Search

The effect of microwave pre-treatment on the magnetic properties of tennantite and enargite was investigated. Magnetic susceptibility, XRD, and XPS characterization of tennantite and enargite before and after treatment were conducted to explore the changes in their magnetic properties. Moreover, magnetic separation of chalcopyrite binary mixtures with enargite and tennantite was performed. The results showed insignificant effects on the magnetic susceptibility of the two minerals after microwave pre-treatment. Magnetic separation results showed arsenic rejection by 84.2%, and 76.3% in the case of enargite and tennantite binary mixtures with chalcopyrite; respectively.

Sodium metabisulfite (MBS) was used in this study for selective flotation of chalcopyrite and molybdenite. Microflotation tests of single and mixed minerals were performed to assess the floatability of chalcopyrite and molybdenite. The results of microflotation of single minerals showed that MBS treatment significantly depressed the floatability of chalcopyrite and slightly reduced the floatability of molybdenite. The results of microflotation of mixed minerals demonstrated that the MBS treatment could be used as a selective chalcopyrite depressant in the selective flotation of chalcopyrite and molybdenite. Furthermore, the addition of diesel oil or kerosene could significantly improve the separation efficiency of selective flotation of chalcopyrite and molybdenite using MBS treatment. A mechanism based on X-ray photoelectron spectroscopy analysis results is proposed in this study to explain the selective depressing effect of MBS on the flotation of chalcopyrite and molybdenite.

A 74-year-old man experienced complete atrioventricular (AV) block 2 days after catheter ablation for right atrial macroreentrant tachycardia. We performed DDD pacemaker implantation with atrial septal pacing because other sites of pacing threshold were not acceptable. The maximum left ventricular outflow tract velocity time integral was 15.8 cm with sensed AV delay (40 ms) and 15.0 cm with paced AV delay (220 ms); however, this exceeded the pacemaker's maximum difference of 100 ms. We herein report the case of a large discrepancy in optimal AV delay intervals between sensed and paced atrial events, requiring consideration of proper pacemaker settings. This article is protected by copyright. All rights reserved.

The copper ore in Chilean copper porphyry deposits is often associated with molybdenum minerals. This copper–molybdenum (Cu–Mo) sulfide ore is generally mined from various locations in the mining site, thus, the mineral composition, oxidation degree, mineral particle size, and grade vary. Therefore, in the mining operation, it is common to blend the ores mined from various spots and then process them using flotation. In this study, the floatability of five types of Cu–Mo ores and the blending of these ores in seawater was investigated. The oxidation degree of these Cu–Mo ores was evaluated, and the correlation between flotation recovery and oxidation degree is presented. Furthermore, the flotation kinetics of each Cu–Mo ore were calculated based on a mineralogical analysis using mineral liberation analysis (MLA). A mineralogical prediction model was proposed to estimate the flotation behavior of blended Cu–Mo ore as a function of the flotation behavior of each Cu–Mo ore. The flotation results show that the recovery of copper and molybdenum decreased with the increasing copper oxidization degree. In addition, the recovery of blended ore can be predicted via the flotation rate equation, using the maximum recovery (Rmax) and flotation rate coefficient (k) determined from the flotation rate analysis of each ore before blending. It was found that Rmax and k of the respective minerals slightly decreased with increasing the degree of copper oxidation. Moreover, Rmax varied greatly depending on the mineral species. The total copper and molybdenum recovery were strongly affected by the degree of copper oxidation as the mineral fraction in the ore varied greatly depending upon the degree of oxidation.

A fundamental study is provided in this work to understand the effect of Fenton-like reagent made by the addition of FeSO4 in H2O2 aqueous solution on surface hydrophobicity and floatability of chalcopyrite (CuFeS2) and molybdenite (MoS2). Contact angle measurements were performed to assess the surface hydrophobicity. The contact angle results showed that Fenton-like reagent could alter the surface hydrophobicity of chalcopyrite at lower concentration of H2O2 aqueous solution compared to that of using H2O2 aqueous solution. On the other hand, molybdenite surface remained hydrophobic after the oxidation treatments using Fenton-like reagent and H2O2 aqueous solution. Surface characterizations using atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS) shows that the chalcopyrite surface covered with a thicker layer of oxidation products after the oxidation treatment using Fenton-like reagent, indicating a stronger surface oxidation. Flotation results were in agreement with contact angle results, showing that Fenton-like reagent could depress the floatability of chalcopyrite at lower concentration of H2O2 aqueous solution. On the other hand, molybdenite recovery remained high under various oxidation treatments owing to low surface oxidation.

