Search

In this paper, many impedance-source inverters with coupled inductors have been investigated to obtain a high step-up boost ratio. However, the leakage inductors in these topologies induce great voltage spikes at the dc link, which will increase the voltage stress of switches. Thus, the power level of inverters is limited. Furthermore, the efficiency of the inverters can be degraded by the losses associated with leakage inductors. To address abovementioned issues, this paper proposes a family of low-spike high-efficiency Y-source inverters. The proposed inverters have the ability of eliminating voltage spikes at the dc link and recycling the leakage energy via the additional diode and capacitor. In order to show the excellent characteristics of the proposed topologies, this paper compares the performances of the proposed inverters and the improved-Y-source inverter in many aspects. Simulation and experimental results have verified the abilities of the proposed inverters. [ABSTRACT FROM AUTHOR]

A space vector modulation (SVM) technique of a dual-inverter system for an open-end winding motor drive is described in this paper, where one inverter has a battery power source and the other has an only capacitor across the dc bus. The SVM must be achieved to operate the motor with field-oriented control and simultaneously to control the capacitor voltage at a constant value by using redundant switching states of the dual-inverter system. The control of the capacitor voltage is carried out by selecting a charging or a discharging mode in each redundant switching state, taking the instantaneous motor power factor into account. In addition, it is also required to reduce the error voltage pulses, which are generated in output multilevel voltage waveforms during the dead time. The compensation method of the existing dead-time scheme and the improved SVM sequence to reduce the error voltage vectors are proposed in this paper. The proposed methods are examined through several experimental tests and are confirmed to generate superior output voltage waveforms from the viewpoint of the measured total harmonic distortion and dv/dt. [ABSTRACT FROM AUTHOR]

In this paper, two structures are proposed for the switched-inductor quasi-Z-source inverter. In the proposed structures to extend the voltage gain of inverter, two new switched-inductor structures are used. In the proposed structures, voltage across the capacitors in the Z-source network and in the switched-inductor is symmetric and small. The other advantage of proposed inverters is known as achieving higher voltage gain per smaller duty cycle ratio (of shoot-through). Compared with a conventional continuous input current switched-inductor quasi-Z-source inverter at the same gain voltage, there is less of a ripple of input current in the proposed inverters. In this paper, at first the both the conventional and the proposed switched-inductor Z-source inventers are thoroughly investigated to find out their governing relations. Then, the proposed Z-source inverters are compared with the conventional ones by simulating them to assess their performance efficiency. Next, applying the simple boost pulse width modulation the simulation is carried out with PSCAD/EMTDC software. After that, to evaluate the obtained results, the prototypes of the proposed inverters with 48 Vdc input voltage are used. [ABSTRACT FROM PUBLISHER]

In this paper, new half-bridge and full-bridge topologies for a switched-boost inverter are proposed. These topologies have a high boost factor in comparison with conventional types. In addition, the proposed topologies have continuous input current and can generate zero-voltage level in output. In this paper, the operation of the proposed inverters in different operating modes is analyzed. Then, the values of inductors and capacitors are designed. Moreover, the used switching pattern and its logical diagram are introduced. A comprehensive comparison between the proposed and conventional topologies in terms of the boost factor, the number of elements, and the efficiency shows the good features of the proposed inverters. Finally, to verify correct operation of the proposed topologies and derived equations, simulation and experimental results are presented. [ABSTRACT FROM AUTHOR]

For power converters with inductive loads, a freewheeling path is needed for the current due to reactive power. The MOSFET synchronous rectification (SR) is widely used to reduce the conduction loss during the freewheeling period. Due to the wide band gap of silicon carbide (SiC), the intrinsic body diode of SiC MOSFET exhibits a high voltage drop. Hence, an antiparallel SiC Schottky diode is normally implemented to eliminate its conduction. However, the external SiC Schottky diode is not fully utilized as it only works during the dead time. In this paper, the hard-switching SR is investigated in an SiC three-phase inverter and compared with a conventional inverter using freewheeling diode (FWD). An improved power loss model for the two inverters has been developed. It is found that the inverter using SR has higher efficiency due to the smaller switching loss. A 7-kW prototype of SiC three-phase inverter is built, which achieves a peak efficiency of 98.8% ($\pm$ 0.15%) and 98.5% ($\pm$ 0.15%) at 40 kHz using SR and FWD, respectively. This paper confirms that the SiC MOSFET is an ideal candidate for the SR. [ABSTRACT FROM PUBLISHER]

In this paper, two topologies are presented for the enhanced-boost quasi-Z-source inverters (qZSI), namely continuous input current configuration and discontinuous input current configuration of enhanced-boost qZSI with two-switched impedance networks. Similar to enhanced-boost impedance-source inverters (ZSIs), these proposed inverter topologies possess very high boost voltage inversion at low shoot-through duty ratio and high modulation index to provide an improved quality output voltage. Compared to enhanced-boost ZSIs with two-switched Z-source impedance networks, these proposed inverter topologies share common ground with source and bridge inverter, overcome the starting inrush problem, and draw continuous input current and the lower voltage across the capacitors. Moreover, the input ripple current is negligible. This paper presents the operating principles and analysis of continuous input current configuration enhanced-boost qZSI with two-switched impedance networks and compares with ZSI, switched inductor ZSI, DA/CA-qZSI, and enhanced-boost ZSIs. The theoretical analysis is done and is validated through simulation and experimental results. [ABSTRACT FROM PUBLISHER]

