Search

Ferroelectric hafnium zirconium oxide holds great promise for a broad spectrum of complementary metal-oxide-semiconductor (CMOS) compatible and scaled microelectronic applications, including memory, low-voltage transistors, and infrared sensors, among others. An outstanding challenge hindering the implementation of this material is polarization instability during field cycling. In this study, the nanoscale phenomena contributing to both polarization fatigue and wake-up are reported. Using synchrotron X-ray diffraction, the conversion of non-polar tetragonal and polar orthorhombic phases to a non-polar monoclinic phase while field cycling devices comprising noble metal contacts is observed. This phase exchange accompanies a diminishing ferroelectric remanent polarization and provides device-scale crystallographic evidence of phase exchange leading to ferroelectric fatigue in these structures. A reduction in the full width at half-maximum of the superimposed tetragonal (101) and orthorhombic (111) diffraction reflections is observed to accompany wake-up in structures comprising tantalum nitride and tungsten electrodes. Combined with polarization and relative permittivity measurements, the observed peak narrowing and a shift in position to lower angles is attributed, in part, to a phase exchange of the non-polar tetragonal to the polar orthorhombic phase during wake-up. These results provide insight into the role of electrodes in the performance of hafnium oxide-based ferroelectrics and mechanisms driving wake-up and fatigue, and demonstrate a non-destructive means to characterize the phase changes accompanying polarization instabilities.

Electricity from thermal sources It is desirable to harvest as much energy as possible from processes that produce useful amounts of heat and convert it from waste into electrical power. Thermoelectrics and thermophotovoltaics can harness and convert heat waste but tend to operate at high temperatures. Davids et al. designed and fabricated a complementary metal-oxide semiconductor infrared photonic device that can harvest and recover energy from low-temperature thermal sources (see the Perspective by Raman). Using a new conversion mechanism, they experimentally demonstrate large thermal-to-electrical power generation in a bipolar grating-coupled tunneling device, rivaling the best thermoelectric devices. The device design could be used for energy harvesting of waste heat and the development of compact thermal batteries. Science , this issue p. 1341 ; see also p. 1301

Integrated photonics will play a key role in quantum systems as they grow from few-qubit prototypes to tens of thousands of qubits. The underlying optical quantum technologies can only be realized through the integration of these components onto quantum photonic integrated circuits (QPICs) with accompanying electronics. In the last decade, remarkable advances in quantum photonic integration have enabled table-top experiments to be scaled down to prototype chips with improvements in efficiency, robustness, and key performance metrics. These advances have enabled integrated quantum photonic technologies combining up to 650 optical and electrical components onto a single chip that are capable of programmable quantum information processing, chip-to-chip networking, hybrid quantum system integration, and high-speed communications. In this roadmap article, we highlight the status, current and future challenges, and emerging technologies in several key research areas in integrated quantum photonics, including photonic platforms, quantum and classical light sources, quantum frequency conversion, integrated detectors, and applications in computing, communications, and sensing. With advances in materials, photonic design architectures, fabrication and integration processes, packaging, and testing and benchmarking, in the next decade we can expect a transition from single- and few-function prototypes to large-scale integration of multi-functional and reconfigurable devices that will have a transformative impact on quantum information science and engineering., JPhys Photonics, 4 (1), ISSN:2515-7647

