Search

Hydraulic pumps are considered to have a major contribution to the structure borne noise generated inside aircrafts. Methods such as Component-Based Transfer Path Analysis (CB-TPA) are promising tools for aircraft manufacturers to build internal processes for the specification, design and validation of the impact of vibrating systems on new aircrafts. However, the experimental applicability of these methods remains limited due to some experimental difficulties. CB-TPA' formulation is based on dynamical quantities, which require the determination of terms related to rotational degrees of freedom. Virtual Point (VP) or Equivalent Multi-Point Connection (EMPC) methods are commonly employed for this purpose, but both result in more cumbersome experimental set-ups and increased measurement uncertainties. The implementation of these methods is difficult in the case of a flat and thin receiving structure as commonly encountered in aircraft applications, since in-plane translational excitations have to be applied and the access to the vibrating system/structure interface points is limited. In this work, a decoupling procedure is used to overcome these issues. A numerical model is used to investigate the influence of model and operator uncertainties on the CB-TPA' predictions, when the dynamical quantities are provided by VP and EMPC methods including the decoupling procedure.

Designing earplugs adapted for the widest number of earcanals requires acoustical test fixtures (ATFs) geometrically representative of the population. Most existing ATFs are equipped with unique sized straight cylindrical earcanals, considered representative of average human morphology, and are therefore unable to assess how earplugs can fit different earcanal morphologies. In this study, a methodology to cluster earcanals as a function of their morphologies with the objective of designing artificial ears dedicated to sound attenuation measurement is developed and applied to a sample of Canadian workers’ earcanals. The earcanal morphologic indicators that correlate with the attenuations of six models of commercial earplugs are first identified. Three clusters of earcanals are then produced using statistical analysis and an artificial intelligence-based algorithm. In the sample of earcanals considered in this study, the identified clusters differ by the earcanal length and by the surface and ovality of the first bend cross section. The cluster that comprises earcanals with small girth and round first bend cross section shows that earplugs induced attenuation significantly higher than the cluster that includes earcanals with a bigger and more oval first bend cross section.

The occlusion effect (OE) occurs when the earcanal becomes occluded by an in-ear device, sometimes leading to discomforts experienced by the users due to the augmented perception of physiological noises, or to a distorted perception of one's own voice. The OE can be assessed objectively by measuring the amplification of the low-frequency sound pressure level (SPL) in the earcanal using in-ear microphones. However, as revealed by methodological discrepancies found in past studies, the measurement of this objective occlusion effect (OEobj) is not standardized. With the goal of proposing a robust yet simple methodology adapted for field assessment, three experimental aspects are investigated: (i) stimulation source and the stimulus's characteristics to induce the phenomenon, (ii) measurement method of the SPL in earcanal, (iii) indicator to quantify the OEobj. To do so, OEobj is measured on human participants in laboratory conditions. Results obtained with a specific insert device suggest using the participant's own voice combined with simultaneous measurements of the SPLs based on the noise reduction method and using a single value indicator leads to a simple yet robust methodology to assess OEobj. Further research is necessary to validate the results with other devices and to generalize the methodology for field assessment.

Acoustic imaging can be performed using a spherical microphone array (SMA) and conventional beamforming (CBF) or spherical harmonic beamforming (SHB). At low frequencies, the mainlobe width depends on the SMA radius for CBF and on the order of the spherical harmonics expansion for SHB, which is related to the number of microphones. In this letter, Kriging is used to virtually increase the SMA radius and/or the number of microphones. Numerical and experimental investigations show the effectiveness of Kriging to reduce the mainlobe width and thus improve the acoustic images obtained with a SMA and CBF or SHB.

Offering hearing protection devices (HPDs) to workers exposed to hazardous noise is a noise control strategy often used to prevent noise-induced hearing loss (NIHL). However, HPDs are used incorrectly and inconsistently, which explains their limited efficiency. Numerous models based on social cognition theories identify the significant factors associated with inconsistent HPD use and aim to improve HPD training programs and to increase HPD use. However, these models do not detail (dis)comfort aspects originating from complex interactions between characteristics of the triad “environment/person/HPD” while these aspects are known to largely influence HPD (mis)use. This paper proposes a holistic model explaining HPD (mis)use, based on the integration of a comfort model adapted to HPDs into an existing behavioral model already developed for HPDs. The model also takes into account the temporal dimension, which makes it possible to capture the scope of change in HPD-related health behaviors. This holistic description of HPD use could be used as a tool for stakeholders involved in HPD use to effectively prevent NIHL among workers.

The sound attenuation of double hearing protectors (DHPs), earplugs combined with earmuffs, generally falls short of the sum of each single protector's attenuation when used independently. This phenomenon, referred to as the DHP effect, is found to be related to structure-borne sound transmission involving the outer ear and can also be observed on acoustic test fixtures (ATFs). At present, it still remains not fully understood, and no available model can help demonstrate the associated sound transmission mechanisms. In this work, a finite element model is proposed to study the DHP effect on an ATF between 100 Hz and 5 kHz. Power balances are calculated with selected configurations of the ATF in order to (i) quantify the contribution of each sound path, and study the effects of (ii) the artificial skin and (iii) acoustic excitation on the ATF exterior boundaries. The DHP effect is shown to originate from the structure-borne sound power injected from the ATF boundaries and/or earmuff cushion. The important influence of earcanal wall vibration is highlighted when the skin is accounted for. The simulation results allow for gaining more insight into the sound transmission through a DHP/ATF system.