This paper presents an improved rotating restart method for a sensorless permanent magnet synchronous motor (PMSM) drive system using repetitive zero voltage vectors. To restart the sensorless PMSM drive system, a method for estimating initial rotor position and speed is required due to the absence of sensors such as encoders and resolvers. The rotor position and speed can be estimated using the short-circuit current vectors generated by applying zero voltage vectors. However, the estimated rotor position and speed can be inaccurate. The inaccurate rotor position that causes the current is distorted by the back-electromotive force of the PMSM, and it is impossible to precisely control the system. Therefore, an improved rotating restart method for the sensorless PMSM drive system using repetitive zero voltage vectors is proposed. The effectiveness of the proposed method is verified through simulation and experimental results using a 5-kW PMSM drive system. [ABSTRACT FROM AUTHOR]

The conventional three-level inverter only has voltage buck capability. The quasi-Z-source three-level T-type inverter (QZS 3LT $^2$ I) has been proposed to realize voltage buck–boost operation. In this paper, we further propose a novel modulation scheme for the QZS 3LT $^2$ I to realize voltage boosting, reduce the common-mode voltage (CMV), and control the neutral-point voltage balance simultaneously. The proposed scheme adopts a large vector, a medium vector, a small vector with low CMV magnitude, a zero vector, and a shoot-through vector to generate the output voltage. According to sector number and neutral-point voltage difference, a p-type or n-type small vector with low CMV magnitude is properly selected to balance the neutral-point voltage. Shoot-through states are inserted within zero vector to boost the dc input voltage without affecting the ac output voltage. Dwell times of basic vectors are calculated through the revised volt–second balance equation. Furthermore, a coordinate control strategy between neutral-point voltage balance and voltage boosting is proposed. Doing so, the CMV magnitude can be restricted within one-sixth of dc-link voltage and neutral-point voltage imbalance can be effectively mitigated. The effectiveness of the proposed scheme is verified by simulations and experiments. [ABSTRACT FROM AUTHOR]

A multilevel dodecagonal voltage space vector generation scheme for variable-speed drive applications with single-dc-link operation requires a large value of capacitance for cascaded H-bridge (CHB) filters, when operated at lower speeds. In existing schemes, the multilevel dodecagonal structure is obtained by cascading a flying capacitor inverter with a CHB. In this paper, a new scheme has been proposed to minimize the capacitance requirement for full speed operation by creating vector redundancies using modular and equal voltage CHBs. Also, an algorithm has been developed to optimize the selection of vector redundancies among the CHBs in order to minimize the voltage ripple of the floating capacitors. The proposed algorithm considers instantaneous capacitor voltages and phase currents for optimal selection of vector redundancies. A mathematical model for capacitor voltage deviation is presented, and the effectiveness of the proposed algorithm is verified in both the simulation and the experiment. [ABSTRACT FROM AUTHOR]

This paper deals with the analysis of the input dc-link voltage ripple in multilevel inverter based on H-bridge and level doubling network (LDN). The LDN is basically a half-bridge fed by a floating capacitor, with voltage self-balancing capability, recalling the concept of a flying capacitor configuration. The amplitude of the LDN voltage ripple is analytically determined considering both the low-order and the switching harmonic components. In particular, peak-to-peak distributions of voltage ripples over the fundamental period are analytically determined, making possible the design of dc-link capacitor relying only on the dc-voltage ripple requirements. The case study makes reference to negligible switching ripple in the output current. It well represents either grid connection or passive load having almost sinusoidal currents. Numerical simulations carried out by MATLAB/Simulink and a complete set of experimental verifications are given to confirm the theoretical developments. [ABSTRACT FROM AUTHOR]

This paper presents a model predictive control technique applied to a dual-active bridge inverter where one of the bridges is floating. The proposed floating bridge topology eliminates the need for isolation transformer in a dual inverter system and therefore reduces the size, weight, and losses in the system. To achieve multilevel output voltage waveforms, the floating inverter dc-link capacitor is charged to the half of the main dc-link voltage. A finite-set model predictive control technique is used to control the load current of the converter as well as the floating capacitor voltage. Model predictive control does not require any switching sequence design or complex switching time calculations as used for space vector modulation; thus, the technique has some advantages in this application. A detailed analysis of the converter as well as the predictive control strategy is given in this paper. Simulation and experimental results to validate the approach are also presented. [ABSTRACT FROM PUBLISHER]

Two three-level inverters driving an open-end winding induction motor can generate equivalent voltage waveforms as a single five-level inverter-based drive. In addition, it can bring in benefits such as reduced dc-link voltage, less number of devices, and fault-tolerant capability, which is favored in high-power motor drive applications. The main challenge with this type of configuration is the appearance of large zero-sequence current circulating between the two inverters, which generates extra losses in the switching devices and the motor as well as affects the normal operation of the machine. Another challenge is to balance the dc-link neutral point voltage of the two three-level inverters. This paper has proposed a simplified decoupled space-vector pulsewidth-modulation (PWM) strategy to eliminate the averaged zero-sequence voltage in each switching cycle by the placement of redundant vectors of each individual inverter using a time shift. Neutral point voltage balance is further achieved by adjusting the time duration of the redundant vectors. In this paper, it is shown that it is possible to operate this kind of drive configuration with a single dc power supply and achieve averaged zero-sequence voltage elimination and neutral-point voltage balancing at the same time. Experimental results of a 5.5-kW dual three-level inverter drive using the proposed PWM strategy are presented, which validates the control method and drive configuration. [ABSTRACT FROM PUBLISHER]