Hydrogen peroxide (H2O2) has been used as an oxidizing agent in the selective flotation of chalcopyrite and molybdenite. However, this method required relatively high concentration of H2O2 to deliver flotation results (i.e., mineral grades and recoveries) comparable to those obtained by the conventional copper-molybdenum (Cu-Mo) ores flotation using sodium hydrosulfide (NaHS). Therefore, further improvements are needed to reduce the consumption of H2O2 reagent. In this study, ferrous sulfate (FeSO4) was used to enhance the oxidation performance of H2O2 through Fenton-like reactions. Flotation results showed that the consumption of H2O2 reagent could be reduced by the addition of FeSO4 without losing the flotation selectivity. The reason might be caused by increasing of oxidation performance as indicated by the increasing concentration of dissolved oxygen after the addition of FeSO4 into the H2O2 aqueous solution. Surface analysis using X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM) images showed that the surface of chalcopyrite was covered by more hydrophilic precipitates after the oxidation treatment using H2O2 aqueous solution with the addition of FeSO4, thus more hydrophilic surface and lower floatability. On the other hand, the surface of molybdenite was slightly oxidized and its surface remained hydrophobic as confirmed from contact angle results. Flotation tests using Cu-Mo bulk concentrate demonstrated that selective flotation might be possible using a mixture of FeSO4 and H2O2 aqueous solution. Moreover, this new method could be used as an alternative to copper depressant in Cu-Mo selective flotation, replacing the NaHS reagent.

Effect of silver (Ag) catalyst in bioleaching of enargite (Cu_3AsS_4) concentrate was studied using mixed cultures of moderately thermophilic acidophilic microorganisms at 45ºC. Addition of Ag_2S enabled selective Cu dissolution from enargite while suppressing pyrite oxidation: At the highest Ag_2S concentration of 0.04%, Cu recovery reached 96% while Fe dissolution was suppressed to reach only 29% by day 72. Overall results from thermodynamic calculation, liquid/solid analyses and kinetic study suggested that Ag-catalyzed bioleaching of enargite concentrate proceeds via formation of at least two types of secondary products (chalcocite, Cu_2S; trisilver arsenic sulfide, Ag_3AsS_4): Addition of Ag_2S as Ag catalyst thermodynamically and microbiologically contributed to lowering solution redox potentials during bioleaching, consequently satisfying Eox (Cu_2S) < E_h < E_c (Ag+) to enhance enargite dissolution via formation of chalcocite intermediate. Formation of trisilver arsenic sulfide and its intermediate layer (Cu,Ag)_3AsS_4 indicated that Cu ion in the enargite lattice is gradually substituted with Ag. Such secondary products did not impose a rate-limiting step, since the Ag-catalyzed bioleaching was shown to be controlled by a chemical surface reaction, rather than diffusion through product film which was the case in the absence of Ag_2S.

The effect of controlling the redox potential (Eh) on chalcopyrite bioleaching kinetics was studied as a new aspect of redox control during chalcopyrite bioleaching, and its mechanism was investigated by employing the “normalized” solution redox potential (Enormal) and the reaction kinetics model. Different Eh ranges were established by use of different acidophiles (Sulfobacillus acidophilus YTF1; Sulfobacillus sibiricus N1; Acidimicrobium ferrooxidans ICP; Acidiplasma sp. Fv-AP). Cu dissolution was very susceptible to real-time change in Eh during the reaction. It was found that efficiency of bioleaching of chalcopyrite can be effectively evaluated on the basis of Enormal, since it is normalized for real-time fluctuations of concentrations of major metal solutes during bioleaching. For steady Cu solubilization during bioleaching at a maximum rate, it was important to maintain a redox potential range of 0 ≤ Enormal ≤ 1 (-0.35 mV optimal) at the mineral surface by employing a “weak” ion-oxidizer. This led to a copper recovery of > 75%. At higher Enormal levels (Enormal > 1 by “strong” microbial Fe_2+ oxidation), Cu solubilization was slowed by diffusion through the product film at the mineral surface (< 50% Cu recovery) caused by low reactivity of the chalcopyrite and by secondary passivation of the chalcopyrite surface, mainly by jarosite.

Seawater has been reported to depress the floatability of molybdenum in copper-molybdenum (Cu-Mo) flotation circuits under alkaline conditions (pH > 9.5). However, the seawater used in the process contains various minerals and flotation reagents, which make it difficult to investigate the depression mechanism. This paper presents a fundamental study into the effect of artificial seawater as a seawater model solution on the floatability of molybdenite and chalcopyrite, which are the main minerals in the Cu-Mo flotation process. Floatability tests in the absence of flotation reagents (i.e., frothers and collectors) reveal that artificial seawater adversely affects the floatability of molybdenite and chalcopyrite at pH > 9. This phenomenon can be attributed to the adsorption of hydrophilic Mg(OH)2 precipitates formed under alkaline conditions on the mineral surfaces, which increases the surface wettability of the mineral particles, as shown by contact angle measurements and atomic force microscopy (AFM) images. The effect of kerosene as a molybdenite collector has also been investigated to assess its potential in the selective flotation of molybdenite and chalcopyrite in artificial seawater.

