Search

Formaldehyde removal from an air stream absorbed into a water stream in a packed bed continuously and then removed by employing a combination of UV and ferrate(VI) as a highly-powerful oxidant in a continuous stirred tank. In addition, the removal of formaldehyde from water was investigated in both batch and continuous modes. The results of the study performed on formaldehyde-contaminated water treatment can be used for both air and water treatment process design. The primary objective of this study is to compare the performance of using UV and ferrate(VI) individually with that of using UV/ferrate(VI) simultaneously to remove formaldehyde from both air and water. Moreover, the effects of several factors such as pH, ferrate(VI) concentration and temperature on formaldehyde removal from water using ferrate(VI) method were evaluated. The results of the current study in batch condition showed that the best initial pH and ferrate(VI) concentration to obtain the highest formaldehyde removal are 2 and 1 mg/l, respectively. The results of this part of research also reveal that temperatures rise from 25 °C to 50 °C increases formaldehyde removal from 69% to 97%; however, further increase in temperature has an adverse effect on removal efficiency. The combination of UV and ferrate(VI) enhances formaldehyde removal efficiency to very close to 100% within 35 min. In continuous air stream treatment, maximum formaldehyde removal of 94% was obtained by using a packed bed scrubber with gas over liquid flow rates ratio of 1.28 m 3 /m 3 . Although the results of this study shows that ferrate(VI) method for removal of formaldehyde can be considered as a promising alternative for both water and air treatment, further economic studies are required for this process to be commercialized., (Copyright © 2016 Elsevier Ltd. All rights reserved.)

Odorous gases are the most important reason that people register complaints with organizations responsible for wastewater collection and treatment systems (WCTS). Although several studies have been conducted for prevention and control of odorous gases, no comprehensive research exists about recent achievements in this area. The aim of the present study is to collect and categorize the new achievements in preventing and controlling odorous gases in WCTS. Two strategies for controlling odor emissions from WCTS are (1) prevention of odor production and (2) removal of odorous compounds from emissions of WCTS. Between the two, priority goes to preventing odorous compounds' production. Several methods have been developed to prevent odor production, such as increasing oxidation reduction potential; inhibiting the activity of sulfide reducing bacteria; chemical removal of hydrogen sulfide; applying formaldehyde and paraformaldehyde to prevent hydrogen sulfide production; and using fuel cells in hydrogen sulfide inhibition and gradual release of oxygen in gas phase by using MgO2 or CaO2. In addition to preventing odorous compounds in WCTS, many other methods have been introduced to remove odorous compounds from emissions of WCTS, such as biofilters; bioscrubbers; biotrickling filters; suspended growth reactors; and membrane bioreactors and scrubbers. Through this review, responsible organizations can find new, effective, and economical strategies to prevent and control odorous gases in WCTS., (Copyright © 2016 Elsevier Ltd. All rights reserved.)

Removal efficiency of gold from a solution of pure tetrachloroaurate ions was investigated using microbial fuel cell (MFC) technology. The effects of type of catholyte solution and initial gold concentration on the removal efficiency were considered. Due to its presence at high levels in the gold wastewater, the effect of copper ions on the removal efficiency of the gold ions was also studied. The effects of pH and initial biomass concentration on the gold removal efficiency was also determined. The results showed that after 5 h contact time, 95% of gold removal efficiency from a wastewater containing 250 ppm of initial gold ions at ambient temperature using 80 g/L yeast concentration was achieved. After 48 h of the cell's operation under the same condition, 98.86% of AuCl4– ions were successfully removed from the solution. At initial gold concentration in the waste solution of 250 ppm, pH 2, and initial yeast concentration of 80 g/L, 100% removal efficiency of the gold was achieved. On the other hand, the most suitable condition for copper removal was found at a pH of 5.2, where 53% removal efficiency from the waste solution was accomplished. [ABSTRACT FROM AUTHOR]