This paper presents a new reconfiguration module for asymmetrical multilevel inverters in which the capacitors are used as the dc links to create the levels for staircase waveforms. This configuration of the multilevel converter makes a reduction in dc sources. On the other hand, it is possible to generate 13 levels with lower dc sources. The proposed module of the multilevel inverter generates 13 levels with two unequal dc sources (2VDC and 1VDC). It also involves two chargeable capacitors and 14 semiconductor switches. The capacitors are self-charging without any extra circuit. The lower number of components makes it desirable to be used in wide range of applications. The module is schematized as two back-to-back T-type inverters and some other switches around it. Also, it can be connected as a cascade modular which leads to a modular topology with more voltage levels at higher voltages. The proposed module makes the inherent creation of the negative voltage levels without any additional circuit (such as H-bridge circuit). Nearest level control switching modulation scheme is applied to achieve high-quality sinusoidal output voltage. Simulations are executed in MATLAB/Simulink and a prototype is implemented in the power electronics laboratory in which the simulation and experimental results show a good performance. [ABSTRACT FROM AUTHOR]

To reduce the common-mode voltage (CMV) and eliminate the CMV spikes for two-level voltage source inverters (2L-VSIs), an improved model predictive control (MPC) based CMV reduction method is proposed in this paper considering dead-time effects. First, an improved voltage vector (VV) preselection strategy is proposed to reduce the CMV spikes caused by the dead time. Second, a new hybrid VV preselection strategy based on a delay compensation strategy and a modified current sector division strategy is proposed to completely eliminate the CMV spikes. As the proposed hybrid VV preselection based MPC strategy makes full use of the six nonzero VVs of the 2L-VSI, the current total harmonic distortions and ripples are reduced. The simulation and experiments are carried out to verify the effectiveness of the proposed strategy. [ABSTRACT FROM AUTHOR]

In this paper, performances on two kinds of aggregated flyback microinverters are compared in aspect of harmonic resonances, which are controlled by current feedback control and peak current control. Based on the Norton models of flyback microinverters obtained by a small-signal modeling approach, potential harmonic resonances with the grid are analyzed. Following that, an impedance-based stability criterion is proposed, where the resonance frequency can be calculated and predicted based on the derived Norton models and the system admittance matrix of aggregated microinverters. After comprehensive analysis and comparisons, it is found that the peak-current-control-based flyback microinverters has better performance on damping the harmonic resonances than the current feedback controlled one. Simulations and experiments are carried out for verifying the effectiveness of the presented models and the correctness of the analysis results. [ABSTRACT FROM AUTHOR]

This paper proposes a transformerless line-interactive uninterruptible power supply (UPS) with low ground leakage current. A high-efficiency bidirectional inverter is suggested, which performs the line-interactive UPS functions with low ground leakage current. It has a full-bridge inverter and a bidirectional switch, which operate with the unipolar pulsewidth modulation. Because the bidirectional switch operates at the line-frequency, switching losses can be lower than the previous transformerless inverters. As the inverter operates, the parasitic capacitance between the inverter and the ac voltage ground is clamped to zero voltage for a positive line cycle and to the ac voltage for a negative line cycle, respectively. Thus, the parasitic capacitance can be prevented from being charged or discharged, which ensures the absence of the ground leakage current. The operation modes of the proposed system are described. The control schemes are presented to design the proposed inverter for the line-interactive UPS. Experimental results for a 2.0 kW prototype are discussed to verify the performance of the proposed system. [ABSTRACT FROM AUTHOR]

This paper characterizes the sampling effect in digital sinusoidal pulse width modulation (SPWM) of voltage source inverter (VSI). The time-domain analysis presented in this paper establishes the relation between the fundamental frequency, carrier frequency, and the sampling frequency at different modulation indices of the SPWM. The analysis investigates the effect of sampling frequency of the digital controller on the output of the VSI. It is shown that the low-frequency harmonic components appear in the frequency spectrum of the VSI output voltage due to sampling. As a result, the output current of digitally controlled VSI is stepped in nature. The double Fourier integral solution of the switched waveform for inner and outer integral limits has been used to derive the expression. The integral solution is obtained using Jacobi-Anger expansions. The generalized results developed in this paper are useful to investigate the sampling effect in high switching frequency DSPWM. The proposed sampling effect has been analyzed for SPWM of single-phase H-bridge inverter. The analytical results are verified using simulation and experimental results. The experimental results have been obtained with the use of field-programmable gate array (FPGA) as a digital controller. [ABSTRACT FROM PUBLISHER]

A new pulsewidth modulation (PWM) strategy which is an alternative approach of the discontinuous PWM (DPWM) for a three-level neutral-point-clamped (NPC) inverter is proposed in this paper. A three-level NPC inverter is completely mature and very well-established topology in high-power applications. However, the three-level NPC inverter has an inheritance problem of the neutral-point voltage unbalancing due to the split dc-link capacitors. This structure can cause large neutral-point voltage ripple. Furthermore, output currents of the three-level NPC inverter are distorted by the neutral-point voltage ripple. Therefore, the neutral-point voltage must be controlled. In this paper, a new DPWM method using two different offsets for the neutral-point ripple reduction is proposed and the effectiveness of the proposed DPWM method is verified by using the simulation and the experimental results. [ABSTRACT FROM PUBLISHER]