Energy harvesting from relatively low-temperature heat sources is important in applications where long-term power sources are needed such as deep space radioisotope thermoelectric generators (RTGs). Current solutions exhibit low efficiency, require exotic materials and structures, and direct contact to the heat source. While the infrared rectenna is currently low efficiency, the path exists for high-efficiency solid state devices. We have made a scalable design using standard CMOS processes, allowing for large-area fabrication. This would allow devices to be made on the wafer scale using existing fabrication technology. The rectenna has the advantage of using radiated power, thus it does not require direct contact to the hot source, but instead must only view the source. This will simplify packaging requirements and make a more robust system. The devices are monolithic and thus robust to adverse operating environments. Here we will discuss the rectenna's physics of operation, particularly light coupling into the structure. Incoming light is coupled to a metal-oxide-semiconductor (MOS) tunnel diode via a broad-area nanoantenna. The nanoantenna consists of a subwavelength metal patterning that concentrates the light into the tunnel diode where the optical signal is rectified. Both the nanoantenna and tunnel diode are distributed devices utilizing the entire area of the surface. The nanoantenna also serves as one contact of the tunnel diode. This direct integration of the nanoantenna and diode overcomes the resistive loss limitations found in prior IR rectenna concepts that resembled microwave rectenna designs scaled down to infrared sizes. We will show simulation and experimental results of fabricated devices. Simulations of the optical fields in the tunnel gap are illustrative of device operation and will be discussed. The measured infrared photocurrent is compared to simulated expectations. Far-field radiation power conversion is demonstrated using standard radiometric techniques and correlated with the rectified current response. We discuss thermal modelling of the localized heat generation within the rectenna structure to demonstrate the lack of a thermoelectric response. Lastly, we discuss future directions of work to improve power conversion efficiency.

Just as classical information technology rests on a foundation built of interconnected information-processing systems, quantum information technology (QIT) must do the same. A critical component of such systems is the interconnect, a device or process that allows transfer of information between disparate physical media, for example, semiconductor electronics, individual atoms, light pulses in optical fiber, or microwave fields. While interconnects have been well engineered for decades in the realm of classical information technology, quantum interconnects (QuICs) present special challenges, as they must allow the transfer of fragile quantum states between different physical parts or degrees of freedom of the system. The diversity of QIT platforms (superconducting, atomic, solid-state color center, optical, etc.) that will form a quantum internet poses additional challenges. As quantum systems scale to larger size, the quantum interconnect bottleneck is imminent, and is emerging as a grand challenge for QIT. For these reasons, it is the position of the community represented by participants of the NSF workshop on Quantum Interconnects that accelerating QuIC research is crucial for sustained development of a national quantum science and technology program. Given the diversity of QIT platforms, materials used, applications, and infrastructure required, a convergent research program including partnership between academia, industry and national laboratories is required. This document is a summary from a U.S. National Science Foundation supported workshop held on 31 October - 1 November 2019 in Alexandria, VA. Attendees were charged to identify the scientific and community needs, opportunities, and significant challenges for quantum interconnects over the next 2-5 years., Comment: This is an updated version V2, including expanded text and listing of all co-authors. To whom correspondence should be addressed: Marko Lon\v{c}ar: loncar@seas.harvard.edu; Michael G. Raymer: raymer@uoregon.edu

The elastic moduli of amorphous and crystalline atomic layer-deposited Hf1-xZrxO2 (HZO, x = 0, 0.31, 0.46, 0.79, 1) films prepared with TaN electrodes on silicon substrates were investigated using picosecond acoustic measurements. The moduli of the amorphous films were observed to increase between 211 ± 6 GPa for pure HfO2 and 302 ± 9 GPa for pure ZrO2. In the crystalline films, it was found that the moduli increased upon increasing the zirconium composition from 248 ± 6 GPa for monoclinic HfO2 to 267 ± 9 GPa for tetragonal ZrO2. Positive deviations from this increase were observed for the Hf0.69Zr0.31O2 and Hf0.54Zr0.46O2 compositions, which were measured to have moduli of 264 ± 8 GPa and 274 ± 8 GPa, respectively. These two compositions contained the largest fractions of the ferroelectric orthorhombic phase, as assessed from polarization and diffraction data. The biaxial stress states of the crystalline films were characterized through sin2( ψ) x-ray diffraction analysis. The in-plane stresses were all found to be tensile and observed to increase with the increasing zirconium composition, between 2.54 ± 0.6 GPa for pure HfO2 and 5.22 ± 0.5 GPa for pure ZrO2. The stresses are consistent with large thermal expansion mismatches between the HZO films and silicon substrates. These results demonstrate a device-scale means to quantify biaxial stress for investigation on its effect on the ferroelectric properties of hafnia-based materials.