The effect of sodium sulfite (Na2SO3) on the floatability of chalcopyrite and enargite was investigated in this work. The micro flotation tests of single and mixed minerals were performed under various concentrations of Na2SO3. The micro flotation tests of single minerals showed that Na2SO3 depressed the floatability of both minerals at pH 9 in the absence of potassium amyl xanthate (PAX). Interestingly, the addition of PAX followed by the Na2SO3 treatment selectively improved the recovery of enargite. On the other hand, the recovery of chalcopyrite remained low under a similar condition. The single mineral flotation results indicate that separation of chalcopyrite and enargite might be possible using PAX and Na2SO3 treatment. Indeed, the mixed mineral flotation results were in agreement with the flotation results of single minerals. The mineral surface was analyzed by X-ray photoelectron spectroscopy (XPS) after the treatments to explain the phenomenon. The XPS results show the presence of sulfate species on both mineral surfaces after the Na2SO3 treatment. The adsorbed PAX could prevent the formation of this sulfate species on the enargite surface and rendered the surface hydrophobic. However, the adsorbed PAX could not prevent the formation of sulfate species on the chalcopyrite surface and rendered the surface hydrophilic.

This paper summarizes the results of a voltammetric study of the anodic characteristics of chalcopyrite in the potential region relevant to heap leaching in concentrated chloride solutions. Distinct peaks in the potential region of 0.7 to 0.85 V have been observed in the voltammograms, the magnitude of which depend on the chloride concentration and, particularly, the pH in the range 1 to 3. Three peaks are observed at low chloride concentrations that merge into one peak at higher concentrations. The anodic reactivity increases with increasing pH but shows a complex dependence on the chloride concentration while in the presence of added copper(II) ions, the mixed potential shifts to more positive potentials and only one peak is observed. Hysteresis between the forward and backward-going sweeps has confirmed the transient nature of the processes except at potentials below about 0.75 V in which region the system approaches steady-state behaviour. The voltammetric characteristics of chalcopyrite in this system appear to be very similar to those of covellite. Measurements of the initial rates of dissolution (in the range 1–5 × 10− 10 mol cm− 2 s− 1 depending on the conditions) have been made that confirm the voltammetric trends and compare well with previously published rates. Linear free energy relationships have been used to estimate the thermodynamic properties (Gibbs free energy − 100.7 kJ/mol) of the simplest polysulfide, namely CuS2 and possible mechanisms for the various steps in the anodic dissolution and passivation of chalcopyrite have been suggested that are consistent with the thermodynamic predictions.

The selective flotation of chalcopyrite (CuFeS2) and molybdenite (MoS2) was studied using surface oxidation treatments (i.e., ozone (O3) and hydrogen peroxide (H2O2)). The results indicated that the oxidation treatments had different effects on the wettability of chalcopyrite and molybdenite. Single mineral flotation results showed that the H2O2 treatment had higher separation selectivity for molybdenite and chalcopyrite compared with that of the ozone treatment. The contact angle measurement and X-ray photoelectron spectroscopy (XPS) analysis results showed that the chalcopyrite surface became hydrophilic owing to the surface deposition of oxidized iron and copper after the H2O2 treatment. On the other hand, the contact angle of molybdenite slightly increased following the H2O2 treatment at high concentrations. Possible mechanisms of this phenomenon were proposed in this work. Moreover, the separation selectivity of each oxidation method was discussed. Flotation tests using bulk Cu-Mo concentrate showed that H2O2 could deliver a flotation result comparable to conventional Cu-Mo flotation using NaHS.

Seawater flotation has been applied to mineral processing in areas located far from fresh water resources. However, as seawater has a detrimental effect on molybdenite floatability under alkaline conditions (pH > 9.5), its application in the conventional copper and molybdenum (Cu-Mo) flotation circuit is hindered. A fundamental study of the effect of two divalent cations in seawater, Mg 2+ and Ca 2+ , on the floatability of chalcopyrite and molybdenite is presented in this paper. Floatability tests showed that both MgCl 2 and CaCl 2 solutions depress the floatability of chalcopyrite and molybdenite at pH values higher than 9. Furthermore, Mg 2+ exerts a stronger effect than Ca 2+ owing to the adsorption of Mg(OH) 2 precipitates on the mineral surfaces, as indicated by dynamic force microscopy images. The floatability of chalcopyrite was significantly depressed compared with that of molybdenite in a 10 −2 M MgCl 2 aqueous solution at pH 11. This phenomenon is likely due to the adsorption of hydrophilic complexes on the mineral surface, which reduces the surface hydrophobicity. A reversal of the zeta potential of chalcopyrite in MgCl 2 and CaCl 2 solutions at pH 11 and 8, respectively, indicated the adsorption of precipitates onto the surface. In contrast, the zeta potential of molybdenite decreased continuously under the same conditions. The floatability test of chalcopyrite and molybdenite in mixed systems showed that selective separation of both minerals should be possible with the addition of emulsified kerosene to a 10 −2 M MgCl 2 solution at pH 11. A mechanism is proposed to explain this phenomenon.