The traditional space-vector pulsewidth modulation (SVPWM) maximum voltage transfer ratio (VTR, i.e., the ratio of the output voltage fundamental amplitude to the input voltage fundamental amplitude) is 0.866 in a linear modulation region. In this paper, the output voltage fundamental amplitude and total harmonic distortion (THD) affected by a basic vector and a hexagon vector in traditional indirect SVPWM overmodulation are analyzed. The traditional indirect SVPWM overmodulation usually focuses on the inverter stage to improve the VTR, and there are few methods considering both of the inverter and rectifier stages to improve the overmodulation performance of a matrix converter (MC), including output voltage error, and output and input current THDs. In this paper, a new overmodulation method based on indirect SVPWM is presented. Both the output performance and input performance of the MC with the proposed and traditional overmodulation methods are emulated and tested. Simulation results indicate that the output voltage error and the input current THD are smaller and lower, respectively, with the proposed method. Experimental results verify that theoretical analysis is right, and the proposed overmodulation method is feasible. [ABSTRACT FROM PUBLISHER]

A four-level five-phase open-end winding (OeW) drive topology is introduced in this paper. The drive comprises a five-phase induction machine with open-end stator windings, supplied using two two-level voltage-source inverters with isolated and unequal dc-link voltages, in the ratio 2 : 1. The topology offers the advantages of a modular structure with fewer semiconductor components and has a greater potential for fault tolerance, as compared with an equivalent single-sided four-level drive. Due to the large number of switching states, development of a suitable space vector pulsewidth-modulation (PWM) method can be challenging. Hence, this paper examines the implementation of two-level-shifted carrier-based PWM methods. The effect of dead time on the drive performance is discussed, and it is shown that simultaneous PWM switching of both inverters can lead to degraded output phase voltage waveforms. Detailed analysis of this phenomenon is presented, a solution is proposed, and the modified modulation techniques are incorporated in an experimental setup, at first in conjunction with $V/f$ control. Once the proof of concept has been provided, full field-oriented control is implemented in this OeW drive topology for the first time; detailed experimental testing is conducted, and results are reported. [ABSTRACT FROM AUTHOR]

In this paper, the conventional I- and T-type three-level neutral-point-clamped (3L-NPC) inverter for low-voltage renewable energy systems is first investigated. Literature research shows that the T-type inverter improves I-type's insulated-gate bipolar transistor (IGBT) $+$ IGBT current paths. However, the IGBT $+$ diode paths are the same. The calculation in this paper further reveals that the IGBT $+$ diode current paths dominate the conduction losses and even the whole semiconductor losses. Based on the aforementioned recognitions, a novel T-type inverter is presented as an alternative to be applied in the low-voltage renewable energy systems. In the proposed 3L-NPC, four CoolMosfets replace the IGBT $+$ diode middle bidirectional switch. In the proposed topology, there is no diode involved in the current path supposing the unity power factor. In this way, the conduction loss is expected to be reduced compared with that from the conventional T-type 3L-NPC, particularly in the low and medium power ranges. [ABSTRACT FROM PUBLISHER]

In this paper, the remedial operation of switch faults will be investigated comprehensively for T-type-three-level-inverter-fed dual three-phase motor drives. The open-circuit switch faults in multiple phase legs are discussed at first. The faulty conditions are classified into five categories. Different remedial strategies, namely Type-I to Type-V schemes, are proposed for different faulty conditions. In particular, three kinds of Type-III fault-tolerant control schemes are proposed by using medium-voltage vectors to synthesize small-voltage vectors, in such a way that the mid-point voltage in a dc link can be stabilized well. Then, the short-circuit faults in both clamping switches and half-bridge switches are investigated. By analysis, their operation conditions are equivalent to conditions loss of both P and N voltage levels and open-phase faults, respectively. Thus, the corresponding remedial strategies can be applied accordingly. Particularly, a voltage compensation control method is proposed for conditions, where open-switch faults coexist with open-phase operation induced by short-circuit faults in half-bridge switches. The validity of all of theoretical analysis and the proposed remedial strategies has been verified by experiments. [ABSTRACT FROM PUBLISHER]

In trasformerless grid-connected photovoltaic (PV) systems, common-mode voltage (CMV) fluctuations cause leakage current flow through the stray capacitance of the PV panels. Shoot-through states in a quasi-Z-source inverter (q-ZSI) increase the amplitude of high-order harmonics of CMV. In this paper, by using the modulation technique based on odd pulse width modulation and minor change in the Z network of the three-phase q-ZSI, the leakage current is blocked. No extra semiconductor element is added. By the proposed technique, CMV is kept nearly constant during switching cycles. The experimental results for CMV analysis in a \text1\;\textkW prototype are presented to verify the theoretical analysis. [ABSTRACT FROM PUBLISHER]

Multilevel inverters (MLIs) have replaced conventional two-level inverters for medium-voltage high-power industrial applications. One of the best modulation techniques for MLIs is the space vector modulation (SVM). Although SVM has its own advantages, it has been overlooked for much simpler carrier-based modulation schemes in the industry. Nearest level modulation (NLM) is a simple alternative, which is functionally similar to SVM. In this paper, a new generalized SVM algorithm is presented, in which the SVM is achieved using the concept of NLM. A generalized switch matrix is introduced to derive gate pulses for the inverter, which further simplifies the algorithm. The algorithm is tested and verified for a three-phase, three-level, and five-level neutral-point-clamped inverters in both simulation and hardware. [ABSTRACT FROM PUBLISHER]