Objective. This article proposes a comprehensive literature review of past works addressing hearing protection device (HPD) comfort with the aim of identifying the main sources of variability in comfort evaluation. Methods. A literature review of study samples was performed: documents were hand searched and Internet searched using PubMed, Web of Science, Google Scholar, ProQuest Dissertations and Theses Professional, Scopus or Google search engines. While comfort constructs and measurement methods are reviewed for both earplugs and earmuff HPD types, results and analyses are provided for earplugs only. Results. The literature shows that the multiple sources of the perceived comfort measurement variability are related to the complexity of the concept of comfort and to the various physical and psychosocial characteristics of the triad 'environment/person/earplug', which differ from one study to the other. Conclusions. Considering the current state of knowledge and in order to decrease comfort measurements variability, it is advised to: (a) use a multidimensional construct of comfort and derive a comfort index for each comfort dimension;, (b) use exhaustive and valid questionnaires; (c) quantify as many triad characteristics as possible and use them as independent or control variables; (d) assess the quality of the earplug fitting and the attenuation efficiency.

The occlusion effect is an acoustic discomfort commonly encountered by earplugs’ users, which corresponds to the increased auditory perception of the bone-conducted sound mainly at low frequencies. This perception is accompanied by the augmentation of the sound pressure level in the earcanal when occluded by the earplug compared to the open case. While the source of the SPL generated in the earcanal in both open and occluded cases is mainly attributed to the vibration of the earcanal wall, the sound radiation of the tympanic membrane that stems from the middle ear vibration is commonly considered as not significant. To investigate this phenomenon, a finite element model that incorporates the middle ear components into a realistic human outer ear is developed. First, the finite element model is evaluated by comparing the acoustic impedance computed at the eardrum surface to literature data obtained on human subjects. Second, the finite element model is used to quantify the contribution of the sound radiation that originates from the middle ear on the sound pressure level generated in both open and occluded earcanals under a bone-conducted stimulation.

Blocking the earcanal’s entrance with an earplug can lead users to experience discomforts, one being the occlusion effect (OE), typically described as a distorted perception of one’s own voice. This discomfort sometimes causes users to misuse or remove their earplugs which significantly lower their efficiency. Reducing the OE generated by earplugs is therefore critical to make them more comfortable. However, assessing the OE is cumbersome and time-consuming as participants’ feedback is required. Moreover, the influence of factors on the OE, namely, the type or earplug, the insertion depth, and the background noise level, remains to be understood. Hence, this ongoing research aims at objectivizing the OE induced by earplugs during speech. To do so, the OE is assessed in laboratory conditions with 30 normal hearing participants using a questionnaire and by using surrogate earplugs for in-ear microphonic measurements. Various sound pressure level-based indicators are proposed and correlated to the (dis)comfort during the objectivization step. Multiple combinations of earplugs, insertion depths and background noise levels are tested to obtain a ranking of the conditions generating more or less OE. The objectivization of the OE will be a useful tool for manufacturers developing new earplugs without requiring participants’ feedback.

The IEC 60318-4 ear simulator is used to measure the insertion loss (IL) of earplugs in the ear canal of an acoustical test fixture (ATF) and is designed to represent an average acoustic impedance (in a reference plane) of the human ear. The ear simulator is usually modeled using a lumped parameter model (LPM) which has frequency limitations and inadequately accounts for the thermo-viscous effects in the simulator. The simulator numerical models that can better deal with the thermo-viscous phenomena often lack essential geometric details. Most related studies also suffer from the lack of experimental validation of the models. Therefore, a transfer matrix (TM) model of the IEC 60318-4 simulator is proposed based on a direct assessment of its geometric dimensions. Such a model is of particular interest for designing artificial ear simulators. The variability in the simulator impedance due to the geometric uncertainties is quantified using the Monte Carlo method. The TM model is validated using i) a finite element (FE) model of the simulator and ii) impedance measurements with a sound intensity probe. It is found to better describe the simulator impedance above 3 kHz compared to the LPM. The TM model is then coupled to a FE model of an occluded ATF ear canal to simulate the IL of an earplug in the frequency range [100 Hz, 10 kHz]. In the model, the simulator is considered as a cylindrical cavity terminated by an equivalent tympanic impedance which is determined from the TM model to simulate the sound pressure measured at the real microphone position (not at the reference plane) in the ATF ear canal. The simulated IL is validated against i) that obtained with a complete FE model of the corresponding system and ii) measurements using an ATF. The TM model is shown to better agree with the simulator FE model than the LPM above 6 kHz regarding the earplug IL simulated using this method.