The formation of stable bubble–particle aggregates is essential to the froth flotation process. To form such aggregates, bubbles and particles must collide, the intervening liquid film must be drained below its critical rupture thickness, and three-phase contact (TPC) formation must occur. A good understanding of the interaction mechanism between bubbles and particles during collision and attachment is important. We herein investigated the effects of emulsified kerosene in a 0.01 M MgCl2 solution (a model seawater component) on bubble interactions with pure molybdenite (MoS2) and chalcopyrite (CuFeS2) surfaces. In 0.01 M MgCl2 at pH 6 and 11, kerosene retarded the bubble surface mobility and reduced the bubble rise velocity. In the presence of kerosene at pH 6, the TPC formed more rapidly on both mineral surfaces. This was due to the increase in surface hydrophobicity caused by kerosene. In addition, TPC formation was more rapid on the molybdenite surface than on the chalcopyrite surface due to the effect of the adsorbed kerosene and the low surface homogeneity of molybdenite. Finally, floatability tests demonstrated that the separation of molybdenite and chalcopyrite should be possible by adding emulsified kerosene in a 0.01 M MgCl2 solution at pH 9.

Catalytic effects of silver on the dissolution of arsenic-containing copper sulfides such as enargite in acidic media were investigated. Leaching experiments showed that silver increased the enargite dissolution rate, and that the dissolution behavior was potential-dependent. The addition of silver ions and silver sulfide greatly enhanced enargite dissolution. Such behavior can be explained based on the following reaction model: enargite dissolution is enhanced by silver as the silver ions remove the hydrogen sulfide produced during enargite reduction, giving the more amenable copper sulfide. Thermodynamic calculations suggested that the addition of silver ions and controlling the potential would maintain a high enargite dissolution rate. Leaching experiments were therefore performed with the addition of silver sulfide and potential control using an automatic titration apparatus. Experimental results showed that a combination of these two factors gave high enargite dissolution; i.e., 75% copper was dissolved in 24 h at 0.750–0.850 V vs. the standard hydrogen electrode at 303 K.

The detrimental effect of seawater on Cu-Mo flotation has attracted much attention in recent years, which has mainly been focused on altering the detrimental effect of seawater on the floatability of molybdenum ore. The interaction between bubbles and particles during flotation is a key factor in understanding the detrimental effect of seawater. Therefore, this study aimed to investigate the effect of seawater on bubble-particle interactions with chalcopyrite and molybdenite surfaces. Moreover, the effect of emulsified kerosene, a typical molybdenite collector, on bubble-particle interactions in seawater was investigated. Artificial seawater was used as a seawater model solution in this study. Flotation tests using pure chalcopyrite and molybdenite showed that the addition of emulsified kerosene to artificial seawater at a specific pH could selectively improve the floatability of molybdenite while maintaining the low floatability of chalcopyrite. A study of the bubble-particle interactions was then performed to analyze the phenomenon. It was found that the kerosene adsorbed at the air/liquid interface of the bubble improved the bubble aspect ratio and reduced the bubble rise velocity in artificial seawater. Moreover, kerosene could accelerate the formation of three-phase contact between the bubble and both mineral surfaces at the natural pH of artificial seawater. Additionally, this study showed that seawater colloidal precipitate formed under high pH conditions might be adsorbed on the mineral surfaces and might improve the stability of the intervening liquid film on the surface, thus preventing bubble-particle attachment and decreasing mineral recovery. Under these high pH conditions, the emulsified kerosene and seawater precipitate might compete in terms of adsorption on the mineral surfaces and the flotation results would most likely depend on the kerosene and hydrophilic adsorbate coverage on the mineral surfaces.

Natural carbonaceous matter aided the bioleaching of Cu from chalcopyrite concentrates. The oxidative dissolution of chalcopyrite was enhanced more significantly by anthracite than carbonaceous matter in double refractory gold ore (DRGO). This was achieved through Galvanic interactions between the chalcopyrite and natural carbonaceous matter. Measurement of impedance verified that the electro-resistance is smaller in anthracite, which has a greater graphitic degree than carbonaceous matter in DRGO. The electron shuttle between chalcopyrite and the Fe3+ /Fe2+ redox couple was facilitated not only by the amounts of carbonaceous matter but also the degree of graphitization of carbonaceous matter. A higher graphitization degree increased the electron conductivity of the carbonaceous matter to help mediate Cu bioleaching while avoiding direct contact of thermophile cells with refractory copper sulfides.