This paper presents an optimized topology of 3-$\phi$ , multilevel inverter (MLI) configuration for five or higher level operation with reduced switch count. The proposed solution consists of two basic units (BUs) of multilevel converter and a T-structured 3-level inverter (3-LI). Both BUs are equally shared by the three phases maintaining symmetry among the phases. Moreover, for a higher level operation of the proposed MLI, the modifications required are at two BUs only and not at three legs of the inverter. It further helps in reducing the requirement of extra components for higher level operation compared to the conventional solutions. Furthermore, the topology also has the benefits of reduced switching and conduction loss. An algorithm is also devised to generate the switching pulses for the BUs and the 3-LI, using a carrier-based space vector modulation technique. Presented topology is compared with other existing topologies to prove its advantage. All the details regarding the operating modes and pulse width modulation techniques employed for the proposed system are given and supported by the simulation and experimental results. [ABSTRACT FROM AUTHOR]

Adding the auxiliary switches to the conventional H-bridge inverter is an effective way to eliminate the leakage current for transformerless PV systems, such as H5, H6, etc. Inspired by the newly developed embedded-switch H6 topology, a novel embedded-switch inverter (ESI) is proposed in this paper for three-phase transformerless PV systems. First, the operation principle and characteristics of the proposed ESI are analyzed. Second, the common-mode model of the three-phase ESI is established, based on which the main factors that affect the leakage current are discussed. The finding reveals that the switching states with conventional modulation strategy result in high-frequency common-mode voltage, which is the source of leakage current. In order to solve the problem, a new modulation strategy is presented for ESI to eliminate the high-frequency leakage current. Finally, the time-domain simulation and the experimental tests are carried out. The results verify the effectiveness of the proposed solution. [ABSTRACT FROM AUTHOR]

In this paper, dual-buck structured single-stage buck–boost inverters that use power MOSFETs to achieve high efficiency are presented. The proposed inverters require fewer switches, and half of the switches have reduced current stresses. They have no shoot-through problem; therefore, high system reliability can be obtained. The dead-time in PWM signals can be minimized or eliminated, which improving the quality of the output ac voltages and increasing the efficiency. In the proposed inverters, MOSFETs can be used without reverse-recovery issues of their body diodes to boost the efficiency and increase the switching frequency. To further improve the efficiency and stability of the proposed single-phase inverter, PWM strategies combining high- and low-frequency modulation are presented. A hardware prototype of the single-phase inverter was built and tested using resistive, inductive, and nonlinear loads. Experimental results for a 300-W prototype inverter show a 97.4% peak efficiency with a 25 kHz switching frequency. [ABSTRACT FROM AUTHOR]

The parallel three-phase grid-connected converters sharing dc and ac bus can increase the system power level effectively. However, the zero sequence circulating current (ZSCC) will occur inevitably under space vector pulse width modulation or discontinuous pulse width modulation (DPWM). In this paper, the mechanism and the mathematical model of ZSCC are studied. Then, a hybrid PWM (HPWM) strategy is proposed to suppress the ZSCC based on the same zero sequence voltage injected, which is dependent on the common grid information. The dc voltage utilization of HPWM can be extended compared with sinusoidal PWM (SPWM). The number of parallel modules can be infinity theoretically by using HPWM. It is noted that there is no internal commutation among modules (expect the dq current reference). Finally, the feasibility and the effectiveness of the proposed method are verified by experiments. [ABSTRACT FROM AUTHOR]

The battery energy-stored quasi-Z-source (BES-qZS)-based photovoltaic (PV) power generation system combines advantages of the qZS inverter and the battery energy storage system. However, the second-harmonic ( \text2\omega ) power ripple degrades the system's performance and affects the system's design. An accurate model to analyze the \text2\omega ripple is very important. The existing models did not consider the battery, or assumed a symmetric qZS network with $L_{{1}}= L_{{2}}$ and $C_{{1}}= C_{{2}}$, which limits the design freedom and causes oversized impedance parameters. This paper proposes a comprehensive model for the single-phase BES-qZS-PV inverter system, where the battery is considered and there is no restriction of $L_{{1}}= L_{{2}}$ and $C_{{1}}= C_{{2}}$ . Based on the built model, a BES-qZS impedance design method is proposed to mitigate the \text2\omega ripple with asymmetric qZS network. Simulation and experimental results verify the proposed \text2\omega ripple model and impedance design method. [ABSTRACT FROM AUTHOR]

Traditional model predictive control cost functions, when utilizing long prediction horizons ( $N\geq 10$) in power inverter applications, have demonstrated harmonic performances approaching that of schemes based on offline-generated optimal pulse patterns. However, long prediction horizons often prohibitively increase computational load. A different approach to maximizing harmonic performance is taken in this paper. It is shown that shaping the output voltage spectra using a simple feedback mechanism can significantly reduce the length of the required prediction horizon, facilitating a feasible computational load. When a short-horizon cost function is augmented by the feedback mechanism an excellent tradeoff between harmonic performance and switching loss is achieved, even with a prediction horizon of one. It is also shown that the feedback mechanism can be used to improve input reference tracking. Experimental verification of the proposed modulator is performed on a two-level three-phase inverter. [ABSTRACT FROM AUTHOR]

Several applications such as power supplies for electric precipitators, ozone generation, partial discharge, etc., require ac superimposed dc (ACsDC) voltage supply. Most of such applications use intransigent systems for producing ACsDC voltages. In this paper, three different kinds of flexible power electronic converters are proposed for producing ACsDC voltages. These converters have two power conversion stages: input and output. In the input stage, two isolated dc voltages are obtained by using an isolated three-port dc–dc converter or two isolated two-port dc–dc converters. In the output stage, one of the input-stage dc voltages is used to generate an ac voltage and the obtained ac voltage is added to the remaining input-stage dc voltage to obtain an ACsDC voltage. Based on the converters used in the input stage, the proposed ACsDC converters are named as a dual active bridge (DAB) converter-based ACsDC converter (DAB-ACsDC), triple port active bridge (TAB) converter-based ACsDC converter (TAB-ACsDC), and dual transformer-based asymmetrical triple port active bridge (DT-ATAB) converter-based ACsDC converter (DTATAB-ACsDC). A detailed analysis of these ACsDC converters and their verifications using simulations and experimental studies are presented, which depict that the proposed converters can be used effectively for producing ACsDC voltages. [ABSTRACT FROM AUTHOR]