Fourier modal expansion techniques are very well suited for electromagnetic (EM) scattering in planar periodic stratified media. These techniques expand the transverse EM fields in Bloch modes in each strata unit-cell, but do not rigorously enforce EM boundary conditions at interior material interfaces which gives rise to slow convergence of the polarized S-matrix values with increasing Fourier series truncation order. We present a normal vector (NV) Fourier modal scattering approach that uses the gradient of the real permittivity in the unit-cell to generate a local NV resulting in anisotropic eigenmodes of Maxwell's equations that satisfy interior boundary conditions. The convergence of this expansion method is examine numerically for our analytic NV derived from planar primitive geometry elements for various example structures. The Fourier modal NV method is then derived for the planar cavity boundary value problem and the cavity eigenmodes and density of states is determined from the analytic continuation of the secular determinant. A complete scattering method for highly dispersive materials and sub-wavelength structures has been presented that is adaptable to planar EM cavity problems using fluctuation electrodynamics formalism.

Composition dependence of second harmonic generation, refractive index, extinction coefficient, and optical bandgap in 20 nm thick crystalline Hf1−xZrxO2 (0 ≤ x ≤ 1) thin films is reported. The refractive index exhibits a general increase with increasing ZrO2 content with all values within the range of 1.98–2.14 from 880 nm to 400 nm wavelengths. A composition dependence of the indirect optical bandgap is observed, decreasing from 5.81 eV for HfO2 to 5.17 eV for Hf0.4Zr0.6O2. The bandgap increases for compositions with x > 0.6, reaching 5.31 eV for Hf0.1Zr0.9O2. Second harmonic signals are measured for 880 nm incident light. The magnitude of the second harmonic signal scales with the magnitude of the remanant polarization in the composition series. Film compositions that display near zero remanent polarizations exhibit minimal second harmonic generation while those with maximum remanent polarization also display the largest second harmonic signal. The results are discussed in the context of ferroelectric phase assemblage in the hafnium zirconium oxide films and demonstrate a path toward a silicon-compatible integrated nonlinear optical material.

We demonstrate thinned resonant longwave infrared detectors with quantum efficiencies of over 60% in the longwave infrared. This improvement over unthinned detectors is made possible by a nanoantenna that confines the incident optical energy in a reduced volume compared to traditional detector architectures.

Photonic integrated circuits provide a compact and stable platform for quantum photonics. Here we demonstrate a silicon photonics quantum key distribution (QKD) encoder in the first high-speed polarization-based QKD field tests. The systems reach composable secret key rates of 1.039 Mbps in a local test (on a 103.6-m fiber with a total emulated loss of 9.2 dB) and 157 kbps in an intercity metropolitan test (on a 43-km fiber with 16.4 dB loss). Our results represent the highest secret key generation rate for polarization-based QKD experiments at a standard telecom wavelength and demonstrate photonic integrated circuits as a promising, scalable resource for future formation of metropolitan quantum-secure communications networks.

Electrical power generation from a moderate temperature thermal source by means of direct conversion of infrared radiation is important and highly desirable for energy harvesting from waste heat and micropower applications. Here, we demonstrate direct rectified power generation from an unbiased large-area nanoantenna-coupled tunnel diode rectifier, called a rectenna. Using a vacuum radiometric measurement technique with irradiation from a temperature-stabilized thermal source, a generated power density of 8 nW/cm$^2$ is observed at a source temperature of 450C for the unbiased rectenna across an optimized load resistance. The optimized load resistance for the peak power generation for each temperature coincides with the tunnel diode resistance at zero bias and corresponds to the impedance matching condition for a rectifying antenna. Current voltage measurements of a thermally illuminated large-area rectenna show current zero crossing shifts into the second quadrant indicating rectification. Photon-assisted tunneling in the unbiased rectenna is modeled as the mechanism for the large short-circuit photocurrents observed where the photon energy serves as an effective bias across the tunnel junction. The measured current and voltage across the load resistor as a function of the thermal source temperature represents direct current electrical power generation., 8 pages, 7 figures, Journal submission