Effect of oxidation treatment using hydrogen peroxide (H2O2) on the floatability of copper sulfide minerals (i.e., chalcopyrite and bornite) and arsenic-bearing copper minerals (i.e., tennantite and enargite) is reported in this study. Pure mineral flotation shows that the floatability of each mineral significantly decreases after the oxidation treatment. Interestingly, flotation of mixed mineral of copper sulfide and arsenic-bearing copper minerals shows that enargite and tennantite exhibit a higher floatability compared to chalcopyrite and bornite after the oxidation treatment followed by the addition of potassium amyl xanthate (PAX). These flotation results indicate a possibility for selective flotation of copper sulfide and arsenic-bearing copper minerals. Indeed, bench-scale flotation tests show that the oxidation treatment using H2O2 and the addition of PAX can deliver a satisfying separation of copper sulfide and arsenic-bearing copper minerals. Difference oxidation products (i.e., CuO, Cu(OH)2, CuSO4, FeOOH, and Fe2(SO4)3) on each mineral surface are likely the cause of this different flotation behavior. Furthermore, these oxidation products may affect the adsorption amount of PAX on each mineral. Indeed, the adsorption tests show that PAX is adsorbed more on tennantite, bornite, and enargite compared to chalcopyrite owing to the formation of CuSO4 and Cu(OH)2 on the mineral surfaces under oxidizing conditions. A possible mechanism is proposed in this study to explain the selective flotation behavior of mixed minerals.

Co-precipitation of borate in a wide range of concentration with hydroxyapatite (HAp) was investigated using Ca(OH) 2 as a mineralizer in the presence of phosphate. The sorption data of borate was fitted to Freundlich model. The maximum sorption density of B/Ca to maintain a mono-phase of HAp was found around 0.40. In higher B concentrations, borate was still immobilized, however, the crystalization of hydroxyapatite was inhibited, where the solid residues were accompanied with amorphous CaB 2 O 4 , as well as HAp. Based on 11 B-NMR and elemental analysis for solid residues in addition to solution chemistry, the removal mechanism of high concentration borate can be explained by the surface complexation of triborate on Ca(OH) 2 , subsequently decomposition of triborate into monoborate to release [CaB(OH) 4 ] + and B(OH) 4 − , followed by co-precipitation with HAp. These tetragonal B species were immobilized in the solid residues including amorphous HAp. During the process there was a trend to eliminate carbonate from the solid phase. TEM images suggested that the HAp particles precipitated at room temperatures were in a fibrous shape consisting of a number of short rods when borate species are not added. When borate species were immobilized, the HAp particles have gotten swelled with losing fibrous shapes. When further higher borate concentrations were encapsulated in co-precipitated products, the morphologies were dramatically changed, that is, nano-sized and less crystalline HAp particles were enveloped by possibly amorphous CaB 2 O 4 .

Joint Program for Sustainable Resources Engineering was adopted as a Special Expenditure Project by the Ministry of Education, Culture, Sports, Science and Technology in Japan. In this project, in order to cultivate human resources who can contribute to Japan’s resource strategies, Education and Research Departments of Resources Engineering at Kyushu University and Hokkaido University aim to jointly establish a new collaborative education program in 2017. This is the first of its kind in the resources engineering area among universities in Japan. One of the pillar of this program is “International Field Practice”. For working actively and globally in the field of sustainable resources engineering, one need to (1) acquire internationally accepted knowledge and techniques in the fields, (2) be capable of utilizing the knowledge and techniques practically, and (3) understand cultures in foreign countries as well as global trends in the field. In this exercise, students work on an internship or conduct a field research in a foreign country in the field of sustainable resources engineering. Through this exercise, students learn how to develop their leadership and adaptability in the world, and to communicate scientifically and technically in English presentation, discussion, and writing. This paper describes the overview of this program and the International Filed Exercise 2017 conducted in Czech Republic.

For pretreatment of selective flotation, plasma treatment of chalcopyrite and molybdenite was applied then the minerals were washed by solution at pH 9 with oxygen bubbling. Surface characteristics of these minerals were investigated with AFM, XPS, zeta potential and contact angle measurements. Contact angle of chalcopyrite and molybdenite decreased a lot by plasma treatment. When they were washed with pH 9 solution with oxygen bubbling, contact angle of molybdenite increased whereas chalcopyrite one kept low. Adhesion force measurements indicated similar behavior. Result of flotation experiments indicated low recovery of both chalcopyrite and molybdenite after plasma treatment and only molybdenite recovery became higher after washing. Selective flotation of chalcopyrite and molybdenite could be achieved with this process. However, flotation of mixture of chalcopyrite and molybdenite after these treatments indicated both chalcopyrite and molybdenite were depressed. Addition of emulsified kerosene changed the flotation results where molybdenite was floated and chalcopyrite was depressed. Possible mechanism of selective flotation was proposed from the results of XPS, AFM, etc.