In this paper, a new carrier-based pulse width modulation (PWM) strategy providing common-mode voltage (CMV) elimination and reduced current ripple in a three-level neutral-point-clamped inverter is introduced. The employed switching sequences are made up of the three zero CMV (ZCMV) vectors, and one among the three vec-tors is applied at two ends of a half-carrier cycle. The output current ripple characteristics pertaining to those switching sequences are investigated. In a carrier cycle, the root-mean-square current ripple minimization is analyzed and an optimal sequence is derived accordingly. The presented PWM scheme results in a considerably reduced current harmonic distortion in a wide modulation region as compared to the two existing ZCMV schemes on the same average switching frequency. Also, an implementation of sawtooth-carrier-based PWM patterns is proposed for further improvement of the harmonic performance. The algorithm requires small computational burden and is straightforward for an online implementation. Simulation and experimental results are both provided to validate the good performance of the proposed PWM method. [ABSTRACT FROM PUBLISHER]

To achieve precise voltage value for modern model-based motor control strategies, an accurate voltage distortion compensation method for voltage source inverters is proposed in this paper. The voltage distortion principles of a mosfet-based inverter and an IGBT-based inverter are analyzed and compared. A graphical solution of compensating voltage error is proposed, all the voltage distortion factors are considered. A current observer is designed to overcome time delay, achieve precise current in each switching period for compensation. The proposed method is of high precision, intuitive, and easy to implement. The effectiveness of the proposed method is verified by experiments. [ABSTRACT FROM PUBLISHER]

The impedance-source network converter, utilizing a unique LC network and previously forbidden shoot-through states, provides the ability to buck and boost the input voltage in a single stage. However, the inrush shoot-through current (STC) in startup or transient process might cause undesired current stresses on converter devices. This paper focuses on the STC sensing for an effective inrush current limitation by the combined current sensing technique in the quasi-Z-source inverter. STC and phase currents for the inverter control strategy are obtained simultaneously. No extra hardware is needed and the effects of current sensor bandwidth and duty cycle on the sensing accuracy are analyzed mathematically. The voltage spike gets avoided by integrating the stray inductance into the impedance network. Finally, an STC control loop based on proposed method are embedded in the field-oriented control strategy. The inrush STC and the device current stress in the transient process get suppressed. Simulation and experimental results from a quasi-Z-source inverter validate the feasibility of the proposed methods. [ABSTRACT FROM PUBLISHER]

In the paper by Chen et al. (IEEE Trans. Ind. Electron., vol. 66, no. 4, pp. 2837–2846, Apr. 2019), the authors proposed two fault-tolerant control strategies for T-type three-level inverters considering neutral-point (NP) voltage oscillations. However, some basic problems are worth being discussed about the proposed fault-tolerant control methods. This letter presents some comments and results concerning the paper by Chen et al. [ABSTRACT FROM AUTHOR]

In this paper, a new cascade switch-ladder multilevel inverter topology is presented which can generate a large number of output voltage levels. First, a fundamental switch-ladder multilevel inverter structure is described. Then, the structure of recommended cascade topology based on series connection of fundamental switch-ladder topologies is presented. To generate maximum number of levels with minimum number of switching elements, dc sources, and voltage on switches, the proposed cascade topology is optimized. Comparison results prove that the presented cascade topology requires fewer numbers of components. Also, the value of voltage rating on switches is less than other structures. Experimental results for two topologies are analyzed to verify the performance of the proposed topology. [ABSTRACT FROM PUBLISHER]

A new concept of dual-dc-port asymmetrical multilevel inverter (DP-AMI), which is able to interface a low-voltage dc port, a high-voltage dc port, and an ac port simultaneously using only one topology, is presented in this paper. A systematic method to derive the DP-AMI is proposed. With the proposed DP-AMI, a low-voltage dc source, e.g., photovoltaic (PV) modules or battery, can directly supply power to the ac load within single-stage power conversion. Therefore, in comparison with a traditional two-stage dc/ac power conversion system, the power conversion stages are reduced and the voltage/current stress of the front-end dc/dc converter can be significantly alleviated, which can improve the overall conversion efficiency dramatically. Furthermore, by using the low-voltage dc source as a new voltage level, asymmetrical multiple voltage levels are generated by the proposed DP-AMI, which is beneficial for the reducing switching losses and the size/volume of the output filter. The topology derivation method of the DP-AMIs is presented. The operation principles, modulation schemes, and characteristics of one of the proposed DP-AMIs are analyzed in detail. A 1-kW prototype is built and tested to verify the effectiveness and advantages of the proposed method. [ABSTRACT FROM PUBLISHER]

This paper proposes a unique carrier-based pulse width modulation strategy for a three-level neutral-point-clamped inverter that works satisfactorily and with uniform convergence time over the full power factor (PF) range of the load variation. It has excellent control over capacitor voltages and mitigates low-frequency oscillations in the neutral point for the full PF range. First, an investigation is made to see how the load currents get modulated to generate compensating neutral current causing charging and discharging of dc-link capacitors. It is observed that when an additional modulating voltage signal that is in phase with the corresponding phase current is added in each phase, a neutral current is produced in the right direction which can be used to compensate for any prior unbalance in capacitor voltages. It is demonstrated that the performance of this scheme is insensitive to the load PF variation (full range from zero to unity). It performs satisfactorily throughout the entire linear modulation range and eliminates any undesirable low-frequency harmonic component in the compensating neutral current. The effectiveness of the proposed scheme is verified through simulation and experimental results by varying load PF as well as modulation index with both passive and motor loads. [ABSTRACT FROM PUBLISHER]