Many workers are exposed daily to excessive noise levels. In order to reduce the noise exposure at the workstation, the main noise sources have to be detected. This task can be done with a microphone array and a source localization technique. Previous studies have shown promising results with time domain beamforming based on the generalized cross-correlation technique. The objective of this work is to propose an optimal spherical microphone array geometry dedicated to this technique. A cost function based on the symmetry of the aperture angle maps is proposed and is maximized using a Nonlinear Optimization by Mesh Adaptive Direct Search. Numerical results show that the optimized geometry improves the noise source map by reducing the side lobe amplitude without increasing the main lobe surface. Experimental measurements are carried out in a semi-anechoic chamber with prototyped spherical microphone arrays confirming that the optimized microphone array improves the quality of the noise source map.

Objective: This article presents a comprehensive literature review of past works addressing Hearing Protection Devices (HPD) comfort and to put them into perspective regarding a proposed holistic multidimensional construct of HPD comfort.Design: Literature review.Study samples: Documents were hand searched and Internet searched using "PubMed", "Web of Science", "Google Scholar", "ProQuest Dissertations and Theses Professional", "Scopus" or "Google" search engines. While comfort constructs and measurement methods are reviewed for both earplugs and earmuff types, results and analyses are provided for the earplug type only.Results: This article proposed a multidimensional construct of HPD comfort based on four dimensions: physical, functional, acoustical and psychological. Seen through the prism of the proposed holistic construct of HPD comfort, the main comfort attributes of earplugs have been identified for each comfort dimension.Conclusions: The observed lack of consensus on the definition of HPD comfort in the scientific community makes it difficult to prioritise the importance of comfort attributes yet necessary for future design of comfortable earplugs.

The generalized cross correlation (GCC) is an efficient technique for performing acoustic imaging. However, it suffers from important limitations such as a large main lobe width for noise sources with low frequency content or a high amplitude of side lobes for noise sources with high frequencies. Prefiltering operation of the microphone signals by a weighting function can be used to improve the acoustic image. In this work, two weighting functions based on PHAse Transform (PHAT) improvements are used. The first adds an exponent to the PHAT expression (ρ-PHAT), while the second adds the minimum value of the coherence function to the denominator (ρ-PHAT-C). Numerical acoustic images obtained with the GCC and those weighting functions are compared and quantitatively assessed thanks to a metric based on a covariance ellipse, which surrounds either the main lobe or the side lobes. The weighting function ρ-PHAT-C provides the smallest surface ellipses especially when the arithmetic of the GCC is replaced by the geometric mean (GEO). Experimental measurements are carried out in a hemi-anechoic room and a reverberant chamber where two loudspeakers were set in front of microphone array. The acoustic images obtained confirm that the ρ-PHAT-C with the GEO outperforms the GCC, GCC-PHAT, and GCC ρ-PHAT.

The objective occlusion effect induced by bone-conducted stimulation refers to the low frequency acoustic pressure increase that results from occluding the ear canal opening. This phenomenon is commonly interpreted as follows: the bone-conducted sound “leaks” through the earcanal opening and is “trapped” by the occlusion device. This instinctive interpretation misrepresents the fundamental mechanism of the occlusion effect related to the earcanal impedance increase and already highlighted by existing electro-acoustic models. However, these models simplify the earcanal wall vibration (i.e., the origin of the phenomenon) to a volume velocity source which, in the authors' opinion, (i) hinders an exhaustive comprehension of the vibro-acoustic behavior of the system, (ii) hides the influence of the earcanal wall vibration distribution, and (iii) could blur the interpretation of the occlusion effect. This paper analyzes, illustrates, and interprets the vibro-acoustic behavior of the open and occluded earcanal using an improved finite element model of an outer ear in conjunction with an associated electro-acoustic model developed in this work. The two models are very complementary to dissect physical phenomena and to highlight the influence of the earcanal wall vibration distribution, characterized here by its curvilinear centroid position, on the occlusion effect.

In this paper, the vibro-acoustic response of a passive earmuff in a broadband frequency range (100 Hz to 5 kHz) is investigated using a finite element analysis. Firstly, the study focuses on the vibro-acoustic response of the cup and the back-plate regardless of the comfort cushion contribution. Secondly, emphasis is put on the foam-filled comfort cushion which is the trickiest component to model because of its physical complexity. This multiphasic cushion is modeled in a simplified way as an equivalent solid, either isotropic or transverse isotropic in order to take into account the added transverse stiffness due to the bulging of the cushion polymeric sheath. The accuracy of these models is investigated by comparing the simulated insertion loss (IL) to measurement data. The IL predicted with the isotropic cushion model is highly underestimated between 500 Hz and 2.5 kHz due to the presence of an unrealistic mode of transverse deformation. It is found that (i) neglecting the acoustic excitation on the cushion’ external flanks of the isotropic model or (ii) using the transverse isotropic cushion model significantly improves the simulated IL.