Part I of this series described the results of a study of the electrochemistry of pyrite under conditions similar to those encountered in acidic bioleaching of the mineral. In this paper, the electrochemical data obtained in the previous paper is used to derive estimates of the rate of leaching of pyrite based on a mixed potential model for the kinetics as a function of the solution composition and temperature. The results of the calculated rates of dissolution are compared with those obtained in a limited study of the dissolution of a milled pyrite sample at controlled potentials. It is demonstrated that the rate of dissolution calculated from the anodic current density in a solution without iron(III) when the potential is held at the mixed potential measured in the presence of iron(III) compared well with the rate predicted by the linear polarization method and that obtained from the change in the solution potential with time in a batch dissolution of a pyrite electrode in solutions containing iron(III). The dissolution rate calculated from the steady-state currents at the mixed potential in the absence of iron(III) decreased with increasing sulphate ion concentration, increased with increasing temperature and also with increasing rotation speed of the pyrite electrode. The results of leaching experiments with milled pyrite under conditions of controlled solution potential has shown that the rate of dissolution is significantly higher at a potential of 0.85 V than at 0.80 V. Approximately 90% of the sulphide associated with pyrite is oxidised to elemental sulphur. The results of the leach experiments quantitatively agree well with those derived from the electrochemical measurements. The detrimental effect of high sulphate concentrations on the rate of dissolution has been confirmed by the leach tests.

A detailed study of the electrochemical behavior of pyrite under typical bio-leaching conditions has been carried out with the focus on the effect of the concentration of sulphate ions on the mixed potential, cyclic voltammetric and potentiostatic measurements. The mixed potential decreases with increasing sulphate ion concentration and the addition of iron(II) and increases as expected with increasing iron(III) concentration and agitation at constant pH. Temperature, pH and the concentration of dissolved oxygen have minimal effects on the mixed potential in the presence of iron(III). Cyclic voltammetric and potentiostatic data confirm that the rate of anodic oxidation of pyrite decreases with increasing sulphate ion concentration and increases with increasing temperature. The pH and dissolved oxygen concentration have little effect while addition of chloride ions inhibits the anodic oxidation of pyrite. Studies of the cathodic reduction of iron(III) and dissolved oxygen have shown that the rate of the former is several orders of magnitude more reversible(rapid) than that of dissolved oxygen which only exhibits measurable reactivity at potentials well below the mixed potentials in the presence of iron(III). The reduction of iron(III) is inhibited by sulphate ions due to the formation of electrochemically less reactive sulphate complexes.

An electrode system to study the mechanism of fine microgram powder sulfide mineral dissolution was developed by using a relatively simple method that enables the attachment of micrograms of fine powder to a platinum plate surface. This system yields highly reproducible results and is sensitive compared with conventional electrode systems for various sulfide minerals such as pyrite, chalcopyrite, chalcocite, enargite, and tennantite. The leaching behavior of chalcopyrite was re-examined in a test of the application of this electrode system. Chalcopyrite dissolution is enhanced in specific potential regions because it is believed to be reduced to leachable chalcocite, but this result is inconclusive because it is difficult to detect the intermediate chalcocite. Powder chalcopyrite in the new powder electrode system was held at 0.45 V in the presence of copper ion and sulfuric acid media followed by an application of potential in the anodic direction. Besides the chalcopyrite oxidation peak, a small peak resulted at ∼0.55 V; this peak corresponds to reduced chalcocite, because it occurs at the same potential as the chalcocite oxidation peak.

The use of chloride in the heap leaching of sulfide minerals requires the regeneration of the oxidants copper(II) and iron(III). While this is possible in a sulfate system by the use of bacterially catalysed oxidation of iron(II), this can only economically be achieved by chemical reaction with dissolved oxygen in chloride systems due to the sensitivity of bacteria to high concentrations of chloride ions. The kinetics of the reduction of dissolved oxygen by copper(I) in acidic chloride solutions has been studied under possible heap leach conditions. The results confirm some published data that the rate is second-order in copper(I). The rate increases with increasing acid concentrations but decreases with increasing chloride and copper(II) concentrations. Peroxide has been shown to be a detectable intermediate and a modified mechanism has been proposed which is consistent with the kinetic data. The use of the derived rate equation in a modified rate expression for the copper-catalysed auto-oxidation of iron(II) has been derived.

A parametric study on configurations of a boundary-layer diverter for supersonic propulsion system was conducted using CFD simulation to examine those effects on the flow field and the performances of the diverter. The performances were evaluated in terms of its aerodynamic drag and ingestion of the boundary-layer on the airframe surface. Height, width, and apex angle of the diverter were used as the parameters. It is found that narrow width yields good performances in terms of the drag as well as the boundary-layer ingestion. The effect of height and apex angle exhibits trade-off between aerodynamic drag and ingesting the boundary-layer. In the design process of diverter, firstly, the width of diverter should be set to minimum value, then, the apex angle and the height should be optimized.