This paper presents a new family of hybrid Z-source boost dc–dc converters intended for photovoltaic applications, where the high step-up dc–dc converters are demanded to boost the low-source voltages to a predefined grid voltage. Because the boost capabilities of the traditional Z-source networks are limited, the proposed converters are composed of combine traditional Z-source networks in different ways to enhance the boost abilities of the traditional Z-source networks. The new version of the proposed Z-source converters is termed as hybrid Z-source boost dc–dc converters to satisfy the traditional benefits of Z-source networks with stronger voltage boost abilities which can also be applied to dc–ac, ac–ac, and ac–dc power conversions. The performances of the proposed converters are compared with other Z-source networks behaviors. The simulation and experimental results of the proposed converters are validated at different operating conditions. [ABSTRACT FROM PUBLISHER]

Compensation of nonlinear effects generated by dead-time and semiconductors voltage drop has been widely studied in the literature about two-level converters. This paper takes a closer look at those analyses for multilevel converters, specifically for a cascaded H-bridge (CHB) converter modulated with phase-shifted pulse width modulation. The interaction between the cells is analyzed for a generic $n$ -cell converter, from which a general expression for the distortion generated by the nonlinearities has been obtained. Based on this expression, a compensation signal for the overall converter is calculated on each sample time, which is a fraction of the triangular carrier used to modulate each cell, thus significantly improving the quality of the output voltage signals. Experimental validation of the proposed compensation method is presented using a three-phase four-cell CHB converter prototype of 5.5 kW. [ABSTRACT FROM AUTHOR]

Space vector modulation (SVM) control of multilevel inverters (MLIs) is very popular. However, it gets extremely challenging with the increase in the number of output voltage levels due to the emergence of subtriangles in the various sectors of the hexagon, which results in increased computational complexity and storage requirements of switching states and corresponding pulse durations. Currently, this is handled through laborios offline computations in conjunction with the visual inspection of the space vector hexagon and its various sectors. This paper aims to simplify the implementation of the SVM scheme for an n-level MLI by proposing generalized equations that not only facilitate direct online computation of control pulses and obviate the requirement of lookup tables but also result in optimized switching. Yet, the on-time computations of the various MLI switches are still based on simple two-dimensional Cartesian co-ordinate system combined with the basic two-level inverter implementation. The proposed scheme makes use of a unique l-factor approach, which directly identifies the location of the various subtriangles in the space vector hexagon and leads to direct online computations of the control pulses. The proposed scheme is validated by simulations and experimental results for three- and five-level diode clamped MLI. [ABSTRACT FROM AUTHOR]

In this paper, a novel topology of six-level inverters for a medium-voltage high-power applications is proposed, which consists of inner flying-capacitor inverter (FCI) units and outer two-level inverter units. The proposed topology can reduce the number of devices, components, and isolated sources compared with the existing ones in the case of the same number of output voltage steps, which result in a reduction of the size and weight of the inverters. Also, the total power loss of the proposed topology is lower than that of the diode-clamped inverter (DCI) and FCI. Besides, the estimated cost of the proposed topology is about 60.5% and 81.3% compared with the DCI and FCI, respectively. In addition, the modulation technique and the control strategy for the dc-link capacitor and flying-capacitor voltages are developed for the proposed topology. The effectiveness of the proposed six-level inverter for the medium-voltage applications has been verified by simulation results. Also, the feasibility of the proposed inverter has been proved by experimental results for the prototype at the laboratory. [ABSTRACT FROM AUTHOR]

A new single-phase \uppi-\texttype 5-level inverter using 3-terminal switch-network (3TSN) is proposed in this paper. The topology is considered as a variant of T-type 3-level structure or dual-buck inverter with coupled inductors. This new inverter is suitable for multilevel power inversion with low dc-bus voltage. The merit of the proposed topology is to apply only four active power switches to achieve 5-level operation. Other benefits include double frequency operation of output inductor and equal division of the current that flows through power switches and filter inductor. Hence, it leads to high efficiency and low harmonics. These characteristics allow improvement of losses distribution and volume reduction of output filter inductor. The operation scenario with sinusoidal pulsewidth modulation (SPWM) is described in details. Meanwhile, the magnetic analysis and design are studied and discussed. Finally, a prototype is built to verify the theoretical analysis and demonstrate the benefits of the proposed topology. [ABSTRACT FROM AUTHOR]

In this paper, a model-predictive control (MPC) has been designed and implemented on the packed U-cell (PUC) inverter, which has one isolated dc source and one capacitor as an auxiliary dc link. The MPC is designed to regulate the capacitor voltage at the desired magnitude to have seven voltage levels at the output of the inverter. Since grid-connected application is targeted by this application, the inverter should be capable of supplying requested amount of active and reactive power at the point of common coupling (PCC) as well. Therefore, MPC should also consider the line-current control to monitor the exchange of reactive power with the grid while injecting appropriate active power at low total harmonic distortion (THD). Various experimental tests including change in dc-source voltage, active power variation, and operation at different power factor (PF) have been performed on a laboratory prototype to validate the good performance obtained by the proposed MPC. The dynamic performance of the controller during sudden changes in dc capacitor voltage, supply current, and PF demonstrates the fast and accurate response and the superior operation of the proposed controller. [ABSTRACT FROM PUBLISHER]