Direct rectification of electromagnetic radiation is a well-established method for wireless power conversion in the microwave region of the spectrum, for which conversion efficiencies in excess of 84% have been demonstrated. Scaling to the infrared or optical part of the spectrum requires ultrafast rectification that can only be obtained by direct tunnelling. Many research groups have looked to plasmonics to overcome antenna-scaling limits and to increase the confinement. Recently, surface plasmons on heavily doped Si surfaces were investigated as a way of extending surface-mode confinement to the thermal infrared region. Here we combine a nanostructured metallic surface with a heavily doped Si infrared-reflective ground plane designed to confine infrared radiation in an active electronic direct-conversion device. The interplay of strong infrared photon-phonon coupling and electromagnetic confinement in nanoscale devices is demonstrated to have a large impact on ultrafast electronic tunnelling in metal-oxide-semiconductor (MOS) structures. Infrared dispersion of SiO2 near a longitudinal optical (LO) phonon mode gives large transverse-field confinement in a nanometre-scale oxide-tunnel gap as the wavelength-dependent permittivity changes from 1 to 0, which leads to enhanced electromagnetic fields at material interfaces and a rectified displacement current that provides a direct conversion of infrared radiation into electric current. The spectral and electrical signatures of the nanoantenna-coupled tunnel diodes are examined under broadband blackbody and quantum-cascade laser (QCL) illumination. In the region near the LO phonon resonance, we obtained a measured photoresponsivity of 2.7 mA W(-1) cm(-2) at -0.1 V.

A sensitive optical detector is presented based on a deeply depleted graphene-insulator-semiconducting (D2GIS) junction, which offers the possibility of simultaneously leveraging the advantages of both charge integration and localized amplification. Direct read-out and built-in amplification are accomplished via photogating of a graphene field-effect transistor (GFET) by carriers generated within a deeply depleted low-doped silicon substrate. Analogous to a depleted metal-oxide-semiconducting junction, photo-generated charge collects in the potential well that forms at the semiconductor/insulator interface and induces charges of opposite polarity within the graphene film modifying its conductivity. This device enables simultaneous photo-induced charge integration with continuous “on detector” readout through use of graphene. The resulting devices exhibit responsivities as high as 2,500 A/W (25,000 S/W) for visible wavelengths and a dynamic range of 30 dB. As both the graphene and device principles are transferrable to arbitrary semiconductor absorbers, D2GIS devices offer a high-performance paradigm for imaging across the electromagnetic spectrum.

We experimentally demonstrate ultrahigh extinction ratio (>65 dB) amplitude modulators (AMs) that can be electrically tuned to operate across a broad spectral range of 160 nm from 1480 – 1640 nm and 95 nm from 1280 – 1375 nm. Our on-chip AMs employ one extra coupler compared with conventional Mach-Zehnder interferometers (MZI), thus form a cascaded MZI (CMZI) structure. Either directional or adiabatic couplers are used to compose the CMZI AMs and experimental comparisons are made between these two different structures. We investigate the performance of CMZI AMs under extreme conditions such as using 95:5 split ratio couplers and unbalanced waveguide losses. Electro-optic phase shifters are also integrated in the CMZI AMs for high-speed operation. Finally, we investigate the output optical phase when the amplitude is modulated, which provides us valuable information when both amplitude and phase are to be controlled. Our demonstration not only paves the road to applications such as quantum information processing that requires high extinction ratio AMs but also significantly alleviates the tight fabrication tolerance needed for large-scale integrated photonics.

