Search

As wind power technology points to increase power ratings, the implementation based on a permanent-magnet synchronous generator (PMSG) with a full-power converter is expanding its market share. Multilevel converters, as for example, neutral-point clamped (NPC) converters, are therefore well suited for this application. Predictive current control presents similar dynamic response and reference tracking than other well-established control methods, but working at lower switching frequencies, and providing extensive flexibility to apply either online or offline different control laws to the same plant. In this work, the predictive current control is applied to both sides of the back-to-back NPC converter connecting a permanent-magnet synchronous wind power generator to the grid. DC-link neutral-point balance is achieved by means of the predictive control algorithm, which considers the redundant switching states of the back-to-back NPC converter. Reduced number of commutations, current spectrum control, and compliance with the low-voltage ride-through (LVRT) requirement are carried out with the predictive control. The obtained experimental results confirm the suitability of the proposed control approach. [ABSTRACT FROM PUBLISHER]

Detailed switching models of power electronics devices often lead to long computing times, limiting the size of the system to be simulated. This drawback is especially important when the goal is to implement the model in a real-time simulation platform. An alternative is to use dynamic average models (DAM) for analyzing the dynamic behavior of power electronic devices. This paper presents the development of a DAM for a bidirectional solid-state transformer and its implementation in a real-time simulation platform. Several case studies have been carried out in order to evaluate the behavior of the model under different operating conditions, check its feasibility for power quality improvements and explore the implementation in a real-time simulation platform. [ABSTRACT FROM AUTHOR]

Highlights: [•] Development of a time-domain model for a high-frequency solid state transformer. [•] Control strategy for bidirectional power flow control. [•] A voltage oriented control (VOC) scheme is used for the high-voltage side stage used to ensure constant dc bus voltage, unity power factor condition at the input terminal in an average sense, and no ripple in the input active power. [•] Several test cases are presented to illustrate the features of the proposed device. [ABSTRACT FROM AUTHOR]

The increasing installed wind power capacity has caused wind power generation to become a significant percentage of the entire electric power generation. As a consequence, the power system operators have included wind power plants regulation to improve the control of the overall power system, both in steady-state and transient operation. Therefore, wind power systems are required to verify the grid connection requirements stated by the power system operators. In presence of grid voltage dips, the low voltage ride-through (LVRT) requirement compliance produces a mismatch between the generated active power and the active power delivered to the grid. The conventional solution assumes that the active power surplus is dissipated in a dc-link resistor. In this paper, a control scheme for the back-to-back neutral-point-clamped converter is proposed. Under grid voltage dip, the controllers for generator-side and grid-side converters work concurrently to meet the LVRT requirement by storing the active power surplus in the turbine-generator mechanical system inertia while keeping constant the dc-link voltage. Simulation and experimental results verify the proposed control scheme. [ABSTRACT FROM PUBLISHER]

A novel noninverting boost–buck dc–dc converter topology is presented, applicable when both sides of the converter need to have the same grounding. It is based on the back-to-back connection of two n-level active-clamped or diode-clamped converter legs, and allows bidirectional power flow. A simplified topology is proposed for unidirectional power flow applications. Two new pulse width modulation strategies with different advantages are proposed to operate the converter guaranteeing dc-link capacitor voltage balance in every switching cycle for all possible operating conditions and using small capacitance values. The semiconductor device losses are compared through analysis, simulation, and experiments to the losses in a conventional two-level boost–buck converter. The analysis yields a higher efficiency for the multilevel converter, especially as the number of levels increases. Experimental results are presented to validate the good converter performance in four- and five-level converter prototypes. [ABSTRACT FROM AUTHOR]

This paper presents the definition of the virtual vectors for the general case of an n-level two-leg diode-clamped converter, suggests guidelines for designing virtual-vector pulsewidth modulation (PWM) strategies, and provides the mathematical expressions of the leg duty-ratio waveforms corresponding to this family of PWMs. Modulations defined upon these vectors guarantee the dc-link capacitor voltage balance in every switching cycle under any type of load and enable the use of these topologies with passive front ends. The performance of these multilevel converters operated with the proposed PWMs is compared to the performance of alternative designs through analysis, simulation, and experiments. [ABSTRACT FROM AUTHOR]

Low-voltage ride-through (LVRT) requirements demand wind-power plants to remain connected to the network in presence of grid-voltage dips. Most dips present positive-, negative-, and zero-sequence components. Hence, regulators based on symmetrical components are well suited to control gridconnected converters. A neutral-point-clamped topology has been considered as an active front end of a distributed power-generation system, following the trend of increasing power and voltage levels in wind-power systems. Three different current controllers based on symmetrical components and linear quadratic regulator have been considered. The performance of each controller is evaluated on LVRT requirement fulfillment, grid-current balancing, maximum grid-current value control, and oscillating power flow. Simulation and experimental results show that all three controllers meet LVRT requirements, although different system performance is found for each control approach. Therefore, controller selection depends on the system constraints and the type of preferred performance features. [ABSTRACT FROM AUTHOR]