This paper presents a model predictive control (MPC) scheme for quasi-Z-source (qZS) three-phase four-leg inverter. In order to cope with the drawbacks of traditional voltage source inverters (VSIs), a qZS three-phase four-leg inverter topology is proposed. This topology features a wide range of voltage gain which is suitable for applications in renewable energy-based power systems, where the output of the renewable energy sources varies widely with operating conditions such as wind speed, temperature, and solar irradiation. To improve the capability of the controller, an MPC scheme is used which implements a discrete-time model of the system. The controller handles each phase current independently, which adds flexibility to the system. Simulation and experimental studies verify the performances of the proposed control strategy under balanced and unbalanced load conditions as well as single-phase open-circuit fault condition. [ABSTRACT FROM PUBLISHER]

In this paper, a new topology for half-bridge switched boost inverter (HB-SBI) is proposed. The proposed half-bridge inverter uses more active elements rather than capacitors and inductors in comparison with the conventional half-bridge Z-source inverter with two Z-networks, which results in reduction of weight, size, and cost. Moreover, the proposed inverter has the capability of eliminating inverter leg short-circuit issues and is able to further increase the output voltage level in comparison with its conventional types. Generating zero-level output voltage is also another advantage of this topology. Based on theoretical calculations, the steady-state and small-signal analysis of the proposed topology in different operating modes are performed and the ripple of inductors’ current and capacitors’ voltage are also calculated. A comprehensive comparison is also made between the proposed inverter and the conventional types. Finally, the experimental results are provided to reconfirm the performance of the proposed inverter. [ABSTRACT FROM PUBLISHER]

The flying capacitor multilevel inverter (FCMLI) is one of the well-known structures of multilevel inverters having attracted considerable attention because of its merits. In spite of its many advantages, it has some limitations such as high volume and complicated control method because of its bulky capacitors and their voltage balancing requirement. Moreover, the high number of power semiconductors required makes this structure susceptible to failure. To increase the ratio of the number of levels to the number of components, an uneven distribution of capacitor voltages has been suggested in previous reports; however, this approach complicates the control method. Up to now, almost all presented methods suffer from high computational load and/or structure-dependent algorithm. In this paper, a simple state-based and structure-independent method is proposed for capacitor voltage regulation. The proposed method is straightforward and can perform online computation of switching sequences in a computationally efficient manner without any need for stored information or look-up tables. The method is conveniently extendible to any number of cells and levels in an FCMLI structure with arbitrary dc link voltage distribution schemes. Simulation and experimental results show the effectiveness and simplicity of this method. [ABSTRACT FROM PUBLISHER]

In this paper, a common grounded Z-source dc–dc converter with high voltage gain is proposed for photovoltaic (PV) applications, which require a relatively high output–input voltage conversion ratio. Compared with the traditional Z-source dc–dc converter, the proposed converter, which employs a conventional Z-source network, can obtain higher voltage gain and provide the common ground for the input and output without any additional components, which results in low cost and small size. Moreover, the proposed converter features low voltage stresses of the switch and diodes. Therefore, the efficiency and reliability of the proposed converter can be improved. The operating principle, parameters design, and comparison with other converters are analyzed. Simulation and experimental results are given to verify the aforementioned characteristics and theoretical analysis of the proposed converter. [ABSTRACT FROM PUBLISHER]

In this paper, a new inverter topology is proposed for generating a multilevel dodecagonal voltage space vector structure for open-end winding induction motor (IM) using a single dc source. Dodecagonal voltage space vector structure eliminates fifth- and seventh-order harmonic voltages from phase voltage output and hence eliminates the fifth- and seventh-order harmonic currents through the motor leading to removal of the dominant sixth-order torque ripple generation in the motor over the entire modulation range. Multilevel space vector structure generates output voltage with better THD and low dv/dt. In the proposed topology, two three-level inverters drive an open-end winding IM, one inverter from each side. DC-link of primary inverter is from a dc source which delivers the entire active power, whereas the secondary inverter dc-link is maintained by a capacitor, which is self balanced during the inverter operation. The PWM scheme implemented ensures low switching frequency for primary inverter. Secondary inverter operates at a small dc-link voltage. Hence, switching losses are small for both primary and secondary inverters. Experimental results show the elimination of fifth- and seventh-order harmonic voltages over the entire modulation range, validating effectiveness of the proposed multilevel inverter scheme. [ABSTRACT FROM PUBLISHER]

A four-level open-end winding induction motor (OEWIM) drive is known to suffer from two perennial problems. One is the problem of zero-sequence currentin the motor phases, which is caused by the existence of zero-sequence voltage in them. The other is the overcharging of the dc-link capacitor of theinverter operated with lower dc-link voltage by its counterpart operated with a higher dc-link voltage. This paper investigates the applicability of aspecial variant of space vector pulse width modulation (SVPWM) scheme for a recently proposed power circuit configuration, in which arectifier–inverter combination is nested within the conventional two-level inverter configuration to achieve four-level inversion. This PWM schemeis named as the sample-averaged zero-sequence elimination (SAZE) SVPWM scheme, wherein the zero sequence voltage is suppressed in each sampling timeperiod in the average sense. Both of the aforementioned problems encountered in this drive are successfully overcome for this power circuit configurationby resorting to the proposed SVPWM strategy. [ABSTRACT FROM PUBLISHER]