The occlusion effect is commonly experienced as the altered perception of one’s own physiological noise when the earcanal entrance is blocked. Objectively, this phenomenon corresponds to an acoustic pressure increase in the occluded earcanal. The occlusion effect originates from the earcanal wall normal vibration and depends on the spatial distribution of the latter. At low frequencies, this spatial distribution can be characterized by the position of its centroid along the earcanal middle axis. This paper describes the principle of an acoustical method for estimating this centroid position at low frequencies. The proposed method consists in measuring the eardrum acoustic pressure transfer function between the earcanal open and occluded by an external capped duct coupled to the earcanal entrance of a subject submitted to a bone-conducted stimulation. The centroid position is then estimated at the antiresonance frequency of the coupled system using an associated electro-acoustic model. The proposed method is evaluated and investigated numerically using a 3D finite element model of an outer ear. The sensitivity of the method is shown to increase with frequency. To maximize the method accuracy, the radius of the coupling duct must be as large as possible (in the limits of the earcanal entrance dimension) and any incomplete seal between the duct and the earcanal entrance must be avoided. Also, the coupling position of the duct and its temperature must be known as precisely as possible. On the contrary, the proposed method does not require the knowledge of the eardrum acoustic impedance.

This paper addresses source localization technique in time domain for broadband acoustic sources. The objective is to accurately and quickly detect the position and amplitude of noise sources in workplaces in order to propose adequate noise control options and prevent workers hearing loss or safety risk. First, the generalized cross correlation associated with a spherical microphone array is used to generate an initial noise source map. Then a linear inverse problem is defined to improve this initial map. Commonly, the linear inverse problem is solved with an l 2 -regularization. In this study, two sparsity constraints are used to solve the inverse problem, the orthogonal matching pursuit and the truncated Newton interior-point method. Synthetic data are used to highlight the performances of the technique. High resolution imaging is achieved for various acoustic sources configurations. Moreover, the amplitudes of the acoustic sources are correctly estimated. A comparison of computation times shows that the technique is compatible with quasi real-time generation of noise source maps. Finally, the technique is tested with real data.

Poroelastic models are constructed based on a set of physical parameters known as the Biot’s parameters (for isotropic materials these are comprised of 5 non-acoustical parameters and 4 mechanical parameters). These macroscopic properties are inter-correlated and dependent on the microstructure of the foam. Therefore, to optimize vibroacoustic behavior, the correlation between foam microstructure and macroscopic properties is needed. In this study, the effect of closed windows content (known as reticulation rate), cell size, and relative density on the mechanical properties of polyurethane (PU) foam are numerically studied using an isotropic, tetrakaidecahedral unit cell. Then, an existing analytical model that correlates unit cell microstructure properties (thickness and length of struts) of fully reticulated foams to their mechanical properties is extended numerically. The membrane thickness is considered to be thinner at the center and larger at the edge of the window. The ratio of membrane thickness to strut thickness is either considered to be fixed or variable. Results show that the Young’s modulus and Poisson’s ratio of unit cells with smaller cells size, when relative density is fixed, are more affected by closed window content.

International audience; In-ear devices are used in a wide range of applications for which the device's usability and/or efficiency is strongly related to comfort aspects that are influenced by the mechanical interaction between the device and the walls of the earcanal. Although the displacement of the earcanal walls due to the insertion of the device is an important characteristic of this interaction, existing studies on this subject are very limited. This paper proposes a method to estimate this displacement in vivo using a registration technique on magnetic resonance images. The amplitude, the location and the direction of the earcanal wall displacement are computed for four types of earplugs used by one participant. These displacements give indications on how each earplug deforms the earcanal for one specific earcanal geometry and one specific earplug insertion. Although the displacement due to a specific earplug family cannot be generalized using the results of this paper, the latter help to understand where, how much, and how each studied earplug deforms the earcanal of the participant. This method is revealed as a promising tool to investigate further acoustical and physical comfort aspects of in-ear devices.

Nowadays, acoustic cameras have become a standard tool for visualizing sound sources. The main post-processing techniques for generating acoustic images are associated with beamforming in the time or frequency domain. While many advanced techniques have been developed for the latter in order to achieve high resolution, such as deconvolution or inverse methods, the former have been less investigated. Recent studies have shown that time-domain beamforming can provide a narrow main lobe with low side lobe levels in different situations. However, a comparison of both techniques in terms of acoustic imaging does not exist. This paper provides a detailed comparison of conventional frequency-domain beamforming (CBF) and time-domain beamforming based on the generalized cross-correlation technique (GCC). First, numerical data are used for assessing both techniques. Then, experimental tests are carried out in a hemi-anechoic room using loudspeakers or power tools. As expected, acoustic images provided by CBF and GCC are found to be very similar but with different computation times. In order to improve the acoustic image, advanced techniques are considered (Clean-SC and the GCC based on geometric mean). When dealing with low frequency, Clean-SC is not able to detect both sources while the GCC based on geometric mean provides an accurate source separation.

Double hearing protectors (DHPs), earplugs and earmuffs worn in combination, may be needed in high level noise environments. The DHP sound attenuation is known to be less than the sum of each single protector attenuation. This effect, referred to as the DHP effect, is still not fully understood. A recent study has shown that it can be observed on an acoustic test fixture (ATF) and characterized by the decrease of the earplug noise reduction (NR) when the earmuff is added. In this paper, a measurement methodology is proposed to (i) identify the main sound paths related to the DHP effect on an ATF and (ii) explain the latter by the relative contributions of the air-borne and structure-borne transmissions in the system. The focus is put on the NR values of the earplug alone and in the DHP. Measurement results suggest that the DHP effect is related to the energy transmitted from the earcup, through the earmuff cushion and finally into the earcanal via the sound radiation of the earplug and/or earcanal lateral walls. This flanking structure-borne path is found to dominate over the “direct” air-borne path through the hearing protectors at frequencies above 300 Hz.