In Parts 1 and 2 of this series, which describe the results of a study of the dissolution of chalcopyrite under conditions that could be expected in a heap leaching process for primary copper minerals, it was shown that enhanced leaching of chalcopyrite from several copper concentrates in dilute acidic chloride solutions can be achieved by controlling the potential in a "window" of 560-600 mV (SHE) in the presence of dissolved oxygen. It was also found that the rate is linear and essentially independent of the initial concentration of chloride and cupric ions under these conditions. Furthermore, the rate appears to be largely independent of the source of the mineral and is strongly dependent on the temperature (activation energy = 72 kJ mol- 1). In this part, additional kinetic data on the effects of fine pyrite on the rate complemented by detailed mineralogical analysis of the residues will be used to demonstrate that sulfur forms a soluble intermediate such as H2S in the dissolution reaction. A summary of the results of a detailed study of the kinetics of the copper ion catalysed oxidation of H 2S by dissolved oxygen is presented which provides further support for a mechanism for the dissolution of chalcopyrite under heap leach conditions which involves an initial step involving non-oxidative dissolution to form H2S and either cupric ions or a covellite-like surface as the initial products.

The leaching rate of chalcopyrite (CuFeS2) in H2SO4 solutions depends on the redox potential determined by the concentration ratio of Fe3+ to Fe2+, and the rate is higher at redox potentials below a critical value (critical potential). In actual leaching systems, different metal ions are released from coexisting minerals to the aqueous phase. The present study investigated the effects of coexisting metal ions on the critical potential of chalcopyrite leaching. Shaking-flask leaching experiments were carried out with 0.1 g of ground chalcopyrite and 10 cm3 of 0.1 kmol m− 3 H2SO4 containing 0.1 kmol m− 3 Fe2+ and 0.001 kmol m− 3 of the metal ions at 298 K in air. The initial redox potential was adjusted by adding Fe3+, and the amount of Cu extracted after 24 h was investigated as a function of the potential. The results indicate that the critical potential increases by the addition of Ag+ or Bi3+ but is not affected by Pd2+, Hg2+, Cd2+, Zn2+, Ni2+, Co2+, or Mn2+. The results were interpreted by a reaction model assuming the formation of intermediate Cu2S due to the reduction of chalcopyrite and subsequent oxidation of the Cu2S at potentials below the critical potential. Catalytic effects of metal ions on chalcopyrite leaching are also discussed based on the experimental results and the proposed model.

Copper extraction during the oxidative leaching of chalcopyrite (CuFeS2) by ferric ions or by dissolved oxygen in sulfuric acid solutions is known to be faster at low redox potentials but slower at potentials above a critical value. The present study shows that this phenomenon occurs only when cupric and ferrous ions coexist, based on electrochemical measurements. Using a chalcopyrite electrode prepared from an ore lump sample, effects of the addition of 0.1 kmol m−3 cupric and ferrous ions on anodic polarization curves and AC impedance spectra were investigated in 0.1 kmol m−3 sulfuric acid with stirring at 298 K in nitrogen. Without cupric and/or ferrous ions, the anodic current increased monotonically with increasing applied potential. When cupric and ferrous ions coexisted, active-passive behavior was observed, i.e., the current increased with increasing potential to reach a maximum and it suddenly decreased at a certain potential, whereby the current became less dependent on the potential. In the active region, i.e., at low potentials, the anodic current with coexisting cupric and ferrous ions was larger than that without these ions. These results agree well with the results of leaching experiments reported previously, and indicate that coexisting cupric and ferrous ions promote the anodic dissolution of chalcopyrite at low potentials. The analysis of the AC impedance spectra indicates that a high-resistance passive layer grows on the chalcopyrite surface without cupric and/or ferrous ions, and that coexistence of these ions causes a formation of another product layer and inhibits the passive layer growth in the active region. To interpret the active-passive behavior of chalcopyrite, a reaction model, assuming the formation of intermediate Cu2S in the active region, is discussed based on the experimental results.

Chalcopyrite leaching in sulfuric acid solutions depends on the redox potential determined by the concentration ratio of ferric to ferrous ions, and the leaching rate is higher at redox potentials below a critical value. Previously, the authors have proposed a reaction model to interpret this phenomenon. The present study applied the model to interpret the catalytic effect of silver ions on chalcopyrite leaching. The model assumes that at lower potentials, chalcopyrite leaching proceeds in two steps: first, chalcopyrite is reduced by ferrous ions to form Cu 2 S that is more rapidly leached; next, the intermediate Cu 2 S is oxidized by ferric and/or dissolved oxygen to release cupric ions. During the chalcopyrite reduction, hydrogen sulfide is released to the liquid phase. Silver ions react with the hydrogen sulfide to form silver sulfide precipitate and decrease the concentration of hydrogen sulfide in the liquid phase, causing a rise in the critical potential of Cu 2 S formation and broadening of the potential range where rapid copper extraction takes place. To confirm the model, the redox potential dependence of chalcopyrite leaching was investigated in the presence of various concentrations of silver ions with 0.1 kmol m −3 sulfuric acid containing known concentrations of ferrous and ferric ions at 298 K in air. The critical potential increased with increasing concentrations of silver ions. This agrees with the model proposed here but cannot be explained by the conventional model proposed by Miller et al.