We examine integration of a patterned metal nanoantenna (or metasurface) directly onto long-wave infrared detectors. These structures show significantly improved external quantum efficiency compared to their traditional counterparts. We will show simulation and experimental results.

We examine the vacuum infrared photoresponse of a large-area nanoantenna-coupled tunnel diode rectenna resulting from thermal radiation from a temperature controlled heater. The measured infrared photocurrent is obtained as a function of the source temperature, sample distance and view factor. Far-field radiation power conversion is examined using standard radiometric techniques and correlated with the rectified current response.

High-quality infrared focal plane arrays (FPAs) are used in many satellite, astronomical, and terrestrial applications. These applications require highly-sensitive, low-noise FPAs, and therefore do not benefit from advances made in low-cost thermal imagers where reducing cost and enabling high-temperature operation drive device development. Infrared detectors used in FPAs have been made for decades from alloys of mercury cadmium telluride (MCT). These infrared detectors are nearing the believed limit of their performance. This limit, known in the infrared detector community as Rule 07, dictates the dark current floor for MCT detectors, in their traditional architecture, for a given temperature and cutoff wavelength. To overcome the bounds imposed by Rule 07, many groups are working on detector compounds other than MCT. We focus on detectors employing III-V-based gallium-free In As Sb superlattice active regions while also changing the basic architecture of the pixel to improve signal-to-noise. Our architecture relies on a resonant, metallic, subwavelength nanoantenna patterned on the absorber surface, in combination with a Fabry-Perot cavity, to couple the incoming radiation into tightly confined modes near the nanoantenna. This confinement of the incident energy in a thin layer allows us to greatly reduce the volume of the absorbing layer to a fraction of the free-space wavelength, yielding a corresponding reduction in dark current from spontaneously generated electron-hole pairs in the absorber material. This architecture is detector material agnostic and could be applied to MCT detector structures as well, although we focus on using superlattice antimonide-based detector materials. This detector concept has been applied to both mid-wave (3–5 μm) and longwave (8–12 μm) infrared detectors and absorbers. Here we examine long-wave devices, as these detectors currently have a larger gap between desired device performance and that of currently existing detectors. The measured structures show an external quantum efficiency exceeding 50%. We present a comparison of the modeled and measured photoresponse of these detectors and compare these detectors to currently available commercial detectors using relevant metrics such as external quantum efficiency. We also discuss modeling of crosstalk between adjacent pixels and its influence on the potential for a dual-wavelength detector. Finally, we evaluate potential advances in these detectors that may occur in the near future.

The goal of this paper is to investigate full-wave simulations of realistic implementations of multifunctional nanoantenna enabled detectors (NEDs). We realize a 2×2 pixelated array structure that supports two wavelengths of operation. After designing each resonating structure independently using full-wave simulations with periodic boundary conditions mimicking the whole infinite array, we construct a supercell made of a 2×2 pixelated array with periodic boundary conditions mimicking the full NED. In the NED, each pixel comprises 10–20 nanoantennas. Our simulations account for the cross-talk between contiguous pixels. We observe that, even though there are finite extent effects, the pixels work as designed, each responding at the respective wavelength of operation. We want to stress that realistic simulations of multifunctional NEDs need to be performed to verify the design functionality by taking into account finite extent and cross-talk effects.

We demonstrate a silicon photonic transceiver circuit to implement polarization encoding/decoding for DV-QKD. The circuit is capable of encoding BB84 states with >30 dB PER and decoding with >20 dB ER.

We experimentally demonstrate amplitude modulators (AMs) with >65 dB extinction across over a 160 nm spectral range. The output optical phase response is also characterized when the amplitude is modulated.