The occlusion effect is commonly experienced by in-ear device wearers as an increased loudness sensation of bone-conducted low frequency sounds. A widespread theory proposed by Tonndorf and based on a simplified electro-acoustic model describes the phenomenon as the removal of the open earcanal high-pass filter effect due to a perfect or partial occlusion. However, this filter has not been clearly defined and several ambiguities remain. Revisiting the model, a second order high-pass filter effect for the volume velocity transferred between the earcanal wall and the eardrum is highlighted. This filter remains for partial occlusion but vanishes for perfect occlusion. In the latter case, the volume velocity transferred from the earcanal cavity to the middle ear through the eardrum drastically increases, which explains the predominance of the occluded outer ear pathway on the hearing by bone-conduction at low frequencies.

For people working in high noise level environments, typically above 105 dBA, double hearing protection (DHP) systems (earplugs worn in combination with earmuffs) are always recommended. However, it is very difficult to predict the DHP overall sound attenuation due to the complexity of the system. A recent experimental study has shown on human subjects and an acoustic test fixture (ATF) that the noise reduction (NR) of the earplug decreases considerably when an earmuff is worn over it but the reason is still not fully understood. In this work, specially designed experiments using an ATF are proposed in order to explain this observation. The focus is put on the NR of the single earplug and that of the earplug in the DHP system. The respective effects on the DHP attenuation of various sound transmission paths involved in the system (both air-borne and structure-borne) are analyzed by modifying the system coupling conditions or controlling the sound pressure level under the earmuff. This work will help better understand the interactions between the system components and will provide the grounds for developing a prospective numerical model to predict the sound attenuation of a DHP system.

Offering hearing protection devices (HPDs) to workers exposed to hazardous noise is a common noise control strategy for preventing noise-induced hearing loss (NIHL). However, HPDs are not always worn, or are used incorrectly and inconsistently by workers, which explains their limited efficiency. Numerous models based on social cognition theories aim to improve hearing protection training programs and to increase HPD use. They identify significant factors associated with worker’s behaviors regarding HPD use (e.g., perceived barriers and benefits to HPD use, perceived self-efficacy). However, these models do not detail (dis)comfort aspects originating from complex interactions between physical characteristics of the triad “user/HPD/work environment” while these aspects are known to largely influence HPD (mis)use. The objective of this communication is to propose a metatheory explaining HPD (mis)use and based on the integration of an HPD comfort model into an existing social cognition model already developed for HPDs. This holistic description of the HPD use, involving both physical and psychosocial characteristics of the triad, could be used as a tool for the stakeholders (e.g., researchers, manufacturers, preventers) involved in the protection of workers from NIHL.

Porous materials are widely used for improving sound absorption and sound transmission loss of vibrating structures. However, their efficiency is limited to medium and high frequencies of sound. A solution for improving their low frequency behavior while keeping an acceptable thickness is to embed resonant structures such as Helmholtz resonators (HRs). This work investigates the absorption and transmission acoustic performances of a cellular porous material with a two-dimensional periodic arrangement of HR inclusions. A low frequency model of a resonant periodic unit cell based on the parallel transfer matrix method is presented. The model is validated by comparison with impedance tube measurements and simulations based on both the finite element method and a homogenization based model. At the HR resonance frequency (i) the transmission loss is greatly improved and (ii) the sound absorption of the foam can be either decreased or improved depending on the HR tuning frequency and on the thickness and properties of the host foam. Finally, the diffuse field sound absorption and diffuse field sound transmission loss performance of a 2.6 m(2) resonant cellular material are measured. It is shown that the improvements observed at the Helmholtz resonant frequency on a single cell are confirmed at a larger scale.

This paper compares different approaches to model the vibroacoustic behavior of earmuffs at low frequency and investigates their accuracy by comparison with objective insertion loss measurements recently carried out by Boyer et al. [(2014). Appl. Acoust. 83, 76-85]. Two models based on the finite element (FE) method where the cushion is either modeled as a spring foundation (SF) or as an equivalent solid (ES), and the well-known lumped parameters model (LPM) are investigated. Modeling results show that: (i) all modeling strategies are in good agreement with measurements, providing that the characterization of the cushion equivalent mechanical properties are performed with great care and as close as possible to in situ loading, boundary, and environmental conditions and that the frequency dependence of the mechanical properties is taken into account, (ii) the LPM is the most simple modeling strategy, but the air volume enclosed by the earmuff must be correctly estimated, which is not as straightforward as it may seem, (iii) similar results are obtained with the SF and the ES FE-models of the cushion, but the SF should be preferred to predict the earmuff acoustic response at low frequency since it requires less parameters and a less complex characterization procedure.