Abstract-In the previous literature, the introduction of the virtual-space-vector (VV) concept for the three-level, three-leg neutral-point-clamped converter has led to the definition of pulsewidth modulation (PWM) strategies, guaranteeing a dc-link capacitor voltage balance in every switching cycle under any type of load, with the only requirement being that the addition of the three phase currents equals zero. This paper presents the definition of the VVs for the general case of an n-level converter, suggests guidelines for designing VV PWM strategies, and provides the expressions of the leg duty-ratio waveforms corresponding to this family of PWMs for an easy implementation. Modulations defined upon these vectors enable the use of diode-clamped topologies with passive front-ends. The performance of these converters operated with the proposed PWMs is compared to the performance of alternative designs through analysis, simulation, and experiments. [ABSTRACT FROM AUTHOR]

In the previous literature, it has been reported that it is not possible to guarantee the balance of the dc-link capacitor voltages of multilevel three-phase diode-clamped dc-ac converters with passive front-ends for high modulation indices, especially for more than three levels. This paper proposes a novel closed-loop control approach capable of guaranteeing such balance for all ope]rating conditions of the converters without the need for additional hardware. Three different phase duty-ratio perturbation schemes are proposed. They are compared through simulation for the case of a four-level three-phase diode-clamped dc-ac converter operated with a virtual-vector-based modulation. The most simple and effective perturbation scheme, only requiring the sensing of all dc-link capacitor voltages, is tested experimentally in the same four-level converter. The results demonstrate the feasibility of guaranteeing the dc-link capacitor voltage balance for all converter operating conditions. [ABSTRACT FROM AUTHOR]

This paper presents a novel approach for the connection of renewable energy sources to the utility grid. Due to the increasing power capability of the available generation systems, a three-level three-phase neutral-point-clamped voltage-source inverter is selected as the heart of the interfacing system. A multivariable control law is used for the regulator because of the intrinsic multivariable structure of the system. A current source (playing the role of a generic renewable energy source) is connected to the grid using a three-level inverter in order to verify the good performance of the proposed approach. Large- and small-signal d-q state-space averaged models of the system are obtained and used to calculate the multivariable controller based on the linear quadratic regulator technique. This controller simultaneously regulates the dc-link voltage (to operate at the maximum power point of the renewable energy source), the mains power factor (the power is delivered to the grid at unity power factor), and the dc-link neutral-point voltage balance. With the model and regulator presented, a specific switching strategy to control the dc-link neutral-point voltage is not required. The proposed controller can be used for any application, since its nature makes possible the control of any system variable. The good performance of the presented interfacing solution in both steady-state and transient operation is verified through simulation and experimentation using a 1-kW neutral-point-clamped voltage-source-inverter prototype, where a PC-embedded digital signal processor board is used for the controller implementation. [ABSTRACT FROM AUTHOR]

This article presents detailed Markov models for the reliability assessment of multilevel neutral-point-clamped (NPC) converter leg topologies, incorporating their inherent fault-tolerance under open-circuit switch faults. The Markov models are generated and discussed in detail for the three-level and four-level active NPC (ANPC) cases, while the presented methodology can be applied to easily generate the models for a higher number of levels and other topology variants. In addition, this article also proposes an extremely fast calculation method to obtain the precise value of the system's mean time to failure from any given formulated system Markov model. This method is then applied to quantitatively compare the reliability of two-level, three-level, and four-level ANPC legs under switch open-circuit-guaranteed faults and varying degrees of device paralleling. The comparison reveals that multilevel ANPC leg topologies inherently present a potential for higher reliability than the conventional two-level leg, questioning the suitability of the traditional search for topologies with the minimum number of devices in order to improve reliability. Experimental results are presented to validate the fault-tolerance assumptions upon which the presented reliability models for the three-level and four-level ANPC legs are based. This article is accompanied by supplementary MATLAB scripts. [ABSTRACT FROM AUTHOR]