A supersonic air-inlet with bypass technique intended to reduce spillage drag was designed based on a characteristic of an actual jet engine. The effects of bypass design on drag reduction and pressure recovery was examined using CFD simulation. It was found that the bypass design gives a significant drag reduction as well as improves pressure recovery of inlet. The decrement of inlet drag largely surpasses the increment of the nacelle drag within the engine operating range. Furthermore, the bypass duct should be closed when an inlet operates in supercritical condition. Additionally, aerodynamic performance of inlet with diverterless configuration was evaluated to investigate the effects of boundary layer ingestion from airframe surface. In order to improve the inlet performance, a half-conical ramp was adopted to external compression inlet design. It became clear that, thick boundary-layer ingestion causes a huge flow separation within a conventional type inlet, and both pressure recovery and spatial distortion decay drastically. The half-conical ramp prevents boundary-layer from separating, and it is a promising option for diverterless inlet design.

The effects of ferrous ions on chalcopyrite oxidation with ferric ions in 0.1 mol dm−3 sulfuric acid solutions were investigated by leaching experiments at 303 K in nitrogen. With high cupric ion concentrations, the chalcopyrite oxidation was enhanced by high concentrations of ferrous ions and copper extraction was mainly controlled by the concentration ratio of ferrous to ferric ions or the redox potential of solutions. Ferrous ions, however, suppressed the chalcopyrite oxidation when cupric ion concentrations were low. A reaction model, which involves chalcopyrite reduction to intermediate Cu2S by ferrous ions and oxidation of the Cu2S by ferric ions, was proposed to interpret the results.

Oxidative leaching of chalcopyrite with dissolved oxygen and/or with ferric ions is promoted by high concentrations of ferrous ions in sulfuric acid solutions containing cupric ions. This paper proposes a reaction model to interpret this phenomenon and the thermodynamics of the leaching is discussed. The model considers the leaching to take place in two steps: (1) reduction of chalcopyrite to Cu2S by ferrous ions in the presence of cupric ions and (2) oxidation of the Cu2S to cupric ions and elemental sulfur by dissolved oxygen and/or by ferric ions. The intermediate Cu2S is more amenable to oxidation than chalcopyrite, causing enhanced copper extraction. The model predicts that the formation of intermediate Cu2S and ferrous-promoted chalcopyrite leaching occur when the redox potential of the solution is below a critical potential that is a function of the ferrous and cupric ion concentrations. To confirm this, flask-shaking leaching experiments were carried out with 0.1 mol dm−3 sulfuric acid solutions containing known concentrations of ferrous, ferric, and cupric ions at 303 K in air. The results agreed well with the predictions, i.e. copper extraction was enhanced at solution potentials below the critical potential predicted with the model.

The oxidation of iron(II) is an essential step in the oxidative leaching of uranium(IV) minerals such as uraninite and one of the reagents used in practice for this oxidation is sodium chlorate. This paper presents the results of an investigation into the kinetics of the oxidation of iron(II) by chlorate in solutions typical of the leaching of uranium. The results have confirmed the known form of the rate equation which is first-order in each of iron(II), chlorate and acid concentration. An overall rate equation has been derived which can be used to model the rate of iron(II) oxidation as a function of the reactant concentrations and the temperature. The half-life was found to be less than 1 min under typical leach conditions at the Olympic Dam operation in South Australia and this species cannot be considered to be the direct oxidant for uranium(IV) minerals.

Ferrous ions enhance copper extraction from chalcopyrite in sulfuric acid solutions in air at ambient temperatures, because they promote chalcopyrite oxidation with dissolved oxygen. However iron-oxidizing bacteria such as Thiobacillus ferrooxidans rapidly consume ferrous ions, suppressing copper extraction. In this paper, three compounds were used to inhibit ferrous oxidation by T. ferrooxidans and their effects on ferrous promoted chalcopyrite leaching were investigated in the presence and absence of the bacteria. Sodium lauryl sulfate and tannic acid suppressed not only the bacterial ferrous oxidation but also the chalcopyrite oxidation with dissolved oxygen, resulting in a suppression of copper extraction. High concentrations of sulfuric acid (> 0.05 mol dm-3) suppressed the bacterial ferrous oxidation and promoted chalcopyrite oxidation with dissolved oxygen, causing enhanced copper extraction.