the leakage inductance. The ZVT is achieved during the whole switching transition for all the active switches, so the switching losses can be reduced greatly. Furthermore, the diode reverse-recovery problem is partly solved due to the leakage inductance. In addition, the magnetic integration technology is applied to improve the efficiency and to reduce the magnetic component size. Finally, a 48-V input 380-V output 1-kW prototype operating with 100-kHz switching frequency is built and tested to demonstrate the effectiveness of the proposed converter. [ABSTRACT FROM PUBLISHER]

In this paper, a voltage multiplier cell is inserted in the conventional boost converter operated in continuous conduction mode (CCM) to provide another design freedom for the voltage-gain extension. Thus, the voltage conversion ratio is enlarged and the narrow turn-OFF period is avoided in the high step-up applications. Furthermore, the voltage multiplier cell makes the voltage stress of all the power devices lower than the high output voltage. As a result, the low-voltage-rated power devices can be employed to reduce the conduction losses and to improve the power device reliability. Moreover, zero-voltage switching soft-switching operation is achieved for the power MOSFETs in the whole-switching transition. Zero-current switching turn-OFF condition is provided for the diodes. Therefore, the power device switching losses and the diode reverse-recovery losses are minimized greatly. In addition, the input current ripple is reduced due to the CCM operation compared with most of the published single-stage single-phase high step-up converters, which makes it more advantageous in the hybrid electric vehicles and the fuel-cell power conversion systems. Finally, the experimental results from a 500-W, 36–380-V prototype are provided to validate the effectiveness of the proposed converter. [ABSTRACT FROM PUBLISHER]