This paper studies a multilevel multiphase dc–ac conversion system configured by a neutral-point-clamped converter fed by multiple battery packs connected in series. A virtual-vector modulation is selected and a state-of-charge (SoC) balancing control is designed to be able to employ the full battery bank capacity, even under different battery initial SoC values or different battery nominal capacities. The SoC balancing among battery packs is accomplished through the multilevel converter operation in a lossless manner, by simply distributing the dc-to-ac power flow among the batteries according to their SoC. A simple average system model is also presented, which allows performing very fast system simulations over long periods of time and serves as a convenient tool to tune the compensator parameters. The satisfactory performance of the proposed system configuration and control, which can be applied with any number of levels and phases, has been verified through simulations and experiments in a four-level three-phase dc–ac converter fed by three lithium-ion battery packs. The results prove the feasibility and advantages of the proposed system configuration, which can be used to implement conversion systems with different specifications combining several instances of a standard battery pack and a standard power semiconductor device. [ABSTRACT FROM AUTHOR]

This paper presents a model of a bidirectional MV/LV solid-state transformer (SST) for distribution system studies. A modular multilevel converter configuration is used in the MV side of the STT. The LV side uses a three-phase four-wire configuration that can be connected to both load and generation. The model developed for this work has been implemented in MATLAB/Simulink, and its behavior has been tested by carrying out several case studies under different operating conditions. The simulation results support the feasibility of the SST and its advantages in comparison to the conventional transformer. The paper also includes a discussion of the main model limitations and the future work. [ABSTRACT FROM AUTHOR]

In this paper, a predictive control scheme is proposed for the low-voltage ride-through (LVRT) enhancement of direct-driven permanent-magnet-synchronous-generator-based megawatt-level wind turbines. The proposed method uses the turbine–generator rotor inertia to store the surplus energy during the grid voltage dips. The power conversion system is realized using a three-phase diode-bridge rectifier, a three-level-boost converter, and a neutral-point-clamped (NPC) inverter. The wind turbine requirements, such as maximum power point tracking, net dc-bus voltage control, balancing of the dc capacitor voltages, and reactive power generation, are modeled as the reference control variables. The generator- and grid-side cost functions are defined to deal with these control objectives. During each sampling interval, the control goals are achieved based on the minimization of cost functions. The coordination of boost and NPC converters and the exchange of reference control variables during normal and LVRT operation are formulated such that the power converters operate in a safe mode while meeting the grid code requirements. Simulation and experimental results are presented to validate the proposed strategy. [ABSTRACT FROM PUBLISHER]

Doubly fed induction generators (DFIGs), often organized in wind parks, are the most important generators used for variable-speed wind energy generation. This paper reviews the control systems for the operation of DFIGs and brushless DFIGs in wind energy applications. Control systems for stand-alone operation, connection to balanced or unbalanced grids, sensorless control, and frequency support from DFIGs and low-voltage ride-through issues are discussed. [ABSTRACT FROM PUBLISHER]

This paper presents a generalized multilevel direct power control (ML-DPC) scheme for grid-connected multilevel power converters. The proposed method extends the original DPC operating principle by considering only the closest subset of two-level voltage vectors to the present switching state. The implementation of this principle requires the power derivatives for feedback, which can present numerical problems when applied experimentally, mainly due to high measurement noise sensitivity. Therefore, a derivative estimator is proposed based on the converter-grid model in the synchronous reference frame. In addition, a virtual flux observer is developed to achieve synchronization and improve robustness in the presence of grid voltage harmonics. The proposed method is applicable to any multilevel converter topology of any number of levels. In this paper, simulations and experimental results are presented for a seven-level cascaded H-bridge converter. [ABSTRACT FROM AUTHOR]

Thanks to the inherent redundancy to generate the different output voltage levels, the multilevel active-clamped (MAC) topology presents an important fault-tolerance ability which makes it interesting for several applications. This paper presents an analysis of the fault-tolerance capacity of the MAC converter. Both open-circuit and short-circuit faults are considered, and the analysis is carried out under single-device and two simultaneous device faults. Switching strategies and different hardware modifications to overcome the limitations caused by faults are proposed. Experimental tests with a four-level MAC prototype are presented to validate the analysis. [ABSTRACT FROM PUBLISHER]

In photovoltaic (PV) power systems where a set of series-connected PV arrays (PVAs) is connected to a conventional two-level inverter, the occurrence of partial shades and/or the mismatching of PVAs leads to a reduction of the power generated from its potential maximum. To overcome these problems, the connection of the PVAs to a multilevel diode-clamped converter is considered in this paper. A control and pulsewidth-modulation scheme is proposed, capable of independently controlling the op- erating voltage of each PVA. Compared to a conventional two-level inverter system, the proposed system configuration allows one to extract maximum power, to reduce the devices voltage rating (with the subsequent benefits in device-performance characteristics), to reduce the output-voltage distortion, and to increase the system efficiency. Simulation and experimental tests have been conducted with three PVAs connected to a four-level three-phase diode-clamped converter to verify the good performance of the proposed system configuration and control strategy. [ABSTRACT FROM AUTHOR]