In order to understand the acoustic behavior of porous membranes, there is a need to further investigate the link between microstructure and macroscopic properties of such materials. This study presents the sound absorption properties of a novel bimodal foam structure made of polylactide (PLA) with an interconnected network of pores and micropores of very different characteristic sizes, fabricated utilizing the blend of PLA and polyethylene glycol (PEG) water soluble polymer. Fabricated foams are bio-based and have the advantage of resolving the environmental concerns raised by petrochemical based sound absorbers. The purpose of this study is to develop bio-based open cell structures as a practical solution to today’s needs for noise control resolutions. Acoustic performance of the bimodal PLA foams is studied by measuring the normal incident absorption coefficient and the effect of bimodal structure is investigated in terms of acoustic properties (i.e., sound absorption) and non-acoustic properties associated to the Johnson–Champoux–Allard model (i.e., porosity, airflow resistivity, tortuosity, …). Inverse method based on JCA model and impedance tube measurements for normal incident absorption coefficient was applied to estimate tortuosity and characteristic lengths. Results of inverse method are in good agreement with direct measurements of normal incident absorption coefficient. While tortuosity increases by increasing the polymer weight percent, it remains constant as the secondary porous structure extends in the porous medium. As the bimodal structure extends through the foam, both thermal and viscous characteristic lengths increase for different foam categories.

Passive and active in-ear devices (IED) occluding the ear canal are commonly used to (i) protect people from high noise levels (earplugs), (ii) assist people suffering from hearing impairment (hearing aids) or (iii) help people in listening from their sound systems (earbuds). However, the usability and/or efficiency of IEDs can be greatly affected by several discomfort components (physical, acoustical and functional). The mechanical pressure exerted by the IED onto the ear canal walls is greatly suspected to affect the aforementioned comfort components. This physical characteristic is closely related to the displacement field induced by the IED insertion, which has to be known for a better understanding of perceived discomfort. Thus, this paper proposes to validate a method based on medical images to estimate the displacement field of the ear canal walls due to the insertion of an IED. The approach is validated on a human-like artificial ear with canal geometry deformed using two custom molded IEDs with controlled shapes. These geometries are obtained using computed tomography imaging and the displacement field is computed using a registration method. The errors due to the ear canal segmentation and to the registration steps are small enough to compute a relevant estimation of the expected displacement field. Results show that the amplitude of the displacement and its location into the ear canal can be evaluated with an accuracy of ± 0.2 mm and ± 0.4 mm respectively. Preliminary results on images with a degraded resolution indicate that the proposed approach used to assess the displacement field of the ear canal walls using computed tomography images could be applied on magnetic resonance images, which is a preferred method to image human subject ear canals for future investigations.

International audience; Millions of workers are exposed to excessive noise levels each day. Acoustic solutions have to be developed to protect workers from hearing loss. The first step of an acoustic diagnosis is the source localization which can be performed with a microphone array. Spherical microphone arrays can be used to detect the acoustic source positions in a workplace. In this study, a spherical microphone array, with polyhedral discretization, is proposed and compared with a spherical array with a slightly different geometry. The generalized cross-correlation technique is used to detect the source positions. Moreover, two criteria are introduced to improve the noise source map. The first is based on the geometric properties of the microphone array and the scan zone whereas the second is based on the energy of the spatial likelihood function. Numerical data are used to provide a systematic comparison of both geometries and criteria. Finally, experiments in a reverberant room reveal that the polyhedral microphone array associated with both criteria provide the best noise source map.

International audience; This paper deals with the prediction of the macroscopic sound absorption behavior of highly porous polyurethane foams using two unit-cell microstructure-based models recently developed by Doutres, Atalla, and Dong [J. Appl. Phys. 110, 064901 (2011); J. Appl. Phys. 113, 054901 (2013)]. In these models, the porous material is idealized as a packing of a tetrakaidecahedra unit-cell representative of the disordered network that constitutes the porous frame. The non-acoustic parameters involved in the classical Johnson-Champoux-Allard model (i.e., porosity, airflow resistivity, tortuosity, etc.) are derived from characteristic properties of the unit-cell and semi-empirical relationships. A global sensitivity analysis is performed on these two models in order to investigate how the variability associated with the measured unit-cell characteristics affects the models outputs. This allows identification of the possible limitations of a unit-cell micro-macro approach due to microstructure irregularity. The sensitivity analysis mainly shows that for moderately and highly reticulated polyurethane foams, the strut length parameter is the key parameter since it greatly impacts three important non-acoustic parameters and causes large uncertainty on the sound absorption coefficient even if its measurement variability is moderate. For foams with a slight inhomogeneity and anisotropy, a micro-macro model associated to cell size measurements should be preferred.

This paper proposes an objective measurement methodology to assess the sound transmission paths through various earmuff components (cup, cushion, back-plate, foam insert, silicone flesh) and estimate the vibroacoustic couplings between them. The measurement methodology is applied to two different commercial earmuffs. For each Hearing Protection Device (HPD), the different sound paths are assessed, by analyzing separately the vibroacoustic behavior of each HPD component. In particular, the Insertion Loss (IL) of the lateral walls of the cushion is assessed, with and without pumping motion. The effect of the coupling between the different parts is also investigated from the comparison of the separate components with the complete earmuff. As shown in past studies, results confirm that the acoustical behavior of an earmuff is governed by the pumping motion and air leaks at low frequency and by the sound path through the cup and the cavity resonances at high frequency. However, at mid frequency, new counter-intuitive results are revealed. It is found that earmuffs do not behave as their weakest element, but rather as the one which has the highest attenuation. It is also observed that the foam insert can also decrease the IL. Complementary tests using other absorbing materials show that this effect could mainly be attributed to the absorption behaviors of each material at medium frequencies.