The transfer Hamiltonian tunneling current is derived in a time-dependent density matrix formulation and is used to examine photon-assisted tunneling. Bardeen's tunneling expression arises as the result of first order perturbation theory in a mean-field expansion of the density matrix. Photon-assisted tunneling from confined electromagnetic fields in the forbidden barrier region occurs due to time-varying polarization and wavefunction overlap in the gap, which leads to a non-zero tunneling current in asymmetric device structures, even in an unbiased state. The photon energy is seen to act as an effective temperature dependent bias in a uniform barrier asymmetric tunneling example problem. Higher order terms in the density matrix expansion give rise to multi-photon enhanced tunneling currents that can be considered an extension of non-linear optics where the non-linear conductance plays a similar role as the non-linear susceptibilities in the continuity equations., Comment: 8 pages, 2 figures

Sandia National Laboratories has developed a toolkit of RF photonic devices. These devices have been used in the development of multielement RF photonic circuits and in support of MPW runs. In this talk I will discuss Sandia's silicon photonic process and RF photonic device performance.

We present experimental results for a selective epitaxially grown Ge-on-Si separate absorption and charge multiplication (SACM) integrated waveguide coupled avalanche photodiode (APD) compatible with our silicon photonics platform. Epitaxially grown Ge-on-Si waveguide-coupled linear mode avalanche photodiodes with varying lateral multiplication regions and different charge implant dimensions are fabricated and their illuminated device characteristics and high-speed performance is measured. We report a record gain-bandwidth product of 432 GHz for our highest performing waveguide-coupled avalanche photodiode operating at 1510nm. Bit error rate measurements show operation with BER< 10-12, in the range from -18.3 dBm to -12 dBm received optical power into a 50 Ω load and open eye diagrams with 13 Gbps pseudo-random data at 1550 nm.

The emergence of coherent quantum feedback control (CQFC) as a new paradigm for precise manipulation of dynamics of complex quantum systems has led to the development of efficient theoretical modeling and simulation tools and opened avenues for new practical implementations. This work explores the applicability of the integrated silicon photonics platform for implementing scalable CQFC networks. If proven successful, on-chip implementations of these networks would provide scalable and efficient nanophotonic components for autonomous quantum information processing devices and ultra-low-power optical processing systems at telecommunications wavelengths. We analyze the strengths of the silicon photonics platform for CQFC applications and identify the key challenges to both the theoretical formalism and experimental implementations. In particular, we determine specific extensions to the theoretical CQFC framework (which was originally developed with bulk-optics implementations in mind), required to make it fully applicable to modeling of linear and nonlinear integrated optics networks. We also report the results of a preliminary experiment that studied the performance of an in situ controllable silicon nanophotonic network of two coupled cavities and analyze the properties of this device using the CQFC formalism., 13 pages, 4 figures. Comments welcome

Si-Ge lateral avalanche photodiodes (Si-Ge LAPDs) are promising devices for single photon detection, but they also have technology challenges. Si-Ge LAPDs are CMOS compatible and capable of detecting photons near the 1550 nm telecommunications bands. However, the Si-Ge LAPD exhibits a unique avalanche multiplication process in silicon, where the electrons and holes follow curved paths in three-dimensional space. Traditional models for the analysis of the avalanche multiplication process assume one-dimensional paths for the carriers that undergo the chains of impact ionizations; therefore, they are not suitable for analyzing the avalanche properties of Si-Ge LAPDs. In this paper, the statistics of the avalanche process in the Si-Ge LAPD are modeled analytically using a method that was recently developed by our group for understanding the avalanche multiplication in nanopillar, core-shell GaAs avalanche photodiodes, for which the electric field is non-uniform in magnitude and direction. Specifically, the calculated mean avalanche gain and the excess noise are presented for the Si-Ge LAPD device. It is also shown that the avalanche characteristics depend upon the specific avalanche path taken by the carrier, which depends, in turn, on the lateral location where each photon is absorbed in the Ge absorber. This property can be exploited to achieve reduced excess noise as well as wavelength-sensitive single-photon detection.