Producing closed-cell foams is generally cheaper and simpler than open-cell foams. However, the acoustic and filtration efficiency of closed-cell foam materials is generally poor because it is very difficult for fluid or acoustic waves to penetrate into the material. A new method using shock waves to remove the membranes closing the cell pores (known as reticulation) and thus to improve the acoustic and filtration behavior of closed-cell foam material is presented. Various shock treatments have been carried out on polyurethane and polyimide foams and the following conclusions were drawn: (1) reticulation efficiency increased and thus the airflow resistivity and tortuosity decreased when increasing the amplitude of the shock treatment; (2) the rigidity of the foam is decreased; (3) the process is reliable and repeatable and (4) obtained acoustic performance is comparable to classical thermal reticulation.

International audience; Acoustic performances of two concepts based on the integration of an elastic membrane in the front wall of a cavity and Helmholtz resonator embedded in a melamine matrix are studied. Membranes are made of acrylic material, this latter is first characterized with a uniaxial test in order to extract the mechanical properties needed to model the membrane. Analytical, numerical and experimental investigations are performed so as to determine the acoustical potential of the proposed systems in terms of absorption and transmission loss. The contribution to the sound absorption can be positive or negative at the resonator resonances, an analytical model is proposed to highlight the physical phenomena related to these effects. In addition, a multiphysics numerical model combining the acoustic-mechanical interaction has been developed and validated by comparison with the experimental data measured using an impedance tube. The studied concepts could other significant enhancements of sound transmission loss properties in the low frequencies but also on acoustic absorption in specific frequency bands.

Microphone array techniques are an efficient tool to detect acoustic source positions. The delay and sum beamforming is the standard method. In the time domain, the generalized cross-correlation can be used to compute the noise source map. This technique is based on the arithmetic mean of the spatial likelihood functions. In this study, the classical arithmetic mean is replaced by the more standard generalized mean. The noise source maps provide by the arithmetic, geometric and harmonic means are compared in the case of numerical and experimental data obtained in a reverberant room. The geometric and harmonic means provide the best noise source maps with no side lobes and a better source level estimation.

Complement to standard E2611-09 of the American Society for Testing and Materials [Standard Test Method for Measurement of Normal Incidence Sound Transmission of Acoustical Materials Based on the Transfer Matrix Method (American Society for Testing and Materials, New York, 2009)] is proposed in order to measure normal incidence sound transmission loss of materials in a modified impedance tube using a three-microphone two-load or one-load method. The modified tube is a standard two-microphone impedance tube, where a third microphone is mounted on a movable hard termination. This method is conceptually identical to the four-microphone two-load or one-load method described in the standard; however, it requires fewer transfer functions and one microphone less. The method is validated on (1) symmetrical homogeneous and (2) non-symmetrical non-homogeneous specimens.

The objective of this paper is to propose a practical impedance tube method to optimize the sound transmission loss of double wall structure by concentrating on the sound package placed inside the structure. In a previous work, the authors derived an expression that breakdown the transmission loss of a double wall structure containing a sound absorbing blanket separated from the panels by air layers in terms of three main contributions; (i) sound transmission loss of the panels, (ii) sound transmission loss of the blanket and (iii) sound absorption due to multiple reflections inside the cavity. The sound transmission loss contributions of the blanket can thus be estimated from three acoustic measurements using impedance tube techniques: two reflection coefficients at the front face and the rear face of the blanket placed in specific positions characteristic of its position inside the double wall structure and its sound transmission coefficient. The method is first validated in the case of a double wall structure filled with a 2 in. foam material. Next, it is applied to investigate (i) the effect of frame compression of a 2 in. fibre glass in an aeronautic-type double wall structure and (ii) the effect of double porosity with or without porous inclusions in a building-type double wall structure.

Novel flexible polyurethane foams were successfully prepared from a renewable source, hydroxytelechelic natural rubber (HTNR) having different molecular weights (1000–3400 g mol−1) and variation of epoxide contents (EHTNR, 0–35% epoxidation) by a one-shot technique. The chemical and cell structures as well as physico-mechanical, thermal, and acoustic properties were characterized and compared with commercial polyol analogs. The obtained HTNR based foams are open cell structures with cell dimensions between 0.38 and 0.47 mm. The HTNR1000 based foam exhibits better mechanical properties but lower elongation at break than those of commercial polyol analog. However, the HTNR3400 based foam shows the best elastic properties. In a series of EHTNR based foams, the tensile and compressive strengths show a tendency to increase with increasing epoxide content and amount of 1,4-butanediol (BD). The HTNR based foams demonstrate better low temperature flexibility than that of the foam based on commercial polyol. Moreover, the HTNR based polyurethane foams was found to be an excellent absorber of acoustics. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010

Earplugs are a usual way to protect workers subjected to noise exposure. However, the efficiency of these hearing protection devices is often affected by induced discomforts. A factor suspected to impact both acoustical and physiological comfort attributes of earplugs is the deformation they apply on the ear canal walls. As the geometry of both open and occluded ear canal is difficult to obtain, the ear canal deformation due to earplug insertion is not trivial to evaluate. Current medical imaging techniques and image post-processing methods are promising tools to investigate this deformation. In a previous study of the authors, an approach using registration methods on medical images had been proposed to estimate the ear canal displacement field induced by earplug insertion. This approach had been validated in the case of computed tomography scans of a human-like artificial ear occluded by a controlled-shape custom molded earplug. In the present study, this approach is used to evaluate the ear canal displ...

For several years, lack of comfort has been pointed out as a major reason of earplug poor efficiency as noise control solution. The great complexity of comfort makes it difficult to predict it in the earplugs design phase. It is rather considered in an empirical way by the manufacturers using trial-and-errors approaches based on subjective assessment over a panel of subjects. Furthermore, because comfort is not quantified, Occupational Health and Safety (OHS) practitioners cannot select earplugs ensuring wearer comfort. To address these issues, a major international research project funded by two OHS institutes (IRSST in Canada and INRS in France) and involving several Universities (in Canada and England) started in 2017. The main objectives are to: (1) improve the understanding of earplugs comfort as perceived by field workers with consideration of all comfort components, (2) develop laboratory tools (augmented experimental and virtual artificial heads) to measure physical design variables related to the auditory, physiological, and functional components of comfort and (3) design a battery of hybrid objective/subjective comfort indices to quantify / measure / predict the different components of comfort. The aim of this presentation will be to present the project and first results.For several years, lack of comfort has been pointed out as a major reason of earplug poor efficiency as noise control solution. The great complexity of comfort makes it difficult to predict it in the earplugs design phase. It is rather considered in an empirical way by the manufacturers using trial-and-errors approaches based on subjective assessment over a panel of subjects. Furthermore, because comfort is not quantified, Occupational Health and Safety (OHS) practitioners cannot select earplugs ensuring wearer comfort. To address these issues, a major international research project funded by two OHS institutes (IRSST in Canada and INRS in France) and involving several Universities (in Canada and England) started in 2017. The main objectives are to: (1) improve the understanding of earplugs comfort as perceived by field workers with consideration of all comfort components, (2) develop laboratory tools (augmented experimental and virtual artificial heads) to measure physical design variables related to the...

International audience; Damping using an instability of a fluid film in contact with a vibrating structure is investigated. Waves induced in the fluid film are the source of the added damping. A model based on the theory of Faraday instability is applied to a clamped circular plate covered by a fluid film. It is shown that this original technique can provide a significant damping, as with viscoelastic or porous material treatments. It is related to the amplitude of the waves which is a non linear function of the plate acceleration. Theoretical and experimental results are compared. The model overestimates the added damping: it is four times greater than the measured one.

International audience; This paper investigates the feasibility to use an electrodynamic loudspeaker to determine viscoelastic properties of sound absorbing materials in the audible frequency range. The loudspeaker compresses the porous sample in a cavity and a measurement of its electrical impedance allows to determine the mechanical impedance of the sample: no additional sensors are required. Viscoelastic properties of the material are then estimated by inverting a 1D Biot model. The method is applied to two sound absorbing materials (glass wool and polymer foam). Results are in good agreement with classical compression quasistatic method.

Foam microstructure can be seen as a collection of interlinked struts forming a packing of cells interconnected to others through pores. Materials with a totality of pores closed by thin membranes are called closed-cell foams. The filtration and acoustic efficiency of closed-cell foams is poor compared to open-cell foams since it is very difficult for the fluid or the acoustic waves to penetrate inside the material.

Broadband noise absorption, including low frequencies, may be obtained by a hybrid passive-active two-layer system. A porous layer in front of an air layer provides passive absorption, at medium and high frequencies. Active control of the input impedance of the two-layer system yields absorption at low frequencies. The active control system can implement either pressure-release or impedance-matching conditions. A simple analytical model based upon plane waves propagating in a tube permits the comparison of both control strategies. The results of this simple model show that the pressure-release condition affords higher absorption than the impedance-matching condition for some combinations of geometrical and material parameters. Experimental results corroborate the good performance of the pressure-release condition under the prescribed geometrical setup.

Microphone array techniques are an efficient tool to detect acoustic source positions. The standard technique is the delay and sum beamforming. In the time domain, the generalized cross correlation of the microphone signals is used to compute the Spatial Likelihood Functions (SLF) of all microphone pairs and the noise source map is provided by the arithmetic mean of these functions. To improve the former noise source map, which means narrowing the main lobe and removing side and spurious lobes, several techniques have been developed in the past. In this work, the performances of three of these techniques (in terms of source position detection, amplitude estimation and computation time) are compared in the case of both synthetic and real data: (1) energetic and geometric criteria are applied in order to remove the SLF with useless information, (2) the arithmetic mean is replaced by the generalized mean and (3) linear inverse problem is solved with sparsity constraint. In the case of real data, the source t...