We present experimental results for a Ge on Si separate absorption and charge multiplication (SACM) integrated waveguide coupled avalanche photodiode (APD) compatible with our silicon photonics platform. Our linear mode APD has a gain-bandwidth product in excess of 200 GHz. Furthermore, we demonstrate error free operation (BER< 10−12) with our waveguide coupled linear mode APD using pseudo-random bit sequence (PBRS) data at 10 Gb/s.

We demonstrate an on-chip polarization beam splitter (PBS), which is adiabatic for the transverse magnetic mode, and diabatic for the transverse electric mode. The PBS has a simple structure that is tolerant to manufacturing variations and exhibits high polarization extinction ratios over a wide bandwidth.

Conversion of plane waves to surface waves prior to detection allows key advantages in changes to the architecture of the detector pixels in a focal plane array. We have integrated subwavelength patterned metal nanoantennas with various detector materials to incorporate these advantages: midwave infrared indium gallium arsenide antimonide detectors and longwave infrared graphene detectors. Nanoantennas offer a means to make infrared detectors much thinner by converting incoming plane waves to more tightly bound and concentrated surface waves. Thinner architectures reduce both dark current and crosstalk for improved performance. For graphene detectors, which are only one or two atomic layers thick, such field concentration is a necessity for usable device performance, as single pass plane wave absorption is insufficient. Using III-V detector material, we reduced thickness by over an order of magnitude compared to traditional devices. We will discuss Sandia’s motivation for these devices, which go beyond simple improvement in traditional performance metrics. The simulation methodology and design rules will be discussed in detail. We will also offer an overview of the fabrication processes required to make these subwavelength structures on at times complex underlying devices based on III-V detector material or graphene on silicon or silicon carbide. Finally, we will present our latest infrared detector characterization results for both III-V and graphene structures.

We review Sandia's silicon photonics platform for national security applications. Silicon photonics offers the potential for extensive size, weight, power, and cost (SWaP-c) reductions compared to existing III–V or purely electronics circuits. Unlike most silicon photonics foundries in the US and internationally, our silicon photonics is manufactured in a trusted environment at our Microsystems and Engineering Sciences Application (MESA) facility. The Sandia fabrication facility is certified as a trusted foundry and can therefore produce devices and circuits intended for military applications. We will describe a variety of silicon photonics devices and subsystems, including both monolithic and heterogeneous integration of silicon photonics with electronics, that can enable future complex functionality in aerospace systems, principally focusing on communications technology in optical interconnects and optical networking.

We examine gated-Geiger mode operation of an integrated waveguide-coupled Ge-on-Si lateral avalanche photodiode (APD) and demonstrate single photon detection at low dark count for this mode of operation. Our integrated waveguide-coupled APD is fabricated using a selective epitaxial Ge-on-Si growth process resulting in a separate absorption and charge multiplication (SACM) design compatible with our silicon photonics platform. Single photon detection efficiency and dark count rate is measured as a function of temperature in order to understand and optimize performance characteristics in this device. We report single photon detection of 5.27% at 1310 nm and a dark count rate of 534 kHz at 80 K for a Ge-on-Si single photon avalanche diode. Dark count rate is the lowest for a Ge-on-Si single photon detector in this range of temperatures while maintaining competitive detection efficiency. A jitter of 105 ps was measured for this device.

We have examined graphene absorption in a range of graphene-based infrared devices that combine either monolayer or bilayer graphene with three different gate dielectrics. Electromagnetic simulations show that the optical absorption in graphene in these devices, an important factor in a functional graphene-based detector, is strongly dielectric-dependent. These simulations reveal that plasmonic excitation in graphene can significantly influence the percentage of light absorbed in the entire device, as well as the graphene layer itself, with graphene absorption exceeding 25% in regions where plasmonic excitation occurs. Notably, the dielectric environment of graphene has a dramatic influence on the strength and wavelength range over which the plasmons can be excited, making dielectric choice paramount to final detector tunability and sensitivity.

We demonstrate a silicon photonic transceiver circuit for high-speed discrete variable quantum key distribution that employs a common structure for transmit and receive functions. The device is intended for use in polarization-based quantum cryptographic protocols, such as BB84. Our characterization indicates that the circuit can generate the four BB84 states (TE/TM/45°/135° linear polarizations) with >30 dB polarization extinction ratios and gigabit per second modulation speed, and is capable of decoding any polarization bases differing by 90° with high extinction ratios.

Three-dimensional (3D) metafilms composed of periodic arrays of silicon unit cells containing single and multiple micrometer-scale vertical split ring resonators (SRRs) per unit cell were fabricated. In contrast to planar and stacked planar structures, these 3D metafilms have a thickness t ∼ λd/4, allowing for classical thin film effects in the long wavelength limit. The infrared specular far-field scattering response was measured for metafilms containing one and two resonators per unit cell and compared to numerical simulations. Excellent agreement in the frequency region below the onset of diffractive scattering was obtained. For dense arrays of unit cells containing single SRRs, normally incident linearly polarized plane waves which do not excite a resonant response result in thin film interference fringes in the reflected spectra and are virtually indistinguishable from the scattering response of an undecorated array of unit cells. For the resonant linear polarization, the specular reflection for arra...

We examine the modal structure and dispersion of periodically nanostructured planar metallic cavities within the scattering matrix formulation. By nanostructuring a metallic grating in a planar cavity, artificial surface excitations or spoof plasmon modes are induced with dispersion determined by the periodicity and geometric characteristics of the grating. These spoof surface plasmon modes are shown to give rise to new cavity polaritonic modes at short mirror separations that modify the density of modes in nanostructured cavities. The increased modal density of states form cavity polarirons have a large impact on the fluctuation induced electromagnetic forces and enhanced hear transfer at short separations.

We examined the spectral responsivity of a 1.77 μm thick type-II superlattice based long-wave infrared detector in combination with metallic nanoantennas. Coupling between the Fabry-Perot cavity formed by the semiconductor layer and the resonant nanoantennas on its surface enables spectral selectivity, while also increasing peak quantum efficiency to over 50%. Electromagnetic simulations reveal that this high responsivity is a direct result of field-enhancement in the absorber layer, enabling significant absorption in spite of the absorber's subwavelength thickness. Notably, thinning of the absorbing material could ultimately yield lower photodetector noise through a reduction in dark current while improving photocarrier collection efficiency. The temperature- and incident-angle-independent spectral response observed in these devices allows for operation over a wide range of temperatures and optical systems. This detector paradigm demonstrates potential benefits to device performance with applications throughout the infrared.

Organic materials that have desirable luminescence properties, such as a favorable emission spectrum and high luminescence efficiency, are not necessarily suitable for single layer organic light-emitting diodes (LEDs) because the material may have unequal carrier mobilities or contact limited injection properties. As a result, single layer LEDs made from such organic materials are inefficient. In this article, we present device model calculations of single layer and bilayer organic LED characteristics that demonstrate the improvements in device performance that can occur in bilayer devices. We first consider an organic material where the mobilities of the electrons and holes are significantly different. The role of the bilayer structure in this case is to move the recombination away from the electrode that injects the low mobility carrier. We then consider an organic material with equal electron and hole mobilities but where it is not possible to make a good contact for one carrier type, say electrons. Th...

We present calculations of single layer organic light emitting diode (LED) characteristics using a device model which includes charge injection, transport, recombination, and space charge effects in the organic material. Contact limited and ohmic contacts, high and low carrier mobilities, and device thicknesses from 5 to 200 nm are considered. The scaling of device current with applied voltage bias and organic film thickness is described for contact limited and ohmic contacts. Calculated device current, light output, and quantum and power efficiency are presented for representative cases of material and device parameters. These results are interpreted using the calculated spatial variation of the electric field, charge density, and recombination rate density in the devices. We find that efficient single layer organic LEDs are possible for a wide range of organic material and contact parameters.